KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
PS E - 4
10G Quad POE Injector
P/N: 2900-300487 Rev 1
PSE-4 – Contents
i
Contents
1 Introduction 1
2 Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 2
2.3 Recycling Kramer Products 3
3 Overview 4
4 Defining the PSE-4 5
5 Connecting the PSE-4 6
6 Wiring the DGKat TP RJ-45 Connectors 8
7 Technical Specifications 9
Figures
Figure 1: PSE-4 10G Quad POE Injector Front Panel 5
Figure 2: PSE-4 10G Quad POE Injector Rear Panel 5
Figure 3: Connecting the PSE-4 10G Quad POE Injector 6
Figure 4: The PSE-4 Supplying Power to Receivers 7
Figure 5: TP Pinout Wiring 8
PSE-4 - Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront the video, audio, presentation, and broadcasting
professional on a daily basis. In recent years, we have redesigned and upgraded
most of our line, making the best even better!
Our 1,000-plus different models now appear in 14 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters; GROUP 11:
Sierra Products; GROUP 12: Digital Signage; GROUP 13: Audio; and GROUP 14:
Collaboration.
Congratulations on purchasing your Kramer PSE-4 10G Quad POE Injector, which
is ideal for the following typical applications:
Provide power to in-wall mounted devices
Provide power to remote devices with no access to power
2
PSE-4 - Getting Started
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Go to http://www.kramerav.com/downloads/PSE-4 to check for up-to-date
user manuals, application programs, and to check if firmware upgrades
are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cable) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
Position your Kramer PSE-4 away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
2.2 Safety Instructions
Caution:
No operator serviceable parts inside the unit
Warning:
Use only the Kramer Electronics power supply that is
provided with the unit
Warning:
Disconnect the power and unplug the unit from the wall
before installing
i
!
!
PSE-4 - Getting Started
3
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.
4
PSE-4 - Overview
3 Overview
The PSE-4 is a four-way PoE (Power-over-Ethernet) injector which supports 4K
UHD video.
The PSE-4 provides power remotely over Ethernet to up to four devices capable of
acting as PoE acceptors, (for example, the WP-5VH2, where it might be difficult to
connect an external power supply). This allows a single HDBT LAN cable to
provide both data and electrical power to compatible devices.
In particular, the PSE-4 features:
A total range of up to 100m (328ft) @ 4K on shielded BC-HDKat6a cable (or
equivalent)
4K support
48V DC power
A Kramer MegaTOOLS ® enclosure
PSE-4 - Defining the PSE-4
5
4 Defining the PSE-4
Figure 1 defines the front panel of the PSE-4 10G Quad POE Injector.
Figure 1: PSE-4 10G Quad POE Injector Front Panel
#
Feature
Function
1
POE STATUS 1~4
LEDs
The relevant LED lights green when the PSE-4 provides
power over Ethernet to a remote device on that port
2
ON LED
Lights green when the device is powered on
Figure 2 defines the rear panel of the PSE-4 10G Quad POE Injector.
Figure 2: PSE-4 10G Quad POE Injector Rear Panel
#
Feature
Function
3
LAN 1 RJ-45 Connector
Connect to the first Ethernet/HDBT LAN
4
LAN + POE 1 RJ-45
Connector
Connect to the first Ethernet/HDBT LAN which is to
be powered by the PoE
5
LAN 2 RJ-45 Connector
Connect to the second Ethernet/HDBT LAN
6
LAN + POE 2 RJ-45
Connector
Connect to the second Ethernet/HDBT LAN which
is to be powered by the PoE
7
LAN 3 RJ-45 Connector
Connect to the third Ethernet/HDBT LAN
8
LAN + POE 3 RJ-45
Connector
Connect to the third Ethernet/HDBT LAN which is
to be powered by the PoE
9
LAN 4 RJ-45 Connector
Connect to the fourth Ethernet/HDBT LAN
10
LAN + POE 4 RJ-45
Connector
Connect to the fourth Ethernet/HDBT LAN which is
to be powered by the PoE
11
48V DC 2-pin terminal
block
Connect to the +48V DC power supply
6
PSE-4 - Connecting the PSE-4
5 Connecting the PSE-4
Always turn off the power to each device before connecting it to your
PSE-4. After connecting your PSE-4, connect its power and then turn
on the power to each device.
Figure 3: Connecting the PSE-4 10G Quad POE Injector
To connect the PSE-4 as illustrated in the example in Figure 3:
1. Connect the first HDBT transmitter, (for example, the WP-5VH2) to the
LAN + POE 1 RJ-45 connector on the rear panel of the PSE-4.
2. Connect the LAN 1 RJ-45 connector on the rear panel of the PSE-4 to the
HDBT receiver, (for example, the VS-1616D).
3. Repeat steps 1 and 2 for an additional three devices.
i
PSE-4 - Connecting the PSE-4
7
4. Connect the supplied power adapter to the PSE-4 and plug the power
adapter into the mains supply.
The PSE-4 provides power to the WP-5VH2 HDBT transmitters.
Note: The PSE-4 can provide power via the LAN+POE ports to either an HDBT
transmitter or receiver. Figure 3 illustrates this by showing the PSE-4 providing
power to transmitters. The PSE-4 can also provide power to receivers as shown in
Figure 4.
Figure 4: The PSE-4 Supplying Power to Receivers
8
PSE-4 - Wiring the DGKat TP RJ-45 Connectors
6 Wiring the DGKat TP RJ-45 Connectors
Connect/solder the cable shield to the RJ-45 connector shield at both ends of the
cable.
Do not use a crossed TP cable with this product.
Using a TP cable that is incorrectly wired may cause permanent
damage to the device
Do not use unshielded TP cables with this product
Figure 5 defines the TP pinout using a straight pin-to-pin cable with RJ-45
connectors.
EIA /TIA 568B
Figure 5: TP Pinout Wiring
PIN
Wire Color
1
Orange / White
2
Orange
3
Green / White
4
Blue
5
Blue / White
6
Green
7
Brown / White
8
Brown
Pair 1
4 and 5
Pair 2
1 and 2
Pair 3
3 and 6
Pair 4
7 and 8
!
PSE-4 - Technical Specifications
9
7 Technical Specifications
INPUT/OUTPUT:
4 HDBaseT/LAN on RJ-45 connectors
4 HDBaseT/LAN + POE on RJ-45 connectors
OPERATION BANDWIDTH:
Up to 10.2Gbps (3.4Gbps per data channel)
COMPLIANCE WITH HDMI
STANDARD:
Supports HDMI, HDCP
INDICATOR LEDS:
ON, POE STATUS
POWER CONSUMPTION:
48V DC 2.5A
POWER PROVISION:
Up to 30W per output (120W total)
OPERATING TEMPERATURE:
0° to +40°C (32° to 104°F)
STORAGE TEMPERATURE:
–40° to +70°C (–40° to 158°F)
HUMIDITY:
10% to 90%, RHL non-condensing
COOLING:
Convection, vents
ENCLOSURE TYPE:
Aluminium
DIMENSIONS:
18.75cm x 11.5cm x 2.54cm (7.38" x 4.53" x 1") W, D, H
RACK MOUNT:
With optional adapter
FURNITURE MOUNT:
With included rubber feet
PRODUCT WEIGHT:
0.16kg (0.35lbs) approx.
SHIPPING WEIGHT:
0.67kg (1.48lbs) approx.
VIBRATION:
ISTA 1A in carton (International Safe Transit Association)
SAFETY REGULATORY
COMPLIANCE:
CE
ENVIRONMENTAL
REGULATORY COMPLIANCE:
Complies with appropriate requirements of RoHs and
WEEE
INCLUDED ACCESSORIES:
Power supply
OPTIONS:
RK-4PT 19” rack adapter
WARRANTY:
7 years parts and labor
Specifications are subject to change without notice at http://www.kramerelectronics.com
For the latest information on our products and a list of Kramer distributors, visit
our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
P/N:
2900-300487
Rev:
1
!
Loading...