Kontron ETXexpress Eval Type 3 Quick Reference

Page 1
® Getting Started
Connector & Switch Locations:
® Introduction
ETXexpress Eval Type 3
Evaluation Carrier Board
38200-0000-00-0/1
This Quick Reference Guide provides Jumper and Connector locations for the ETXexpress Eval Type 3, an ETXexpress (ETXe) Carrier Board designed by Kontron to host ETXexpress Type 2 and Type 3 Modules. You can find Connector and Jumper names and descriptions on the next page. For complete infor mation on Carrier Board design, pin-outs, connectors, and Module Types 2 and 3, please refer to the Design Guide for ETXexpress Carrier Boards, which you can obtain from your local Kontron America sales off ice. Please refer to individual ETXexpress Module User Guides for more information. They also are available on the Kontron Web site.
For Technical Support, please contact: 1-800-480-0044, option 1 (U.S. and Canada) or (+49) 8165-77-112 (International)
The following information explains how to set up your ETXexpress Eval Type 3 Carrier Board and ETXexpress-WPM, a Type 3 Module.
1. In an ESD-protected area, remove the ETXexpress Carrier Board and ETXexpress Module from their packaging.
2. If necessary, install memory and a processor on the ETXe xpress Module.
3. Depending on your application, attach a fan, a heat sink, and a heat-spreader plate to the Module if needed.
4. Insert the ETXexpress Module into Connector J22 on the Carr ier Board.
5. Plug the ATX power supply into a surge protector that is plugged into an electrical outlet. Make sure that the external Power Supply is in t he “Off” position.
6. Insert the ATX power cable into Connector J41 on the Carrier Board. Insert the AUX power (+12V) cable into Connector J42 to power the ETXexpress Module.
7. Disable the Carrier Board’s BIOS by removing the jumper on Connector J16.
8. Insert a keyboard (bottom) and a mouse (top) into the PS/2 connectors (J5).
9. On the Carrier Board, plug in a storage device t o the appropriate Connector: Compact Flash (J40), IDE hard drive (J38), and SATA (J10, J12, J13, J14).
10. Turn on power.
COMPACT MODULE
BASIC MODULE
EXTENDED MODULE
J21
JP2
JP18
J27 J28 J31 J32 J34 J36 J39
J23
J24
J25
J26
J29
J30
J33
J37
J38
J40 J41 J42
J35
JP19
J22
J10
J12-J14
J11
J15
J16 J17 J18 J19
J20
J4 J6 J2J3 J1 J5
SW1
SW2
J8
J7
U1
U4
J9
JP1
JP20
mounting
hole
Quick Reference
Page 2
® Jumpers: ® Connectors:
For Technical Support, please contact: 1-800-480-0044, option 1 (U.S. and Canada) or (+49) 8165-77-112 (International)
ETXexpress Eval Type 3 Quick Reference
Connector Function Description
J1 VGA Female DB15 J2 USB2/3 Dual USB type A J3 Audio Connectors 3.5mm Phono Jacks J4 Ethernet, USB0/1 RJ45, Dual USB type A J5 Keyboard/Mouse PS/2 Combo J6 2x Gigabit Ethernet Dual RJ45 J7 Alt. AC97 Audio Interface 2x 5-pin friction header J8 CD Audio Input 4-pin friction header J9 Alternate BIOS Socket 32-pin PLCC socket J10 SATA data port1 7-pin Serial ATA J11 LPC Slot 60-contact card edge slot J12 SATA data port3 7-pin Serial ATA J13 SATA data port0 7-pin Serial ATA J14 SATA data port2 7-pin Serial ATA J15 PCI slot 124-pin 5V 32bit PCI J16 PCI-Express x4 slot4 164-contact card edge slot J17 PCI-Express x4 slot3 164-contact card edge slot J18 PCI-Express x4 slot2 164-contact card edge slot J19 PCI-Express x4 slot1 164-contact card edge slot J20 PCI-Express x4 slot0 164-contact card edge slot J21 JTAG Header 8-pin header J22 COM-Express Interface COM-Express A/B/C/D J23 USB6/7 2x 5-pin header J24 CMOS battery backup coin battery slot J25 LVDS Video Interface 40-pin Hirose ribbon conn. J26 USB4/5 2x 5-pin header
J27
Fan Header w/Tach and Speed Control
3-pin friction header
J28 Fan Header 3-pin friction header J29 COM1 2x 5 header J30 COM2 2x 5 header J31 Fan Header 3-pin friction header J32 Hard Drive Act. LED Interface 2-pin friction header J33 Parallel Port 2x 13 header J34 System PWR ON/OFF 2-pin friction header J35 GPIO 2x 5-pin header J36 System RESET header 2-pin friction header J37 COM3 2x 5 header J38 IDE 2x 20 header J39 SMBus connector 3-pin friction header J40 Compact Flash IDE 2x 25 CF Conn. J41 ATX Power 24-pin Molex J42 AUX Power 4-pin Molex SW1 System RESET switch Momentary switch SW2 System PWR ON/OFF switch Momentary switch U1 POST Code 7-Seg LED (LSB) POST Code LSB U4 POST Code 7-Seg LED (MSB) POST Code MSB
Jumper Description
JP1
Firmware Hub Write-Protection for both Module and Baseboard FWH's
JP2 JP3
PCI SLOT IDSEL & INT SIGNAL SELECT JP2 = S3, JP3 = S2
Emulate Slot#
Shunt S3
Shunt S2
Signal IDSEL
Signal INTA#
Signal INTB#
Signal INTC#
Signal
INTD#
0 0 0 AD[20] INTA# INTB# INTC# INTD# 1 0 1 AD[21] INTB# INTC# INTD# INTA# 2 1 0 AD[22] INTC# INTD# INTA# INTB# 3 1 1 AD[23] INTD# INTA# INTB# INTC#
JP4 JP5
PCI SLOT REQ & GNT SIGNAL SELECT JP4 = S0, JP5 = S1
Emulate Slot#
Shunt S1
Shunt S0
Signal REQ#
Signal
GNT##
0 0 0 REQ0# GNT0# 1 0 1 REQ1# GNT1# 2 1 0 REQ2# GNT2# 3 1 1 REQ3# GNT3#
JP6 S3_PSON_CNTL# JP7 S4_PSON_CNTL# JP8 S5_PSON_CNTL# JP9 P/S OFF (STBY Only) JP10 P/S ON (AT Mode) JP11 Express Card Detect Test for Card0 JP12 Express Card Detect Test for Card1 JP13 THRM# Test JP14 Alternate SIO Disable JP15 SIO Disable JP16 CPU Module BIOS Disable (Boot from Carrier Board BIOS) JP17 ETX COM Enable for COM3 JP18 Battery Low Test JP19 +5VSBY Jumper (Remove for 12V Only operation) JP20 Compact Flash M/S
Loading...