Page 1
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 1
mITX-KBL - QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron mITX-KBL embedded board. This document provides information to allow you to quickly
install this product.
Packing Checklist
1. Take the mITX-KBL out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
mITX-KBL main board
Rear I/O Shield
COM Port Cable*
DIO Cable*
USB 3.0 Cable*
2-Port USB 2.0 Cable*
SATA Cable*
PS/2 Cable*
VGA Cable*
3G Mini SIM Card Holder Kit*
Page 2
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 2
Jumper and Internal Connector Locations
Jumper List
Item
Designation
Description
1
JP1
AT / ATX Power Mode Selection
2
JP2
Clear ME Register
3
JP3
RTC Reset Selection
4
JP4
mPCIE / mSATA Selection for MPCIE1 (models w/ Q170 only)
5
JP5
mPCIE / mSATA Selection for MPCIE2 (models w/ Q170 only)
6
JP6
Keyboard Lock Selection
7
JP7
mPCIE LED Indicator Pin Header
8
JP9
PCIE Configuration Setting for PEG1 (models w/ Q170 only)
9
JP10
Backlight Power Enable Selection for LVDS1
10
JP11
Panel & Backlight Power Selection for LVDS1
11
JP12
Pin-9 Selection for COM1
12
JP13
ME F/W Selection
13
JP14
Pin-9 Selection for COM2
7 8 9
11
10
13
14
15
16
18
19 4 20
22
21
23
24
25
27
28
12
30
29
31
32
33
34
35
17
37
38
39
43
6
42
5
41
3
40
2
36
1
44
45
46
26
Page 3
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 3
Internal Connector List
Item
Designation
Description
14
ATX1
2x12-pin ATX Power Supply Wafer
15
ATX2
2x2-pin ATX Power Supply Wafer
16
BAT1
CR2032 Battery Power Input Wafer
17
CN1
USB3.0 Port-5, 6 Box Header (models w/ Q170 only)
18
CN2
SIM Interface Wafer for MPCIE2
19
CN3
USB2.0 Port 11, 12 Pin Header (models w/ Q170 only)
20
CN4
USB2.0 Port 7, 8 Pin Header
21
CN5
8-bit Digital Input / Output Pin Header
22
CN6
RS-232 / 422 / 485 Port 3 Wafer
23
CN7
RS-232 Port 4 Wafer
24
CN8
RS-232 Port 5 Wafer
25
CN9
RS-232 Port 6 Wafer
26
CN10
VGA Header
27
CN11
Left Channel 3W Audio AMP Output Wafer
28
CN12
Backlight Power Output Wafer for LVDS1
29
CN13
Front Panel Audio Pin Header
30
CN14
SPDIF-Out Pin Header
31
CN15
PS/2 Keyboard & Mouse Mini-DIN Connector
32
CN16
Right Channel 3W Audio AMP Output Wafer
33
FAN1
CPU FAN Wafer
34
FAN2
System FAN Wafer
35
FP1
Front Panel Pin Header 1
36
FP2
Front Panel Pin Header 2
37
MPCIE1
Half Size mPCIE / mSATA Socket
38
MPCIE2
Full Size mPCIE / mSATA Socket
39
PEG1
PCIEx16 Slot
40
SATA1
Serial ATA Port-0 Connector
41
SATA2
Serial ATA Port-1 Connector
42
SATA3
Serial ATA Port-2 Connector
43
SATA4
Serial ATA Port-3 Connector
44
DIMM1
DDR4 Memory SO-DIMM Socket
45
DIMM2
DDR4 Memory SO-DIMM Socket
46
LVDS1
Primary 24-bit, 2-channel LVDS Panel Connector
Page 4
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 4
Jumper Settings
AT / ATX Power Mode Selection (JP1)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - ATX Mode
- X AT Mode
“X” = Jumper set (short) and “-” = jumper not set (open)
Clear ME Register (JP2)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - Normal
- X Clear ME Register
“X” = Jumper set (short) and “-” = jumper not set (open)
RTC Reset Selection (JP3)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - Normal (default position)
- X Clear RTC CMOS (board does not boot with the jumper in this position)
“X” = Jumper set (short) and “-” = jumper not set (open)
2
3
1
2
3
1
2
3
1
Page 5
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 5
mPCIE / mSATA Selection for MPCIE2 (JP4) (only for models with Intel® Q170 Chipset)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - mSATA
- X mPCIE
“X” = Jumper set (short) and “-” = jumper not set (open)
mPCIE / mSATA Selection for MPCIE1 (JP5) (only for models with Intel® Q170 Chipset)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - mSATA
- X mPCIE
“X” = Jumper set (short) and “-” = jumper not set (open)
Keyboard Lock Selection (JP6)
Jumper 1 Position
Description
Pin 1-2
Pin 2-3
X - Normal
- X Keyboard Locked
“X” = Jumper set (short) and “-” = jumper not set (open)
2
3
1
2
3
1
2
3
1
Page 6
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 6
MPCIE LED Indication Pin Header (JP7)
Pin
Signal
Note
1
LED+
2 LED-
Panel & Backlight Power Selection for PEG1 (JP9) (only for models with Intel® Q170 Chipset)
Jumper Position
Description
Pin 1-3
Pin 3-5
Pin 2-4
Pin 4-6
X - X - x16 - X X -
x8 x8
“X” = Jumper set (short) and “-” = jumper not set (open)
Backlight Power Enable Selection for LVDS1 (JP10)
Jumper 1 Position
Description
Pin 1-3
Pin 3-5
X - Backlight Enable Voltage = +3.3V
- X Backlight Enable Voltage = +5V
Jumper 2 Position
Description
Pin 2-4
Pin 4-6
X - Active High
- X Active Low
“X” = Jumper set (short) and “-” = jumper not set (open)
1
2
21
65
21
65
Page 7
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 7
Panel & Backlight Power Selection for LVDS1 (JP11)
Jumper 1 Position
Description
Pin 1-3
Pin 3-5
X - Backlight Power = +12V
- X Backlight Power = +5V
Jumper 2 Position
Description
Pin 2-4
Pin 4-6
X - Panel Power = +3.3V
- X Panel Power = +5V
“X” = Jumper set (short) and “-” = jumper not set (open)
Pin-9 Selection for COM1 (JP12)
Jumper Position
Description
Pin 1-2
Pin 2-3
Pin 3-4
Pin 4-5
X - - - COM1, Pin-9 = +12V
- X - - COM1, Pin-9 = +5V
- - X - COM1, Pin-9 = +5V
- - - X COM1, Pin-9 = RI
“X” = Jumper set (short) and “-” = jumper not set (open)
ME F/W Selection (JP13)
Jumper Position
Description
Pin 1-2
X
Security Measures Defined by BIOS are Over-written
-
Security Measures Defined are Set
“X” = Jumper set (short) and “-” = jumper not set (open)
21
65
Page 8
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 8
Pin-9 Selection for COM2 (JP14)
Jumper Position
Description
Pin 1-2
Pin 2-3
Pin 3-4
Pin 4-5
X - - - COM1, Pin-9 = +12V
- X - - COM1, Pin-9 = +5V
- - X - COM1, Pin-9 = +5V
- - - X COM1, Pin-9 = RI
“X” = Jumper set (short) and “-” = jumper not set (open)
Page 9
mITX-KBL - Quick Installation Guide - Version 1.0 // www.kontron.com // 9
Real I/O Panel Connector Locations
Item
Designation
Description
1
CN17
GbE LAN1 & USB3.0 Port-1, 2 Connector
2
CN18
GbE LAN2 & USB3.0 Port-3, 4 Connector
3
CN19
DVI-D Connector
4
CN20
Line-In, Line-Out & Mic-In Audio Jacks
5
CN21
USB2.0 Port-9, 10
6
CN22TOP
RS-232 / 422 / 485 COM2 Connector
7
CN22BOT
RS-232 / 422 / 485 COM1 Connector
8
CN23
Display Port B Connector
9
CN24
Display Port A Connector
1 7 5 9 8 2 3 4 6
Loading...