Thank you for selecting this KT&C Omni IP Series product. For additional
information please refer to the complete User Guide for this cameras series. End users
should contact their KT&C Certified Dealer for service. Certified Dealers can obtain
support directly from KT&C.
About This Guide
While KT&C makes every effort to insure the completeness and accuracy of the
information contained in this Guide, we are not responsible for typographical errors or
misprints. At the same time, KT&C reserves the right to make changes to improve the
performance of our products at any time without notice, and so the specifications and
content of this document are subject to change without notice. Every effort will be
made to include updates in new versions of this manual and/or online.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability
of the security or signaling aspects of this product. UL has only tested for fire, shock
or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the security or signaling
aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR
RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.”
1
User Manual for OMNI-IP Network Cameras
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to
a designated collection point. For more information see:
www.recyclethis.info.
2
User Manual for OMNI-IP Network Cameras
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Safety Instructions
These instructions are intended to ensure that the camera is installed in a manner that
avoids danger to persons or property loss.
These precautionary measures are divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment/property damage may occur if any of the cautions are neglected.
Warnings:
In the use of the product, you must be in strict compliance with the electrical
safety regulations of the nation and region. Please refer to technical specifications
for detailed information.
Input voltage should meet the requirements for both the SELV (Safety Extra Low
Voltage) and Limited Power Source for 12 VDC according to the IEC60950-1
standard; or 802.3af PoE. Please refer to technical specifications for detailed
information.
If connecting several devices to one power supply, to avoid any overload that may
cause over-heating or a fire hazard insure that the power supply is adequate for the
power load.
Please make sure that all plugs are firmly connected to the power sockets. When
the product is mounted on wall or ceiling, the device shall be firmly attached,
taking into consideration any wind, snow loading, or other factors. The mounting
surface shall be capable of supporting several times the base weight of the camera.
If smoke, unusual odors or noise come from the device, turn off the power at once
and unplug the power cable, and then contact authorized service personnel.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
To reduce the risk of fire or electrical shock, do not expose this product to rain or
3
User Manual for OMNI-IP Network Cameras
moisture beyond the IP66 rating of applicable products.
Installation should be performed only by qualified service personnel and should
conform to all local codes.
Please install appropriate overload protection in the power supply circuits for any
necessary power supply interruption.
Please make sure that the wall/ceiling can support more than three times the
weight of the camera (and any other forces such as wind or snow loading) if the
camera is mounted to a wall/ceiling.
Cautions:
Make sure the power supply/PoE voltage is correct before using the camera.
Do not drop the camera or subject it to physical shock.
Do not touch lenses or sensor modules with fingers. If cleaning is necessary,
use clean cloth with a bit of ethanol and wipe gently. If the camera will not be
used for an extended period, please protect the lens openings from damage
and/or debris.
Avoid aiming the camera at the sun or extremely bright light sources.
Blooming or smearing may occur in excessive light (which is not a
malfunction), and could compromise the performance of the sensor.
The sensor may be damaged if exposed to laser energy, so when any laser
equipment is in use, make sure that the sensor will not be exposed to the laser
beam.
Do not place the camera in extremely hot or cold (see camera specifications)
locations. Do not exceed the rated environmental (IP66) conditions. Do not
expose the camera to high levels of electromagnetic (RF) radiation.
To avoid heat accumulation, good ventilation is required in the operating
environment.
Keep the camera away from solvents while in use; exposure to liquids should
not exceed IP66 environmental conditions.
During shipping, the camera shall be packed in its original packing, or packing
providing the equivalent protection.
Improper use or replacement of any batteries (if so equipped) may result in the
hazard of explosion. Replace with the same or equivalent type only. Dispose
of used batteries according to the instructions provided by the battery
manufacturer.
If the product does not function properly, Dealers please contact KT&C; End
Users please contact your KT&C Certified Dealer or an authorized service
center. Do not disassemble the camera for repair or maintenance by yourself.
(KT&C shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.)
4
User Manual for OMNI-IP Network Cameras
Table of Contents
Chapter 1 System Requirements .............................................................................. 7
Appendix 2 Port Mapping ................................................................................................ 93
Chapter 1 System Requirements
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Safari 5.02 and above
version, Mozilla Firefox 3.5 and above version and Google Chrome 8 and above
versions.
7
User Manual for OMNI-IP Network Cameras
Chapter 2 Network Connection
Before you start:
If you want to set the network camera via a LAN (Local Area Network), please refer to Section 2.1
Setting the Network Camera over the LAN.
If you want to set the network camera via a WAN (Wide Area Network), please refer to Section 2.2
Setting the Network Camera over the WAN.
If you will use the IPC in Plug-and-Play mode, the IP configuration should be controlled by/be
compatible with the NVR camera network settings. See the NVR documentation for more information.
2.1 Setting the Network Camera over the LAN
Purpose:
To view and configure the camera via a LAN, you need to connect the network camera in the same subnet
with your computer, and install the OMNI Finder or OMNI CMS software to search and change the IP of the
network camera.
Note:For a detailed description of OMNI Finder, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways to connect a network camera to a computer. Camera power may be
supplied from an external 12VDC supply, PoE switch or PoE swtich or injector (not shown in these network
diagrams).
Purpose:
To test the network camera, you can connect the network camera directly to a computer with a network
cable as shown in Figure 2-1 (external 12VDC power or PoE injector required).
Refer to the Figure 2-2 to connect the network camera over a LAN via a switch or a router. When using
a router during initial connection, the IPC and PC should be on the same LAN segment (on the ‘switch side’ of the router).
8
User Manual for OMNI-IP Network Cameras
Figure 2-1 Direct Connection
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Detecting and Changing the IP Address
You need to know the camera’s IP address to access the network camera.
Steps:
1. To get the IP address, you can choose either of the following methods:
Use OMNI Finder, a software tool which can automatically detect active network cameras on a
LAN and list the device information including IP address, subnet mask, port number, device serial
number, device version, etc., shown in Figure 2-3; the IP address settings can also be set/changed
using OMNI Finder.
Use the OMNI CMS software to list/change settings for the detected devices. Please refer to the
user manual for OMNI CMS software for detailed information.
2. Change the IP address and subnet mask to the same subnet as that of your computer, or change your
computer to match the address/subnet of the camera.
3. Enter the IP address of network camera in the address field of the web browser to view the live video.
Notes:
The default configuration is a static IP address of 192.0.0.64; the web port number is 80; RTSP
defaults to port 554, and the ‘control’ port used by OMNI CMS, OMNI Finder and other functions is
9
User Manual for OMNI-IP Network Cameras
8000. The default user name is admin, and password is 12345.
For accessing the network camera from different subnets, please set the gateway for the network camera,
either after you logged in or though the “modify Network Parameters” applet. For more detailed
information, please refer to Section 6.3.1 Configuring TCP/IP Settings.
Figure 2-3 OMNI Finder Interface
2.2 Accessing a Network Camera over a WAN
Purpose:
This section explains how to connect a network camera to a WAN with a static WAN IP or a dynamic WAN
IP.
2.2.1 Static IP Connection
Before you start:
Please find out the static IP from your ISP (Internet Service Provider). With a static IP address, you can
connect the network camera via a router (with that static IP address set on the WAN side of the router) or
you can set WAN static IP in the camera and connect the camera directly to the WAN.
Connecting the network camera to a WAN via a router
10
User Manual for OMNI-IP Network Cameras
Steps:
1. Connect the network camera to LAN side of the router.
2. Assign a LAN IP address, the subnet mask and the gateway, consistent with the router LAN settings. The
gateway address is the LAN IP address of the router. Refer to Section 2.1.2Detecting and Changing the IP Address for discussion of detailed IP address configuration of the camera.
3. Program the static IP (entire configuration: IP, subnet, gateway and DNS settings) into the WAN settings
for the router.
4. Set port mapping (or forwarding), for the camera ports (e.g., 80, 8000, and 554), so that you may access
these camera ports through the router. The steps for port mapping vary according to the different routers.
Please call the router manufacturer for assistance with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Connect to the network camera over the internet using a web browser or the OMNI CMS client software.
Figure 2-4 Accessing the Camera through Router with Static IP
Connecting the network camera directly to the Internet using a static IP
You can also save the static IP in the camera and connect it directly to the Internet without using a router.
Refer to Section 2.1.2 Detecting and Changing the IP Address for detailed IP address configuration of the
camera.
Figure 2-5 Accessing the Camera with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please obtain a dynamic IP from an ISP. With a dynamic IP address, you can access the network camera
11
User Manual for OMNI-IP Network Cameras
through a modem or a router.
Connecting the network camera via a router
Steps:
1. Connect the network camera to the router.
2. In the camera, assign a static LAN IP address, the subnet mask and the gateway. Setting a DNS server
address is highly recommended (and required to be able to use DDNS). Refer to Section 2.1.2Detecting and Changing the IP Address for detailed LAN configuration.
3. Confirm that the router is connected to the ISP and has received a WAN IP address.
4. Set port mapping. E.g. for ports 80, 8000, and 554 ports. The steps for port mapping vary depending on
different routers. Please call the router manufacturer for assistance with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Create a DDNS name from a DDNS provider. It may be necessary to create an account with the provider.
Using a DDNS name, you can reliably and consistently connect to a device (camera or DVR or NVR)
even if the dynamic WAN IP address issued by the ISP changes.
6. Configure the DDNS settings in the setting interface of the router or camera.
7. Access the camera via the DDNS name (and port, if needed).
Connecting the network camera via a DSL modem connection requiring login authentication
Purpose:
This camera supports the PPPoE function. The camera gets a public IP address from a DSL connection after
the camera is connected to a DSL modem and authenticated on the network. You need to configure the
PPPoE parameters in the network camera. Refer to Section 5.3.3 Configuring PPPoE Settings for detailed
configuration.
Figure 2-6 Accessing the Camera with DSL/Dynamic IP
Note:The IP address is dynamically assigned via PPPoE, so the IP address often changes after rebooting the
camera. To solve the inconvenience of having a dynamic IP, use a DDNS domain name from a DDNS
12
User Manual for OMNI-IP Network Cameras
provider (e.g. SimpleDDNS.com). Please follow the steps below for normal domain name resolution and
private domain name resolution to address the DHCP problem.
Normal Domain Name Resolution
Figure 2-7 Normal Domain Name Resolution
Steps:
1. Obtain a DDNS name from a DDNS service provider.
2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section
6.3.4 Configuring DDNS Settings for detailed configuration.
3. Access the camera via the pre-defined domain name.
Private Domain Name Resolution
Figure 2-8 Private Domain Name Resolution
Steps:
1. Install and run IP Server software in a computer with a static IP.
2. Access the network camera through the LAN with a web browser or the client software.
3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4Configuring DDNS
Settings for detailed configuration.
13
User Manual for OMNI-IP Network Cameras
Chapter 3 Web Access to the
Network Camera
3.1 Web Browser Access
System Requirements:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above
version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network camera, e.g.,
192.0.0.64 and press the Enter key to display the login interface.
3. Input the user name and password.
4. Click Login.
Figure 3-1 Login Interface
5. Install the plug-in before viewing the live video and managing the camera. Please
follow the installation prompts to install the plug-in.
It is recommended to close the web browser before finishing the installation of the
plug-in.
14
User Manual for OMNI-IP Network Cameras
Figure 3-2 Download Plug-in
Figure 3-3 Install Plug-in (1)
Figure 3-4 Install Plug-in (2)
6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to
login.
3.2 Accessing by OMNI CMS Software
3.2.1 Accessing by CMS
The product CD contains OMNI CMS. You can view the live video and manage the
camera with the software.
15
User Manual for OMNI-IP Network Cameras
Follow the installation prompts to install the software. The control panel and live view
interface of CMS are shown as below.
Figure 3-5 CMS Control Panel
Figure 3-6 CMS Live View Interface
Note: For detailed information about the software, please refer to the user manual for
16
User Manual for OMNI-IP Network Cameras
OMNI CMS.
3.2.2 Accessing by OMNI Remote Software
To view the camera with a mobile phone, you can just install the OMNI Remote
software in your iOS or Android mobile phone. The software can be found in the App
Store and Google Play.
Note: For detailed information about OMNI Remote software, please refer to the user
manual for OMNI Remote.
17
User Manual for OMNI-IP Network Cameras
Chapter 4 Web Live View
4.1 Live View Page
Purpose:
The live view page allows you to view the real-time video, capture images, realize
PTZ control, set/call presets and configure video parameters.
Log in the network camera to enter the live view page, or you can click Live View on
the menu bar of the main page to enter the live view page.
Sections of the live view tab page:
Figure 4-1 Live View Page
Menu Bar:
Click each tab to enter Live View, Playback, Log and Configuration page
respectively.
Display Control:
Click each tab to adjust the layout and the stream type of the live view. And you can
click the drop-down to select the plug-in. When using IE (internet explorer),
webcomponents and quick time are selectable; for other browsers, webcomponents,
quick time, VLC or MJPEG is selectable if they are supported by the web browser.
Live View Window:
Display the live video.
18
User Manual for OMNI-IP Network Cameras
Icon
Description
/
Start/Stop live view.
The window size is 4:3.
The window size is 16:9.
The original widow size.
Self-adaptive window size.
Live view with the main stream.
Live view with the sub stream.
Live view with the third stream.
Click to select the third-party plug-in.
Manually capture the picture.
/
Manually start/stop recording.
/
Audio on and adjust volume /Mute.
/
Turn on/off microphone.
/
Turn on/off 3D zooming function.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio on/off,
two-way audio, etc.
PTZ Control:
Panning, tilting and zooming actions of the camera and the lighter and wiper control
(if it supports PTZ function or an external pan/tilt unit has been installed).
Preset Setting/Calling:
Set and call the preset for the camera (if supports PTZ function or an external pan/tilt
unit has been installed).
4.2 Starting Live View
In the live view tab as shown in Figure 5-2, click on the toolbar to start the live
view of the camera.
Figure 4-2 Live View Toolbar
Table 4-1 Descriptions of the Toolbar
19
User Manual for OMNI-IP Network Cameras
4.3 Recording and Capturing Pictures Manually
In the live view interface, click on the toolbar to capture the live pictures or
click to record the live view. The saving paths of the captured pictures and clips
can be set on the Configuration > Local Configuration page. To configure remote
scheduled recording, please refer to Section 7.2.
Note: The captured image will be saved as JPEG file or BMP file in your computer.
4.4 Operating PTZ Control
Purpose:
In the live view interface, you can use the PTZ control buttons to exercise
pan/tilt/zoom control of cameras so equipped.
Before you start:
To achieve PTZ control, the camera connected to the network must support the PTZ
function or a pan/tilt unit has been installed to the camera.
4.4.1 PTZ Control Panel
On the live view page, click to show the PTZ control panel or click to
hide it.
Click the direction buttons to control the pan/tilt movements.
Figure 4-3 PTZ Control Panel
Click the zoom/iris/focus buttons to realize lens control.
Notes:
There are 8 direction arrows ( , ,, ,,,,) in the live view window
when you click and drag the mouse in the relative positions.
20
User Manual for OMNI-IP Network Cameras
Icon
Description
Zoom in/out
Focus near/far
Iris +/-
Light on/off
Wiper on/off
One-touch focus
Initialize lens
Adjust speed of pan/tilt movements
For the cameras which support lens movements only, the direction buttons are
invalid.
Table 4-2 Descriptions of PTZ Control Panel
4.4.2 Setting / Calling a Preset
Setting a Preset:
1. In the PTZ control panel, select a preset number from the preset list.
Figure 4-4 Setting a Preset
2. Use the PTZ control buttons to move the lens to the desired position.
• Pan the camera to the right or left.
• Tilt the camera up or down.
• Zoom in or out.
• Refocus the lens.
3. Click to finish the setting of the current preset.
4. You can click to delete the preset.
Note: You can configure up to 128 presets.
21
User Manual for OMNI-IP Network Cameras
Calling a Preset:
This feature enables the camera to point to a specified preset scene manually or when
an event takes place.
For the defined preset, you can call it at any time to the desired preset scene.
In the PTZ control panel, select a defined preset from the list and click to call the
preset.
Or you can place the mouse on the presets interface, and call the preset by typing the
preset No. to call the corresponding presets.
Figure 4-5 Calling a Preset
22
User Manual for OMNI-IP Network Cameras
Chapter 5 Network Camera
Configuration
5.1 Configuring Local Parameters
Note: The local configuration refers to the parameters of the live view, record files
and captured pictures. The record files and captured pictures are the ones you record
and captured using the web browser and thus the file paths for these are on the PC
running the browser (or other folders available to the PC).
Steps:
1. Enter the Local Configuration interface:
Configuration > Local Configuration
Figure 5-1 Local Configuration Interface
2. Configure the following settings:
Live View Parameters: Set the protocol type and live view performance.
Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.
TCP: Ensures complete delivery of streaming data and better video quality,
yet the real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
HTTP: Allows the same quality as of TCP without setting specific ports for
23
User Manual for OMNI-IP Network Cameras
streaming under some network environments.
MULTICAST: It’s recommended to select MCAST type when using the
Multicast function. For detailed information about Multicast, refer to Section
6.3.1 TCP/IP Settings.
Live View Performance: Set the live view performance to Shortest Delay,
Real Time, Balanced or Best Fluency.
Rules: It refers to the rules on your local browser, select enable or disable to
display or not display the colored marks when the motion detection is
triggered.
Image Format: Choose the image format for picture capture.
Record File Settings: Set the saving path of the recorded video files. Valid for the
record files you recorded with the web browser.
Record File Size: Select the packed size of the manually recorded and
downloaded video files to 256M, 512M or 1G. After the selection, the
maximum record file size is the value you selected.
Save record files to: Set the saving path for the manually recorded video files.
Save downloaded files to: Set the saving path for the downloaded video files
in playback mode.
Picture and Clip Settings: Set the saving paths of the captured pictures and
clipped video files. Valid for the pictures you captured with the web browser.
Save snapshots in live view to: Set the saving path of the manually captured
pictures in live view mode.
Save snapshots when playback to: Set the saving path of the captured
pictures in playback mode.
Save clips to: Set the saving path of the clipped video files in playback mode.
Note: You can click Browse to change the directory for saving the clips and pictures.
3. Click Save to save the settings.
24
User Manual for OMNI-IP Network Cameras
5.2 Configuring Time Settings
Purpose:
You can follow the instructions in this section to configure the time synchronization
and DST settings.
Steps:
1. Enter the Time Settings interface:
Configuration > Basic Configuration > System > Time Settings
Or Configuration > Advanced Configuration > System > Time Settings
Figure 5-2 Time Settings
Select the Time Zone.
Select the Time Zone of your location from the drop-down menu.
Synchronizing Time by NTP Server.
(1) Check the checkbox to enable the NTP function.
(2) Configure the following settings:
Server Address: IP address of NTP server.
NTP Port: Port of NTP server.
Interval: The time interval between the two synchronizing actions with NTP
server.
25
User Manual for OMNI-IP Network Cameras
Figure 5-3 Time Sync by NTP Server
Note: If the camera is connected to a public network, you should use a NTP server
that has a time synchronization function, such as the server at the National Time
Center (IP Address: 210.72.145.44). If the camera is set in a customized network,
NTP software can be used to establish a NTP server for time synchronization.
Synchronizing Time Synchronization Manually
Enable the Manual Time Sync function and then click to set the system time
from the pop-up calendar.
Note: You can also check the Sync with computer time checkbox to synchronize the
time of the camera with that of your computer.
Figure 5-4 Time Sync Manually
Click the DST tab page to enable the DST function and Set the date of the DST
period.
Figure 5-5 DST Settings
2. Click Save to save the settings.
26
User Manual for OMNI-IP Network Cameras
5.3 Configuring Network Settings
5.3.1 Configuring TCP/IP Settings
Purpose:
TCP/IP settings must be properly configured before you operate the camera over
network. The camera supports both the IPv4 and IPv6. Both versions may be
configured simultaneously without conflicting to each other, and at least one IP
version should be configured.
Or Configuration > Advanced Configuration > Network > TCP/IP
Figure 5-6 TCP/IP Settings
2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6
Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings
and Multicast Address.
27
User Manual for OMNI-IP Network Cameras
Notes:
The valid value range of MTU is 500 ~ 1500.
The Multicast sends a stream to the multicast group address and allows multiple
clients to acquire the stream at the same time by requesting a copy from the
multicast group address. Before utilizing this function, you have to enable the
Multicast function of your router.
3. Click Save to save the above settings.
Note: A reboot is required for the settings to take effect.
5.3.2 Configuring Port Settings
Purpose:
You can set the port No. of the camera, e.g. HTTP port, RTSP port and HTTPS port.
Steps:
1. Enter the Port Settings interface:
Configuration > Basic Configuration > Network > Port
Or Configuration > Advanced Configuration > Network > Port
Figure 5-7 Port Settings
2. Set theHTTP port, RTSP port and HTTPS port of the camera.
HTTP Port: The default port number is 80, and it can be changed to any port No.
which is not occupied.
RTSP Port: The default port number is 554 and it can be changed to any port No.
ranges from 1024 to 65535.
HTTPS Port: The default port number is 443, and can be changed to any port No.
28
Loading...
+ 66 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.