P/N: 2900-301232 Rev 7 www.kramerAV.com
USER MANUAL
MODEL:
MegaEdge
All Day Portable Power Supply
Kramer Electronics Ltd.
MegaEdge – Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Typical Applications 3
Defining MegaEdge All Day Portable Power Supply 4
Mounting MegaEdge 5
Operating and Controlling MegaEdge 6
Replacing the MegaEdge Battery 7
Technical Specifications 8
Kramer Electronics Ltd.
MegaEdge – Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
• Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
• Review the contents of this user manual.
Go to www.kramerav.com/downloads/MegaEdge to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving Best Performance
• Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
• Do not secure the cables in tight bundles or roll the slack into tight coils.
• Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
• Position your Kramer MegaEdge away from moisture, excessive sunlight and dust.
Safety Instructions
Caution:
• This equipment is to be used only inside a building. It may only be connected to
other equipment that is installed inside a building.
• For products with relay terminals and GPI\O ports, please refer to the permitted
rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.
Warning:
• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.
• Do not open the unit. High voltages can cause electrical shock! Servicing by
qualified personnel only.
• To ensure continuous risk protection, replace fuses only according to the rating
specified on the product label which located on the bottom of the unit.
Kramer Electronics Ltd.
MegaEdge – Introduction
2
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling.
Overview
Congratulations on purchasing your Kramer MegaEdge-US and/or MegaEdge-WW All Day
Portable Power Supply.
Although this user manual describes the MegaEdge it refers to both MegaEdge-US and
MegaEdge-WW, unless specified otherwise.
MegaEdge has two AC Power Sockets, two USB type A charging stations, and one USB type
C charging station.
MegaEdge-US outputs 120V AC.
MegaEdge-WW outputs 220V AC.
Advanced and User-friendly Operation
• Intelligent, microprocessor controlled, safe, and reliable.
• Battery capacity percentage indicator.
• Electronic overload protection with automatic shutdown.
• Low battery voltage shutdown.
• Overheat protection with automatic shutdown.
• Over current protection.
• Short circuit protection.
• Standby timer off.
• Charging over timer protection.
• Temperature protection.
Kramer Electronics Ltd.
MegaEdge – Introduction
3
Flexible Connectivity
• Portable power.
• All day continuous ‘Bring Your Own Device’ (BYOD) charging.
• Powers any laptop or mobile device.
• Maximizes learning flexibility.
• Average charging capacity.
▪ For smartphone: approx. 35 times (iPhone 1900mah).
▪ For tablet: approx. 10 times (iPad 6930mah).
▪ For a Laptop: approx. 3-4 times.
Typical Applications
MegaEdge is ideal for the following typical applications:
• Active class learning freedom & flexibility.
• Mobile podium.
Kramer Electronics Ltd.
MegaEdge – Defining MegaEdge All Day Portable Power Supply
4
Defining MegaEdge All Day Portable Power Supply
This section defines MegaEdge.
MegaEdge-WW
MegaEdge-US
220V AC universal outlets
on MegaEdge-WW
Figure 1: MegaEdge All Day Portable Power Supply
#
Feature
MegaEdge-US Function
MegaEdge-WW Function
AC Power
Connector (x2)
Connect to up to two US power
consuming devices simultaneously.
Connect to up to two power consuming
devices simultaneously to a universal
socket.
When a single power socket is connected, consumption should not exceed
5A. When both power sockets are connected, the total consumption should
not exceed 6A.
5V-2A USB Fast
Charging Port (x2)
Use to charge a mobile device.
USB-C
Use to charge a mobile device.
Control Button
Short press to turn MegaEdge On.
Once on, each additional short press toggles MegaEdge AC power outlets
On/Off
MegaEdge consumes some power when the AC power indicator is on
even when no devices are connected to it.
Long press to turn MegaEdge Off.
Power On Indicator
LED
Lights blue when MegaEdge is on.
Numeric LED
Display
Indicates percent of power remaining.
AC Indicator LED
Lights red when AC power enabled.
USB DC power is always on when MegaEdge is on.
Mounting Bracket
Used with security screw for securing the MegaEdge to the table.
Security Screw (2)
For securing the MegaEdge to the table.
1 2 3 4 5 6 7 8 9
Kramer Electronics Ltd.
MegaEdge – Mounting MegaEdge
5
Mounting MegaEdge
This section provides instructions for mounting MegaEdge. Before installing, verify that the
environment is within the recommended range:
• Operation temperature – 0 to 40C (32 to 104F).
• Storage temperature – -40 to +70C (-40 to +158F).
• Humidity – 10% to 90%, RHL non-condensing.
Caution:
• Mount MegaEdge before connecting to power.
Warning:
• Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
• Avoid uneven mechanical loading.
To mount the MegaEdge on a table
Install MegaEdge
1. Carefully place MegaEdge over the
edge of a table at the desired location
so that the table edge is pressed
against the device.
2. Secure MegaEdge to the table using
the Torx bit and the two security screws
provided.
3. Tighten each security screw through
the MegaEdge mounting bracket into
the table.
Kramer Electronics Ltd.
MegaEdge – Operating and Controlling MegaEdge
6
Operating and Controlling MegaEdge
MegaEdge requires an AC extension cord with a C5 connector.
Use the recommended AC Reel adapter
(see www.kramerav.com/product/MegaEdge).
To Charge MegaEdge
When not in use, plug it into an AC outlet for at least 8 hours to fully charge the MegaEdge.
To Turn MegaEdge On
• Press the Control button.
Power On LED lights blue.
To Turn MegaEdge On/Off
• Press the Control button for 3 seconds.
Power On LED is no longer lit.
To Toggle AC Power On/Off
• Press the Control Button to toggle between AC power On and AC power Off
AC LED is lit red when AC is on.
MegaEdge consumes some power when the AC power indicator is on even when no devices
are connected to it.
When no power is being used, the MegaEdge powers off automatically after 1 minute.
MegaEdge batteries are rated to run 500 cycles and are replaceable.
MegaEdge-WW outputs 220V AC and cannot be used with devices that only support 120V
AC.
Kramer Electronics Ltd.
MegaEdge – Replacing the MegaEdge Battery
7
Replacing the MegaEdge Battery
1. Unplug MegaEdge from AC power.
2. Remove the 2 Torx screws securing MegaEdge to the table using the Torx bit provided.
3. Detach MegaEdge from the table and place on a flat surface.
4. Open the MegaEdge cover by removing the four screws indicated in Figure 2.
5. Unplug the AC and USB extension cords from the MegaEdge battery.
6. Place the new battery into MegaEdge.
7. Plug the AC and USB extension cords into the new MegaEdge battery.
8. Close the MegaEdge cover using the four screws indicated in Figure 2.
9. Follow the instructions for remounting MegaEdge (see Mounting MegaEdge on page 5).
Figure 2: MegaEdge cover screws
Kramer Electronics Ltd.
MegaEdge – Technical Specifications
8
Technical Specifications
Ports
2 AC Power Sockets
On a 5A/125V Power Socket
2 USB Type A
On a female USB type A connector
1 USB Type C
On a female USB type C connector
Controls
Front Panel
1 Power button (also used to toggle AC power On/Off)
Indication LEDs
Front Panel
1 Power on LED
1 AC on LED
Cooling
Fan Ventilation
AC Adapter
Input
AC 100V-240V, 50/60Hz 2.0 A
Output
DC 24V /2A
Power
Consumption
AC 100V-240V, 50/60Hz
MegaEdge-US
MegaEdge-WW
AC power Output
AC Output Voltage (Nominal)
120V
220V
Continuous AC Output Power
200W
200W
Maximum AC Output Power
250W
250W
AC Output Frequency
60Hz
50Hz
AC Output Waveform
Modified sine wave
DC power Output
Dual USB Output
Voltage: 5V Current: Max. 3.4 A
TYPE-C Output
Voltage: 5V Current: Max. 3.1 A
Battery
Type
SANYO (Panasonic) Lithium-ion Battery NCR18650BF
3350mAh*24
Drain
No load: < 1.5mA
AC Load: 200W Time：>1.1h，100W：>1.8h
DC Load: 3.0A Time：>14.3h，2.0A：>22.2h
Rated Capacity
3200mAh 0.64A discharge at 20°C (68°F)
Capacity (Minimum)
3250mAh 0.65A discharge at 25°C (77°F)
Capacity (Typical)
3350mAh (Reference only)
Normal Voltage
3.6V (0.65A discharge)
Discharging End Voltage
2.5V Charging Current (Std.)
1.625A
Charging Voltage
4.20 +0.03V
Continuous Discharge Current (Max.)
4.875A 0°C ~ +40°C (32°F to 104°F)
Internal Resistance
less than 100m (AC impedance 1 kHz)
Environmental
Conditions
Operating Temperature
0° C to +25°C (32°F to 77°F)
Storage Temperature
-10°C to +60°C (14°F to 140°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE
Enclosure
Type
Aluminum, Steel
General
Net Dimensions (W, D, H)
32.2cm x 25.4cm x 18.2cm
(13.07" x 10.0" x 7.17")
Shipping Dimensions (W, D, H)
44.5cm x 36.5cm x 28.5cm (17.5" x 14.3" x 11.2")
Net Weight
4.6kg (10.2lbs) approx.
Shipping Weight
6.8kg (15lbs) approx.
Accessories
Included
1 Torx bit (1/4” T20 25mm)
2 T20 Torx screws
Optional
1 Retractable AC Power Cord Reel 5m (15ft)
Charging Time
8h
The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:
What is Covered
This limited warranty covers defects in materials and workmanship in this product.
What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use or
maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to the carrier),
lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting from the installation or
removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Kramer Electronics
to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product. This limited warranty does not
cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the technology
and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other product or technology
with which the product may be used.
How Long this Coverage Lasts
The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:
1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year
warranty for firmware and software updates; all Kramer VIA accessories, adapters, tags, and dongles are covered by a standard one (1) year
warranty.
2. Kramer fiber optic cables, adapter-size fiber optic extenders, pluggable optical modules, active cables, cable retractors, ring mounted
adapters, portable power chargers, Kramer speakers, and Kramer touch panels are covered by a standard one (1) year warranty. Kramer
7-inch touch panels purchased on or after April 1st, 2020 are covered by a standard two (2) year warranty.
3. All Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all streaming, and all wireless products
are covered by a standard three (3) year warranty.
4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.
5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for
three (3) years).
6. K-Touch software is covered by a standard one (1) year warranty for software updates.
7. All Kramer passive cables are covered by a lifetime warranty.
Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or owners of
this product.
What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under
this limited warranty:
1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and
labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs
necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same
function as the original product. If a direct or similar replacement product is supplied, the original product’s end warranty date remains
unchanged and is transferred to the replacement product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought
under this limited warranty.
What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics
products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned uninsured, you assume
all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re-installation of this product from or
into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any adjustment of user controls or any
programming required for a specific installation of this product.
How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the
Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service providers, visit our web
site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer Electronics
reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be required (RMA number).
You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original carton, for
shipping. Cartons not bearing a return authorization number will be refused.
Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID
FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL
THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or the limitation
of liability to specified amounts, so the above limitations or exclusions may not apply to you.
Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT
PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR
EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON -MOSS WARRANTY ACT (15
U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU, AND
ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE,
SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.
Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by Kramer
Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an authorized Kramer
Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product
registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of satisfaction.
.
www.KramerAV.com
info@KramerAV.com
P/N:
2900-301232
Rev:
7
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where
updates to this user manual may be found.
We welcome your questions, comments, and feedback.
All brand names, product names, and trademarks are the property of their respective owners.
Loading...