KT&C KNC-HDi47 User Manual

M175-HDi47-001
Megapixel Network Camera
KNC-HDi47 Installation Guide
Table of Contents
1. INTRODUCTION
2. PACKAGE CONTENTS
3. PRODUCT DESCRIPTION
4. HARDWARE INSTALLATION
5. IP ADDRESS ASSIGNMENT
6. PRODUCT SPECIFICATIONS
1. Introduction
IP Dome Camera Installation Guide
This installation guide provides instructions for installing the Network Camera on your network. For all other aspects of using the product, please see the User’s Manual, available on the CD included in this package.
Installation Steps
1. Check the package contents against the list below.
2. Read the Product description.
3. Install the hardware.
4. Set an IP address.
5. Set the admin and user ID and password. (see User’s Manual)
Important! : This product must be used in compliance with local laws and regulations.
3. Product Description
Description and Function
Board Lens Type Pinhole Lens Type
SERVICE
VIDEO OUT
Micro SD
Reset
NTSC
PA L
1. Reset Button – Press the reset switch for more than 10 seconds, the restore the camera to the function default settings.
2. Service Video Connector – Outputs video to the monitor.
3. Status LED
4. MIC Hole
6. NTSC / PAL slide Switch.
7. Power Input(DC12V) – Connects to DC 12V power.
8. Network Connector –
The Network Camera connects to the network via a standard network cable, and automatically detects the speed of the local network segment (10BaseT/100BaseTX Ethernet). PoE Supported
Micro SD
Reset
SERVICE
VIDEO OUT
NTSC
PA L
2. Package Contents
Network Camera Mounting Bracket PoE B'D Cable
Software CD Video Output Test Cable Installation Guide Screws
* Option
4. Hardware Installation
IP camera are designed to be installed using a template as shown below.
Camera Mounting Position
Connection
1. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via the network cable (PoE)
2. Connect DC 12V to the power terminal. This is not necessary if the Network Camera is connected to a PoE hub or midspan.
3. Check that the indicator LEDs indicates the correct conditions.
4. Connect the analog monitor to the service video connector for adjusting focus, then press and quickly release the reset switch for focus assistant mode. Then you can select normal view or focus view mode using the reset switch.
Caution: When you use focus assistant mode, “Focus View” mode is recommended for more exact focus. Caution: Focus assistant mode will be automatically exited after 3 minutes for normal operation.
Tapping Screw:
ø3 x 8(2ea)
Machine Screw: M2.6 x 3.5(2ea)
CAUTION !
Please start installing
in the order shown.
5. IP Address Assignment
To make it accessible on the network, the Network Camera must be assigned an IP address.
Note:
• A network DHCP server is optional.
• The Network Camera has the default IP address 192.168.0.123.
• If IP assignment fails, check that there is no firewall blocking its operation and check that the Network
Camera and your computer's IP are located on the same subnet.
Assign an IP address using IP Installer
The IP installer automatically searches for and displays network devices on your network. The application can also be used to manually assign a static IP address.
Note:
The computer running the IP installer must be on the same network segment (physical subnet) as the Network Camera.
1. Check that the Network Camera is connected to the network and that power has been supplied.
2. Start NetCAM installer.
3. When the Network Camera is displayed as shown above, select the unit that needs to be assigned an IP.
A. Refresh Device List – Rescan local network to nd the Network Camera.
B. Authenticate – Enter the administrator ID and password.
* Default User ID and Password is [ID: admin, Password: admin]
C. Host Name – Enter the Host Name of the Network Camera. D. IP Settings
i. Dynamic – Assign a dynamic IP address automatically from the DHCP server on your network. ii. Static – Assign a static IP address manually. iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80. Alternatively,
any port in the range 1024-65535 may be used, but check rst with your
system administrator before changing the default setting. E. Network Settings i. Subnet Mask – Specify the mask for the subnet the Network Camera is located on. ii. Gateway – Specify the IP address of the default router (gateway) used for connecting devices attached to different networks and network segments. iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the translation of host names to IP addresses on your network. iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the primary DNS server is unavailable.
4. Click the “Set” button to save the conguration.
Accessing the Network Camera
1. Start your browser(when you rst run ActiveX to install, run an “IE as Administrator” on Windows or Vista).
2. Enter the IP address or host name of the
Network Camera in the Address eld of your browser.
4. Click the warning message and select “Install ActiveX Control…”.
3. If you are accessing the Network Camera for the rst time, you will
see the following warning message as shown below.
7. After installing the Web View ActiveX Control, a Login page will be displayed. Enter the user ID and password.
Note: Default User ID and Password is [ID: admin, Password: admin]
6. Product Specications
ITEM DESCRIPTION
Image Device 2.1 Mega Pixel 1/3” SONY Progressive CMOS
Lens(Unit: mm) Board Lens, Pinhole Lens
Minimum Illumination 0.1 lux
Video Codec H.264 Main Prole Motion JPEG
Resolutions (H.264/MJPEG) H.264: MAX 1920x1080 + Analog Output @ 30fps, MJPEG: MAX 1280x720 @30fps
Video
Audio /
Micro SD
Network
General
Dimensions(Unit:mm)
Video Streaming Multi Streaming VBR / CRB (Controllable Frame Rate and Bandwidth)
Image Settings
Brightness, Contrast, Saturation, Sharpness, White Balance,Motion Detection, Mirror
Exposure Control, Compensation, Privacy mask, BLC, 3D DNR, D-WDR Audio Code G. 711, G.726 Audio Input Built in microphone
Micro SD / SDHC Micro Card (Max 32GB)
Security Multiple user access levels with password protection, HTTPS (SSL)
Supported Protocols
Power DC12V(±10%), Max. 240mA/ Power over Ethernet Class 3 (IEEE 802.3af)
Interfaces
Operating Conditions Temperature: - 10°C ~ +50°C(14°F~122°F), Humidity MAX. 80% RH(non-condensing)
Storage Conditions Temperature: - 20°C ~ +60°C(-4°F~140°F), Humidity MAX. 90% RH(non-condensing)
Conformity CE, FCC
Board Lens type
IPv4, HTTP, HTTPS, TCP, RTSP, RTP, UDP, IGMP, RTCP,
SMTP, FTP, ICMP, DHCP, ARP, DNS, DDNS, HTTPS, UPnP
RJ-45 for Ethernet 10baseT/100baseTX with PoE
3.5mm Power Input: DC 12V, connector for Service Video
SD Card Socket, NTSC / PAL Toggle Switch
51.6
8. The video image displays in your browser.
Note: To view streaming video in Microsoft Internet Explorer, you must set your browser to allow the “Web Viewer” to be installed on your computer. This ActiveX component is installed the first time a video stream is accessed.
Ø14
Approx. 38
28.3
Micro SD
Reset
47.5
47.5
5.5
SERVICE
VIDEO OUT
NTSC
PA L
5. Click “Install” to install the Web Viewer. 6. If a Windows Security Alert pop-up appears, click “Unblo
ck”.
Pinhole Lens type
51.6
47.5
47.5
Ø2.8
Approx. 28.3
28.3
Micro SD
Reset
5.5
SERVICE
VIDEO OUT
NTSC
PA L
Loading...