OSP-MM1 Quick Start
P/N:
2900- 301181QS
Rev:
5
W
Scan for full manual
OSP-MM1, OSP-SM10 Quick Start Guide
This guide helps you install and use your OSP-MM1 / OSP-SM10 for the first time.
Go to www.kramerav.com/downloads/OSP-MM1 or www.kramerav.com/downloads/OSP-SM10 to
download the latest user manual and check if firmware upgrades are available.
Step 1: Check what’s in the box
OSP-MM1 Optical MM 850nm 10G SFP+ Transceiver or
OSP-SM10 Optical SM 1310nm 10G SFP+ Transceiver
1 Quick start guide
Step 2: Get to know your OSP-MM1 / OSP-SM10
#
Feature
Function
1
Cap
Protects the LC connectors from dust.
Note: When transporting or storing an unconnected device, keep the cap on to protect
against dust.
2
LC Connectors
For connecting fiber optic cables. Covered with protective cap when not in use.
3
Bail (Handle)
Pull down the handle for easy removal of the transceiver from the optical device.
4
SFP+ Device Interface
Connects to the optical device SFP+ port.
Step 3: Safety Instructions
Warning: Class 1 Laser Product:
• Invisible laser radiation present.
• Avoid long-term viewing of laser.
• Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and magnifying
lenses, but not spectacles or contact lenses).
• Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be
increased.
Step 4: Operation and Installation Warnings
• OSP-MM1 and OSP-SM10 are designed to be used with LC(PC) and LC(UPC) connectors. Using an LC(APC)
connector causes poor performance and can damage the connector.
• Always inspect and clean the connectors before you make a connection.
• Always use the connector housing to plug or unplug a fiber.
• Never touch the end face of the fiber connectors.
Step 5: Install the OSP-MM1 / OSP-SM10
To install the OSP SFP+ transceiver:
1. Make sure the bail is pushed up, in the closed position.
2. Insert the OSP SFP+ transceiver into the relevant optical device SFP+ slot
and push it in until it clicks.
3. Remove the protective cap and store it in a safe place for future use.
To remove the OSP SFP+ transceiver:
1. Pull the bail down to release the transceiver unit.
2. Pull the transceiver unit out by the bail from the optical device SFP+ slot.
3. If needed, put the protective cap back on.
For optimum range and performance use the recommended Kramer cables available at www.kramerav.com/product/OSP-MM1
or www.kramerav.com/product/OSP-SM10 Using third-party cables may cause damage!
Step 6: Technical Specifications
OSP-MM1
OSP-SM10
Transceiver Wavelength:
850nm
1310nm
Optical Fiber Line Type:
Multi-mode
Single-mode
Optical Transmitter Type:
VCSEL
DFB
Typical Optical Transmission Power:
-2.5dBm
-2.5dBm
Typical Optical Maximum Receiver Sensitivity:
-11.1dBm
-14.4dBm
Typical Optical Maximum Loss Budget:
8.6dB
11.9dB
Ports:
2 strand fiber optic LC (PC/UPC) connector for reception and
transmission
SFP+ compliant pluggable interface
Note: Do not use with LC(APC) connectors.
Data Rate:
10Gbps
Standards Compliance:
IEEE 802.3ae, SFF-8431
Laser Safety Compliance:
Laser Class I
Regulatory Certifications:
FDA CDRH 21 CFR 1040 and Laser Notice No. 50
UL and CUL EN60950-2:2007
RoHS6 Directive 2002/95/EC
EMC EN 55022:2006+A1:2007; EN 55024:1998+A1+A2:2003
Operating Temperature:
0° to 70°C
Storage Temperature:
-40° to 85°C
Humidity:
5% to 95% RH
Power Consumption:
1W
Product Dimensions:
1.33cm x 5.7cm x 0.85cm (0.52" x 2.2" x 0.33") W, D, H
Product Weight:
0.018kg (0.04lbs)
Shipping Dimensions:
4.1cm x 12.6cm x 8.4cm (1.6" x 5" x 3.3") H, W, D
Shipping Weight:
0.06kg (0.13lbs)
Specifications are subject to change without notice at www.kramerav.com
Loading...