22SATA Flash Module Layout (Top and Bottom Views) ................................................... 56
www.kontron.com
D R A F T — F O R I N T E R N A L U S E O N L Y
8
Page 9
User Guide
CPS3003-SA
Warranty
This Kontron product is warranted against defects in material and workmanship for the warranty period
from the date of shipment. During the warranty period, Kontron will at its discretion decide to repair
or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
specifications or improper installation or maintenance.
Kontron will not be responsible for any defects or damages to other products not supplied by Kontron
that are caused by a faulty Kontron product.
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any
means, disclosed to others, or stored in any retrieval system or media without the prior written consent
of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. However, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability
arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described herein, as seen fit by Kontron without further notice.
Trademarks
This document may include names, company logos and trademarks, which are registered trademarks
and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible.
Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are
capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.
www.kontron.com
D R A F T — F O R I N T E R N A L U S E O N L Y
9
Page 10
User Guide
CPS3003-SA
1 Introduction
1.1 Board Overview
CompactPCI® Serial, adopted by the PICMG® consortium in 2011, describes a new base standard. The
CompactPCI Serial standard introduces a completely new connector that enables a higher signal density and supports even higher transmission frequencies of up to 12 Gb/s as well as modern point-topoint connections such as PCI Express®, SATA, Ethernet and USB on the backplane.
The CPS3003-SA is a highly integrated 3U CompactPCI Serial CPU board based on Intel®'s 3
tion Core™ i7 technology in combination with the mobile Intel® QM77 Express Chipset. The CPU board
comes with a multi-core CPU package scalable from the dual-core ULV 1.7 GHz Intel® Core™ i7-3517UE
up to the quad-core 2.1 GHz i7-3612QE processor. The powerful PCH Intel® QM77 provides a variety of
interfaces either routed to front, onboard or the CompactPCI Serial connectors. Memory-demanding
applications can make use of up to 16 GB, 1600 MHz DDR3 SDRAM with Error Checking and Correction
(ECC). As another security feature, the CPS3003-SA provides a Trusted Platform Module (TPM) which
offers hardware-based encryption mechanisms to create, seal or store keys and other important system
data.
For graphics intensive applications, the CPS3003-SA offers an excellent graphics performance with integrated DirectX®11, OpenGL 3.1 and OpenCL 1.1 support as well as three independent graphics outputs.
The CPS3003-SA comes with a comprehensive I/O feature set supporting the latest high-speed interfaces such as USB 3.0, SATA 6Gb/s or PCI Express® 3.0. Communication interfaces available on the
front panel are two DisplayPort, two USB 2.0 and two Gigabit Ethernet ports. Serial interfaces available
on the CompactPCI Serial connectors P1 to P5 are eight USB ports, four SATA interfaces and 17x PCI
Express® links. Additional interfaces available on the P6 CompactPCI Serial rear I/O connector are two
Gigabit Ethernet interfaces, two USB ports, one DisplayPort and two serial ports.
rd
Genera-
By adding one of the four extension modules – Smart Extension Module, SATA Flash Module, CPS3003EXTIO or CPS3003-BRIDGE - the CPS3003-SA’s I/O and storage capabilities will be further extended.
The board is offered with various Board Support Packages including Windows, VxWorks and Linux operating systems. For further information concerning the operating systems available for the CP3003SA, please contact Kontron.
D R A F T — F O R I N T E R N A L U S E O N L Y
www.kontron.com
10
Page 11
User Guide
CPS3003-SA
1.2 System Expansion Capabilities
1.2.1 CPS3003-EXTIO Extension Module (8 HP)
The CPS3003-EXTIO module for the 8 HP CPS3003-SA version provides one USB 3.0 port, one COM port,
and one CFast socket on the front panel. For further information on the CPS3003-EXTIO extension module, refer to Chapter 6.
1.2.2 CPS3003-BRIDGE Extension Module (9 HP)
The CPS3003-BRIDGE module for the 9 HP CPS3003-SA version provides one USB 3.0 port, one COM
port, and one CFast socket on the front panel. In addition, the CPS3003-BRIDGE module is equipped
with a PCI Express-to-PCI bridge which converts PCI Express signals into PCI signals and makes them
available on theCompactPCI interface. For further information on the CPS3003-BRIDGE extension
module, refer to Chapter 7.
1.2.3 CPS-RIO3-01 Rear Transition Module
The CPS-RIO3-01 rear transition module provides comprehensive rear I/O functionality, such as one
DisplayPort, two COM ports, two Gigabit Ethernet ports, one USB 3.0 port, and one USB 2.0 port. For
further information on the CPS-RIO3-01 rear transition module, refer to Chapter 8.
1.2.4 Smart Extension Module
The Smart Extension Module can be used with the 4 HP CPS3003-SA and expands the onboard I/O capability providing one additional SATA cable connector as well as one USB 2.0 connector thereby facilitating the connection to system-internal USB and SATA devices. For further information on the Smart
Extension Module, refer to Chapter 9.
Note:If a Smart Extension Module is installed on the CPS3003-SA, the board width exceeds 4 HP.
1.2.5 SATA Flash Module
The SATA Flash module can be used with the 4 HP CPS3003-SA and provides up to 32 GB of SLC NAND
flash memory. For further information on the SATA Flash module, refer to Chapter 10.
1.3 Board Diagrams
The following diagrams provide additional information concerning board functionality and component
layout.
www.kontron.com
D R A F T — F O R I N T E R N A L U S E O N L Y
11
Page 12
1.3.1 Functional Block Diagram
DDR3 SDRAM
SODIMM with ECC
COM1-2, GPIO
Mobile Intel®
QM77
Express Chipset
4x
POST /
DEBUG /
GP /
Debug
12V
3rd Gen.
Intel® Core™ i7
Processor
DDR3DDR3
DMI
USB 2.0
LPC
SATA
USB 2.0
type-A
PCIe
FDI
USB 2.0
4x SATA
TPM
USB 2.0
type-A
DP B
6x USB 2.0
GbE B
PCIe
x1
High-
Speed
I/O
Extension
Connector
x1
2x USB 2.0
DP
GbE A
Watchdog
3.3/5V USB Power
Rear I/O Eth
SFF-XDP
SATA Flash
module
PCIe
PCIe 3.0 x4
5x PCIe 2.0 x1
PCIe
PCIe 3.0 x8
USB 3.0
2x USB 3.0 / 2.0
USB 2.0
USB 3.0
Rear I/O Eth
1x USB 3.0 / 2.0
1x USB 2.0
1x DisplayPort
P6 Rear I/O
DP
Power
Fat Pipe
I/O
DP A
Dual
UART
DDR3 SDRAM
SODIMM with ECC
CompactPCI
Serial
Front
RJ-45 + Mag.
Intel®
I210-IT
Intel®
I210-IT
GbE
Switch
GbE
Switch
Rear I/O Eth
Rear I/O Eth
2x DisplayPort
2x GbE
2x USB
LEDs
MAG
MAG
Hot Swap Handle
Power Button Func.
Hot Swap
Onboard Power Supplies
Thermal
RJ-45 + Mag.
CPLD
2x DP
SATA
USB 3.0
PCIe
Rear I/O
SATA
Rear I/O
PCIe
SPI
SPI Boot
Flashes
(standard/
recovery)
RTC
Battery
3V
optional
Figure 1: CPS3003-SA Functional Block Diagram
User Guide
CPS3003-SA
www.kontron.com
12
D R A F T — F O R I N T E R N A L U S E O N L Y
Page 13
1.3.2 Front Panel
CPS3003
DP-B
HSTHWD
DP-A
0
1
2
3
USB
SPEED
ACT
SPEED
ACT
System Status LEDs
HS (blue):Hot Swap Status
TH (red/green):Temperature Status
WD (green):Watchdog Status
General Purpose LEDs
LED3..0 (red/green/red+green): General Purpose/ POST Code
Note:If the General Purpose LEDs 3..0 are lit red during boot-up,
a failure is indicated before the uEFI BIOS has started.
Up to 32 GB SLC NAND flash via an onboard SATA Flash module (SSD)
» Compliant with PICMG® CPCI-S.0 R 1.0 CompactPCI® Serial Specification
» Support for the following interfaces:
» 7x PCI Express® (1 x8 PCI Express 3.0 on fat pipe, 1 x4 PCI Express 3.0 on
fat pipe and 5 x1 PCI Express 2.0)
» 4 x SATA (2 x SATA 6 Gb/s, 2 x SATA 3 Gb/s)
» 2 x USB 3.0 / 2.0
»6 x USB 2.0
» 2 x Gigabit Ethernet
» 12 V power supply
» Hot swap capability
» Capability of operation both in system slot and in peripheral slot
When installed in a peripheral slot, all interfaces except for the Ethernet
interfaces and rear I/O interfaces are isolated from the CompactPCI Serial
interface.
The following interfaces are routed to the CompactPCI Serial rear I/O connector P6:
» COMA and COMB, or COMA and GPIO (all ports have 3.3V LVTTL signaling)
»1 x USB 2.0
» 1 x USB 3.0 / 2.0
»DisplayPort
» 2x Gigabit Ethernet
» System control signals
» Input for RTC backup
Intel® I210-IT Ethernet controllers. Both interfaces are individually switchable to
front I/O or rear I/O and provide Wake-on-LAN support.
rd
generation processors:
User Guide
CPS3003-SA
D R A F T — F O R I N T E R N A L U S E O N L Y
www.kontron.com
15
Page 16
Table 1: CPS3003-SA Main Specifications (Continued)
FEATURESSPECIFICATIONS
USBUp to 13 USB ports:
» 6 x USB 2.0 on the CompactPCI Serial interface
» 2 x USB 3.0 / 2.0 on the CompactPCI Serial interface
» 2 x USB 2.0 ports on the front I/O
» 1 x USB 2.0 port on the rear I/O interface
» 1 x USB 3.0 / 2.0 port on the rear I/O interface
» 1 x USB 3.0 / 2.0 port on the CPS3003-EXTIO/CPS3003-BRIDGE extension
module
SerialTwo 16C550-compatible UARTs:
» COMA available on the CPS3003-EXTIO/CPS3003-BRIDGE extension module or
on rear I/O
» COMB or GPIO available on the rear I/O only
SATASix SATA ports:
» 2 x SATA 3 Gb/s onboard
» 2 x SATA 6 Gb/s on the CompactPCI Serial interface
» 2 x SATA 3 Gb/s on the CompactPCI Serial interface
High-performance RAID 0/1/5/10 functionality on all SATA ports
I/O Extension
Interfaces
Interfaces
I/O extension to 8 HP board version via the CPS3003-EXTIO module:
» CFast (SATA 3 Gb/s)
»USB 3.0
» COMA (RS-232)
»Reset button
» SATA activity LED
User Guide
CPS3003-SA
I/O extension to 9 HP board version via the CPS3003-BRIDGE module:
» CFast (SATA 3 Gb/s)
»USB 3.0
» COMA (RS-232)
»Reset button
» SATA activity LED
» CompactPCI interface
I/O extension of CPS3003-SA via the Smart Extension Module:
» SATA 3 Gb/s
»USB 2.0
» When installed 4HP width is exceeded
Front Panel ConnectorsDP:two DisplayPort connectors, J7 and J8
USB:two 4-pin, type A connectors, J9 and J10
Ethernet:dual RJ-45 connector, J11A/B
Onboard Connectors» CompactPCI Serial connectors P1 to P6
Sockets
» 18-pin extension connector for the SATA flash module (SSD), J16
» Two 204-pin DDR3 SODIMM sockets
» 60-pin, high-speed I/O extension connector
D R A F T — F O R I N T E R N A L U S E O N L Y
www.kontron.com
16
Page 17
Table 1: CPS3003-SA Main Specifications (Continued)
FEATURESSPECIFICATIONS
Front Panel LEDsSystem Status LEDs:
» HS (blue): Hot Swap Status
» TH (red/green):Temperature Status
» WD (green): Watchdog Status
General Purpose LEDs:
» LED3..0 (red/green/red+green): General Purpose / POST Code
LEDs / Switches
DIP SwitchOne DIP switch, SW1, for board configuration
Real Time ClockReal-time clock with 256 Byte CMOS RAM; battery-backup available
Watchdog TimerSoftware-configurable, two-stage Watchdog with programmable timeout ranging
Timer
Thermal ManagementCPU and board overtemperature protection is provided by:
Sys. Management
TPMTrusted Platform Module (TPM) 1.2 for enhanced hardware- and software-based
Security
uEFI BIOSAMI Aptio® BIOS firmware based on the uEFI Specification and the Intel Platform
Software
Operating SystemsThere are various operating systems available for the CPS3003-SA. For further
» Up to four Digital Thermal Sensors (DTS), one for each core
» One Digital Thermal Sensor (DTS) for the processor graphics controller
» One temperature sensor integrated in the Intel® QM77 Chipset for monitoring
the chipset
» Specially designed heat sinks
data and system security
Innovation Framework for EFI:
» LAN boot capability for diskless systems (standard PXE)
» Redundant image; recovery possible in case of a damaged image
» Non-volatile storage of setting in the SPI boot flash (battery only required for
the RTC)
» Compatibility Support Module (CSM) providing legacy BIOS compatibility
based on AMIBIOS8
» Command shell for diagnostics and configuration
» uEFI Shell commands executable from mass storage device in a Pre-OS envi-
ronment (open interface)
information, please contact Kontron.
User Guide
CPS3003-SA
www.kontron.com
D R A F T — F O R I N T E R N A L U S E O N L Y
17
Page 18
Table 1: CPS3003-SA Main Specifications (Continued)
FEATURESSPECIFICATIONS
Power ConsumptionSee Chapter 4 for details.
Temperature RangeOperational:0°C to +60°CStandard (depending on processor version and air-
-40°C to +85°CExtended (with Intel® Core™ i7-3517UE, 1.7 GHz ULV
Storage:-40°C to +85°CWithout hard disk and without battery
Battery3.0V lithium battery for RTC; Battery type: UL-approved CR1632
Temperature ranges:
Operational (load):-20°C to +70°Ctypical
General
Climatic Humidity93% RH at 40 °C, non-condensing (acc. to IEC 60068-2-78)
The above-mentioned board weight refers to the 4 HP CPS3003-SA without extension modules such as SATA Flash module or Smart Extension Module.
User Guide
CPS3003-SA
flow in the system)
processor only)
(refer to the battery manufacturer’s
specifications for exact range)
Note:For a description of the additional interfaces available on the 8 HP and 9 HP board ver-
sions, refer to Chapter 6, CPS3003-EXTIO Extension Module, and Chapter 7, CPS3003BRIDGE Extension Module, respectively.
1.5 Standards
This product complies with the requirements of the following standards.
Table 2: Standards
TYPEASPECTSTANDARD
CEEmissionEN55022, EN50121-3-2, EN61000-6-3
ImmissionEN55024, EN50121-3-2, EN61000-6-2
Electrical SafetyEN60950-1
MechanicalMechanical DimensionsIEEE 1101.10
EnvironmentalClimatic HumidityIEC60068-2-78
WEEEDirective 2002/96/EC
Waste electrical and electronic equipment
RoHS 2Directive 2011/65/EU
Restriction of the use of certain hazardous sub-
stances in electrical and electronic equipment
D R A F T — F O R I N T E R N A L U S E O N L Y
www.kontron.com
18
Page 19
User Guide
CPS3003-SA
In addition, boards ordered with the ruggedized service comply with the following standards as well.
Table 3: Additional Standards for Boards Ordered with Ruggedized Service
TYPEASPECTSTANDARDREMARKS
EnvironmentalVibration
(Sinusoidal)
Single ShockIEC60068-2-27
IEC60068-2-6
IEC61131-2
IEC61131-2
Ruggedized version test parameters:
9-150 (Hz) frequency range
1 (g) acceleration
1 (oct/min) sweep rate
10 cycles/axis
3 axis
Ruggedized version test parameters:
15 (g) acceleration
11 (ms) shock duration half sine
3 number of shocks per direction (total: 18)
6 directions
5 (s) recovery time
Note:Customers desiring to perform further environmental testing of the CPS3003-SA must con-
tact Kontron for assistance prior to performing any such testing.
Boards without conformal coating must not be exposed to a change of temperature which
can lead to condensation. Condensation may cause irreversible damage, especially when
the board is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destructive environmental testing.
1.6 Related Publications
The following publications contain information relating to this product.
Table 4: Related Publications
PRODUCTPUBLICATION
CompactPCI Serial SystemsPICMG® CPCI-S.0 R 1.0 CompactPCI® Serial Specification