Kramer KDOCK-4-HOLDER Installation Instructions

Page 1
www.kramerAV.com info@kramerel.com
Installation Instructions
MODEL:
P/N:
290 0 - 301 5 22QS
Rev:
3
SAFETY WARNING Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to these installation instructions may be found. We welcome your questions, comments, and feedback.
Page 2
2
KDOCK-1/2/3-HOLDER
KDOCK-1/2/3-HOLDER
Congratulations on purchasing your Kramer KDOCK-1/2/3-HOLDER / KDOCK-4-HOLDER for safely securing KDock USB-C Hub Multiport Adapters below or on a surface.
This document describes how to secure the KDOCK-1/2/3-HOLDER and the
KDOCK-4-HOLDER to a surface.

Installing the KDOCK-1/2/3-HOLDER

KDOCK-1/2/3-HOLDER can be installed either under or above a surface. In this example,
it is installed under a table.
To secure the KDOCK-1/2/3-HOLDER under a table:
1. Insert the KDock device into the clamp, in-between the rubber pads.
2. Insert a washer (supplied) and then a nut (supplied) onto each of the studs and tighten.
3. Check the location under the table where you want to install the device and mark the location for the two installation screws (supplied).
4. Use the two installation screws to secure the KDOCK-1/2/3-HOLDER under the table.
KDOCK-1/2/3-HOLDER is secured under a table.
Page 3
Installation Instructions
3

Installing the KDOCK-4-HOLDER

KDOCK-4-HOLDER can be installed either under or above a surface. In this example, it is
installed on a table. Note that when it is installed under, the flip-up device holder cannot be used.
To secure the KDOCK-4-HOLDER on a table:
1. Place the KDock-4 device on the surface, at the correct location.
2. Place the KDOCK-4-HOLDER over the device.
3. Insert the four screws and secure the KDOCK-4-HOLDER to the table.
KDOCK-4-HOLDER is secured on a table.
Page 4
4
KDOCK-1/2/3-HOLDER

Technical Specifications

Environmental Conditions
Operating Temperature
0° to +40°C (32° to 104°F).
Storage Temperature
-10° to +55°C (14° to 131°F).
Humidity
5% to 90%, RHL non-condensing.
Regulatory Compliance
Safety
CE.
Environmental
RoHs
Enclosure
Materials
Zinc-coated steel and rubber padding (for
KDOCK-1/2/3-HOLDER only)
General
Net Dimensions (W, D, H)
KDOCK-1/2/3-HOLDER: 3cm x 6.5cm x 1.9 cm
(1.2" x 2.6" x 0.75") Approx.
KDOCK-4-HOLDER: 26.2cm x 7.1cm x 2.5cm
(10.3" x 2.8" x 1") Approx.
Shipping Dimensions (W, D, H)
KDOCK-1/2/3-HOLDER: 12.1cm x 8.2cm x 4.1cm
(4.8" x 3.2" x 1.6")
KDOCK-4-HOLDER: 36.6cm x 21cm x 7.7 cm
(14.4" x 8.27" x 3")
Net Weight
KDOCK-1/2/3-HOLDER: 50g (0.11lbs) approx. KDOCK-4-HOLDER: 201g (0.44lbs) approx.
Shipping Weight
KDOCK-1/2/3-HOLDER: 90g (0.2lbs) approx. KDOCK-4-HOLDER: 261g (0.6lbs) approx.
Loading...