Page 1
TP-583Txr/TP-583Rxr Quick Start
P/N:
2900- 301159QS
Rev:
2
Scan for full manual
TP-583Txr/TP-583Rxr Quick Start Guide
This guide helps you install and use your TP-583Txr/TP-583Rxr for the first time.
Go to www.kramerav.com/downloads/TP-583Txr, TP-583Rxr to download the latest user manual and check
if firmware upgrades are available.
Step 1: Check what’s in the box
TP-583Txr HDMI Line Transmitter or
1 Power adapter and cord
1 Quick start guide
TP-583Rxr HDMI Line Receiver
4 Rubber feet
1 Bracket set
Step 2: Get to know your TP-583Txr and TP-583Rxr
TP-583Txr
#
Feature
Function
1
IN LED
Lights green when an active source device input signal is detected.
2
OUT LED
Lights green when an active, far-end sink (acceptor) connection is
detected via the HDBT link.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT
receiver.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a receiver (for
example, TP-583Rxr, TP-780Rxr and so on).
6
HDMI™ IN Connector
Connect to an HDMI source.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin Terminal Block Connector
Connect to a laptop to control the receiver or perform firmware
upgrade.
Connect to a controller device (for example, SL-240C) to serially
control a remote device (for example, the HDMI OUT acceptor) that
is connected to TP-583Rxr.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.
Page 2
TP-583Rxr
#
Feature
Function
1
IN LED
Lights green when an active, far-end source device input signal is
detected via the HDBT link.
2
OUT LED
Lights green when an active sink (acceptor) connection is detected.
3
LINK LED
Lights green when an HDBT link is established with the HDBaseT
transmitter.
4
ON LED
Lights green when the device receives power.
5
LINE RJ-45 Connector
Connect to the RJ-45 HDBT LINE connector on a transmitter (for
example, TP-583Txr, TP-780Txr and so on).
6
HDMI OUT Connector
Connect to an HDMI acceptor.
7
SETUP DIP-switches
Set the operation DIP-switches.
8
RS-232 (G, Rx, Tx) 3-pin Terminal Block
Connector
Connect to a laptop to control the receiver or perform firmware
upgrade.
Connect to a serially controlled device (for example, the HDMI OUT
acceptor) to enable its control by a remote controller device (for
example, SL-240C) that is connected to TP-583Txr.
9
IR 3.5mm Mini Jack Connector
Connect to an external infrared emitter / sensor.
10
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Install TP-583Txr/TP-583Rxr
Install TP-583Txr/TP-583Rxr using one of the following methods:
• Attach the rubber feet and place the unit on a flat surface.
• Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to
www.kramerav.com/downloads/TP-583Txr, TP-583Rxr.
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/TP-583Txr, TP-583Rxr).
Page 3
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your TP-583Txr/TP-583Rxr. For best results, we recommend
that you always use Kramer high-performance cables to connect AV equipment to TP-583Txr/TP-583Rxr.
RJ-45 Pinout:
For HDBT cables, it is recommended that the cable
ground shielding be connected/soldered to the
connector shield:
PIN EIA /TIA 568B
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
For optimum range and performance use the recommended Kramer cables available at
www.kramerav.com/product/TP-583Txr, TP-583Rxr.
Page 4
DIP-Switch Settings
The DIP-switches are used to:
• Set the HDBT range.
• Set the compression levels and resolutions.
• Enable RS-232 signal extension.
• Upgrade the firmware.
• Determine IR signal pass-through.
All the DIP-switches are set to OFF (up) by default.
To use your TP-583Txr or TP-583Rxr with any other standard HDBaseT
extender (without compression), verify that DIP-switch 1B is OFF (up).
A – DIP-switch Settings
#
Feature
DIP-switch Settings
1A
Set HDBT Range
OFF (up) – HDBaseT normal range.
ON (down) – HDBaseT ultra-long range (to enable increased range at a
reduced bandwidth).
The ultra-long range mode is activated when on at least one of
the devices DIP-switch 1 is set to ON.
2A
Set the Compression Level
(for extended range)
OFF (up) – Standard compression level.
ON (down) – High compression level for additional extension.
B – DIP-switch Settings
Changes to DIP-switches 2B and 3B only take effect after power cycling the device.
#
Feature
DIP-switch Settings
1B
Define Compressed
Resolutions
OFF (up) – Compress signal resolutions higher than 1080p.
ON (down) – Compress all signal resolutions to enable extended reach.
2B, 3B
Define RS-232 Function
OFF (up), OFF (up) – Embed RS-232 data and control signals over the
extension line.
Other DIP-switch settings are reserved for firmware upgrade. For
further details, contact support@kramerav.com.
4B
Define IR Pass-through
OFF (up) – Pass-through the IR signal to the IR port via IR cable.
ON (down) – Add IR modulation to the IR output signal (applies only when
the IR port is connected to an IR emitter cable).
The IR Pass-through DIP-switch setup depends on the IR control
configuration. We recommend that you test which position best
suits your application.
Step 5: Connect the power
Connect the 12V DC power adapter to TP-583Txr/TP-583Rxr and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power adapter that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Loading...