Kontron CRMS User Manual

Rack Mounting Options for Kontron
Communications Rack Mount Servers
Document Revision 1.0
1 Sep-09 www.kontron.com
Revision
Date
Comments
Revision History
1.0 9/9/09 Initial Release as stand-alone document
Copyright © 2009, Kontron
2 Sep-09 www.kontron.com
Rack Mounting Options for
Kontron Communications Rack Mount Servers
Rack mounting kits for 2-post or 4-post, 19-inch or 23-inch racks are offered for Kontron Communication Rack Mount Servers. Please refer to the tables below for the best options to suit your needs.
All rack mount kits listed are suitable for 1U and 2U Communications Rack Mount Servers. Installation instructions are included in each kit.
2-post Rack Mounting Kit Options
Rack width Post depth Rack fastener hole spacing
Applicable kits:
19 inch 23 inch 3 inch 5 inch EIA-Wide EIA-Universal ETSI
TMLCMOUNT21 TMLPMOUNT41 TMLPMOUNT51 TMLPMOUNT52
4-post Rack Mounting Kit Options
Rack width
Applicable kits:
19 inch 23 inch
TMLPMOUNT41 20 24 TMLPMOUNT51 20 24 TMLPMOUNT52 20 24
TMLPSLIDE01 22.5 28 or 34††
The TMLPSLIDE01 kit contains server securing brackets.
††
34-inch span requires the optional Accuride "Long Bracket" kit.
Front-post to
rear-post distance Min
(inches)
Max
(inches)
Wide
EIA-
Rack fastener
hole spacing
EIA-
Universal
ETSI
3 Sep-09 www.kontron.com
TMLCMOUNT21
The TMLCMOUNT21 kit mounts Communication Rack Mount Servers to a 2-post, central office type, 19-inch wide rack. This kit consists of L-shaped brackets that fasten to the sides of the server and to the rack.
TMLCMOUNT21
4 Sep-09 www.kontron.com
TMLPMOUNT41, TMLPMOUNT51 and TMLPMOUNT52
TMLPMOUNT41/51/52 series mounts Communication Rack Mount Servers to 2-post or 4-post racks.
TMLPMOUNT41 and TMLPMOUNT51 are used for mounting servers on 19-inch wide racks. These racks are considered standard EIA (universal hole spacing) racks.
TMLPMOUNT52 is used for mounting servers on 23-inch wide racks. These racks could be standard EIA (universal or wide hole spacing) or ETSI (European) racks.
TMLPMOUNT41/51/52 series are designed with a slide-in rail-type system. Although the mounts are designed as rails, they are not sliding rails. This means the servers can be slid into the racks for installation purpose, but the rails are not designed to support a mounted server during service.
TMLPMOUNT4x/5x Feature Comparison
spacing
4-post rack hole
Universal4
2U-tall nut bar
Included5
Included5
2-post chassis
securing screw
Side
access6
Front
access
Front
access
location
No Interference
"HP Mulan
Interference
N/A
Slide pull-out
TMLPMOUNT41 No1
TMLPMOUNT51 Yes
TMLPMOUNT52 Yes
locking feature
material
Slide interface
Plastic
strips2
Xylan
coating3
Xylan
coating3
EIA-Universal Not included
EIA-Wide or EIA-
EIA-Wide, EIA-
Universal or ETSI
Notes:
1. Extra care must be exercised with TMLPMOUNT41 to securely hold the server with one's hands when sliding it out of the rack; otherwise, the server could fall to the ground as it is being removed.
2. Plastic strips on TMLPMOUNT41 have peeled off in some customer installations. The result of this is that the parts are usable, but the server could have somewhat of a "scrape-in feel" rather than "slide in". Also, the rails will fit sloppier, so the side-located chassis securing screws could be difficult to align in 2-post installations. Replacement material is available from the plastic strip manufacturer.
3. Xylan is a tough, low-friction coating similar to Teflon.
4. EIA-Wide spacing doesn't have the interstitial hole that is present in EIA-Universal. TMLPMOUNT51 contains an adapter bracket to overcome this EIA-Wide issue.
5. This component (2U Nut Bar) enables installation of a rail kit into a 1U rack slot when there is already equipment installed both above and below that open slot.
6. The sides of the server must be accessible when using TMLPMOUNT41 in 2-post racks.
rack interference"
5 Sep-09 www.kontron.com
The diagrams above summarize the components and “slide-in rail-type” system of the TMLPMOUNT41. It can be adapted for a 2-post or 4-post installation.
6 Sep-09 www.kontron.com
The main difference between the TMLPMOUNT41 and TMLPMOUNT51/52 series is that the TMLPMOUNT41 series uses a screw to lock the server in place using the Universal Mounting Bracket, whilst the TMLPMOUNT51/52 series has an additional Slide Pull-Out Locking feature.
Universal Front Mounting Bracket on the TMLPMOUNT41
Slide Pull-Out Locking feature on the TMLPMOUNT51/52
7 Sep-09 www.kontron.com
TMLPSLIDE01
The TMLPSLIDE01 is an accessory kit designed for use in conjunction with slide rails to produce a rack mounted serviceable server. The TMLPSLIDE01 kit contains two Universal Front Mounting Brackets that secure the server to the front of the rack. The sliding rails and optional mounting brackets required to mount the server must be purchased through the channel. For example, the Accuride 22-inch Model 305A-LR slide rails are designed to mount a server for “in-rack service.” This example would also use an Accuride mounting bracket kit and the TMLPSLIDE01.
Universal Front Mounting Bracket with securing tab
Note: Using slide rails could result in non-compliance with Seismic Zone 4 requirements of NEBS-3 certification.
8 Sep-09 www.kontron.com
Loading...