OSP-SM10S Quick Start
P/N:
2900- 301238QS
Rev:
1
Scan for full manual
OSP-SM10S Quick Start Guide
This guide helps you install and use your OSP-SM10S for the first time.
Go to www.kramerav.com/downloads/OSP-SM10S to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
2 OSP-SM10S 10G SFP+ Simplex Transceivers (A and B)
1 Quick start guide
Step 2: Get to know your OSP-SM10S
#
Feature
Function
1
LC Connectors
For connecting fiber optic cable. Covered with protective cap when not in use.
2
Bail (Handle)
Pull down the handle for easy removal of the transceiver from the optical device.
3
Protective Cap
Protects the LC connector from dust.
Note: When transporting or storing an unconnected device, keep the cap on to protect
against dust.
4
SFP+ Module Interface
Connects to the optical module SFP+ port.
Step 3: Safety Instructions
Warning: Class 1 Laser Product:
• Invisible laser radiation present.
• Avoid long-term viewing of laser.
• Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes,
microscopes and magnifying lenses, but not spectacles or contact lenses).
• Avoid placing optical devices in the emitted beam that could cause the concentration of the
laser radiation to be increased.
• Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
Step 4: Operation and Installation Warnings
• OSP-SM10S is designed to be used with LC(PC) and LC(UPC) cable connectors. Using an LC(APC) connector
causes poor performance and can damage the optical module connector.
• Always inspect and clean the connectors before you make a connection.
• Always use the connector housing to plug or unplug a fiber cable.
• Never touch the end face of the fiber connectors.
Step 5: Install the OSP-SM10S
Always install transceiver A to one extension device and transceiver B to the other
extension pairing device.
To install the 10G SFP+ Simplex Transceiver:
1. Make sure the bail is pushed up, in the closed position.
2. Insert the OSP SFP+ transceiver into the relevant optical device SFP+ slot
and push it in until it clicks.
3. Before connecting the optical fiber cable, remove the protective cap and store
it in a safe place for future use.
To remove the 10G SFP+ Simplex Transceiver:
1. Pull the bail down to release the transceiver unit.
2. Pull the transceiver unit out by the bail from the optical device SFP+ slot.
3. If needed, put the protective cap back on.
For optimum range and performance use the recommended Kramer cables available at
www.kramerav.com/product/OSP-SM10S. Using third-party cables may cause damage!
Step 6: Technical Specifications
Transceiver Wavelength:
A: 1270 DFB transmitter /1330nm receiver
B: 1330 DFB transmitter /1270nm receiver
Optical Fiber Line Type:
Single-mode
Optical Transmitter Type:
DFB
Typical Optical Transmission Power:
-5dBm
Typical Optical Maximum Receiver
Sensitivity:
-14dBm
Typical Optical Maximum Loss Budget:
9dB
Ports:
1 strand fiber optic LC (PC/UPC) connector for reception and transmission
SFP+ compliant pluggable interface
Note: Do not use with LC(APC) connectors.
Data Rate:
10Gbps
Maximum Reach
24km
Standards Compliance:
IEEE 802.3AE, SFF-8431, SFF-8472
Laser Safety Compliance:
Laser Class I
Regulatory Certifications:
FDA: CDRH 1040.10
TUV: EN60950-1:2006+A11+A1+A12+A2; EN60825-1:2014; EN608252:2004+A1+A2
UL: 60950-1; CSA C22.2 No. 60950-1-07:2014
EMC CE: EN 55032:2010; EN 55024:2010
CB: IEC 60950-1 2nd Edition :2014
RoHS: Directive 2011/65/EU
Operating Temperature:
0° to 70°C
Storage Temperature:
-40° to 85°C
Humidity:
5% to 95% RH
Power Consumption:
1W
Product Dimensions:
1.33cm x 5.7cm x 0.85cm (0.52" x 2.2" x 0.33") W, D, H
Product Weight:
0.018kg (0.04lbs)
Shipping Dimensions:
4.1cm x 12.6cm x 8.4cm (1.6" x 5" x 3.3") W, D, H
Shipping Weight:
0.06kg (0.13lbs)
Specifications are subject to change without notice at www.kramerav.com
Loading...