USER MANUAL
MODELS:
KT-107, 7” Touch Panel
KT-107RB, 7” Touch Panel
P/N: 2900-300696 Rev 1 www.kramerAV.com
KT-107, KT-107RB - Introduction
i
Contents
Introduction 1
Getting Started 1
Overview 2
Typical Applications 3
Defining the KT-107, KT-107RB 4
KT-107 Touch Panel 4
KT-107 Tabletop Mount 6
KT-107 On-Wall Mount 8
Mounting the KT-107, KT-107RB 9
Mounting the KT-107 on a Table 9
Mounting the KT-107 on a Wall 14
Connecting Options 21
Setting up the KT-107, KT-107RB 22
Initial Setup 22
Additional KT-107 Important Functions 28
Upgrading the Firmware 31
Setup your PC for Firmware Upgrade 31
Install the RockChip Driver Assistant 31
Prepare the KT-107 for Firmware Upgrade 33
Upgrade the Firmware via PC 33
Technical Specifications 37
Kramer Electronics Ltd.
KT-107, KT-107RB - Introduction
1
Go to www.kramerav.com/downloads/KT-107 to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of
unique, creative, and affordable solutions to the vast range of problems that confront the video,
audio, presentation, and broadcasting professional on a daily basis. In recent years, we have
redesigned and upgraded most of our line, making the best even better!
Our 1,000-plus different models now appear in 14 groups that are clearly defined by function:
GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers; GROUP 3: Control
Systems; GROUP 4: Format/Standards Converters; GROUP 5: Range Extenders and
Repeaters; GROUP 6: Specialty AV Products; GROUP 7: Scan Converters and Scalers;
GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories
and Rack Adapters; GROUP 11: Sierra Video Products; GROUP 12: Digital Signage;
GROUP 13: Audio; and GROUP 14: Collaboration.
Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
Review the contents of this user manual.
Achieving the Best Performance
Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
Do not secure the cables in tight bundles or roll the slack into tight coils.
Avoid interference from neighbouring electrical appliances that may adversely influence
signal quality.
Position your Kramer KT-107 away from moisture, excessive sunlight and dust.
Kramer Electronics Ltd.
KT-107, KT-107RB - Introduction
2
Caution:
There are no operator serviceable parts inside the unit
Warning:
Use only the Kramer Electronics power supply that is provided with the unit
Warning:
Disconnect the power and unplug the unit from the wall before installing
KT-107RB Wi-Fi 5GHz frequency band range is restricted to up to 5.35GHz.
Safety Instructions (DC)
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling/.
Overview
Congratulations on purchasing your Kramer KT-107/KT-107RB Touch Panel.
Throughout this manual KT-107 refers to both KT-107 and KT-107RB, unless specified
otherwise.
KT-107 is a 7-inch IPS multi-touch, powerful Touch Panel with 1280x800 resolution. The
elegantly designed portable Touch Panel can be deployed either on a table or on the wall.
KT-107 supports wired Power over Ethernet (PoE) and advanced Wi-Fi connectivity options.
To ensure easy installation with elegant wiring and secured mounting, the Touch Panel
comes with table and wall mounts, a USB cable and a power supply unit.
The KT-107 is an Android-based Touch Panel that is ideal for any 24/7 Kramer-supported
commercial AV or control application and features a user-friendly, fully customizable graphical
user interface configured by Kramer software.
The KT-107 provides exceptional quality, advanced and user-friendly operation, and high-level
security options.
KT-107, KT-107RB - Introduction
3
Exceptional Quality
Elegant Design – Smooth integration with room furniture, either on tables or walls, with
flexible panel cabling and locking design options.
Superior User Experience – IPS 1280x800 high-resolution screen with ±85° horizontal and
vertical wide viewing angles, built-in lighting sensor for auto-adaptable brightness,
advanced 10 multi-touch points, and 2-finger gesture capabilities.
Powerful Processing – Quad-core CPU, GPU, 2GB RAM, 16GB ROM processing
performance for smoothly running complicated media- and graphics-rich applications,
encoding and decoding H.265 video and audio streams, and seamlessly operating the
high-resolution 2Mp HD front camera.
Flexible Services – Advanced Android 6.0 Operating System with rich Kramer and
market-available software applications offered via cloud/store, such as K-Touch Control.
Advanced and User-friendly Operation
Easy Installation – Powering and connectivity via a single Ethernet cable.
Kramer Electronics Ltd.
Flexible Mounting – Including table and wall mounts that fit into standard market-available
2 Gang in-wall junction boxes.
Optional Connectivity – Simple wireless BTLE 4.0 Bluetooth as well as connection to USB
peripheral devices for either table or wall-mount installations, using the included USB
cable.
Reliable Networking – Seamless switching between wired and wireless 802.11ac
connectivity.
Versatile Powering Options – PoE, PSU and battery.
Auto Sensing –Optimized performance and operation according to automatically detected
LAN speed.
Firmware Upgrade – Via USB port.
Security
Secured Deployment – Flexible locking options to prevent unwanted panel-mount removal,
elegantly designed to remain out of site.
Secured Operation – Highly secured operation of applications such as password protected
exit, hidden control buttons and so on. Red LED alert when camera is active.
Typical Applications
The KT-107 is ideal for the following typical applications:
Control user interface in meeting and conference rooms, boardrooms, and auditoriums.
Presentation of room scheduling.
Kramer Electronics Ltd.
KT-107, KT-107RB - Defining the KT-107, KT-107RB
4
#
Feature
Function
Hidden Reset Button
Located on top-side. Insert a pin and hold for a few seconds to reset
KT-107.
Light Sensor
Automatically adjusts the screen brightness according to the room
lighting conditions.
Activity RGB LED
Lights green when powered; flashes green when charging the
battery; lights red when camera is on.
Camera
For remote room viewing or video conferencing.
Microphone
For audio communication, recording or conferencing.
Speakers
To output the sound.
Control Button
Touch the Kramer logo area lightly to set the screen to sleep mode
or turn it back on.
Press and hold (for 1 to 2 seconds) to open the pop-up menu which
lets you power down the unit, reboot it or return to the Home-page.
Press twice to activate the camera.
Tabletop Mount Connector (on
the lower side)
For connecting to the tabletop mount (see Mounting the KT-107 on a
Table on page 9).
Defining the KT-107, KT-107RB
This section defines the KT-107 Touch Panel, the tabletop and the on-wall mounts.
KT-107 Touch Panel
This section defines the KT-107.
Figure 1: KT-107 Touch Panel Front and lower side Panel
Kramer Electronics Ltd.
KT-107, KT-107RB - Defining the KT-107, KT-107RB
5
#
Feature
Function
Cover
Covers the wall mount connections and power button.
Power Button
Press to power on the KT-107.
When powered, press briefly to open the pop-up menu and power down
the device, reboot it or return to the Home-page.
Press and hold to power down the device immediately.
This button is also used for firmware upgrade (see Upgrade the
Firmware via PC on page 33).
U Button
Used for firmware upgrade.
Press to increase KT-107 speaker volume.
Micro USB Port
For connecting to an adjacent on-wall USB device and for firmware
upgrade.
Flat Cable Connector
For connecting to the on-wall mount unit (see Mounting the KT-107 on a
Wall on page 14).
Connecting Holes
For connecting to the tabletop mount or the panel mount plate
To prevent potential damage to the Touch Panel, use only
Kramer supplied screws and mounts (see Mounting the KT-107
on a Table on page 9).
Figure 2: KT-107 Touch Panel Rear Panel
KT-107, KT-107RB - Defining the KT-107, KT-107RB
6
#
Feature
Function
Screw Openings (x2)
For attaching the Touch Panel to the tabletop mount using the supplied
M2x4 screws (see Mounting the KT-107 on a Table on page 9).
M5x60 Secure Screw
Opening
For safely securing the tabletop mount to the table from underneath (see
Figure 8).
KT-107 Tabletop Mount
This section defines the KT-107 tabletop mount.
Kramer Electronics Ltd.
Figure 3: Tabletop Mount Front View
Kramer Electronics Ltd.
KT-107, KT-107RB - Defining the KT-107, KT-107RB
7
#
Feature
Function
Micro USB Port
For connecting to an external USB device, such as a headset or a
memory disk.
Connect external devices only with the OTG type USB cable (supplied).
Regular USB cables (such as a smartphone data cable) can be used to
connect the device to a PC (for file transfer, and so on).
Power 2-pin Terminal Block
Connector
Connect to a power adapter and to the mains.
Cable Opening Knock-out
area
Cable pass-through area.
Screw Openings with Rubber
Covers (x2)
For covering the M2x4 screws that are used for attaching the KT-107 to
the tabletop mount (see Mounting the KT-107 on a Table on page 9).
Kensington Locker Port
For securely connecting the tabletop mount to a table with a
Kensington-compatible locker.
PoE Ethernet RJ-45 Port
Connect to the PoE-enabled Ethernet cable.
Cable Cover with Opening
Hides the ports and includes an opening for passing connected cables
over the table.
Solid Cable Cover
Hides the ports when passing connected cables under the table.
Figure 4: Tabletop Mount Rear View
KT-107, KT-107RB - Defining the KT-107, KT-107RB
8
#
Feature
Function
Groove (x4)
For hanging the panel mount plate (attached to KT-107) on a wall.
Flat Cable Connector
Connect to the rear side of the KT-107 using the supplied flat cable.
Passes the Ethernet signal and power to the KT-107.
Screw Opening (x8)
For attaching the on-wall mount unit to a standard in-wall junction box
(various holes fit different standard in-wall junction boxes), see Mounting the
KT-107 on a Wall on page 14.
Unit Cable Opening
Pass the supplied right-angle OTG USB cable through the opening to connect
to the rear side of the KT-107.
Indication Arrows
Top side up; shows the correct direction for mounting the on-wall mount unit
and for hanging the Touch Panel.
Screw Opening (x2)
For attaching the on-wall mount unit to a standard in-wall junction box
(various holes fit different standard in-wall junction boxes.
Indication Arrows
Top side up; shows the correct direction for hanging the panel mount plate.
Plate Cable Opening
Fits the opening on the on-wall mount unit. Pass the right-angle OTG USB
cable through the opening to connect to the rear side of the KT-107.
Screw opening (x4)
Attach the KT-107 to the panel mount plate using the supplied screws.
Cable opening
Pass the cables through the opening to connect to the rear side of the
KT-107.
Tab (x4)
For hanging the KT-107 with the attached panel mount plate on the on-wall
mount unit.
KT-107 On-Wall Mount
This section defines the KT-107 on-wall mount.
Kramer Electronics Ltd.
Figure 5: KT-107 Touch Panel Front Panel
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
9
Always be careful when attaching or removing the Touch Panel from either mounts.
To mount KT-107 in portable mode, go to Setting KT-107 on the Tabletop Mount on
page 12.
The thickness of the table should be 76.2mm (3”) or less.
Mounting the KT-107, KT-107RB
The KT-107 can be placed on a table or mounted on a wall.
Mounting the KT-107 on a Table
When mounting KT-107 on a table:
You can mount KT-107 either in secure mode or portable mode.
In secure mode, KT-107 is attached to the table (or other surface)
In portable mode, KT-107 is placed without damaging the table, is not secured and
can be moved.
The cables connected to KT-107 can be hidden by connecting them under the table via
the cable pass-through opening (in secure mode) or they can be connected over the table,
thus remaining visible (for both mounting modes).
Preparing the Table for a Secure Mount
When mounting KT-107 on a table in secure mode, prepare the table as follows:
Drill a hole in the table to fit the M5x60 screw used for securing the tabletop mount to the
table.
Cut an opening in the table if you need to pass the cables from underneath.
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
10
The cut-out dimensions in Figure 6 are not to scale.
Refer to the cut-out template available on the Kramer website at
www.kramerav.com/downloads/KT-107.
Kramer Electronics is not responsible for any damage caused to the table.
Take care not to damage the table. Kramer Electronics is not responsible for any damage
caused to the table.
Verify that the opening is correctly positioned in relation to the drilled M5x60 screw hole.
Use the following cutout drawing to correctly measure the location of the M5x60 screw hole
and the cable pass-through opening:
Figure 6: Cut-Out Dimensions
To drill the M5x60 screw hole in a table:
1. Measure the exact location on the surface of the table where you want to install the
KT-107.
2. Drill a hole in the table and cut the cable pass-through opening with a saw according to
the dimensions shown in Figure 6 (not to scale).
To cut the cable pass-through opening (if required):
1. Carefully measure the exact location of the cable pass-through opening.
2. Cut out the cable pass-through opening.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
11
Secure the Tabletop Mount
To secure the KT-107 tabletop mount:
1. Remove the rubber covers from the rear tabletop mount.
2. Remove the cable cover .
Kramer Electronics Ltd.
Figure 7: Removing Cable Cover and Rubber Screw Cover
3. Place the tabletop mount on the table.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
12
4. Insert the M5x60 screw through the M5x60 screw opening to secure the tabletop
mount to the table at the desired location.
5. Tighten the screw from under the table using an M5 Wing nut or a regular M5 nut.
Kramer Electronics Ltd.
Figure 8: Securing Tabletop Mount
Setting KT-107 on the Tabletop Mount
Before you begin, verify that the cable cover is removed.
To connect the cables and set the KT-107 on the tabletop mount:
1. Connect the RJ-45 port on the tabletop mount to the PoE-enabled network.
2. Connect the power adapter to the Power 2-pin terminal block connector on the
tabletop mount and to the mains power.
3. Place the KT-107 over the tabletop mount (the Touch Panel is magnetically held in
place), by first inserting the lower part of the Touch Panel then carefully laying the
KT-107 in place.
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
13
We recommend that you complete KT-107 setup (see Setting up the KT-107, KT-107RB, on
page 22) before securing the KT-107 to the tabletop mount.
Once setup is complete, carry on with the installation process.
4. Wait for the Home-page to load.
5. Secure the KT-107 to the tabletop mount using the two M2x4 screws (supplied) that are
inserted via the openings on the rear side of the tabletop mount.
6. Replace the rubber covers to hide the screws.
Figure 9: Connecting to the KT-107 Rear Panel
7. Connect the Ethernet and micro-USB cables by either passing the cables from
underneath the table via the cable opening (see Preparing the Table for a Secure Mount
on page 9), or by placing them over the table.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
14
Other popular in-wall mounting boxes may also be available in the market (such as the
GEWISS 4 Gang 144x85x50mm box (GW 24 404)).
8. Replace the appropriate cover (for under-the-table or over-the-table installation).
Kramer Electronics Ltd.
Figure 10: Replace the Cover
9. Optionally, lock the tabletop mount with a Kensington locker (not supplied).
Mounting the KT-107 on a Wall
KT-107 can be safely installed on a wall using standard 2 Gang in-wall junction boxes. The
cables are passed inside the wall and then connected to the rear side of the on-wall mount
unit.
Before mounting the KT-107 on a wall, you need to install a standard 2 Gang in-wall junction
box.
We recommend that you use any of the following standard 2 Gang in-wall junction boxes:
USA: 2 Gang electrical junction boxes.
Europe: 2 Gang in-wall junction box, 47mm minimum depth (DIN 49073).
UK: 2 Gang in-wall junction box, 137x75mm, 41mm minimum depth (BS 4662).
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
15
Inserting the On-Wall Mount Unit
To mount the on-wall mount unit:
1. Attach the on-wall mount unit to the installed in-wall junction box, (top side up, see the
indication arrows on the mount ).
2. Screw the 4 wall-mounting screws (supplied) through the screw openings .
The on-wall mount screw openings are set in different locations to fit various types of
in-wall junction boxes.
Kramer Electronics Ltd.
Figure 11: Installing the On-Wall Mount Unit
3. Optionally, insert the supplied right-angle OTG USB port if you need to connect the
KT-107 to an external USB device.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
16
Connecting the flat Cable
The flat cable passes power and PoE-enabled Ethernet to the Touch Panel.
To connect the flat cable:
1. On the rear side of the KT-107, unscrew the cover and set the cover and screw aside.
Kramer Electronics Ltd.
Figure 12: Removing the Cover on the KT-107 Rear Side
2. Attach the panel mount plate, top side up (see arrows), to the rear of the KT-107.
3. Fit the connecting holes on the KT-107 to the screw holes on the panel mount .
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
17
If you need to secure the KT-107 to the wall, use the Kramer KT-107-OWLK (purchased
separately).
For installation instructions, see Installing the On-Wall Secure Lock on page 19.
4. Insert the 4 M2x4 screws (supplied) and tighten.
Kramer Electronics Ltd.
Figure 13: Attaching the Panel Mount Plate to the Rear Side of the KT-107
5. Connect the flat cable between the on-wall mount and the KT-107.
Figure 14: Connecting the On-wall Mount Flat Cable
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
18
6. Hang the KT-107 on the wall by sliding the tabs on the attached panel mount plate
over the grooves on the on-wall mount unit.
Figure 15: Hanging KT-107 on the Wall
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
19
This example shows the short part on top and the long part below. You can attach it with the
long part on top and the short part below.
2. Place the short part (together with
the screws) over the installed
on-wall mount unit.
3. From below, slide the long frame
part towards the short frame part.
Figure 16: Placing the Frame Parts
Installing the On-Wall Secure Lock
The KT-107-OWLK, is purchased separately and secures KT-107 safely to the on-wall mount.
The On-Wall Lock includes a 2-part frame (short and long part),
2 screws and 2 washers.
To secure KT-107 to the on-wall mount:
1. Insert the 2 screws (supplied) into the screw openings and insert the washers from below.
Kramer Electronics Ltd.
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
20
4. Loosely screw the
top frame part to the
lower frame part (do
not tighten the
screws).
Figure 17: Screws Loose
5. After hanging the KT-107 on the
wall (Figure 14), tighten the two
screws until the KT-107 is
securely fixed in place.
Figure 18: Screws Tightened
KT-107, KT-107RB - Mounting the KT-107, KT-107RB
21
When both PoE and the power supply are connected to the Touch Panel, the unit is
powered by the power supply.
KT-107 features auto-sensing. It detects the speed of LAN devices (such as the LAN
(Ethernet) switch, the router and so on) connected to KT-107 and automatically sets the
KT-107 LAN port speed, accordingly.
For example:
If the LAN switch supports 100Mbps Fast Ethernet, the KT-107 LAN port is automatically
set to work at 100Mbps.
If the LAN switch supports 1000Mbps Gigabit Ethernet, the KT-107 LAN port is
automatically set to work at 1000Mbps.
Connecting Options
You can power the KT-107 using any or all of the following options:
Connect the PoE-enabled LAN RJ-45 connector to your local area PoE-enabled network.
Connect the power adapter to the 2-pin terminal block connector on the mount rear side.
Use the internal battery (after initially charging the battery for 8 hours).
Kramer Electronics Ltd.
Figure 19: Powering the KT-107 Touch Panel
Connect to the local area Ethernet network:
Via Ethernet cable connection to the LAN RJ-45 connector.
Use Wi-Fi if no wired Ethernet connection is available, or as a fall-back option.
Kramer Electronics Ltd.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
22
Setting up the KT-107, KT-107RB
Once the tabletop mount or in-wall installation is complete and power is connected, you can
slide the KT-107 in place and wait for the Home-page to sppear:
Figure 20: KT-107 Home-Page
Initial Setup
Following installation, use the Home-page Settings application to perform the following
initial setup tasks:
Setting the Date and Time on page 23.
Modifying the Display Settings on page 24.
Setting the Control Button on page 26.
Defining Home-page Password-protected Exit on page 27.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
23
Setting the Date and Time
To set the date and time:
1. In the Home-page, click Settings.
Kramer Electronics Ltd.
Figure 21: Settings – Date & Time
2. Scroll down to the System area and click Date & time.
Figure 22: Settings – Automatic Date & Time
3. Enable Automatic date & time to derive the date and time from the network.
If disabled, set the date and time manually.
4. Select the time format.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
24
Modifying the Display Settings
To modify Display Settings:
1. In the Home-page, click Settings.
Kramer Electronics Ltd.
2. Click Display.
Figure 23: Settings - Display
Figure 9: Settings – Display Setup
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
25
When enabled, the Touch Panel returns to the Home-page without displaying status bars.
Control Button Enabled
Control Button Disabled
Press the Control button . The Power/reset
pop-up screen appears (see Figure 24):
If Home-page Exit is not password
protected, switch to Home-page.
If Home-page Exit is password protected
(see Defining Home-page Password-
protected Exit on page 27), enter the correct
password and switch to Home-page.
Press rear-side power button .
Power/reset pop-up screen appears (see Figure 24).
Go to Home-page.
Or:
Click power-off and wait for system shut-down.
Press rear-side power button to power on. The Touch
Panel powers up.
Go to Home-page.
3. Define the following (as required):
Set the Brightness:
Brightness level.
Adaptive brightness – automatically adjusts the brightness level based on room
ambient room lighting.
Content Adaptive Brightness Control – automatically adjusts the brightness level
based on the displayed content.
Enable the camera activation shortcut via the control button – activate the “Press
control button twice for camera” feature.
Hide the bars (to prevent tampering with the Touch Panel):
Always hide the bottom status bar.
Always hide the top status bar.
Kramer Electronics Ltd.
Define display activity:
Sleep – set Touch Panel sleep timeout.
The following table defines how to access the Home-page when the bars are hidden, under
the following conditions: the Control button is enabled or disabled and the Touch Panel is or is
not password protected.
Kramer Electronics Ltd.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
26
Setting the Control Button
The KT-107 Control button is located under the Kramer logo and can be enabled via the
Settings application.
Use the Control button as follows:
Press briefly to enter the KT-107 sleep mode. When in sleep mode, press briefly to exit.
Press twice to activate the camera (if enabled via the Display Menu, see Modifying the
Display Settings on page 24)
Press for 1 to 2 seconds for the pop-up menu to appear and select Power off, Reboot or
Home-page.
Figure 24: Using a Hidden Control Button
When the Touch Panel is off, turn it on again via the power button on the rear side of the
Touch Panel.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
27
When the Control button is disabled, this option is disabled too.
To enable/disable the control button:
1. In the Home-page, click Settings.
2. Select Control.
Kramer Electronics Ltd.
Figure 25: Control Button Activation
3. Enable or disable the control button.
Defining Home-page Password-protected Exit
Password protection is used to prevent an unauthorized person from exiting an application
program.
To enable/disable password protection:
1. In the Home-page, click Settings.
2. Select Control.
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
28
The protected exit password is “KT-107go2home”.
3. Select Home-page password-protected exit to enable or disable this feature
(see Figure 25).
Kramer Electronics Ltd.
Figure 26: Password on Exit Settings
Additional KT-107 Important Functions
This section describes the following additional KT-107 functions:
About Touch Panel Page on page 29
Top Bar Functions on page 30
Lower Bar Functions on page 30
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
29
About Touch Panel Page
The About page summarizes all the Touch Panel information, such as system updates.
To view Touch Panel information:
1. In the Home-page, click Settings.
2. Scroll down and select About touch panel. The About touch panel screen appears:
Kramer Electronics Ltd.
Figure 27: About the KT-107 Touch Panel
KT-107, KT-107RB - Setting up the KT-107, KT-107RB
30
Top Bar Functions
The top bar displays various messages such as time and date, battery status and so on.
Kramer Electronics Ltd.
Lower Bar Functions
Use the lower bar functions as follows:
Figure 28: Top Bar Functions
Figure 29: KT-107 Lower Bar Functions
KT-107, KT-107RB - Upgrading the Firmware
31
The latest firmware version can be downloaded from the Kramer web site at
www.kramerav.com/downloads/KT-107.
DO NOT change the ‘Update.img’ file name.
If the ‘Rockchip_driverAssistant’ driver is already installed on your PC, skip this section and
proceed to Prepare the KT-107 for Firmware Upgrade on page 33.
If it is not installed or if you are unsure, complete the installation steps in this section.
Upgrading the Firmware
To upgrade the firmware:
Setup your PC for Firmware Upgrade, on page 31.
Install the RockChip Driver Assistant, on page 31.
Prepare the KT-107 for Firmware Upgrade, on page 33.
Upgrade the Firmware via PC, on page 33.
Setup your PC for Firmware Upgrade
Kramer Electronics Ltd.
To prepare the PC for upgrading the KT-107:
1. Download the firmware and FW-upgrade-tools zip files from the Kramer website at
www.kramerav.com/downloads/KT-107.
Verify that you are using the correct KT-107 or KT-107RB firmware file (according to
your device type).
The FW-upgrade-tools zip file includes both ‘Rockchip_DriverAssitant’ and ‘KT FW
Upgrade Tool’ upgrade tools.
2. Copy the ‘KT-107 Firmware Release xx’ (or ‘KT-107RB Firmware Release xx’), ‘FW
Upgrade Tool’ and ‘Rockchip_driverAssistant’ files and unzip them to local folders on your
PC.
Verify that the ‘KT-107 Firmware Release xx’ (or ‘KT-107RB Firmware Release xx’)
folder includes the ‘Update.img’ file for KT-107 or KT-107RB upgrade.
Install the RockChip Driver Assistant
To install the driver:
1. In the ‘Rockchip_driverAssistant’ folder, open ‘Driver Assistant’.
2. Double click ‘DriverInstall.exe’
KT-107, KT-107RB - Upgrading the Firmware
32
3. Click Run to install the ‘DriverInstall’ tool on your PC.
Figure 30: Installing the Driver
4. Click Install Driver.
The following window appears:
Kramer Electronics Ltd.
Figure 31: Driver Installation Security Note
5. Click Install repeatedly on the next few screens until the driver is successfully installed.
Figure 32: Successful Installation
6. Click OK.
KT-107, KT-107RB - Upgrading the Firmware
33
You can connect several Touch Panels to upgrade simultaneously.
Carefully place the KT-107 in a way that does not cause damage to the USB cable or port.
Prepare the KT-107 for Firmware Upgrade
To prepare the KT-107:
1. Verify that the battery is at least 70% charged.
2. Disconnect the panel from its mount (see Mounting the KT-107 on page 9).
3. Power-off the panel (from behind or via the Kramer control button on the front of
the Touch Panel).
4. Connect the PC USB port directly to the micro-USB port on the rear of the
KT-107 (do not use the port on the mount) via a USB cable with data-transfer-capabilities.
Kramer Electronics Ltd.
Upgrade the Firmware via PC
To upgrade the firmware:
1. In the ‘KT FW Upgrade Tool’ folder, double-click ‘Kramer Touch Panel FW Upgrade
Tool.exe’.
The FW Upgrade Tool window appears:
Figure 33: Firmware Upgrade Tool
Kramer Electronics Ltd.
KT-107, KT-107RB - Upgrading the Firmware
34
If you have connected more than one device, repeat steps 3 and 4 above for each USB
connected Touch Panel.
2. Click the … button next to the FW Path text box to select the path to the Update.img file
in the unzipped ‘KT-107 Firmware Release xx’ folder.
Figure 34: Update File Loaded
3. Press the Touch Panel Control Button of the first USB-connected panel for
approximately 2 seconds and turn the power off (see Setting the Control Button on page
26).
4. On the rear side of of the Touch Panel, press the Volume-up button together with the
Power button for a few seconds until the ON front panel LED dimly lights green
and the ‘1’ indication in the Connected Devices area of the FW Upgrade Tool window
shows that the device is connected to the PC (turns green).
Kramer Electronics Ltd.
KT-107, KT-107RB - Upgrading the Firmware
35
If the connection process fails, press and hold the Power button until the unit powers
down and then restart the FW upgrade process.
Figure 35: Touch Panel Connected to PC
5. Click Upgrade (after all the Connected Devices icons turn green). The upgrade progress
is displayed:
Figure 36: Firmware Upgrade Progress
KT-107, KT-107RB - Upgrading the Firmware
36
6. Wait for the green “Success” message to appear:
Kramer Electronics Ltd.
Figure 37: Firmware Upgrade Complete
Following successful firmware installation, wait for the Touch Panel to power up. This process
may take a few minutes.
KT-107, KT-107RB - Technical Specifications
37
Tabletop Mount Ports:
1 1000/100/10BaseT Ethernet on RJ-45 connector
1 micro USB 2.0
1 2-pin terminal block for DC power supply
On-wall Mount Ports:
1 1000/100/10BaseT Ethernet on RJ-45 connector
1 2-pin terminal block for DC power supply
Speakers:
2x1 W, 8 ohm
Microphone:
-42dB ±3dB @ 1kHz sensitivity
CPU Performance:
1.6GHz Quad Core, GPU, 2GB RAM, 16GB Flash
OS Software:
Android 6.0.1
Multi Touch:
10 points, 2-finger gesture
Display:
7” IPS, 1280x800 RGB pixels, 16:10 aspect ratio, ±85° horizontal/vertical
viewing angles, 400cd/m2 brightness, 800:1 contrast ratio
Video Format:
Decoding: H.265/HEVC; H.264/AVC; MPEG-1/2/4; DivX 3/4/5/6; MVC;
GOOGLE VP8; VC-1; H.263; SORENSON SPARK; ON2 VP6; MOTION
JPEG
Encoding:H.264/AVC
Ethernet Port:
Auto-sensing 10/100/1000Mbps PoE LAN
Wireless Communication:
Wi-Fi 802.11 b/g/n/ac, Bluetooth 4.0
For KT-107RB, Wi-Fi 802.11 ac, 5GHz frequency band range is
restricted to up to 5.35GHz
Camera:
Front, 2M pixels, HD 720p
Battery:
Rechargeable, supports up to 3 hours of Wi-Fi operation
Controls:
Hidden reset button, power button, volume-up button
Touch panel status LED: flashes green during charging, steady green for
fully charged, red for camera on
Power Inputs:
Power over Ethernet (complies with IEEE802.3af and IEEE802.3at PoE
standards), power supply unit
Power Consumption:
5V DC, 3A
Operating Temperature:
0° to +40°C (32° to 104°F)
Storage Temperature:
-10° to +55°C (14° to 131°F)
Humidity:
10% to 90%, RHL non-condensing
Case Design:
Black body and cover
Certifications:
CE/CB, FCC, ROHS, REACH
Dimensions:
Shipping dimensions:22.4cm x 13cm x 20.6cm (8.8" x 5.12" x 8.1"), W, D, H
Touch panel: 17.8cm x 1.3cm x 13cm (7" x 0.51" x 5.12"), W, D, H
Tabletop mount: 18.5cm x 10.7cm x 12.4cm (7.28" x 4.2" x 4.88"), W, D, H
Panel mount plate: 14.6cm x 3.7cm x 9.2cm (5.75" x 1.46" x 3.62"), W, D, H
On-wall mount unit: 14.6cm x 1.1cm x 9.1cm (5.75" x 0.43" x 3.58"), W, D, H
Weight:
Shipping weight: 1.8kg (3.97lbs) approx.
Touch panel: 0.37kg (0.8lbs) approx.
Mounting Options:
Table top (with mount unit), on-wall (with mount unit and panel mount plate)
Included Accessories:
Power supply unit adapter (5V, 4.0A AC/DC), tabletop mount, on-wall mount
unit, panel-mount plate, right-angle OTG USB cable, installation screws
Options:
On-wall security lock (KT-107-OWLK)
Specifications are subject to change without notice at www.kramerav.com
Technical Specifications
Kramer Electronics Ltd.
Limited Warranty
The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:
What is Covered
This limited warranty covers defects in materials and workmanship in this product.
What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use
or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to
the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting from
the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone
unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship
of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the
technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other
product or technology with which the product may be used.
How Long this Coverage Lasts
The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:
1. All Kramer VIA products are covered by a standard three (3) year warranty for VIA hardware and a standard one (1) year warranty for
firmware and software updates. (An extended software warranty plan for an additional 2 years can be purchased separately).
2. All Kramer fiber optic cables and adapters, all Kramer speakers and Kramer touch panels are covered by a standard one (1) year warranty.
3. All Kramer Cobra products, all Kramer Calibre products, and all Kramer Minicom digital signage products are covered by a standard three (3)
year warranty.
4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.
5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for
three (3) years).
6. K-Touch software is covered by a standard one (1) year warranty for software updates.
Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or
owners of this product.
What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim
under this limited warranty:
1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and
labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs
necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same
function as the original product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought
under this limited warranty.
What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned
uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or reinstallation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any
adjustment of user controls or any programming required for a specific installation of this product.
How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this
product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service
providers, visit our web site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer
Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be
required (RMA number). You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original carton,
for shipping. Cartons not bearing a return authorization number will be refused.
Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE
PRICE PAID FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR
DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR
UNDER ANY OTHER LEGAL THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental,
consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.
Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE
MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER
ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED
WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY
ACT (15 U.S.C.A. §2301, ET SEQ.) OR OTHER APPICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY
TO YOU, AND ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE
PARTICULAR PURPOSE, SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.
Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by
Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an
authorized Kramer Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this
document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the
online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of
satisfaction.
P/N:
2900-300696
Rev:
1
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this
user manual may be found.
We welcome your questions, comments, and feedback.
www.kramerAV.com
info@kramerel.com
Loading...