Kraus KEF-14607CH User Manual
7.9’’
O
O
4’’
Exquisite Collection
Installation Manual
Wal l-mount ed single -lever ba throom fa ucet
2.6’’
45
O
2.6’’
3.5’’
5.1’’
O
5
4
O
8
0.8’’
O
2
5
5.7’’
6.8’’
KR AU S B r a n d B at h r o om Fau c e t s L imit e d L i f e t i me Wa r r a n t y
KRAUS is proud to offer its customers the strongest, most durable ceramic cartridges in all solid
brass Bathroom Faucets it manufactures. KRAUS guarantees all products to be free of defect in
materials and craftsmanship. All KRAUS BRAND Bathroom Faucets carry a limited lifetime warranty
from the original date of purchase.
If a product fails due to defect in material or craftsmanship during the warranty period, KRAUS will
repair or replace the items at its sole discretion. Warranty does not apply when the item has been
tampered with, misused, improperly installed, altered, or damaged due to abuse or accident.
Proof of purchase (original sales receipt) must be provided to KRAUS for all warranty claims.
Please contact one of our representatives if you need any additional details.
Before Your Installation
Che ck to mak e sure yo u have th e follo wing pa rts ind icate d below :
KEF-14 6 0 7
Tools You Will Need
All KRAUS products must be installed by a licensed professional plumber or contractor to avoid any
improper use or installation.
IN NO EVENT SHALL KRAUS BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES, INSTALLATION COST, LABOR, TRAVEL TIME, FREIGHT COSTS
INCURRED, LOST PROFITS, OR CONTINGENT LIABILITIES.
KRAUS USA Inc. makes no representation that its products comply with any or all local building or
plumbing codes. It is the consumer’s responsibility to determine local code compliance.
This warranty extends to the original purchaser and first
consumer.
Conta ct U s Tol l-Free at 1 -8 00 -7 75 -0703 ; or v is it o ur w ebsite at w ww.kr au su sa .c om 2008 -2 011 K ra us U SA In c.
Adjus ta ble wre nc h
Phill ip s screw dr iver
Spann er f or body
(su pp li ed)
Conta ct U s Tol l-Free at 1 -8 00 -7 75 -0703 ; or v is it o ur w ebsite at w ww.kr au su sa .c om 2008 -2 011 K ra us U SA In c.
Adjus ta ble wre nc h
Plp e ta pe
(su pp li ed)
Replacement Parts
Keep this manual for ordering replacement parts.
Installation
17
16
15
14
13
Cold wa te r pipe
(NOT IN CLUDE D)
12
11
Hot wat er p ipe
10
(NOT IN CLUDE D)
9
1
2
8
Cold wate r pi pe
(NO T INCLU DED)
Hot water p ip e
(NO T INCLU DED)
Trouble - Shooting
3
4
5
7
6
Cold wate r pi pe
(NO T INCLU DED)
Hot water p ip e
(NO T INCLU DED)
O-ri ng
1.
Plas ti c co ve r
2.
Scre w
3.
O-ri ng
4.
Deco ra ti ve r ing
5.
Set sc re w
6.
Deco ra ti ve c ap
7.
Hand le
8.
Span ne r fo r sp out
9.
Spou t
10.
Deco ra ti ve c ap
11.
Set sc re w
12.
Deco ra ti ve b oard
13.
Fixi ng b oa rd
14.
Conn ec ti ng p ole
15.
Plas ti c co ve r
16.
Valve
17.
Probl e m Cause Actio n
Leaks u nd ernea th h andle
Aerator leaks or has an inconsistent
water flow pattern.
Water will not shut off completely.
Conta ct U s Tol l-Free at 1 -8 00 -7 75 -0703 ; or v is it o ur w ebsite at w ww.kr au su sa .c om 2008 -2 011 K ra us U SA In c.
Adjusting ring or cap has come loose.
Aerator is dirty or misfitted.
Dirty or worn out plastic washer in the
cartridge.
Tighten the adjusting ring or cap.
Unscrew the aerator to check rubber packing
or replace the aerator.
Remove handle and cartridge to check if ceramic
disk is damage permanently or dirty.
Re-install cartridge.
Place sufficient Teflon tape on hot/cold water supply
pipe lines. Insert them into the corresponding threaded
screw of valve 17 and install it into the wall. Open the
water supply to check if there is leakage. Loosen
screw 3 and take the plastic cover 2 off. Open the
1
cartridge to make sure there is no leakage. Close the
cartridge after checking. Remove plastic cover 16.
Open cartridge and remove the dirt in the pipe. Close
the cartridge and install the plastic cover 16 and 2 into
valve.
2
Seal the wall after checking for leakage. If there is
no leakage, remove plastic cover 16 and 2.
3
4
Place sufficient Teflon tape on connecting pole 15.
Screw it into corresponding screwed hole of valve 17
(If the connecting pole is too long please shorten it
with a saw; refer to dimensions for detail size). Install
decorative board 13 and Fixing board 14 to valve.
5
6
Install connecting pole 15 to the spout 10. Screw the
set screw 12 into spout 10 with alley key and install the
decorative cap 11. Install handle 8 to the corresponding
position to valve 17. Tighten decorative screw 6 with
7
Conta ct U s Tol l-Free at 1 -8 00 -7 75 -0703 ; or v is it o ur w ebsite at w ww.kr au su sa .c om 2008 -2 011 K ra us U SA In c.
8
9
alley key and place cap 7 afterwards.
Loading...