Krups Slice/IT 213 A Instruction Book/warranty

Instruction Book/Warranty/Kl?UPS Guarantee of Performance
SLICE/IT, Model # 213 A
electric fold up food slicer
IMPORTANTSAFEGUARDS
When using electrical appliances, basic safety precautions should always be observed, including the following:
Read all instructions and information in this instruction book and any other
literature
included in this carton referring to this
product
before
operating or using this appliance. To protect against risk of electrical shock do not put
slicing
unit in
water or other liquid. Close supervision is necessary when any appliance is used by or near
children. Unplug
from
outlet when not in use, before putting on or taking off
parts, and
before
cleaning.
Avoid contacting moving parts. Never feed food by hand. Always use completely assembled slicer with food platform and food grip.
Platform and sliding carriage must always be used. Hand protector must be used when food can fit onto carriage.
Once the food is only a couple of inches thick you must install the
hand protector. Do not slice frozen food.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner. Return appliance to the nearest authorized
sewice
facilii
for examination, repair or electrical or mechanical adjustment. The use of attachments not recommended or sold by the appliance
manufacturer may cause fire, electrical shock or injury.
Do not use outdoors.
Do not let cord hang over edge of table or counter. Do not let
cord
contact hot surface, including the stove.
Remove blade from slicer before washing. Blade is sharp; handle
carefully when cleaning. Always handle blade with hand away from
cutting edge and store blade with cutting edge away from you.
The
slicer is only designed for home-use and not commercial applica-
tions. Do not use appliance for other than intended use. Any
senricing
other than cleaning and user maintenance should be
performed by an authorized representative.
SAVETHESE INSTRUCTIONS
b
--a
d
a) slice thickness selector b) safety push button c) starter button d) stainless steel cutting blade
(caution: extremely sharp) e) face plate
f)
slicing table g) food slide h) end piece holder i) cord storage
4
I
.
a
131
Chlltii:
0
Blade is extremely sharp. Keep hands and fingers away from the cutting edge
of the blade at all times.
l
Operate the safety push
button with the thumb of
your right hand only.
0
Operate slicer only if blade, face plate, slicing
table, and food slide are
propedy
assembled.
0
Make sure that fingers of
your left hand stay away fromthecuttingedgeof the blade.
0
Keep slicer away from
children.
@Donotusethefoodsli-
cer for cutting frozen food.
Preparing the food slicer (pictures 0 through
@)
Assemble the appliance as
shown in the main picture. Unwind enough cord from
the cord storage compart-
ment underneath so that the slicer can be plugged in conveniently after it is set up. Make sure that the cord is guided properly through
the small opening slot on the base of the slicer as
shown in the main picture. Make sure that the slicer
sits on a flat and even sur­face.
Unfold the slicing table as
shown in figure
0.
Unfold the food slide and push down the vertical part so that it engages firmly (see figure 0) (for storage purposes only: first pull up the vertical part, then fold down). Engage the food slide with the sliding table as shown in figure 0 and lower the food slide onto the slicing table. Make sure that the tongue of the food slide inserts properly into the grove between the slicer and the sliding table. Place a plate on the other side of the food slicer (see figure 0) to catch the cut food.
Setting the Cutting Thickness (see figure
0)
Select the desired cutting thickness by turning the slice thickness selector wheel.The numbers (from 1 to 8) on the top of the face plate indicate the actual setting and serve as memory. Each number cor­responds to approximately 2 mm
(l/12
of an inch). When you have finished slicing always turn the thickness selector wheel anti-clockwise so that the dots to the right of the set­ting 1 are clearly
visible.This
way the face blade extends over the cutting blade. If you turn the slice thickness selector further anti-clock­wise the face plate can come out.
Siii
Plug in appliance and place food on the food slide (see fig.
0). Arst
press the starter
button and keep depressed. Then push the safety push
I
button
down.After
both but­tons have been pressed one after the other the food
sli-
1
cerwill start (see figure
6)).
You can now releasethe safety starter button.With the other hand you guide the food slide. Keep the safety push button de-
pressed with the thumb of your right hand as long as you want to slice. Gently
press the food against the face plate while slicing. When you release the safety push button, the food slicer will stop.To restart see the above instructions.
Slicing small pieces and
leftovers
Unfold the end piece holder
(see figure
69)
and attach it to the food slicer as shown in figure Q Make sure that the piece holder is engaged properly to the food slide. Use your left hand to guide
the end piece holder and
the food slide, while the
I
thumb of the right hand
holds the safety push but-
ton down.
Cleaning
Always unplug cord before cleaning. It is sufficient to wipe the plastic parts of the housing with a damp cloth. Never use scouring agents. Do not put the detachable
plastic parts into the
dish-
washerYou
should, how-
ever, give the slicer a tho-
rough cleaning in order to be sure that no perishable
food residues become
deposited on the machine, behind the face plate, or behind the cutting blade. Remove the end piece hol-
der and the food slide.
Removing the cutting blade (see figure
@I)
Turn the retaining screw
anti-clockwise with a coin.
Simultaneously with your
other hand push the cutting blade lightly against the sli-
cer to avoid that the blade falls down accidentally.
Caution:
Keep your fingers
away from the cutting edge. When cleaning the cutting
blade remember that the
cutting edge is very sharp.
Handle with care.
Removing the sliding table
Fold up the sliding table. Pull out the sliding table by using the recessed grip (see fig. 0) (the table can be assembled only in the fold up position; make sure that the two hooks oppo­site of the recessed grip are placed both inside the slic­ing table holder; then push the table back into posi­tion). Should the sliding table not come out turn the slice thickness selector clockwise so that the slid­ing table regains the exact vertical position.
Removing the face plate
Turn the slice thickness selector anti-clockwise until the face blade disengages (see fig.
0).
When not in use
Unplug the slicerwhen not in use. Make sure that the face plate extends the cut­ting blade slightly. Fold up the slicer. Store the cord in the cord storage (see
fig.@).
The sliding table does not stand up in the vertical position if the face plate is too far
out.Turn
the slice thickness selector clock­wise until the sliding table will stay in the vertical posi­tion. For compact storage fold the food slide and the end piece holder and clip toge­ther as shown in picture
03.
Optiil
Accessory
A special nonserrated ham/ prosciutto blade for cutting densely textured meats is separately available (model
# 009).
See your local dea-
ler or order it from the
KRUPS Customer Service
Department (see under
KRUPS Guarantee of Per-
formance).
Limited two years warranty Your KRUPS
product is covered by the following warranty: If, within two years from date of purchase, this KRUPS product fails to function because of defects in materials or workmanship, ROBERT KRUPS, North America, will, at its option, repair or replace the unit without charge, provided the owner returns:
0
the KRUPS product (securely
packed) and
0
proof of date of purchase to:
KRUPS Customer Service ROBERTKRUPS, North America 7 Reuten Drive CLOSTER, N.J. 07624
To assure prompt service, please in-
clude a letter indicating the specific cause for returning your KRUPS pro­duct.
Do not return any loose parts or
any accessories which
are
not defec­tive with your appliances to avoid damage and loss in transit.
This warranty will be void if malfunc­tion was caused by damage to the product by accident, misuse, use on frequency or voltage other than marked on the product and/or described in the instructions, abuse including tampering, damage in transit, or use for commercial
pur-
poses.This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
KRUPS GUARANTEE OF PERFORMANCE
This fine KRUPS product is manufac­tured according to a rigid code of quality standards, and, with a mini­mum of care, should give years of satisfying service. However, should the need arise for repairs or for re­placement parts (within or after the warrantypee, please do as fol­lows for the most convenient, fastest service.
Note the type number of your KRUPS
appliance.You
will need this informa­tion when calling our Customer Ser­vice
DepartmentType: #
213 A.
For parts orders or any other ques-
tions on how to operate your
KRU
PS product, call our CUSTOMER SER­VICE DEPARTMENT toll free (Mon-
day through Friday [except holidays]
from gAM
until 4PM Eastern Stan­dard lime) l-886-526-5377 (in New Jersey call
[26l] 767-5686).
For warranty and after-warranty ser-
vice, send your KRUPS appliance to:
KRUPS Customer Service ROBERT KRUPS, North America 7 Reuten Drive CLOSTER, New Jersey 07624
pad<
up your appliance carefully to avoid damage in shipping and be sure to provide us with the following information:
A. Your name and address and type
number of the appliance on the outside wrapping of the pack­aging.
B.
Tape a brief note to the body of
the machine indicating:
how long you own it; the possible defect.
IMPORTANT:
ONLY
SENDTHE
DEFECTIVE
APPUANCE.
KEEP AU REMOVABLE PARTS AT HOME TO AVOID FURTHER DAMAGE IN TRANSPORT!
We will repair or replace your KRUPS product without delay and send it back to you with no charge for
ship­piig (if you send us a receipt for the
regular UPS or Parcel Post charges, we will even reimburse you for ship­ping charges, within or after the war­ranty period).
On all repair work to be done after the warranty period, our Customer Service Department will bill you for material and labor only.
Do not return
ywppliance
to the
-The
KRUPS Guarantee of Per­formance program has been de­signed to provide you with the best possible service using genuine KRUPS parts.
All repair work and replaced parts will carry an extended
g&z&y-warranty.
Loading...