Kramer KDS-EN5, KDS-DEC5 User Manual

P/N: 2900-300906 Rev 1 www.kramerAV.com

USER MANUAL

MODEL:

KDS-EN5, KDS-DEC5
H.264 Encoder and Decoder

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Contents

i

Contents

Introduction 1

Getting Started 1
Overview 2
Typical Applications 2

Defining KDS-EN5, KDS-DEC5 H.264 Encoder and Decoder 4
Installing KDS-EN5, KDS-DEC5 5
Connecting KDS-EN5, KDS-DEC5 6
Operating KDS-EN5, KDS-DEC5 8
Configuring Settings 9

Configuring Streaming/Encoding Settings 10
Configuring Decoding Settings 14
Configuring Network Settings 15
Locating Device 16
Configuring RS-232 over IP Settings 17
Changing the Device DNS Name 18
Upgrading the Firmware 19
Changing Password 20
Configuring Video Wall 21
Defining an Idle Image 22
Verifying Device Information 23

Technical Specifications 24

Default Communication Parameters 25
Resetting the Unit 26

Protocol 3000 27

Understanding Protocol 3000 28
Kramer Protocol 3000 Syntax 28
Protocol 3000 Commands 30

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Introduction

1

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing
a world of unique, creative, and affordable solutions to the vast range of problems that
confront the video, audio, presentation, and broadcasting professional on a daily
basis. In recent years, we have redesigned and upgraded most of our line, making the
best even better!

Getting Started

We recommend that you:

• Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment.

• Review the contents of this user manual.

Go to www.kramerav.com/downloads/KDS-EN5 to check for up-to-date user
manuals, application programs, and to check if firmware upgrades are available
(where appropriate).

Achieving the Best Performance

• Use only good quality connection cables (we recommend Kramer high­performance, high-resolution cables) to avoid interference, deterioration in signal
quality due to poor matching, and elevated noise levels (often associated with
low quality cables).

• Do not secure the cables in tight bundles or roll the slack into tight coils.

• Avoid interference from neighboring electrical appliances that may adversely

influence signal quality.

• Position your Kramer KDS-EN5, KDS-DEC5 away from moisture, excessive
sunlight and dust.

This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.

Safety Instructions

Caution: There are no operator serviceable parts inside the unit.
Warning: Use only the Kramer Electronics power supply that is provided with the unit.
Warning: Disconnect the power and unplug the unit from the wall before installing.

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to
reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Introduction

2

to be collected and recycled. To comply with the WEEE Directive, Kramer Electronics
has made arrangements with the European Advanced Recycling Network (EARN)
and will cover any costs of treatment, recycling and recovery of waste Kramer

Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s

recycling arrangements in your particular country go to our recycling pages at

www.kramerav.com/support/recycling.

Overview

Congratulations on purchasing your Kramer KDS-EN5, KDS-DEC5 H.264 Encoder

and Decoder. KDS-EN5, KDS-DEC5 are an H.264 encoder/decoder pair for HDMITM

signals of up to 4K@30Hz (4:4:4). They provide high-quality and fully-featured end-to­end video and audio over IP. KDS-EN5 and KDS-DEC5 include AVC support for
H.264/MPEG-4 and AAC codec, open encoding that enables decoding through VLC®
player software and unicast or multicast streaming through TS and RTSP transport
protocols.

Benefits and Features

• High Resolution Video Encoding and Compression – supporting up to 4K@30Hz
(4:4:4) resolution.

• Maximum Compatibility – Fully standard and compliant H.264/MPEG-4 AVC
(Advanced Video Codec) and AAC (Advanced Audio Code) codecs, enable
compatibility with other software and hardware encoders. Open encoding enables
software decoding through VLC® player software.

• Versatile Powering Options - Powered by PoE (when using a Network switch that
supports PoE) or by external 12V power adapter.

• Standard Ethernet Network Operation – 10/100/1000Mb. Managed switch: 1G,
multicast, IGMP snooping, layer 2. Configurable DHCP, Static or Auto IP.
For specific Network configuration, please contact Kramer Customer Support.

• Selectable Streaming Mode – Unicast or multicast through RTSP (Real Time
Streaming Protocol).

• Convenient Unit Control and Configuration – Distance control via user-friendly
embedded web pages via the Ethernet, Protocol 3000 API, and RS-232 serial
commands transmitted by a PC, touch screen system or other serial controller.

• Cost-Effective Maintenance - Power and link status indicators facilitate easy local
maintenance and troubleshooting. Firmware upgrade via embedded web pages
or K-Upload ensures lasting, field-proven deployment.

• Simple System Management — Remote system management support to enable
quick and efficient remote system and device life–cycle management.

Typical Applications

KDS-EN5, KDS-DEC5 is ideal for the following typical applications:

• Digital signage

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Introduction

3

• Video walls

• Education

• Smart city CCTV

• Large AV Matrixes

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Defining KDS-EN5, KDS-DEC5 H.264 Encoder and Decoder

4

Defining KDS-EN5, KDS-DEC5 H.264 Encoder and Decoder

This section defines KDS-EN5, KDS-DEC5.

Figure 1: KDS-EN5 Video Streamer Encoder

Figure 2: KDS-DEC5 Video Streamer Decoder

#

Feature

Function

POWER LED Indicator

Lights when the unit is powered on.

STATUS LED Indicator

KDS-EN5 – Lights when synced with a decoder.
KDS-DEC5 – Blinks slowly when not synced with an encoder.

Lights when synced with an encoder.

ID Button (KDS-DEC5)

Press to display the encoder and decoder information, such as device IP
address and ID, on the display.

DC 12V Connector

Connect to a 12V power adapter (optional – when power is not supplied
by PoE).

LAN (POE) RJ-45
Connector

Connect to a PC via a LAN to control the unit, to stream video to the unit
and to provide power via PoE.

AUDIO OUT 3-pin Terminal
Block

Connect to an unbalanced audio acceptor.

HDMI IN (KDS-EN5) / OUT
(KDS-DEC5) Connector

Connect to an HDMI source/acceptor.

RS-232 3-pin Terminal
Block Connector

Connect to an external device (e.g. a camera or display screen) that can
be controlled via RS-232 (over IP).

RESET Button

Press and hold for about 15 seconds to reset to factory default settings.

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Installing KDS-EN5, KDS-DEC5

5

Installing KDS-EN5, KDS-DEC5

This section provides instructions for mounting KDS-EN5, KDS-DEC5. Before
installing, verify that the environment is within the recommended range:

• Operation temperature – 0 to 40C (32 to 104F).

• Storage temperature – -40 to +70C (-40 to +158F).

• Humidity – 10% to 90%, RHL non-condensing.

When installing, avoid hazards by taking care that:

• It is located within recommended environmental conditions. Operating
ambient temperature of a closed or multi-unit rack assembly may exceed
ambient room temperature.

• Once mounted, there is enough air flow around KDS-EN5, KDS-DEC5.

• KDS-EN5, KDS-DEC5 is placed upright in the correct horizontal

position.

Always mount KDS-EN5, KDS-DEC5 before connecting any cables or power.

You can install KDS-EN5, KDS-DEC5 using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

• Fasten a bracket (included) on each side of the unit and attach it to a flat surface.

For more information go to www.kramerav.com/downloads/KDS-EN5.

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Connecting KDS-EN5, KDS-DEC5

6

Connecting KDS-EN5, KDS-DEC5

Always switch off the power to each device before connecting it to your KDS-EN5,

KDS-DEC5. After connecting your KDS-EN5, KDS-DEC5, connect its power and

then switch on the power to each device.

Figure 3: Connecting to the KDS-EN5, KDS-DEC5 Rear Panel

To connect KDS-EN5, KDS-DEC5 as illustrated in Figure 3:

1. Connect the LAN (POE) RJ-45 Connector on each unit to the LAN
OR
Connect the units directly via the LAN (POE) RJ-45 Connector on each unit
using an Ethernet cable.

2. On KDS-EN5, connect an HDMI video source (for example, Blu-ray player) to:

▪ HDMI IN Connector .
▪ RS-232 3-pin Terminal Block Connector for controlling the source via the

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Connecting KDS-EN5, KDS-DEC5

7

IP controller SW / API.S.

3. On KDS-DEC5, connect the HDMI acceptor (for example, TV) to:

▪ HDMI OUT Connector .
▪ RS-232 3-pin Terminal Block Connector for controlling the acceptor via the

IP controller SW / API.S.

4. Connect the video source

5. If desired, connect an audio amplifier to the AUDIO OUT 3-pin Terminal Block
on one or both units.

6. If PoE is not available, connect a 12V power supply (not included) to the DC 12V
Connector .

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Operating KDS-EN5, KDS-DEC5

8

Operating KDS-EN5, KDS-DEC5

Configure and control your KDS-EN5, KDS-DEC5 using any of the following methods:

• Via the Ethernet using built-in, user-friendly web pages (see Configuring Settings
on page 9).

• Kramer Network Enterprise Management Platform (version 2.2 or higher – go to

www.kramerav.com/product/Kramer Network for more information).

• Protocol 3000 commands (see Protocol 3000 Commands on page 30).

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Configuring Settings

9

Configuring Settings

The embedded web pages enable you to configure KDS-EN5, KDS-DEC5 via
Ethernet. The encoder and decoder each have their own web pages that are
accessed using a web browser on a connected computer.

KDS-EN5, KDS-DEC5 web pages enable performing the following:

• Configuring Streaming/Encoding Settings on page 10.

• Configuring Decoding Settings on page 14.

• Configuring Network Settings on page 15.

• Locating Device on page 16.

• Configuring RS-232 over IP Settings on page 17.

• Changing the Device DNS Name on page 18.

• Upgrading the Firmware on page 19.

• Changing Password on page 20.

• Configuring Video Wall on page 21.

• Defining an Idle Image on page 22.

• Verifying Device Information on page 23.

To browse KDS-EN5, KDS-DEC5 web pages:

1. Type the IP address of the device in the address bar of your internet browser
(default encoder address = 192.168.1.39, default decoder address =

192.168.1.40).
The Login page appears.

Figure 4: Embedded Web Pages Login Page

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Configuring Settings

10

2. Enter the password (default = admin) and click Login.
The embedded web pages appear with the System page open.

Figure 5: Embedded Web Pages – System Page

3. Navigate to the desired tab by clicking the web page from the main menu and the
tab from the submenu.

After changing a setting, click Apply to save the setting.
A message appears in the upper right corner of the web page indicating if the change

was successful or not.

Figure 6: Embedded Web Pages with Operation Successful Message

Configuring Streaming/Encoding Settings

KDS-EN5 web pages enable you to configure streaming/encoding settings.

This section applies only to the encoder web pages.

Kramer Electronics Ltd.

KDS-EN5, KDS-DEC5 – Configuring Settings

11

To configure streaming/encoding settings:

1. On the KDS-EN5 web pages, click Function > Stream Settings.
The Streaming Settings tab appears.

Figure 7: Function > Steam Settings Tab

2. Under Stream Video Over IP, select Enable.

3. Under Transport Type, select one of the following:

▪ tsoverudp – use Transport Stream over UDP protocol
▪ tsovertcp – use Transport Stream over TCP protocol

4. If required, under Rate Limit Enable, select Enable, to limit the bitrate.

You can set the limit value in the Video Settings tab.

5. Click Video Settings.