APPENDIX A: REVISION HISTORY ...................................................................................8
Page 3
KAB-ADAPT-LVDStoTTL
1
1. User Information
1.1 About This Document
This document provides information about products from Kontron Embedded Modules GmbH and/or its
subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every attempt has been
made to ensure that the information in this document is accurate, the information contained within is
supplied “as-is” and is subject to change without notice.
For the circuits, descriptions and tables indicated, Kontron assumes no responsibility as far as patents
or other rights of third parties are concerned.
All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form or by any means
(electronic, mechanical, photocopying, recording, or otherwise), without the express written
permission of Kontron Embedded Modules GmbH.
DIMM-PC®, PISA®, ETX®, ETXexpress® , X-board®, DIMM-IO® and DIMM-BUS® are trademarks or registered trademarks of Kontron Embedded Modules GmbH. Kontron is trademark or registered
trademark of Kontron AG.
1.3 Trademarks
The following lists the trademarks of components used in this board.
ä
ä
ä
ä
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business
Machines Corp.
Microsoft is a registered trademark of Microsoft Corp.
Intel is a registered trademark of Intel Corp.
All other products and trademarks mentioned in this manual are trademarks of
their respective owners.
1.4 Standards
Kontron Embedded Modules GmbH is certified to ISO 9000 standards.
Page 4
KAB-ADAPT-LVDStoTTL
2
1.5 Warranty
This Kontron Embedded Modules GmbH product is warranted against defects in material and
workmanship for the warranty period from the date of shipment. During the warranty period, Kontron
Embedded Modules GmbH will at its discretion decide to repair or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
speci- fications or improper installation or maintenance.
Kontron Embedded Modules GmbH will not be responsible for any defects or damages to other products
not supplied by Kontron Embedded Modules GmbH that are caused by a faulty Kontron Embedded
Modules GmbH product.
1.6 Technical Support
Technicians and engineers from Kontron Embedded Modules GmbH and/or its subsidiaries are available
for technical support. We are committed to making our product easy to use and will help you use our
products in your systems.
Before contacting Kontron Embedded Modules GmbH technical support, please consult our Web site at
www.kontron.com/FPC for the latest product documentation, utilities, and drivers. If the information
does not help solve the problem, contact us by telephone or email.
KAB-ADAPT-LVDStoTTL is converter from JILI30 interface to FELX32 System. KAB-ADAPT-LVDStoTTL is
used to connect VGA/SVGA panels to Kontron Embedded Modules flat panel controllers (aFLAT-, uFLAT-,
new MOPS-Series) with JILI30 interface.
2.2 FLEX32 Family
FLEX32 is a Kontron hardware standard that interfaces the host computer system via TTL (18-Bit) to
flat-panel displays.
2.3 JILI30 Family
JILI30 (Jumptec Intelligent LVDS Interface) is a Kontron hardware standard that interfaces the host
computer system via LVDS to flat-panel displays. The target displays are usually medium- to highresolution TFT displays with parallel (CMOS, non-LVDS) interfaces.
3. Specifications
3.1 Mechanical Specifications
3.1.1 Cable lengthens
ä
3.1.2 Module Dimensions (PCB)
ä
3.1.3 Weight
ä
300mm ±10mm
45x 35 mm
20 g
Page 6
KAB-ADAPT-LVDStoTTL
4
3.2 Electrical Specifications
3.2.1 Supply Voltage
ä
5 V DC ±5%
3.2.2 Supply Voltage
ä
500 mV peak to peak 0 – 20 MHz
3.2.3 Supply Current
ä
See Datasheet from Panel
3.2.4 Panel Current
ä
Maximum curent: 600mA
3.3 Environmental Specifications
3.3.1 Temperature
4. Operating (with appropriate airflow):
•Maximum operating temperature: 0 to +60 °C
(*)
5.Non operating: -10 to +85 °°°°C
Note:
5.1.1Humidity
(*) The maximum operating temperature is the maximum measurable temperature on any spot on a
mo- dule’s surface. You must maintain the temperature according to the above specification.
ä
ä
Operating: 10% to 90% (non condensing)
Non operating: 5% to 95% (non condensing)
Page 7
KAB-FLEX32-TSDD10
5
6. Connector
6.1 FLEX32 Contacts.
Flatfoil connector, Right Angle, Bottom Contact
Pin Signal Name Function
1 GND Power Gound
2 DCLK Data Clock
3 LP Latch Pulse
4 FLM First Line Marker
5 GND Power Gound
6 R0 Panel Data R0
7 R1 Panel Data R1
8 R2 Panel Data R2
9 R3 Panel Data R3
10 R4 Panel Data R4
11 R5 Panel Data R5
12 GND Power Gound
13 G0 Panel Data G0
14 G1 Panel Data G1
15 G2 Panel Data G2
16 G3 Panel Data G3
17 G4 Panel Data G4
18 G5 Panel Data G5
19 GND Power Gound
20 B0 Panel Data B0
21 B1 Panel Data B1
22 B2 Panel Data B2
23 B3 Panel Data B3
24 B4 Panel Data B4
25 B5 Panel Data B5
26 GND Power Gound
27 DE Data Enable
28 PANELVCC Panel Power
29 PANELVCC Panel Power
30 R/L Not connected
31 U/D Not connected
32 VGA/QVGA Not connected
, 0.5 mm pitch, 32 contacts.
Page 8
KAB-FLEX32-TSDD10
6
6.2 JILI30 Connector
Connector single row, 1.00mm pitch, 30 contacts (JAE, FI-X30S-HF or equivalent).
Pin Signal Name Function
1 FTX0- First Transmitter Signal 0-
2 FTX0+ First Transmitter Signal 0+
3 FTX1- First Transmitter Signal 1-
4 FTX1+ First Transmitter Signal 1+
5 FTX2- First Transmitter Signal 2-
6 FTX2+ First Transmitter Signal 2+
7 GND Power Gound
8 FTXC- First Transmitter Clock Signal
9 FTXC+ First Transmitter Clock Signal
10 NCNot connected
11 NCNot connected
12 NCNot connected
13 NCNot connected
14 GND Power Gound
15 NCNot connected
16 NCNot connected
17 GND Power Gound
18 NCNot connected
19 NCNot connected
20 NCNot connected
21 NCNot connected
22 NCNot connected
23 NCNot connected
24 GND Power Gound
25 NCNot connected
26 PPWR Data Enable
27 NC Not connected
28 VCC +5V Power Input
29 VCC +5V Power Input
30 VCC +5V Power Input
Page 9
KAB-FLEX32-TSDD10
7
7. Configuration
Caution! The supply voltage (+5V) of the KAB-ADAPT-LVDStoTTL must be configured on the flat panel
controller. See the technical manual of the specific controller.
7.1
R3 open, R4 short
Caution! Never short R3 and R4 at the same time! This will cause damage to the system!
3,3V Panel Power
R4 short
7.2 5,0V Panel Power
R3 short, R4 open
Caution! Never short R3 and R4 at the same time! This will cause damage to the system!
R3 short
Page 10
KAB-JILI30-TOLD06
8
APPENDIX A: REVISION HISTORY
Revision Date Edited by Changes
1.0 04/17/2007 S.Leuchtenberger First revision
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.