KT&C TTR522 User Manual

FULL HD-TVI
IR LED DomE CamERa

User Manual

Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.

m236-TTR522-003

2

CONTENTS

1. NOTICES

2. FOR YOUR SAFETY

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. OVERVIEW AND FUNCTION

6. INSTALLATION

7. CONNECTION

8. DIMENSIONS

9. SPECIFICATION

10. OSD MENU STRUCTURE

11. TVI UTC (UP THE COAX)

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that

contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

CAUTION

3

1. NOTICES

This device complies with Part 15 of FCC regulations.
Operation is subject to the following two conditions:

1. This device may cause harmful interference.

2. This device may receive interference that can cause affect the operation of this
equipment.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference problems at his or her own expense.

Caution

Alteration or modications carried out without. appropriate authorization may invalidate

the user's right to operate the equipment.

1. A regulated DC12V 500mA power supply is recommended to ensure the best picture quality and stable
operation.

An unregulated power supply may cause damage to the camera.
Using an unregulated power supply will void the product warranty.

2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance
level.

If your monitor is switched to high impedance, then please adjust accordingly.

3. Do not attempt to disassemble the camera to access internal components.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may cause smear on the

picture and possible damage to the image sensor.

5. Do not remove the serial sticker for the warranty service.

4

1. NOTICES

WEEE

(Waste Electrical & Electronic Equipment)

This marking shown on the product or its remove, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,

or their local government oce, for details of where and how to safely recycle the

item.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal.

This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of

sucient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

5

2. FOR YOUR SAFETY

1) All warning and instruductions in this manual should be followed.

2) Save this manual for future reference.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliers) that produce heat.

9) To help prevent from electric shock, plug the equipment and peripheral power cables

into properly polarized or grounded electrical outlets. These cables are equipped with

the wide blade or the third prong to ensure proper grounding. Do not use adapter

plug or remove the ground prong from a cable. If the provided plug does not t your

outlet, consult an electrician.

10) Ensure that nothing rests on your equipment's cable and that the cables are not

located where they can be stpped on, trapped over, or pinched.

11) Only use attachments or accessories as specied.

12) Only use the equipment with the cart, stand, tripod, bracket, or table

that is specied by the manufacturer or sold with the apparatus. When

a cart is used, use caution to prevent the cart from tipping over and to
avoid injury.

13) Do not connect or disconnect during lighting storms due to risk of electric shock.

14) If any of the following conditions occur, unplug the equipment from the electrical

outlet and replace the part or contact your trained service provider:

• The power cable, extension cable, or plug is damaged.

• An object has fallen into the equipment.

• The equipment has been exposed to water.

• The equipment has been dropped or damaged.

• The equipment does not operate correctly when you follow the operating

instructions.

6

3. FEATURES

• High resolution

SONY 1/2.8" 2.1MP Progressive Color CMOS Image Sensor, 1080p(1920x1080)@30fps

• Support various digital video output

1080p@30fps / 1080p@25fps / 720p@30fps / 720p@25fps

• HD-TVI (HD-Transport Video Interface) Output
HD-TVI is suitable for long reach transmission over single coaxial cable.

Transmission Distance: 300 m (Color)
Max. Transmission Distance: 500 m

• Service video output for convenient installation, and ease of service.

• OSD menu for setup and configuration.

• 20 long life IR illuminators for 0 Lux viewing performance and range to 20 m (66 ft.)

• Provides True Day/Night capability with motorized IR cut filter.

• Power source: 12VDC

• 3-Axis gimbal

• IP66 Waterproof construction.

• UTC (Up the coax.) via HD-TVI coaxial cable.

7

4. EQUIPMENT AND ACCESSORIES

Camera Manual

Template Screws, Set Screw / L-Wrench / Plastic Anchors

Screws

L-Wrench

Plastic Anchors

Set Screw

8

5. CAMERA COMPONENT DESCRIPTIONS

IR LED

Housing Ball

Housing Ball
Bracket

Housing Bottom

Housing Top

Photo Cell

9

6. INSTALLATION

Plastic Anchors

(4ea)

Tapping Screws-4x25L

(4ea)

Template

L-Wrench

Set Screw-M2.5x3L

(1ea)

Open

Close

140°

70°

70°

10

7. CONNECTION

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

• MONITOR CONNECTION

BNC FEMALE

CVBS

12VDC POWER SUPPLY

12VDC IN

BNC FEMALE HD-TVI

11

8. DIMENSIONS

Unit(mm)

63

77

(The maximum rotation)

20-IR LED

Ø 93

4-Ø4.5

Ø68.5

Ø 69

12

9. SPECIFICATION

Image Device 1/2.8" Progressive Scan CMOS
Effective Pixels 1984 (H) x 1105 (V)
Unit Cell Size(um) 2.8 (H) x 2.8 (V)

Video Output Mode

HD-TVI: 1080P 30fps(25fps) / 720P 30fps(25fps)

TV Out: CVBS NTSC/PAL
Transmission Distance HD-TVI: Color 300m@RG59, BW 500m@RG59
Minimum Illumination 0 Lux (wih IR LED On)

Shutter Speed

Auto / Manual selectable

1/30(25), 1/60(50), 1/120(100), 1/250, 1/700,

1/1000, 1/1600, 1/2500, 1/5000, 1/7000, 1/10000, 1/30000

OSD Built in

WDR/BLC Off / WDR / BLC Selectable

AGC 0 - 42 dB
3DNR Off / Low / Middle / High / Auto
Digital Zoom Ratio 1x - 8x
Digital Slow Shutter Off - 16x
White Balance Auto / Push Lock / Manual
Lens Board Lens
IR LED 850nm, 20 ea, up to 20 m (65.6 ft.)
IP Rating IP66

Temperature

Operation: 14°F~122°F(-10°C~+50°C)

Storage: -4°F~140°F(-20°C~+60°C)

Power Consumption 12VDC(±10%), Max. 400mA
Dimension(mm) Ø93 X 63
Weight Approx. 332 g (0.73 lbs)

*Specifications and designs are subject to change for improving the

functionality of this product without notice.

13

10. OSD MENU STRUCTURE

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu 4th Sub Menu

EXPOSURE

BRIGHTNESS 0 - 20

SHUTTER MODE

AUTO / FLICKER
/ MANUAL

SHUTTER SPEED

1/25(30), 1/50(60),
1/100(120), 1/240, 1/500,
1/1000, 1/2000, 1/4000,
1/8000, 1/16000, 1/30000

DSS OFF, X2 - X16

AGC MAX OFF, 2dB - 42 dB
INITIAL
RETURN

WHITE BALANCE

MODE

AUTO / PUSH LOCK

/ MANUAL
PUSH AUTO PUSH
CHROMA 0 - 20
RED GAIN 0 - 20
BLUE GAIN 0 - 20
INITIAL
RETURN

WDR/BLC

MODE

OFF / BLC / HLC / WDR

LEVEL 0 - 10
BLC POSITION [˩]
BLC SIZE [˩]
HLC COLOR

BLACK / D.GRAY / L. GRAY
INITIAL
RETURN

DAY&NIGHT

MODE AUTO / COLOR / BW

DWELL TIME 0 - 20 s

DAY → NIGHT 1 - 10

NIGHT → DAY 1 - 10
NIGHT COLOR BW / COLOR
TVI BURST

ON / OFF
IR SMART

OFF / LOW / MID / HIGH

INITIAL
RETURN

*IR SMART Feature:

IR SMART feature only works at B/W mode.

IR Smart feature adjusts AE LEVEL to prevent a subject being too bright by the saturation of light.

14

10. OSD MENU STRUCTURE

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu 4th Sub Menu

IMAGE

SHARPNESS 0 - 10

DZOOM 1.0X - 8.0X

GAMMA

0.45 / 0.5 / 0.55 / 0.6

/ 0.65

FLIP

OFF / H-FLIP / V-FLIP

/ HV-FLIP

DNR

OFF / LOW / MID / HIGH /

AUTO

DEFOG OFF / LOW / MID / HIGH

SHADING OFF / LOW / MID / HIGH

INITIAL

RETURN

SPECIAL

CAM TITLE

TITLE : ________________

A B C D E F G H I J K L M N O P←

Q R S T U V W X Y Z [ ] ^ _ " →

■ ! # $ % & ' ( ) * + , - . / SP

0 1 2 3 4 5 6 7 8 9 : ; < = > ? BS

DISPLAY OFF / ON

POSITION [ ˩ ]

RETURN

PRIVACY

OFF

ON

ZONE NUMBER 1 - 8

MODE OFF / ON

ZONE POSITION [ ˩ ]

ZONE SIZE [ ˩ ]

ZONE COLOR

BLACK / WHITE / YELLOW

/ CYAN / GREEN /
MAGENTA / RED / BLUE

TRANSPARENCY 0 - 7

INITIAL

RETURN

15

10. OSD MENU STRUCTURE

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu 4th Sub Menu

SPECIAL

MOTION

OFF

ON

SENSITIVITY LOW / MID / HIGH

DISPLAY MARK / AREA

INITIAL

RETURN

SYSTEM

LANGUAGE

ENGLISH / RUSSIAN / SPANISH / GERMAN / FRENCH /
PORTUGUESE / JAPANESE

DEFECT [ ˩ ]

FRAME RATE

1080p - NTSC / 1080p - PAL
/ 720p - NTSC / 720p - PAL

APPLY [ ˩ ]

RETURN

INITIAL

RETURN

FACTORY DEF.

EXIT

*Important Note:

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.

Else all changes will be discarded.

16

11. TVI UTC (UP THE COAX)

The UTC function supports OSD control via HD-TVI coaxial cable.
PELCO-C Protocol is used.

* DVR setting method. (DVR maker: HIKVISION)

STEP-1

- Enter HIKVISION DVR menu.

- Select "Camera" icon.

STEP-2

- Select "PTZ" item.

- Select "PTZ setting" icon.

STEP-3

- Select "PELCO-C (Coaxitron)"

STEP-4

- Exit menu.

- Please click the right mouse button.

- Select "PTZ control"

STEP-5

- Now control the PTZ panel.

- Iris+: SET key

- Use Up/Down/Left/Right