KTM 250 EXC-F Six Days 2013 Owner's manual
OWNER'S MANUAL 2013
250 EXC-F SIX DAYS EU
250 EXC-F EU
250 EXC-F AUS
250 XCF‑W USA
Art. no. 3211862en
DEAR KTM CUSTOMER 1
DEARKTM CUSTOMER
Congratulations on your decision to purchase a KTM motorcycle. You are now the owner of a state-of-the-art sports motorcycle that will
give you enormous pleasure if you service and maintain it accordingly.
We wish you a lot of enjoyment in riding this vehicle.
Please enter the serial number of your vehicle below.
Chassis number ( p. 11) Stamp of dealer
Engine number ( p. 11)
Key number (All EXC‑F models) ( p. 11)
The Owner's Manual contained the latest information for this model at the time of going to print. Slight deviations resulting from continuing development and design of the motorcycles can, however, not be completely excluded.
All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical specifications, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt
these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery
options, deviations from illustrations and descriptions, as well as misprints and other errors. The models portrayed partly contain special equipment that does not belong to the regular scope of delivery.
© 2012 KTM-Sportmotorcycle AG, Mattighofen Austria
All rights reserved
Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright
owner.
ISO 9001(12 100 6061)
According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead
to the maximum possible quality of the products.
Issued by: TÜV Management Service
KTM-Sportmotorcycle AG
5230 Mattighofen, Austria
TABLE OF CONTENTS 2
TABLEOF CONTENTS
1 MEANS OF REPRESENTATION ..................................... 5
1.1 Symbols used ................................................... 5
1.2 Formats used.................................................... 5
2 SAFETY ADVICE........................................................... 6
2.1 Use definition - intended use ............................. 6
2.2 Safety advice.................................................... 6
2.3 Degrees of risk and symbols ............................... 6
2.4 Tampering warning............................................ 6
2.5 Safe operation .................................................. 7
2.6 Protective clothing ............................................ 7
2.7 Work rules........................................................ 7
2.8 Environment..................................................... 7
2.9 Owner's Manual ................................................ 7
3 IMPORTANT NOTES..................................................... 8
3.1 Guarantee, warranty .......................................... 8
3.2 Operating and auxiliary substances ..................... 8
3.3 Spare parts, accessories .................................... 8
3.4 Service ............................................................ 8
3.5 Figures ............................................................ 8
3.6 Customer service............................................... 8
4 VIEW OF VEHICLE ....................................................... 9
4.1 View of vehicle, front left (example) .................... 9
4.2 View of vehicle, rear right (example) ................. 10
5 SERIAL NUMBERS .................................................... 11
5.1 Chassis number .............................................. 11
5.2 Type label ...................................................... 11
5.3 Key number (All EXC‑F models)........................ 11
5.4 Engine number ............................................... 11
5.5 Fork part number ............................................ 11
5.6 Shock absorber part number ............................ 12
6 CONTROLS................................................................ 13
6.1 Clutch lever.................................................... 13
6.2 Hand brake lever............................................. 13
6.3 Throttle grip ................................................... 13
6.4 Kill switch (All EXC‑F models) .......................... 13
6.5 Kill switch (XCF‑W) ......................................... 13
6.6 Horn button (All EXC‑F models)........................ 14
6.7 Light switch (All EXC‑F models) ....................... 14
6.8 Light switch (XCF‑W)....................................... 14
6.9 Turn signal switch (All EXC‑F models)............... 14
6.10 Emergency OFF switch (EXC‑F AUS) ................. 14
6.11 Electric starter button (EXC‑F AUS) .................. 15
6.12 Electric starter button (EXC‑F EU, EXC-F SIX
DAYS, XCF‑W) ................................................ 15
6.13 Overview of indicator lamps (All EXC‑F
models).......................................................... 15
6.14 Overview of indicator lamps (XCF‑W)................. 15
6.15 Speedometer.................................................. 16
6.15.1 Overview .................................................... 16
6.15.2 Activation and test ...................................... 16
6.15.3 Tripmaster switch ....................................... 16
6.15.4 Setting kilometers or miles .......................... 16
6.15.5 Setting the clock ........................................ 17
6.15.6 Adjusting the speedometer functions ............ 17
6.15.7 Querying lap time ....................................... 18
6.15.8 Display mode SPEED (speed)....................... 18
6.15.9 Display mode SPEED/H (operating hours)...... 18
6.15.10 Display mode SPEED/CLK (clock)................. 19
6.15.11 Display mode SPEED/LAP (lap time)............. 19
6.15.12 Display mode SPEED/ODO (odometer) .......... 19
6.15.13 Display mode SPEED/TR1 (trip master 1)...... 19
6.15.14 Display mode SPEED/TR2 (trip master 2)...... 20
6.15.15 Display mode SPEED/A1 (average speed 1) ... 20
6.15.16 Display mode SPEED/A2 (average speed 2) ... 20
6.15.17 Display mode SPEED/S1 (stop watch 1) ........ 21
6.15.18 Display mode SPEED/S2 (stop watch 2) ........ 21
6.15.19 Table of functions....................................... 21
6.15.20 Table of conditions and menu activation ....... 22
6.16 Opening filler cap ........................................... 22
6.17 Closing filler cap............................................. 22
6.18 Idle speed adjusting screw............................... 23
6.19 Shift lever ...................................................... 23
6.20 Kick starter .................................................... 23
6.21 Foot brake lever .............................................. 24
6.22 Side stand...................................................... 24
6.23 Steering lock (All EXC‑F models) ...................... 24
6.24 Locking the steering (All EXC‑F models) ............ 24
6.25 Unlocking the steering (All EXC‑F models)......... 25
7 PREPARING FOR USE................................................ 26
7.1 Advice on first use .......................................... 26
7.2 Running-in the engine ..................................... 27
7.3 Preparing the vehicle for difficult riding
conditions ...................................................... 27
7.4 Preparing for rides on dry sand......................... 28
7.5 Preparing for rides on wet sand ........................ 28
7.6 Preparing for rides on wet and muddy
surfaces ......................................................... 29
7.7 Preparing for rides at high temperature and
slow speed ..................................................... 29
7.8 Preparing for rides at low temperature or in
snow.............................................................. 29
8 RIDING INSTRUCTIONS............................................. 30
8.1 Checks and maintenance work when preparing
for use ........................................................... 30
8.2 Starting.......................................................... 30
8.3 Starting off..................................................... 31
8.4 Shifting, riding ............................................... 31
8.5 Braking.......................................................... 31
8.6 Stopping, parking............................................ 32
8.7 Transport ....................................................... 32
8.8 Refueling ....................................................... 33
9 SERVICE SCHEDULE ................................................. 34
9.1 Service schedule............................................. 34
9.2 Service work (as additional order) ..................... 35
10 TUNING THE CHASSIS .............................................. 36
10.1 Checking the basic suspension setting against
the rider's weight ............................................ 36
10.2 Compression damping of shock absorber ........... 36
10.3 Adjusting the low-speed compression damping
of the shock absorber ...................................... 36
10.4 Adjusting the high-speed compression
damping of the shock absorber ......................... 37
10.5 Adjusting the rebound damping of the shock
absorber......................................................... 37
10.6 Measuring rear wheel sag unloaded................... 38
10.7 Checking the static sag of the shock absorber.... 38
10.8 Checking the riding sag of the shock absorber.... 38
10.9 Adjusting the spring preload of the shock
absorber x.................................................... 39
10.10 Adjusting the riding sag x .............................. 39
10.11 Checking basic setting of fork .......................... 40
10.12 Adjusting the compression damping of the
fork ............................................................... 40
10.13 Adjusting the rebound damping of the fork ........ 41
TABLE OF CONTENTS 3
10.14 Adjusting the spring preload of the fork
(EXC‑F EU, EXC‑F AUS, XCF‑W) ....................... 42
10.15 Handlebar position.......................................... 42
10.16 Adjusting handlebar position x....................... 42
11 SERVICE WORK ON THE CHASSIS.............................. 44
11.1 Raising the motorcycle with the lift stand .......... 44
11.2 Removing the motorcycle from the lift stand ...... 44
11.3 Bleeding fork legs ........................................... 44
11.4 Cleaning the dust boots of the fork legs............. 44
11.5 Loosening the fork protector............................. 45
11.6 Positioning the fork protection.......................... 45
11.7 Removing the fork legs .................................... 45
11.8 Installing the fork legs x ................................ 46
11.9 Removing the fork protector x ........................ 47
11.10 Installing the fork protector x......................... 47
11.11 Removing the lower triple clamp x
(EXC‑F EU, EXC‑F AUS, XCF‑W) ....................... 47
11.12 Removing the lower triple clamp x (EXC-F
SIX DAYS)...................................................... 48
11.13 Installing the lower triple clamp x (EXC‑F EU,
EXC‑F AUS, XCF‑W) ........................................ 49
11.14 Installing the lower triple clamp x (EXC-F SIX
DAYS)............................................................ 51
11.15 Checking the steering head bearing play............ 52
11.16 Adjusting the play of the steering head
bearing x (EXC‑F EU, EXC‑F AUS, XCF‑W)....... 53
11.17 Adjusting the play of the steering head
bearing x (EXC-F SIX DAYS)........................... 53
11.18 Greasing the steering head bearing x .............. 54
11.19 Removing the front fender ............................... 54
11.20 Installing the front fender ................................ 54
11.21 Removing the shock absorber x ...................... 54
11.22 Installing the shock absorber x....................... 55
11.23 Removing the seat .......................................... 55
11.24 Mounting the seat ........................................... 55
11.25 Removing the air filter box lid .......................... 55
11.26 Installing the air filter box lid ........................... 56
11.27 Removing the air filter x ................................ 56
11.28 Installing the air filter x................................. 56
11.29 Cleaning the air filter and air filter box x ......... 57
11.30 Sealing the air filter box x.............................. 57
11.31 Removing main silencer................................... 57
11.32 Installing the main silencer.............................. 58
11.33 Changing the glass fiber yarn filling of the
main silencer x............................................. 58
11.34 Removing the fuel tank x............................... 59
11.35 Installing the fuel tank x................................ 60
11.36 Checking for chain dirt accumulation ................ 61
11.37 Cleaning the chain .......................................... 61
11.38 Checking the chain tension .............................. 62
11.39 Adjusting the chain tension.............................. 62
11.40 Checking the chain, rear sprocket, engine
sprocket and chain guide ................................. 63
11.41 Adjusting the chain guide x ........................... 65
11.42 Checking the frame x .................................... 65
11.43 Checking the swingarm x............................... 65
11.44 Checking the throttle cable routing ................... 66
11.45 Checking the rubber grip ................................. 66
11.46 Additionally securing the rubber grip................. 66
11.47 Adjusting the basic position of the clutch
lever .............................................................. 67
11.48 Checking/correcting the fluid level of the
hydraulic clutch.............................................. 67
11.49 Changing the hydraulic clutch fluid x.............. 67
11.50 Removing the engine guard (EXC‑F AUS,
EXC-F SIX DAYS) ............................................ 68
11.51 Installing the engine guard (EXC‑F AUS, EXC-F
SIX DAYS)...................................................... 68
12 BRAKE SYSTEM ........................................................ 69
12.1 Checking free travel of hand brake lever ............ 69
12.2 Adjusting free travel of hand brake lever (All
EXC‑F models)................................................ 69
12.3 Adjusting the basic position of the hand brake
lever (XCF‑W) ................................................. 69
12.4 Checking the brake discs ................................. 70
12.5 Checking the front brake fluid level .................. 70
12.6 Adding front brake fluid x.............................. 70
12.7 Checking the front brake linings ....................... 71
12.8 Changing the front brake linings x .................. 71
12.9 Checking the free travel of foot brake lever ........ 73
12.10 Adjusting the basic position of the foot brake
lever x ......................................................... 73
12.11 Checking the rear brake fluid level.................... 74
12.12 Adding brake fluid to the rear brake
circuit x....................................................... 74
12.13 Checking the rear brake linings ........................ 75
12.14 Changing the rear brake linings x ................... 76
13 WHEELS, TIRES ........................................................ 78
13.1 Removing the front wheel x ........................... 78
13.2 Installing the front wheel x ............................ 78
13.3 Removing the rear wheel x............................. 79
13.4 Installing the rear wheel x.............................. 79
13.5 Checking the tire condition .............................. 80
13.6 Checking tire air pressure ................................ 81
13.7 Checking spoke tension ................................... 81
14 ELECTRICAL SYSTEM ................................................ 83
14.1 Removing the battery x.................................. 83
14.2 Installing the battery x .................................. 83
14.3 Charging the battery x................................... 83
14.4 Changing the main fuse................................... 84
14.5 Changing the fuses of individual power
consumers...................................................... 85
14.6 Changing the fuse of the radiator fan (EXC-F
SIX DAYS)...................................................... 86
14.7 Removing headlight mask with headlight........... 87
14.8 Refitting the headlight mask with the
headlight........................................................ 87
14.9 Changing the headlight bulb ............................ 87
14.10 Changing the turn signal bulb .......................... 88
14.11 Checking the headlight setting ......................... 89
14.12 Adjusting the headlight range........................... 89
14.13 Changing the speedometer battery .................... 89
15 COOLING SYSTEM ..................................................... 91
15.1 Cooling system ............................................... 91
15.2 Checking the antifreeze and coolant level .......... 91
15.3 Checking the coolant level ............................... 92
15.4 Draining the coolant x................................... 92
15.5 Refilling coolant x......................................... 93
16 TUNING THE ENGINE................................................ 94
16.1 Checking the play in the throttle cable .............. 94
16.2 Adjusting the play in the throttle cable x......... 94
16.3 Adjusting the idle speed x ............................. 95
16.4 Checking the basic position of the shift lever ..... 95
TABLE OF CONTENTS 4
16.5 Adjusting the basic position of the shift
lever x ......................................................... 95
17 SERVICE WORK ON THE ENGINE ............................... 96
17.1 Changing the fuel screen x ............................ 96
17.2 Checking the engine oil level............................ 96
17.3 Changing the engine oil and oil filter, cleaning
the oil screens x ........................................... 97
17.4 Adding engine oil............................................ 99
18 CLEANING, CARE .................................................... 100
18.1 Cleaning the motorcycle ................................ 100
18.2 Checks and maintenance steps for winter
operation...................................................... 101
19 STORAGE................................................................ 102
19.1 Storage........................................................ 102
19.2 Preparing for use after storage........................ 102
20 TROUBLESHOOTING ............................................... 103
21 BLINK CODE ........................................................... 105
22 TECHNICAL DATA.................................................... 107
22.1 Engine......................................................... 107
22.2 Engine tightening torques .............................. 107
22.3 Capacities.................................................... 109
22.3.1 Engine oil ................................................ 109
22.3.2 Coolant.................................................... 109
22.3.3 Fuel ........................................................ 109
22.4 Chassis........................................................ 109
22.5 Electrical system........................................... 110
22.6 Tires............................................................ 110
22.7 Fork............................................................. 110
22.7.1 EXC‑F EU, EXC‑F AUS, XCF‑W ................... 110
22.7.2 EXC-F SIX DAYS ....................................... 111
22.8 Shock absorber ............................................. 111
22.9 Chassis tightening torques ............................. 112
23 SUBSTANCES ......................................................... 114
24 AUXILIARY SUBSTANCES ........................................ 116
25 STANDARDS ........................................................... 118
INDEX ............................................................................ 119
1 MEANS OF REPRESENTATION 5
1.1 Symbols used
The meaning of specific symbols is described below.
Indicates an expected reaction (e.g. of a work step or a function).
Indicates an unexpected reaction (e.g. of a work step or a function).
All work marked with this symbol requires specialist knowledge and technical understanding. In the interest of
your own safety, have these jobs performed by an authorized KTM workshop. There, your motorcycle will be optimally cared for by specially trained experts using the specialist tools required.
Indicates a page reference (more information is provided on the specified page).
1.2 Formats used
The typographical formats used in this document are explained below.
Specific name Identifies a proprietary name.
®
Name
Brand™ Identifies a brand available on the open market.
Identifies a protected name.
2 SAFETY ADVICE 6
2.1 Use definition - intended use
(All EXC‑F models)
KTM sport motorcycles are designed and built to withstand the normal stresses and strains of competitive use. The motorcycles
comply with currently valid regulations and categories of the top international motorsport organizations.
Info
The motorcycle is authorized for public road traffic in the homologous (reduced) version only.
In the derestricted version, the motorcycle must be used only on closed off property remote from public road traffic.
This motorcycle is designed for use in offroad endurance competition and not primarily for use in motocross.
(XCF‑W)
KTM sport motorcycles are designed and built to withstand the normal stresses and strains of competitive use. The motorcycles
comply with currently valid regulations and categories of the top international motorsport organizations.
Info
This motorcycle is designed for use in offroad endurance competition and not primarily for use in motocross.
2.2 Safety advice
A number of safety instructions need to be followed to operate the vehicle safely. Therefore, read this manual carefully. The safety
instructions are highlighted in the text and are referred to at the relevant passages.
Info
The vehicle has various information and warning labels at prominent locations. Do not remove information/warning labels. If
they are missing, you or others may not recognize dangers and may therefore be injured.
2.3 Degrees of risk and symbols
Danger
Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures
are not taken.
Warning
Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.
Caution
Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.
Note
Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.
Warning
Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.
2.4 Tampering warning
Tampering with the noise control system is prohibited. Federal law prohibits the following acts or the causing thereof:
1 The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device
or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate
purchaser or while it is in use, or
2 the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
Among those acts presumed to constitute tampering are the acts listed below:
1 Removal of, or puncturing the main silencer, baffles, header pipes or any other components which conduct exhaust gases.
2 Removal or puncturing of any part of the intake system.
3 Lack of proper maintenance.
4 Replacing any moving part of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the
manufacturer.
2 SAFETY ADVICE 7
2.5 Safe operation
Danger
Danger of accidents Danger arising from the rider's judgement being impaired.
– Do not operate the vehicle while under the influence of alcohol, drugs and certain medications or physically or mentally
impaired.
Danger
Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death.
– When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed
space without an effective exhaust extraction system.
Warning
Danger of burns Some vehicle components become very hot when the vehicle is operated.
– Do not touch hot components such as exhaust system, radiator, engine, shock absorber, and the brake system. Allow these
components to cool down before starting work on them.
Only operate the vehicle when it is in perfect technical condition, in accordance with its intended use, and in a safe and environmentally compatible manner.
An appropriate driver's license is needed to ride the vehicle on public roads.
Have malfunctions that impair safety promptly eliminated by an authorized KTM workshop.
Adhere to the information and warning labels on the vehicle.
2.6 Protective clothing
Warning
Risk of injury Missing or poor protective clothing presents an increased safety risk.
– Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always
wear protective clothing that is in good condition and meets the legal requirements.
In the interest of your own safety, KTM recommends that you only operate the vehicle while wearing protective clothing.
2.7 Work rules
Special tools are necessary for certain tasks. The tools are not contained in the vehicle but can be ordered under the number in parentheses. E.g.: bearing puller (15112017000)
During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals and seal rings, O-rings, pins, lock washers) must be
replaced by new parts.
In some instances, a thread locker (e.g. Loctite®) is required. The manufacturer instructions for use must be followed.
After disassembly, clean the parts that are to be reused and check them for damage and wear. Change damaged or worn parts.
After you complete the repair or service work, check the operating safety of the vehicle.
2.8 Environment
If you use your motorcycle responsibly, you can ensure that problems and conflicts do not occur. To protect the future of the motorcycle sport, make sure that you use your motorcycle legally, display environmental consciousness, and respect the rights of others.
When disposing of used oil, other operating and auxiliary fluids, and used components, comply with the laws and regulations of the
respective country.
Because motorcycles are not subject to the EU regulations governing the disposal of used vehicles, there are no legal regulations that
pertain to the disposal of an end-of-life motorcycle. Your authorized KTM dealer will be glad to advise you.
2.9 Owner's Manual
It is important that you read this Owner's Manual carefully and completely before making your first trip. The Owner's Manual contains
useful information and many tips on how to operate, handle, and maintain your motorcycle. Only then will you find out how to customize the vehicle ideally for your own use and how you can protect yourself from injury.
Keep the Owner's Manual in an accessible place to enable you to refer to it as needed.
If you would like to know more about the vehicle or have questions on the material you read, please contact an authorized KTM dealer.
The Owner's Manual is an important component of the vehicle and should be handed over to the new owner if the vehicle is sold.
3 IMPORTANT NOTES 8
3.1 Guarantee, warranty
The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the customer's
service record and in the KTM dealer.net; otherwise, all warranty claims will be void. No warranty claims can be considered for damage
resulting from manipulations and/or alterations to the vehicle.
Additional information on the guarantee or warranty and the procedures involved can be found in the service record.
3.2 Operating and auxiliary substances
Warning
Environmental hazard Improper handling of fuel is a danger to the environment.
– Do not allow fuel to get into the ground water, the ground, or the sewage system.
Use operating and auxiliary substances (such as fuel and lubricants) as specified in the Owner's Manual.
3.3 Spare parts, accessories
For your own safety, only use spare parts and accessory products that are approved and/or recommended by KTM and have them
installed by an authorized KTM workshop. KTM accepts no liability for other products and any resulting damage or loss.
Certain spare parts and accessory products are specified in parentheses in the descriptions. Your KTM dealer will be glad to advise
you.
The current KTM PowerParts for your vehicle can be found on the KTM website.
International KTM Website: http://www.ktm.com
3.4 Service
A prerequisite for perfect operation and prevention of premature wear is that the service, care, and tuning work on the engine and
chassis is properly carried out as described in the Owner's Manual. Incorrect adjustment and tuning of the engine and chassis can
lead to damage and breakage of components.
Use of the vehicle under difficult conditions, such as on sand or on wet and muddy surfaces, can lead to considerably more rapid wear
of components such as the drive train, brake system, or suspension components. For this reason, it may be necessary to inspect or
replace parts before the next scheduled service.
It is imperative that you adhere to the stipulated run-in times and service intervals. If you observe these exactly, you will ensure a
much longer service life for your motorcycle.
3.5 Figures
The figures contained in the manual may depict special equipment.
In the interest of clarity, some components may be shown disassembled or may not be shown at all. It is not always necessary to disassemble the component to perform the activity in question. Please follow the instructions in the text.
3.6 Customer service
Your authorized KTM dealer will be happy to answer any questions you may have on your vehicle and KTM.
A list of authorized KTM dealers can be found on the KTM website.
International KTM Website: http://www.ktm.com
4 VIEW OF VEHICLE 9
4.1 View of vehicle, front left (example)
1 Filler cap
2 Air filter box lid
3 Fork compression adjustment
4 Shift lever ( p. 23)
5 Engine number ( p. 11)
6 Side stand ( p. 24)
L00001-01
4 VIEW OF VEHICLE 10
4.2 View of vehicle, rear right (example)
1 Kill switch ( p. 13)
1 Horn button ( p. 14)
1 Light switch ( p. 14)
1 Turn signal switch ( p. 14)
2 Emergency OFF switch ( p. 14)
2 Electric starter button ( p. 15)
3 Throttle grip ( p. 13)
4 Fork rebound adjustment and spring preload adjustment
5 Shock absorber rebound adjustment
6 Level viewer for brake fluid, rear
7 Shock absorber compression adjustment
8 Level viewer, engine oil
9 Foot brake lever ( p. 24)
10 Kick starter ( p. 23)
L00002-01
5 SERIAL NUMBERS 11
5.1 Chassis number
The chassis number 1 is stamped on the steering head on the right.
C00125-10
5.2 Type label
(XCF‑W)
The type label 1 is fixed to the front of the steering head.
101290-10
5.3 Key number (All EXC‑F models)
500125-10
5.4 Engine number
The key number 1 for the steering lock is stamped onto the key connector.
The engine number 1 is stamped on the left side of the engine under the engine
sprocket.
5.5 Fork part number
101435-10
The fork part number 1 is stamped on the inner side of the fork stub.
101654-10
5 SERIAL NUMBERS 12
5.6 Shock absorber part number
The shock absorber part number 1 is stamped on the top of the shock absorber above
the adjusting ring on the engine side.
101436-10
6 CONTROLS 13
6.1 Clutch lever
The clutch lever 1 is fitted on the left side of the handlebar.
The clutch is hydraulically operated and self-adjusting.
101628-10
6.2 Hand brake lever
Hand brake lever 1 is located on the right side of the handlebar.
The hand brake lever is used to activate the front brake.
101629-10
6.3 Throttle grip
101630-10
6.4 Kill switch (All EXC‑F models)
The throttle grip 1 is fitted on the right side of the handlebar.
Kill switch 1 is fitted on the left side of the handlebar.
Possible states
• Kill switch in basic position – the ignition circuit is closed in this position and
the engine can be started.
• Kill switch pressed – the ignition circuit is open in this position, the engine
goes out if it was running, or does not start if it was off.
6.5 Kill switch (XCF‑W)
101631-10
Kill switch 1 is fitted on the left side of the handlebar.
Possible states
• Kill switch in basic position – the ignition circuit is closed in this position and
the engine can be started.
• Kill switch pressed – the ignition circuit is open in this position, the engine
goes out if it was running, or does not start if it was off.
101646-10
6 CONTROLS 14
6.6 Horn button (All EXC‑F models)
The horn button 1 is fitted on the left side of the handlebar.
Possible states
• Horn button in neutral position
• Horn button pressed – the horn is actuated in this position.
101631-11
6.7 Light switch (All EXC‑F models)
The light switch 1 is fitted on the left side of the handlebar.
Possible states
Light off – Light switch is turned to the right. In this position, the light
is switched off.
Low beam on – Light switch is in the central position. In this position,
the low beam and tail light are switched on.
High beam on – Light switch is turned to the left. In this position, the
101632-10
high beam and the tail light are switched on.
6.8 Light switch (XCF‑W)
The light switch 1 is on the right of the speedometer.
Possible states
• Light off – Light switch is pressed in up to the stop. In this position, the light is
switched off.
• Light on – Light switch is pulled out to the stop. In this position, the low beam
and tail light are switched on.
101303-10
6.9 Turn signal switch (All EXC‑F models)
Turn signal switch 1 is fitted on the left side of the handlebar.
Possible states
101633-10
Turn signal light off – Turn signal switch is in the central position.
Turn signal light, left, on – Turn signal switch is turned to the left.
Turn signal light, right, on – Turn signal switch is turned to the right.
6.10 Emergency OFF switch (EXC‑F AUS)
The emergency OFF switch 1 is fitted on the right side of the handlebar.
Possible states
101634-10
Ignition off – the ignition circuit is open in this position, the engine
goes out if it was running, or does not start if it was off.
Ignition on – the ignition circuit is closed in this position and the
engine can be started.
6 CONTROLS 15
6.11 Electric starter button (EXC‑F AUS)
The electric starter button 1 is fitted on the right side of the handlebar.
Possible states
• Electric starter button in basic position
• Electric starter button pressed – the electric starter is actuated in this position.
101634-11
6.12 Electric starter button (EXC‑F EU, EXC-F SIX DAYS, XCF‑W)
The electric starter button 1 is fitted on the right side of the handlebar.
Possible states
• Electric starter button in basic position
• Electric starter button pressed – the electric starter is actuated in this position.
101635-10
6.13 Overview of indicator lamps (All EXC‑F models)
Possible states
High beam indicator light lights up blue – High beam is switched on.
FI warning lamp (MIL) lights up/flashes orange – The OBD has detected
an emission- or safety-critical fault.
The fuel level warning lamp lights up orange – The fuel level has
reached the reserve mark.
101304-01
Turn signal indicator light flashes green – Turn signal is switched on.
6.14 Overview of indicator lamps (XCF‑W)
Possible states
FI warning lamp (MIL) lights up/flashes orange – The OBD has detected
an emission- or safety-critical fault.
The fuel level warning lamp lights up orange – The fuel level has
reached the reserve mark.
101302-01
6 CONTROLS 16
6.15 Speedometer
6.15.1 Overview
– Press the button to change the display mode or change to one of the Setup
menus.
– Press the button to control different functions.
– Press the button to control different functions.
Info
When the vehicle is delivered, only the SPEED/H and SPEED/ODO display modes
are activated.
400312-01
6.15.2 Activation and test
Activating the speedometer
The speedometer is activated when one of the buttons is pressed or an impulse comes
from the wheel speed sensor.
Display test
To enable you to check that the display is functioning properly, all display segments
light up briefly.
400313-01
WS (wheel size)
After the display function check, the wheel size WS is displayed briefly.
Info
The number 2205 equals the circumference of the 21" front wheel with standard tires.
The display then changes to the last selected mode.
400314-01
6.15.3 Tripmaster switch
(Option: Tripmaster switch)
The tripmaster switch is used to control the functions of the speedometer from the handlebar.
Info
The trip master is an optional accessory.
6.15.4 Setting kilometers or miles
Info
If you change the unit of measure, the ODO value is retained and converted accordingly.
The values TR1, TR2, A1, A2 and S1 are cleared when the unit of measure is changed.
400329-01
Condition
The motorcycle is stationary.
– Press the button briefly and repeatedly until H appears at the bottom right of the
display.
– Press the button for 3 - 5 seconds.
The Setup menu is displayed and the active functions are shown.
– Press the button repeatedly until the Km/h/Mph display flashes.
Adjusting Km/h
– Press the button .
6 CONTROLS 17
Adjusting Mph
– Press the button .
– Press the button for 3 - 5 seconds.
The settings are stored and the Setup menu is closed.
Info
If no button is pressed for 20 seconds, or if no impulse comes from the
wheel speed sensor, the settings are automatically saved and the Setup
menu is closed.
6.15.5 Setting the clock
Condition
The motorcycle is stationary.
– Press the button briefly and repeatedly until CLK appears at the bottom right of
the display.
– Press the button for 3 - 5 seconds.
The hour display flashes.
– Set the hour display with the button and/or button .
– Press the button briefly.
The next segment of the display flashes and can be set.
– You can set the following segments in the same way as the hours by pressing
400330-01
the button and the button .
Info
The seconds can only be set to zero.
– Press the button for 3 - 5 seconds.
The settings are stored and the Setup menu is closed.
Info
If no button is pressed for 20 seconds, or if no impulse comes from the
wheel speed sensor, the settings are automatically saved and the Setup
menu is closed.
6.15.6 Adjusting the speedometer functions
Info
When the vehicle is delivered, only the SPEED/H and SPEED/ODO display modes are activated.
Condition
The motorcycle is stationary.
– Press the button briefly and repeatedly until H appears at the bottom right of the
display.
– Press the button for 3 - 5 seconds.
The Setup menu is displayed and the activated functions are shown.
– Change to the desired function by pressing the button briefly.
The selected function flashes.
Activating a function
– Press the button .
400318-01
Deactivating the function
– Press the button .
– All desired functions are activated or deactivated accordingly.
– Press the button for 3 - 5 seconds.
The symbol remains on the screen and the display changes to the next
function.
The symbol on the screen goes out and the display changes to the next
function.
The settings are stored and the Setup menu is closed.
6 CONTROLS 18
Info
If no button is pressed for 20 seconds, or if no impulse comes from the
wheel speed sensor, the settings are automatically saved and the Setup
menu is closed.
6.15.7 Querying lap time
Info
This function can be called up only if lap times are measured.
Condition
The motorcycle is stationary.
– Press the button briefly and repeatedly until LAP appears at the bottom right of
the display.
– Press the button briefly.
LAP 1 appears on the left side of the display.
– Laps 1-10 can be displayed by pressing the button .
– The button has no function.
– Press the button briefly.
Next display mode
400321-01
Info
If an impulse is received from the wheel speed sensor, the left side of the
display changes back to the SPEED mode.
6.15.8 Display mode SPEED (speed)
– Press the button briefly and repeatedly until SPEED appears on the left side of
the display.
The current speed is displayed in the SPEED display mode.
The current speed can be displayed in Km/h or Mph.
400317-02
6.15.9 Display mode SPEED/H (operating hours)
Condition
• The motorcycle is stationary.
– Press the button briefly and repeatedly until H appears at the bottom right of the
display.
In display mode H, the operating hours of the engine are displayed.
The operating hours counter stores the total traveling time.
400316-01
Info
Making the setting according to the country.
When an impulse comes from the front wheel, the left side of the speedometer
display changes to the SPEED mode and the current speed is shown.
Info
The service hour counter is necessary for ensuring that service work is carried
out at the right intervals.
If the speedometer is in H display mode at the start of the journey, it automatically changes to the ODO display mode.
The H display mode is suppressed during the journey.
Press the button . No function
Press the button . No function
Press the button
for 3 - 5 seconds.
Press the button
briefly.
The display changes to the Setup menu of the speedometer
functions.
Next display mode
6 CONTROLS 19
6.15.10 Display mode SPEED/CLK (clock)
– Press the button briefly and repeatedly until CLK appears at the bottom right of
the display.
The time is displayed in CLK display mode.
Press the button . No function
Press the button . No function
400319-01
6.15.11 Display mode SPEED/LAP (lap time)
Press the button
for 3 - 5 seconds.
Press the button
briefly.
– Press the button briefly and repeatedly until LAP appears at the bottom right of
the display.
In the LAP display mode, up to 10 lap times can be timed with the stop watch.
Info
If the lap time continues after you press the button , 9 memory locations are
already occupied.
Lap 10 must be timed with the button .
The display changes to the Setup menu of the clock.
Next display mode
400320-01
Press the button . Starts or stops the clock.
Press the button . Stops the current lap time and saves it, and the stop watch
Press the button
for 3 - 5 seconds.
Press the button
briefly.
6.15.12 Display mode SPEED/ODO (odometer)
– Press the button briefly and repeatedly until ODO appears at the bottom right of
the display.
The total distance traveled is displayed in the ODO display mode.
Press the button . No function
Press the button . No function
Press the button
for 3 - 5 seconds.
400317-01
Press the button
briefly.
6.15.13 Display mode SPEED/TR1 (trip master 1)
– Press the button briefly and repeatedly until TR1 appears at the top right of the
display.
TR1 (trip master 1) runs constantly and counts to 999.9.
You can use it to measure trips or the distance between refueling stops.
TR1 is coupled with A1 (average speed 1) and S1 (stop watch 1).
starts the next lap.
The stop watch and the lap time are reset.
Next display mode
–
Next display mode
400323-01
Info
If 999.9 is exceeded, the values of TR1, A1 and S1 are automatically reset to
0.0.
Press the button . No function
Press the button . No function
Press the button
for 3 - 5 seconds.
Press the button
briefly.
The TR1, A1 and S1 displays are reset to 0.0.
Next display mode
6 CONTROLS 20
6.15.14 Display mode SPEED/TR2 (trip master 2)
– Press the button briefly and repeatedly until TR2 appears at the top right of the
display.
TR2 (trip master 2) runs constantly and counts up to 999.9.
The displayed value can be set manually with the button and the button . This is a
very practical function when riding using the road book.
Info
The TR2 value can also be corrected manually during the journey with the button and the button .
400324-01
6.15.15 Display mode SPEED/A1 (average speed 1)
If 999.9 is exceeded, the value of TR2 is automatically reset to 0.0.
Press the button . Increases value of TR2.
Press the button . Reduces value of TR2.
Press the button
for 3 - 5 seconds.
Press the button
briefly.
– Press the button briefly and repeatedly until A1 appears at the top right of the
display.
A1 (average speed 1) shows the average speed calculated on the basis of TR1 (trip master 1) and S1 (stop watch 1).
The calculation of this value is activated by the first impulse of the wheel speed sensor
and ends 3 seconds after the last impulse.
Deletes value of TR2.
Next display mode
Press the button . No function
Press the button . No function
400325-01
Press the button
for 3 - 5 seconds.
Press the button
briefly.
6.15.16 Display mode SPEED/A2 (average speed 2)
– Press the button briefly and repeatedly until A2 appears at the top right of the
display.
A2 (average speed 2) shows the average speed on the basis of the current speed if the
stop watch S2 (stop watch 2) is running.
Info
The displayed value can differ from the actual average speed if S2 is not
stopped after the ride.
400326-01
Press the button . No function
Press the button . No function
Press the button
for 3 - 5 seconds.
Press the button
briefly.
The TR1, A1 and S1 displays are reset to 0.0.
Next display mode
–
Next display mode
6 CONTROLS 21
6.15.17 Display mode SPEED/S1 (stop watch 1)
– Press the button briefly and repeatedly until S1 appears at the top right of the
display.
S1 (stop watch 1) displays the journey time on the basis of TR1 and continues when an
impulse is received from the wheel speed sensor.
The calculation of this value starts with the first impulse of the wheel speed sensor and
ends 3 seconds after the last impulse.
Press the button . No function
Press the button . No function
400327-01
Press the button
for 3 - 5 seconds.
Press the button
briefly.
6.15.18 Display mode SPEED/S2 (stop watch 2)
– Press the button briefly and repeatedly until S2 appears at the top right of the
S2 (stop watch 2) is a manual stop watch.
If S2 is running in the background, the S2 display flashes in the speedometer display.
Press the button . Starts or stops S2.
Press the button . No function
Press the button
for 3 - 5 seconds.
400328-01
Press the button
briefly.
display.
Displays of TR1, A1 and S1 are reset to 0.0.
Next display mode
Displays of S2 and A2 are reset to 0.0.
Next display mode
6.15.19 Table of functions
Display Press the button . Press the button . Press the button for 3 -
5 seconds.
Display mode SPEED/H
(operating hours)
Display mode SPEED/CLK
(clock)
Display mode SPEED/LAP
(lap time)
Display mode
SPEED/ODO (odometer)
Display mode SPEED/TR1
(trip master 1)
Display mode SPEED/TR2
(trip master 2)
Display mode SPEED/A1
(average speed 1)
Display mode SPEED/A2
(average speed 2)
Display mode SPEED/S1
(stop watch 1)
Display mode SPEED/S2
(stop watch 2)
No function No function The display changes to
the Setup menu of the
speedometer functions.
No function No function The display changes to
the Setup menu of the
clock.
Starts or stops the
clock.
No function No function – Next display mode
No function No function The TR1, A1 and S1 dis-
Increases value of TR2. Reduces value of TR2. Deletes value of TR2. Next display mode
No function No function The TR1, A1 and S1 dis-
No function No function – Next display mode
No function No function Displays of TR1, A1 and
Starts or stops S2. No function Displays of S2 and A2
Stops the current lap
time and saves it, and
the stop watch starts
the next lap.
The stop watch and the
lap time are reset.
plays are reset to 0.0.
plays are reset to 0.0.
S1 are reset to 0.0.
are reset to 0.0.
Press the button
briefly.
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
Next display mode
6 CONTROLS 22
6.15.20 Table of conditions and menu activation
Display The motorcycle is
stationary.
Display mode SPEED/H (operating hours) •
Display mode SPEED/CLK (clock) •
Display mode SPEED/LAP (lap time) •
Display mode SPEED/TR1 (trip master 1) •
Display mode SPEED/TR2 (trip master 2) •
Display mode SPEED/A1 (average speed 1) •
Display mode SPEED/A2 (average speed 2) •
Display mode SPEED/S1 (stop watch 1) •
Display mode SPEED/S2 (stop watch 2) •
Menu can be activated
6.16 Opening filler cap
Danger
Fire hazard Fuel is highly flammable.
– Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.
– Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See the notes on refueling.
Warning
Danger of poisoning Fuel is poisonous and a health hazard.
– Avoid contact between fuel and skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immedi-
ately with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, contact a doctor immediately. Change clothing that has come into contact with fuel. Store fuel in a suitable canister according
to regulations and keep it out of the reach of children.
Warning
Environmental hazard Improper handling of fuel is a danger to the environment.
– Do not allow fuel to get into the ground water, the ground, or the sewage system.
– Press release button 1, turn filler cap counterclockwise and lift it upwards and
remove.
101305-10
6.17 Closing filler cap
– Replace the filler cap and turn clockwise until the release button 1 locks in place.
Info
Route the fuel tank breather hose 2 without kinking.
101306-10
6 CONTROLS 23
6.18 Idle speed adjusting screw
Idle speed adjusting screw 1 is located on the throttle valve body at the top left.
The idle speed adjusting screw has two functions.
Turning it controls the idle speed.
Pulling it out all the way raises the idle speed during a cold start.
Possible states
• RPM increase activated – Idle speed adjusting screw is pulled out all the way.
• RPM increase deactivated – Idle speed adjusting screw is pushed in all the way.
L00005-01
6.19 Shift lever
6.20 Kick starter
Shift lever 1 is mounted on the left side of the engine.
101437-10
The gear positions can be seen in the photograph.
The neutral or idle position is between the first and second gears.
101438-10
The kick starter 1 is fitted on the right of the engine.
The engine can be started with either the kick starter or the electric starter.
The upper part of the kick starter can be swung out.
101439-10
Info
Before riding, swing the upper part of the kick starter inwards towards the
engine.
6 CONTROLS 24
6.21 Foot brake lever
Foot brake lever 1 is located in front of the right footrest.
The foot brake lever is used to activate the rear brake.
101440-10
6.22 Side stand
The side stand 1 is on the left side of the vehicle.
101441-10
The side stand is used to park the motorcycle.
101442-10
6.23 Steering lock (All EXC‑F models)
Steering lock 1 is fitted on the left side of the steering head.
The steering lock is used to lock the steering. Steering, and therefore riding, is no
longer possible.
101313-10
Info
When you are riding, the side stand 1 must be folded up and secured with the
rubber band 2.
6.24 Locking the steering (All EXC‑F models)
Note
Danger of damage The parked vehicle may roll away or fall over.
– Always place the vehicle on a firm and even surface.
6 CONTROLS 25
– Park the vehicle.
– Turn the handlebar as far as possible to the right.
– Insert the key in the steering lock, turn it to the left, press it in and turn it to the
right. Remove the key.
Steering is no longer possible.
Info
Never leave the key in the steering lock.
400732-01
6.25 Unlocking the steering (All EXC‑F models)
– Insert the key in the steering lock, turn it to the left, pull it out and turn it to the
right. Remove the key.
You can now steer the bike again.
Info
Never leave the key in the steering lock.
400731-01
7 PREPARING FOR USE 26
7.1 Advice on first use
Danger
Danger of accidents Danger arising from the rider's judgement being impaired.
– Do not operate the vehicle while under the influence of alcohol, drugs and certain medications or physically or mentally
impaired.
Warning
Risk of injury Missing or poor protective clothing presents an increased safety risk.
– Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always
wear protective clothing that is in good condition and meets the legal requirements.
Warning
Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.
– The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.
Warning
Danger of accidents Critical riding behavior due to inappropriate riding.
– Adapt your riding speed to the road conditions and your riding ability.
Warning
Danger of accidents Accident risk caused by presence of a passenger.
– Your vehicle is not designed to carry passengers. Do not ride with a passenger.
Warning
Danger of accidents Failure of brake system.
– If the foot brake lever is not released, the brake linings drag continuously. The rear brake may fail due to overheating. Take
your foot off the foot brake lever when you are not braking.
Warning
Danger of accidents Unstable riding behavior.
– Do not exceed the maximum permissible weight and axle loads.
Warning
Risk of misappropriation Usage by unauthorized persons.
– Never leave the vehicle while the engine is running. Secure the vehicle against use by unauthorized persons.
Info
When using your motorcycle, remember that others may feel disturbed by excessive noise.
– Make sure that the pre-delivery inspection work has been carried out by an authorized KTM workshop.
You receive a delivery certificate and the service record at vehicle handover.
– Before your first trip, read the entire operating instructions carefully.
– Get to know the controls.
– Adjust the basic position of the clutch lever. ( p. 67)
(All EXC‑F models)
– Adjust the free travel of the hand brake lever. ( p. 69)
(XCF‑W)
– Adjust the basic position of the hand brake lever. ( p. 69)
–
Adjust the basic position of the foot brake lever. x ( p. 73)
–
Adjust the basic position of the shift lever. x ( p. 95)
– Get used to handling the motorcycle on a suitable piece of land before making a longer trip.
Info
Offroad, you should be accompanied by another person on another machine so that you can help each other.
– Try also to ride as slowly as possible and in a standing position to get a better feeling for the vehicle.
– Do not make any offroad trips that over-stress your ability and experience.
7 PREPARING FOR USE 27
– Hold the handlebar firmly with both hands and keep your feet on the footrests when riding.
– If you carry any baggage, make sure it is fixed firmly as close as possible to the center of the vehicle and ensure even weight dis-
tribution between the front and rear wheels.
Info
Motorcycles react sensitively to any changes of weight distribution.
– Do not exceed the overall maximum permitted weight and the axle loads.
Guideline
Maximum permissible overall weight 335 kg (739 lb.)
Maximum permissible front axle load 145 kg (320 lb.)
Maximum permissible rear axle load 190 kg (419 lb.)
– Run in the engine. ( p. 27)
7.2 Running-in the engine
– During the running-in phase, do not exceed the specified engine speed and engine performance.
Guideline
Maximum engine speed
During the first operating hour 7,000 rpm
Maximum engine performance
During the first 3 operating hours ≤ 75 %
– Avoid fully opening the throttle!
7.3 Preparing the vehicle for difficult riding conditions
Info
Use of the vehicle under difficult conditions, such as on sand or on wet and muddy surfaces, can lead to considerably more
rapid wear of components such as the drive train, brake system, or suspension components. For this reason, it may be necessary to inspect or replace parts before the next scheduled service.
– KTM recommends that you use the specified engine oil for difficult riding conditions and to increase performance.
Engine oil (SAE 10W/60) (00062010035) ( p. 114)
–
Clean the air filter and air filter box. x ( p. 57)
Info
Check the air filter approx. every 30 minutes.
–
Seal the air filter box. x ( p. 57)
– Additionally secure the rubber grip. ( p. 66)
– Check the electrical connector for humidity and corrosion and to ensure it is firmly seated.
» If humidity, corrosion or damage is found:
– Clean and dry the connector, or change it if necessary.
Difficult riding conditions are:
– Rides on dry sand. ( p. 28)
– Rides on wet sand. ( p. 28)
– Rides on wet and muddy surfaces. ( p. 29)
– Rides at high temperature and slow speed. ( p. 29)
– Riding at low temperature or in snow. ( p. 29)
7 PREPARING FOR USE 28
7.4 Preparing for rides on dry sand
– Fit a dust cover on the air filter.
Dust protection device for air filter (77206920000)
Info
See the KTM PowerParts fitting instructions.
600869-01
– Fit a sand cover on the air filter.
Sand protection device for air filter (59006022000)
Info
See the KTM PowerParts fitting instructions.
600871-01
– Clean the chain.
600868-01
7.5 Preparing for rides on wet sand
600870-01
Chain cleaner ( p. 116)
– Fit the steel sprocket.
Tip
Do not grease the chain.
– Clean the radiator fins.
– Straighten bent radiator fins carefully.
– Fit a rain cover on the air filter.
Waterproofing device for air filter (77206921000)
Info
See the KTM PowerParts fitting instructions.
– Clean the chain.
Chain cleaner ( p. 116)
– Fit the steel sprocket.
600868-01
Tip
Do not grease the chain.
– Clean the radiator fins.
– Straighten bent radiator fins carefully.
Loading...