Kontron 886LCD/ATX(GV) User Manual

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 1 of 71

User Manual

for the Mother Boards:

886LCD/ATX(GV)

886LCD/ATXU(GV)

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 2 of 71

Document revision history.

Revision Date By Comment

F May 18th 2009 MLA

E Jan. 14th 2009 MLA Minor corrections. PXE/RPL selection added to BIOS. D May 30th 2008 MLA Battery type updated and Battery load information added.

C Feb 8th, 2007 MLA

B June 6th, 2006 MLA Many minor corrections.

1.0 Mar 13th, 2006 PJA Release version.

0.1 Dec 9th, 2005 PJA First preliminary manual version.

Copyright Notice:

No part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.

Trademark Acknowledgement:

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer:

KONTRON Technology A/S reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Specifications listed in this manual are subject to change without notice. KONTRON Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or mask work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. KONTRON Technology A/S makes no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Battery alternative added. Corrected BIOS setting Graphics Mode Select.

Correction: Processor support table. JP3 connector included. Removal of “PCI Slot-3/4/5 IRQ Preference”

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 3 of 71

Life Support Policy

KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A/S.

As used herein:

1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.

2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

KONTRON Technology Technical Support and Services

If you have questions about installing or using your KONTRON Technology Product, check this User’s Manual first – you will find answers to most questions here. To obtain support, please contact your local Distributor or Field Application Engineer (FAE).

Before Contacting Support: Please be prepared to provide as much information as possible:

 CPU Board

1. Type.

2. Part-number (Number starting with “6”).

3. Serial Number.

 Configuration

1. CPU Type, Clock speed.

2. DRAM Type and Size.

3. BIOS Revision (Find the Version Info in the BIOS Setup in the Kontron Section).

4. BIOS Settings different than Default Settings (Refer to the Software Manual).

 System

1. O/S Make and Version.

2. Driver Version numbers (Graphics, Network, and Audio).

3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 4 of 71

Table of contents:

1.

INTRODUCTION.....................................................................................................................................7

2. INSTALLATION PROCEDURE..............................................................................................................8

2.1 Installing the board............................................................................................................................8

2.2 Requirement according to EN60950:...............................................................................................9

3. SYSTEM SPECIFICATION...................................................................................................................10

3.1 Component main data .....................................................................................................................10

3.2 Processor support table..................................................................................................................12

3.3 System Memory support.................................................................................................................14

3.4 System overview..............................................................................................................................15

3.5 Power Consumption........................................................................................................................16

4. CONNECTOR DEFINITIONS................................................................................................................17

4.1 Connector layout..............................................................................................................................18

4.1.1 886LCD/ATXU(GV) ....................................................................................................................18

4.1.2 886LCD/ATX(GV) .......................................................................................................................19

4.2 Power Connector (ATXPWR, ATXPWR+12V)................................................................................20

4.3 Keyboard and PS/2 mouse connectors.........................................................................................21

4.3.1 Stacked MINI-DIN keyboard and mouse Connector (MSE & KBD) ........................................... 21

4.4 Display Connectors.........................................................................................................................22

4.4.1 CRT Connector (CRT)................................................................................................................22

4.4.2 (AGP)/DVO connector ................................................................................................................23

4.5 Parallel ATA harddisk interface......................................................................................................25

4.5.1 IDE Hard Disk Connector (IDE_P) .............................................................................................26

4.5.2 IDE Hard Disk Connector (IDE_S) .............................................................................................26

4.6 Serial ATA harddisk interface.........................................................................................................27

4.6.1 SATA Hard Disk Connector (SATA0, SATA1) ...........................................................................27

4.7 Floppy Disk Connector (FDC1).......................................................................................................28

4.8 Printer Port Connector (PRINTER).................................................................................................29

4.9 Serial Ports.......................................................................................................................................30

4.9.1 Serial Port Com1 DB9 Connector...............................................................................................30

4.9.2 Serial Port Com2 Pin Header Connectors.................................................................................. 30

4.10 Ethernet connector. .....................................................................................................................31

4.10.1 Ethernet connector (ETHER)......................................................................................................31

4.11 USB Connector (USB)..................................................................................................................32

4.11.1 USB Connector 0/1 (USB0/1).....................................................................................................32

4.11.2 USB Connector 2/3 (USB2/3).....................................................................................................33

4.11.3 USB Connector 4/5 (USB4/5).....................................................................................................33

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 5 of 71

4.12

Audio Connector ..........................................................................................................................34

4.12.1 Audio Line-in, Line-out and Microphone..................................................................................... 34

4.12.2 CD-ROM Audio input (CDROM).................................................................................................34

4.13 Fan connectors, CPU FAN, CHASSIS FAN, PWR FAN.............................................................35

4.14 The Clear CMOS Jumper, Clr-CMOS..........................................................................................36

4.15 Front Side Bus Speed, FSB.........................................................................................................36

4.16 Case Open, S1 ..............................................................................................................................37

4.17 Trusted Platform Module (TPM) connector, CN7 (unsupported). ...........................................37

4.18 Front Panel connector, CN5........................................................................................................38

4.19 GAME / MIDI Connector, CN6......................................................................................................39

4.20 IR Connector (IR1)........................................................................................................................39

4.21 WOL Connector (W.O.L)..............................................................................................................40

4.22 JP3 (optional)................................................................................................................................40

4.23 PCI Slot 1, Slot 2 and Slot 3 connectors...................................................................................41

4.23.1 PCI Slot Connector ....................................................................................................................41

4.23.2 Signal Description –PCI Slot Connector..................................................................................... 42

4.23.3 886LCD/ATX(GV) and 886LCD/ATXU(GV) PCI IRQ & INT routing ..........................................43

5. SYSTEM RESOURCES........................................................................................................................44

5.1 Memory map.....................................................................................................................................44

5.2 PCI devices.......................................................................................................................................44

5.3 Interrupt Usage ................................................................................................................................45

5.4 I/O Map ..............................................................................................................................................46

5.5 DMA Channel Usage........................................................................................................................46

6. OVERVIEW OF BIOS FEATURES.......................................................................................................47

6.1.1 System Management BIOS (SMBIOS / DMI) ............................................................................. 47

6.1.2 Legacy USB Support ..................................................................................................................47

7. BIOS CONFIGURATION / SETUP .......................................................................................................48

7.1 Introduction......................................................................................................................................48

7.2 Main Menu.........................................................................................................................................48

7.3 Advanced Menu................................................................................................................................49

7.3.1 Advanced settings – CPU Configuration ....................................................................................49

7.3.2 Advanced settings – IDE Configuration......................................................................................50

7.3.3 Advanced settings – Floppy Configuration.................................................................................52

7.3.4 Advanced settings – SuperIO Configuration ..............................................................................53

7.3.5 Advanced settings – Hardware Health Configuration ................................................................54

7.3.6 Advanced settings – ACPI Configuration ...................................................................................55

7.3.7 Advanced settings – General ACPI Configuration .....................................................................56

7.3.8 Advanced settings – Advanced ACPI Configuration .................................................................. 57

7.3.9 Advanced settings – USB Configuration ....................................................................................58

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 6 of 71

7.3.10 Advanced settings – USB Mass Storage Device Configuration.................................................59

7.4 PCIPnP Menu....................................................................................................................................60

7.5 Boot Menu.........................................................................................................................................61

7.5.1 Boot – Boot Settings Configuration ............................................................................................62

7.6 Security Menu...................................................................................................................................63

7.7 Chipset Menu....................................................................................................................................64

7.7.1 Advanced Chipset Settings – Intel Brookdale-G NorthBridge Configuration ............................. 65

7.7.2 Advanced Chipset Settings – SouthBridge Configuration.......................................................... 66

7.8 Power Menu......................................................................................................................................67

7.9 Exit Menu..........................................................................................................................................68

7.10 AMI BIOS Beep Codes.................................................................................................................69

8. OS SETUP.............................................................................................................................................70

9. WARRANTY..........................................................................................................................................71

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 7 of 71

1. Introduction

This manual describes the 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards made by KONTRON Technology A/S. The boards will also be denoted 886LCD-GV family if no differentiation is required.

All boards are to be used with the Intel® Pentium® 4, Intel Celeron® and Intel® Celeron® D Processors.

Use of this manual implies a basic knowledge of PC-AT hard- and software. This manual is focused on describing the 886 Board’s special features and is not intended to be a standard PC-AT textbook.

New users are recommended to study the short installation procedure stated in chapter 2 before switchingon the power.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 8 of 71

2. Installation procedure

2.1 Installing the board

To get the board running, follow these steps. In some cases the board shipped from KONTRON Technology has CPU, DDR DRAM and Cooler mounted. In this case Step 2-4 can be skipped.

1. Turn off the power supply.

Warning: Do not use Power Supply without voltage monitoring watchdog, which is

standard feature in ATX Power Supplies.

!

2. Insert the DIMM DDR 184pin DRAM module(s). Be careful to push it in the slot(s) before locking the

tabs. For a list of approved DDR DRAM modules contact your Distributor or FAE. DIMM 184pin DRAM modules are supported.

3. Install the processor. The CPU is keyed and will only mount in the CPU socket in one way. Use the

handle to open/ close the CPU socket. Intel® Pentium® 4, Celeron® and Celeron® D processors are supported.

4. Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the FAN3

connector. (See chapter 4.1 for identifying the FAN3 connector).

5. Insert all external cables for hard disk, keyboard etc. except for flat panel. A CRT monitor must be

connected in order to change CMOS settings to flat panel support (with ADD-DVO module). To achieve

UDMA-66/100/133 performance on the IDE interface, 80poled UDMA cables must be used.

6. Connect power supply to the board by the ATXPWR connector.

7. Turn on the ATX power supply.

8. The PWRSW must be toggled to start the Power supply; this is done by shorting pins pins 19 and 21 on the

CN5 connector (see Connector description). A “normally open” switch can be connected via the CN5 connector.

9. Enter the BIOS setup by pressing the “F2” key during boot up. Refer to the Software Manual for details on

BIOS setup.

Note: To clear all CMOS settings, including Password protection, move the JP6 jumper (with or without power)

for approximately 1 minute. Alternatively turn off power and remove the battery for 1 minute, but be careful to orientate the battery corretly when reinserted.

Running the board without 3.3V connected will damage the board after a few minuttes.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 9 of 71

2.2 Requirement according to EN60950:

Users of 886LCD-GV boards should take care when designing chassis interface connectors in order to fulfill the EN60950 standard:

When an interface/connector has a VCC (or other power) pin, which is directly connected to a power plane like the VCC plane:

To protect the external power lines of peripheral devices the customer has to take care about:

• That the wires have the right diameter to withstand the maximum available power.

• That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC/EN 60950.

Lithium Battery precautions:

CAUTION!

Danger of explosion if battery is incorrectly

replaced.

Replace only with same or equivalent type

recommended by manufacturer.

Dispose of used batteries according

to the manufacturer’s instructions.

ADVARSEL!

Lithiumbatteri – Eksplosionsfare ved fejlagtig

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

Explosionsgefahr bei unsachgemäßem Austausch

Ersatz nur durch den selben oder einen vom

Hersteller empfohlenen gleichwertigen Typ.

Entsorgung gebrauchter Batterien nach

Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende

type anbefalt av apparatfabrikanten.

Brukte batterier kasseres i henhold til fabrikantens

VORSICHT!

der Batterie.

Angaben des Herstellers.

ADVARSEL

instruksjoner.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti

asennettu.

Vaihda paristo ainoastaan laltevalmistajan

suosittelemaan

tyyppiln. Hävitä käytetty paristo valmistajan

ohjeiden

mukaisesti.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 10 of 71

3. System specification

3.1 Component main data

The table below summarises the features of the 886LCD-GV embedded motherboards.

Form factor Processor

Memory

Chipset

Video

Audio

I/O Control Peripheral interfaces

LAN Support BIOS

886LCD/ATXU(GV): uATX (244,1 x 305,0 mm) 886LCD/ATX(GV): ATX (190,5 x 304,0 mm)

• Support for Intel® Pentium® 4, Intel Celeron® and Intel® Celeron® D Processors in mPGA478 socket with 400MHz/ 533MHz system bus.

• 0.13 micron and 90nm Architecture support

• L2 cache: 128KB, 256KB and 512KB

• 2x184pin DDR SDRAM Dual Inline Memory Module (DIMM) sockets.

• Support for DDR 266 (PC2100). DRAM supporting higher speeds: DDR 333

(PC2700) and DDR 400 (PC3200) may be used after qualification testing.

• Support for up to 2GB of system memory

• ECC not supported

Intel 845GV Chipset consisting of:

• Intel® 82845GV Graphics and Memory Controller Hub (GMCH)

• Intel® 82801DB I/O Controller Hub 4 (ICH4)

• 4 Mbit Firmware Hub (FWH) for BIOS

• Intel Extreme Graphics controller

• Video memory support: maximum 64MB with more than 128MB DDR SDRAM

installed.

• The GMCH has an integrated 350 MHz RAMDAC that can directly drive a progressive scan analog monitor up to a resolution of 2048x1536 at 60 Hz.

• The GMCH provides two multiplexed Digital Video Out Ports (DVOs) through the onboard AGP 2.0, 1.5V connector that are can drive a 165 MHz pixel clock.

o DVI DVO ADD, CRT DVO ADD and LVDS DVO ADD cards supported

Note: Only ADD cards are supported , AGP cards are not supported. Audio, AC97 version 2.3 subsystem using the Realtek ALC655 codec

• Line-out

• Line-in

• CDROM in

• Microphone

Winbond W83627HG LPC Bus I/O Controller

• USB host interface; 3 host controllers and supports 6 USB ports; includes a EHCI high-speed 2.0 USB controller. USB legacy keyboard function supported.

• Two Serial ports (RS232). Port 2 can be set to operate in normal, IrDA or ASKIR mode

• One Parallel port, SPP/EPP/ECP

• One Floppy port

• Two Serial ATA 150 IDE interfaces.

• Two Parallel ATA IDE interfaces with UDMA 33, ATA-66, ATA-100 support

• PS/2 keyboard and mouse ports

• Game/Midi port

1x 10/100Mbits/s LAN subsystem using the Realtek RTL8100C LAN controllers. PXE netboot supported. Wake On LAN (WOL) supported.

• Kontron Technology / AMI BIOS (core version 8.00)

• Support for Advanced Configuration and Power Interface (ACPI 1.0, 2.0), Plug and

Play

o Suspend To Ram o Suspend To Disk

• SW Watchdog not supported by BIOS

• Secure CMOS/ OEM Setup Defaults

• “Always On” BIOS power setting

• SATA RAID Support (RAID modes 0 and 1)

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 11 of 71

Instantly Available PC Technology Expansion Capabilities

Hardware Monitor Subsystem

Operating Systems Support

Environmental Conditions

Battery

• PCI Rev 2.2 compliant with support for 33 MHz PCI operations

• Suspend to RAM support

• PCI Bus routed to PCI slot(s) (PCI Local Bus Specification Revision 2.2)

• 3 x PCI bus with Bus master mode on 886LCD/ATXU(GV) board

• 6 x PCI bus with Bus master mode on 886LCD/ATX(GV) board

• 2 x DVO ports for ADD card expansion

• LPC Bus routed to CN7 connector / Trusted Platform Module Header

• Fan monitoring: CPU FAN, CHASSIS FAN, PWR FAN

• Thermal monitoring: CPU die temperature, System temperature and External

temperature input (routed to JP3 connector).

• Voltage monitoring

• Intrusion detect input (JP6)

• SMI violations (BIOS) on HW monitor not supported. Supported by API (Windows)

• WinXP

• Win2000

• Win2003

• WinXP Embedded (limitations may apply)

• WinCE.net (limitations may apply)

• Linux: Feodora Core 3, Suse 9.2 (limitations may apply)

Operating:

0°C – 60°C operating temperature (forced cooling). It is the customer’s responsibility to provide sufficient airflow around each of the components to keep them within allowed temperature range.

Storage: -20°C – 70°C and 5% - 95% relative humidity (non-condensing)

Electro Static Discharge (ESD) / Radiated Emissions (EMI):

All Peripheral interfaces intended for connection to external equipment are ESD/ EMI protected. EN 61000-4-2:2000 ESD Immunity EN55022:1998 class B Generic Emission Standard.

Safety:

UL 60950-1:2003, First Edition CSA C22.2 No. 60950-1-03 1st Ed. April 1, 2003 Product Category: Information Technology Equipment Including Electrical Business Equipment Product Category CCN: NWGQ2, NWGQ8 File number: E194252

Theoretical MTBF:

129679 hours (14,5 years). Calculation based on Telcordia SR-332 method.

Restriction of Hazardeous Substances (RoHS):

886LCD/ATX(GV) and 886LCD/ATXU(GV) boards are RoHS compliant.

Capacitor utilization:

No Tantal capacitors on board. Only Japanese brand Aluminium capacitors rated for 100 ºC used on board.

Exchangeable 3.0V Lithium battery for onboard Real Time Clock and CMOS RAM.

Manufacturer Panasonic / PN CR2032NL/LE, CR-2032L/BE or CR-2032L/BN.

Expected minimum 5 years retention varies depending on temperature, actual application on/off rate and variation within chipset and other components.

Approximately current draw is 3.7µA (no PSU connected).

CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 12 of 71

3.2 Processor support table.

886LCD/ATX(GV) and 886LCD/ATX(GV) boards are designed to support the following processors: Intel® Pentium® 4 Processors Intel® Celeron® D Processors Intel Celeron® Processors

Speed

Intel® Pentium 4® Embedded Processors

2.0A GHZ 400MHz FSB 512K RK80532PC041512

2.40 GHZ 533MHz FSB 512K RK80532PE056512

2.60 GHZ 400MHz FSB 512K RK80532PC064512

2.80 GHZ 400MHz FSB 512K RK80532PE072512

Intel® Celeron® Embedded Processors

2.00 GHZ, 400MHz FSB 128K RK80532RC041128

2.50 GHZ, 400MHz FSB 128K RK80532RC060128

Cache

size

Product Order Code

Intel

Single Pack

Intel

OEM Product

Order Code

Intel® Celeron® D Embedded Processors

2.80 GHz, 533MHz FSB 256K BX80546RE2800C RK80546RE072256

Intel® Pentium 4® Processors

1.60 GHZ, 400MHz FSB 512K RK80534PC025512

1.60 GHZ, 400MHz FSB 512K BX80532PC1600D

1.80 GHZ, 400MHz FSB 512K RK80534PC033512

1.80 GHZ, 400MHz FSB 512K BX80532PC1800D RK80532PC033512

2.00 GHZ, 400MHz FSB 512K BX80532PC2000D RK80532PC041512

2.20 GHZ, 400MHz FSB 512K BX80532PC2200D RK80532PC049512

2.26 GHZ, 533MHz FSB 512K BX80532PE2266D RK80532PE051512

2.40 GHZ, 400MHz FSB 512K BX80532PC2400D RK80532PC056512

2.40 GHZ, 533MHz FSB 512K BX80532PE2400D RK80532PE056512

2.50 GHZ, 400MHz FSB 512K BX80532PC2500D RK80532PC060512

2.53 GHZ, 533MHz FSB 512K BX80532PE2533D RK80532PE061512

2.60 GHZ, 400MHz FSB 512K BX80532PC2600D RK80532PC064512

2.66 GHZ, 533MHz FSB

2.80 GHZ, 533MHz FSB

3.06 GHZ, 533MHz FSB, HT* 512K BX80532PE3066D RK80532PE083512

Intel® Celeron® Processors

512K 512K

BX80532PE2667D RK80532PE067512 BX80532PE2800D RK80532PE072512

1.70 GHZ, 400MHz FSB 128K BX80531P170G128 RK80531RC029128

1.80 GHZ, 400MHz FSB 128K BX80531P180G128 RK80531RC033128

2.00 GHZ, 400MHz FSB 128K BX80532RC2000B RK80532RC041128

2.10 GHZ, 400MHz FSB 128K BX80532RC2100B RK80532RC045128

2.20 GHZ, 400MHz FSB 128K BX80532RC2200B RK80532RC049128

2.30 GHZ, 400MHz FSB 128K BX80532RC2300B RK80532RC052128

2.30 GHZ, 400MHz FSB 128K B80532RC052128

2.40 GHZ, 400MHz FSB 128K BX80532RC2400B RK80532RC056128

2.50 GHZ, 400MHz FSB 128K BX80532RC2500B RK80532RC060128

2.60 GHZ, 400MHz FSB 128K BX80532RC2600B RK80532RC064128

2.70 GHZ, 400MHz FSB 128K BX80532RC2700B RK80532RC068128

2.80 GHZ, 400MHz FSB 128K BX80532RC2800B RK80532RC072128

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 13 of 71

Speed

Intel® Celeron® D Processors

3.20 GHz, 533MHz FSB 256K BX80546RE3200C RK80546RE088256

3.06 GHz, 533MHz FSB 256K BX80546RE3066C RK80546RE083256

2.93 GHz, 533MHz FSB 256K BX80546RE2933C RK80546RE077256

2.80 GHz, 533MHz FSB 256K BX80546RE2800C RK80546RE072256

2.66 GHz, 533MHz FSB 256K BX80546RE2667C RK80546RE067256

2.53 GHz, 533MHz FSB 256K BX80546RE2533C RK80546RE061256

2.40 GHz, 533MHz FSB 256K BX80546RE2400C RK80546RE056256

2.26 GHz, 533MHz FSB 256K BX80546RE2267C RK80546RE051256

2.13 GHz, 533MHz FSB 256K BX80546RE2130C RK80546RE046256 * HT = Hyper Threading support

Cache

size

Product Order Code

Intel

Single Pack

Intel

OEM Product

Order Code

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 14 of 71

3.3 System Memory support

The 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards have two onboard DIMM sockets and support the following memory features:

• 2.5V (only) 184-pin DDR SDRAM DIMMs with gold-plated contacts

• Supports up to two single-sided and/or double-sided DIMMs (four rows populated) with unbuffered

PC1600/PC2100 DDR-SDRAM

• Supports 64 Mbit, 128 Mbit, 256 Mbit and 512 Mbit technologies for x8 and x16 width devices.

• Maximum of 2 Gbytes system memory by using 512 Mbit technology devices (double sided)

• Supports 200 MHz and 266 MHz DDR devices

• 64-bit data interface

• ECC not supported with the Intel 845GV chipset

The installed DDR SDRAM should support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the BIOS will attempt to configure the memory settings, but performance and reliability may be impacted.

In general DDR SDRAM with higher speeds than 266MHz may be used (e.g. 333MHz or 400MHz), but it is recommended to run a qualification test before use or to use Kontron Technology validated DDR SDRAM.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 15 of 71

3.4 System overview

The block diagram below shows the architecture and main components of the 886LCD boards. The two key components on the board are the Intel

®

845GV and Intel® ICH4 Embedded Chipsets.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 16 of 71

3.5 Power Consumption

This section describes static and dynamic power consumption on the 886LCD/ATXU(GV) board in a specific configuration:

• 886LCD/ATXU(GV)

• P4, 2.0GHz, 400MHz FSB, 256MByte L2 cache

• P4 cooler

• 256Mbyte of PC2100 / 266MHz DDR SDRAM

• VGA monitor, Keyboard and mouse inserted

Wire colour Yellow

(CPU)

Voltage

State

XP Idle DC 0,74 0,24 2,65 0,34 0,02 0,06 0,03 23,60 XP Idle AC 0,06 0,00 0,05 0,07 0,03 0,04 0,05 2,54 XP Idle power 26,13

XP Full Load DC 3,60 0,29 3,66 0,34 0,03 0,04 0,04 61,57 XP Full Load AC 0,38 0,02 0,29 0,08 0,03 0,04 0,04 7,34 XP Full Load power 68,91

12,00 V 5,00 V 3,30 V 12,00 V -12,00 V 5,00 V -5,00 V

/[A] /[A] /[A] /[A] /[A] /[A] /[A]

Red Orange Yellow Blue

Purple White Total Power

/[W]

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 17 of 71

4. Connector Definitions

The following sections provide pin definitions and detailed description of all on-board connectors. . The connector definitions follow the following notation:

Column

name

Pin Shows the pin-numbers in the connector. The graphical layout of the connector definition

tables is made similar to the physical connectors.

Signal The mnemonic name of the signal at the current pin. The notation “XX#” states that the signal

“XX” is active low.

Type AI : Analog Input.

AO : Analog Output.

I : Input, TTL compatible if nothing else stated.

IO : Input / Output. TTL compatible if nothing else stated.

IOT : Bi-directional tristate IO pin.

IS : Schmitt-trigger input, TTL compatible.

IOC : Input / open-collector Output, TTL compatible.

NC : Pin not connected.

O : Output, TTL compatible.

OC : Output, open-collector or open-drain, TTL compatible.

OT : Output with tri-state capability, TTL compatible.

LVDS: Low Voltage Differential Signal.

PWR : Power supply or ground reference pins.

Ioh: Typical current in mA flowing out of an output pin through a grounded load, while the

output voltage is > 2.4 V DC (if nothing else stated).

Iol: Typical current in mA flowing into an output pin from a VCC connected load, while the output voltage is < 0.4 V DC (if nothing else stated).

Pull U/D On-board pull-up or pull-down resistors on input pins or open-collector output pins.

Note Special remarks concerning the signal.

The abbreviation TBD (To Be Determined) is used for specifications which are not available yet or which are

not sufficiently specified by the component vendors.

Description

(

ATXPWR

FAN3

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 18 of 71

4.1 Connector layout

4.1.1 886LCD/ATXU(GV)

FLOPPY

DIMM2

DIMM1

IDE_P

TPM

IDE_S

FSB

CASE OPEN

Clr-CMOS

FRONT PANEL, CN5

GAME/ MIDI, CN6

WOL

IR

USB2/3

AGP)/DVO

SATA1

SATA0

COM2

FAN1

JP3

FAN2

PCI SLOT 1

ATXPWR +12V

CDROM

COM1

MSE KBD

USB0 USB1

PRINTER

CRT

LINE-IN

LINE-OUT

MIC

ETHER

USB4

PCI SLOT 3

PCI SLOT 2

(

ATXPWR

FAN3

FAN2

ATXPWR +12V

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 19 of 71

4.1.2 886LCD/ATX(GV)

FLOPPY

MSE

KBD

IDE_P

USB0 USB1

IDE_S

COM1

DIMM2

DIMM1

TPM

PRINTER

CRT

FSB

CASE

Clr-CMOS

LINE-OUT

ETHER

USB4

USB2/3

FAN1

CDROM

LINE-IN

MIC

FRONT PANEL,

GAME/

AGP)/DVO

PCI SLOT 6

PCI SLOT 5

PCI SLOT 4

PCI SLOT 3

PCI SLOT 2

PCI SLOT 1

WOL

IR

COM2

SATA1

SATA0

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 20 of 71

4.2 Power Connector (ATXPWR, ATXPWR+12V)

The 886LCD/ATX(GV) and 886LCD/ATXU(GV) is designed to be supplied from a standard ATX power supply.

ATX Power Connector 886LCD/ATX(GV) and 886LCD/ATXU(GV)

Note

- - PWR +12V 10 20 5V PWR - -

- - PWR SB5V 9 19 5V PWR - - 4K7 - I P_OK 8 18 -5V PWR - - 1

- - PWR GND 7 17 GND PWR - -

- - PWR 5V 6 16 GND PWR - -

- - PWR GND 5 15 GND PWR - -

- - PWR 5V 4 14 PSON# OC - -

- - PWR GND 3 13 GND PWR - -

- - PWR 3V3 2 12 -12V PWR - -

- - PWR 3V3 1 11 3V3 PWR - -

Note: -5V supply is not used onboard.

+12V Power Connector 886LCD/ATX(GV) and 886LCD/ATXU(GV)

Note

- - PWR GND 4 3 +12V PWR - -

- - PWR GND 2 1 +12V PWR - -

The requirements to the supply voltages are as follows (also refer to ATX specification version 2.03):

Supply Min Max Tolerance

3V3 3.14V 3.46V +/-5%

5V 4.75V 5.25V +/-5%

SB5V 4.75V 5.25V +/-5%

+12V 11.4V 12.6V +/-5%

–12V –13.2V –10.8V +/-10%

Control signal description:

P_OK Active high signal from the power supply indicating that the 5V and 3V3 supplies are within

PS_ON# Active low open drain signal from the board to the power supply to turn on the power supply

Pull

U/D Ioh/Iol Type Signal

Pull

U/D Ioh/Iol Type Signal

operating limits. It is strongly recommended to use an ATX supply with the 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards, in order to implement the supervision of the 5V and 3V3 supplies. These supplies are not supervised onboard the 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards.

outputs. Signal must be pulled high by the power supply.

Signal Type Ioh/Iol

Pull U/D

Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 21 of 71

4.3 Keyboard and PS/2 mouse connectors

Attachment of a keyboard or PS/2 mouse adapter can be done through the stacked PS/2 mouse and keyboard connector (MSE & KBD).

Both interfaces utilize open-drain signaling with on-board pull-up.

The PS/2 mouse and keyboard is supplied from 5V_STB when in standby mode in order to enable keyboard or mouse activity to bring the system out from power saving states. The supply is provided through a 1.1A resetable fuse.

4.3.1 Stacked MINI-DIN keyboard and mouse Connector (MSE & KBD)

Pull

Note

Signal Description – Keyboard & and mouse Connector (MSE & KBD), see below.

U/D Ioh/Iol Type Signal

- - - NC 6 5MSCLK IOC TBD 2K2

- - PWR 5V/SB5V 4 3 GND PWR - -

- - - NC 2 1 MSDAT IOC TBD 2K2

- NC 6 5KBDCLK IOC TBD 2K2

- - PWR 5V/SB5V 4 3 GND PWR - -

- - - NC 2 1 KBDDAT IOC TBD 2K2

Signal Type Ioh/Iol

Pull

U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 22 of 71

4.4 Display Connectors

The 886LCD board family provides onboard two basic types of interfaces to a display: Analog CRT interface and a digital interface typically used with flat panels. The digital interface to flat panels can be achieved through the DVO port available on the AGP connector by using a dedicated ADD card.

4.4.1 CRT Connector (CRT)

Pull

Note

Note 1: The 5V supply in the CRT connector is fused by a 1.1A reset-able fuse.

Signal Description - CRT Connector:

HSYNC CRT horizontal synchronization output.

VSYNC CRT vertical synchronization output.

DDCCLK Display Data Channel Clock. Used as clock signal to/from monitors with DDC interface.

DDCDAT Display Data Channel Data. Used as data signal to/from monitors with DDC interface.

RED Analog output carrying the red color signal to the CRT. For 75 Ohm cable impedance.

GREEN Analog output carrying the green color signal to the CRT. For 75 Ohm cable impedance.

BLUE Analog output carrying the blue color signal to the CRT. For 75 Ohm cable impedance.

DIG-GND Ground reference for HSYNC and VSYNC.

ANA-GND Ground reference for RED, GREEN, and BLUE.

U/D Ioh/Iol Type

6 ANA-GND PWR - -

/75R * A0 RED 1 11 NC - - - 7 ANA-GND PWR - - /75R * A0 GREEN 2 12 DDCDAT IO TBD 2K7 8 ANA-GND PWR - - /75R * A0 BLUE 3 13 HSYNC O TBD 9 5V PWR - - 1

- - - NC 4 14 VSYNC O TBD 10 DIG-GND PWR - -

- - PWR DIG-GND 5 15 DDCCLK IO TBD 2K7

Signal

Signal Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 23 of 71

4.4.2 (AGP)/DVO connector

The 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards are equipped with the Intel 845GV chipset. The GV chipset does not support AGP output, but only DVO output.

Note Type Signal PIN Signal Type Note

OVRCNT B1 A1 +12V PWR PWR +5V B2 A2 TYPEDET PWR +5V B3 A3 RSVD NC B4 A4 NC PWR GND B5 A5 GND PWR INTB B6 A6 INTA AGPCLK B7 A7 RST- GREQ B8 A8 GGNT PWR +3.3V B9 A9 +3.3V PWR ST0 B10 A10 ST1 ST2 B11 A11 RSVD I RBF B12 A12 PIPE I PWR GND B13 A13 GND PWR RSVD B14 A14 WBF I I ADD_ID0 B15 A15 ADD_ID1 I PWR +3.3V B16 A16 +3.3V PWR I ADD_ID2 B17 A17 ADD_ID3 I I ADD_RS B18 A18 ADD_RS PWR GND B19 A19 GND PWR I ADD_ID4 B20 A20 ADD_ID5 I I ADD_ID6 B21 A21 ADD_ID7 I RSVD B22 A22 RSVD PWR GND B23 A23 GND PWR PWR 3V3AUX B24 A24 RSVD PWR +3.3V B25 A25 +3.3V PWR DVOC_Fld/Stl B26 A26 DVOBC_Intr- DVOC_D10 B27 A27 DVOC_D11 PWR +3.3V B28 A28 +3.3V PWR DVOC_D8 B29 A29 DVOC_D9 DVOC_D6 B30 A30 DVOC_D7 PWR GND B31 A31 GND PWR DVOC_Clk+ B32 A32 DVOC_Clk- DVOC_D4 B33 A33 DVOC_D5 PWR +1.5V B34 A34 +1.5V PWR DVOC_D2 B35 A35 DVOC_D3 DVOC_D0 B36 A36 DVOC_D1 PWR GND B37 A37 GND PWR DVOC_Hsync B38 A38 DVOC_Blank- ADD_RS B39 A39 DVOC_Vsync PWR +1.5V B40 A40 +1.5V PWR M_I2CClk B41 A41 M_DVI_Data

M_I2CData B46 A46 M_DVI_Clk PWR +1.5V B47 A47 M_DDCData GPERR B48 A48 PME PWR GND B49 A49 GND PWR GSERR B50 A50 ADD_Detect DVOB_Blank- B51 A51 M_DDCClk PWR +1.5V B52 A52 +1.5V PWR DVOB_Fld/Stl B53 A53 DVOBC_ClkInt DVOB_D10 B54 A54 DVOB_D11 PWR GND B55 A55 GND PWR DVOB_D8 B56 A56 DVOB_D9 DVOB_D6 B57 A57 DVOB_D7 PWR +1.5V B58 A58 +1.5V PWR DVOB_Clk+ B59 A59 DVOB_Clk- DVOB_D4 B60 A60 DVOB_D5 PWR GND B61 A61 GND PWR DVOB_D2 B62 A62 DVOB_D3 DVOB_D0 B63 A63 DVOB_D1 PWR +1.5V B64 A64 +1.5V PWR DVOB-Vsync B65 A65 DVOB_Hsync VREFCG B66 A66 NC

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 24 of 71

Signal Description – (AGP)/DVO Connector:

Signal Description

DVOB_CLK; DVOB_CLK#

DVOB_D[11:0]

DVOB_HSYNC

DVOB_VSYNC

DVOB_BLANK#

DVOBC_CLKINT#

DVOB_FLDSTL

DVOC_CLK; DVOC_CLK#

DVOC_D[11:0]

DVOC_HSYNC

DVOC_VSYNC

DVOC_BLANK#

DVOBC_INTR#

DVOC_FLDSTL

M_I2CCLK

M_I2CDATA

M_DVI_CLK

M_DVI_DATA

M_DDCCLK

M_DDCDATA

ADD_ID[7:0]

DVOB Clock Output: These signals provide a differential pair reference clock that can run up to 165 MHz. Formerly known by: DVOB_CLKOUT0=DVOB_CLK and DVOB_CLKOUT1=DVOB_CLK#. Care should be taken to be sure that DVOB_CLK is connected to the primary clock receiver of the Intel® DVO device. DVOB Data: This data bus is used to drive 12-bit pixel data on each edge of DVOB_CLK(#). This provides 24 bits of data per clock. Horizontal Sync: This is the HSYNC signal for the DVOB interface. The active polarity of the signal is programmable. Vertical Sync: This is the VSYNC signal for the DVOB interface. The active polarity of the signal is programmable. Flicker Blank or Border Period Indication: DVOB_BLANK# is a programmable output pin driven by the GMCH. When programmed as a blank period indication, this pin indicates active pixels excluding the border. When programmed as a border period indication, this pin indicates active pixel including the border pixels. DVOBC Pixel Clock Input/Interrupt: This signal may be selected as the reference input to the dot clock PLL (DPLL) for the multiplexed DVO devices. This pin may also be programmed to be an interrupt input for either of the multiplexed DVO devices. TV Field and Flat Panel Stall Signal: This input can be programmed to be either a TV Field input from the TV encoder or Stall input from the flat panel. When used as a Field input, it synchronizes the overlay field with the TV encoder field when the overlay is displaying an interleaved source. When used as the Stall input, it indicates that the pixel pipeline should stall one horizontal line. The polarity is programmable for both modes and the input may be disabled completely. DVOC Clock Output: These pins provide a differential pair reference clock that can run up to 165 MHz. Formerly known by: DVOC_CLKOUT0=DVOC_CLK and DVOC_CLKOUT1=DVOC_CLK#. Care should be taken to be sure that DVOC_CLK is connected to the primary clock receiver of the DVO device. DVOC Data: This data bus is used to drive 12-bit pixel data on each edge of DVOC_CLK(#). This provides 24 bits of data per clock. Horizontal Sync: This is the HSYNC signal for the DVOC interface. The active polarity of the signal is programmable. Vertical Sync: This is the VSYNC signal for the DVOC interface. The active polarity of the signal is programmable. Flicker Blank or Border Period Indication: DVOC_BLANK# is a programmable output pin driven by the GMCH. When programmed as a blank period indication, this signal indicates active pixels excluding the border. When programmed as a border period indication, this signal indicates active pixel including the border pixels. DVOBC Interrupt: This signal may be used as an interrupt input for either of the multiplexed DVO devices. TV Field and Flat Panel Stall Signal: This input can be programmed to be either a TV Field input from the TV encoder or Stall input from the flat panel. When used as a Field input, it synchronizes the overlay field with the TV encoder field when the overlay is displaying an interleaved source. When used as the Stall input, it indicates that the pixel pipeline should stall one horizontal line. The polarity is programmable for both modes and the input may be disabled completely. MI2C_CLK: The specific function of this signal is I2C_CLK for a multiplexed digital display. This signal is tri-stated during a hard reset. MI2C_DATA: The specific function of this signal is I2C_DATA for a multiplexed digital display. This signal is tri-stated during a hard reset. MDVI_CLK: The specific function is DVI_CLK (DDC) for a multiplexed digital display connector. This signal is tri-stated during a hard reset. MDVI_DATA: The specific function of this signal is DVI_DATA (DDC) for a multiplexed digital display connector. This signal is tri-stated during a hard reset. MDDC_CLK: This signal may be used as the DDC_CLK for a secondary multiplexed digital display connector. This signal is tri-stated during a hard reset. MDDC_DATA: This signal may be used as the DDC_Data for a secondary multiplexed digital display connector. This signal is tri-stated during a hard reset. ADD Card ID: These signals will be strapped on the ADD card for software identification purposes. These signals may need pull-up or pull-down resistors in a DVO device down scenario.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 25 of 71

4.5 Parallel ATA harddisk interface

Two parallel ATA harddisk controllers are available on the board – a primary and a secondary controller. Standard 3½” harddisks or CD-ROM drives may be attached to the primary and secondary controller board by means of the 40 pin IDC connectors, IDE_P and IDE_S.

The harddisk controllers support Bus master IDE, ultra DMA 33/66/100 MHz and standard operation modes.

The signals used for the harddisk interface are the following:

DA*2..0 Address lines, used to address the I/O registers in the IDE hard disk.

HDCS*1..0# Hard Disk Chip-Select. HDCS0# selects the primary hard disk.

D*15..8 High part of data bus.

D*7..0 Low part of data bus.

IOR*# I/O Read.

IOW*# I/O Write.

IORDY*# This signal may be driven by the hard disk to extend the current I/O cycle.

RESET*# Reset signal to the hard disk.

HDIRQ* Interrupt line from hard disk.

CBLID* This input signal (CaBLe ID) is used to detect the type of attached cable: 80-wire cable

when low input and 40-wire cable when 5V via 10Kohm (pull-up resistor).

DDREQ* Disk DMA Request might be driven by the IDE hard disk to request bus master access to

the PCI bus. The signal is used in conjunction with the PCI bus master IDE function and is not associated with any PC-AT bus compatible DMA channel.

DDACK*# Disk DMA Acknowledge. Active low signal grants IDE bus master access to the PCI bus.

HDACT*# Signal from hard disk indicating hard disk activity. The signal level depends on the hard

disk type, normally active low. The signals from primary and secondary controller are routed together through diodes and passed to the connector FEATURE.

“*” is “A” for primary and “B” for secondary controller. The pinout of the connectors are defined in the following sections.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 26 of 71

4.5.1 IDE Hard Disk Connector (IDE_P)

This connector can be used for connection of up till two primary IDE drives.

Note

Pull U/D

- TBD O RESETA# 1 2 GND PWR - -

- TBD IO DA7 3 4 DA8 IO TBD -

- TBD IO DA6 5 6 DA9 IO TBD -

- TBD IO DA5 7 8 DA10 IO TBD -

- TBD IO DA4 9 10 DA11 IO TBD -

- TBD IO DA3 11 12 DA12 IO TBD -

- TBD IO DA2 13 14 DA13 IO TBD -

- TBD IO DA1 15 16 DA14 IO TBD -

- TBD IO DA0 17 18 DA15 IO TBD -

- - PWR GND 19 20 KEY - - -

- - I DDRQA 21 22 GND PWR - -

- TBD O IOWA# 23 24 GND PWR - -

- TBD O IORA# 25 26 GND PWR - - 4K7 - I IORDYA 27 28 GND PWR - -

- - O DDACKA# 29 30 GND PWR - - 10K - I HDIRQA 31 32 NC - - -

- TBD O DAA1 33 34 CBLIDA# I /15K

- TBD O DAA0 35 36 DAA2 O TBD -

- TBD O HDCSA0# 37 38 HDCSA1# O TBD -

- - I HDACTA# 39 40 GND PWR - -

Ioh/Iol Type Signal PIN Signal Type Ioh/Iol

Pull U/D

Note

4.5.2 IDE Hard Disk Connector (IDE_S)

This connector can be used for connection of up till two secondary IDE drive(s).

Note

Pull U/D

- TBD O RESETB# 1 2 GND PWR - -

- TBD IO DB7 3 4 DB8 IO TBD -

- TBD IO DB6 5 6 DB9 IO TBD -

- TBD IO DB5 7 8 DB10 IO TBD -

- TBD IO DB4 9 10 DB11 IO TBD -

- TBD IO DB3 11 12 DB12 IO TBD -

- TBD IO DB2 13 14 DB13 IO TBD -

- TBD IO DB1 15 16 DB14 IO TBD -

- TBD IO DB0 17 18 DB15 IO TBD -

- - PWR GND 19 20 KEY - - -

- - I DDRQB 21 22 GND PWR - -

- TBD O IOWB# 23 24 GND PWR - -

- TBD O IORB# 25 26 GND PWR - - 4K7 - I IORDYB 27 28 GND PWR - -

- - O DDACKB# 29 30 GND PWR - - /10K - I HDIRQB 31 32 NC - - -

- TBD O DAB1 33 34 CBLIDB# I -

- TBD O DAB0 35 36 DAB2 O TBD -

- TBD O HDCSB0# 37 38 HDCSB1# O TBD -

- - I HDACTB# 39 40 GND PWR - -

Ioh/Iol Type Signal PIN Signal Type Ioh/Iol

Pull U/D

Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 27 of 71

4.6 Serial ATA harddisk interface

Two serial ATA harddisk controllers are available on the board – a primary controller (SATA0) and a secondary controller (SATA1).

4.6.1 SATA Hard Disk Connector (SATA0, SATA1)

SATA0, J16:

Key

1 GND PWR - - 2 SATA0 TX+ 3 SATA0 TX- 4 GND PWR - - 5 SATA0 RX- 6 SATA0 RX+ 7 GND PWR - -

The signals used for the primary Serial ATA harddisk interface are the following:

SATA0 RX+

SATA0 RX-

SATA0 TX+

SATA0 TX-

All of the above signals are compliant to [4].

SATA1, J15:

Key

1 GND PWR - - 2 SATA1 TX+ 3 SATA1 TX- 4 GND PWR - - 5 SATA1 RX- 6 SATA1 RX+ 7 GND PWR - -

The signals used for the secondary Serial ATA harddisk interface are the following:

SATA1 RX+

SATA1 RX-

SATA1 TX+

SATA1 TX-

All of the above signals are compliant to [4].

Signal

Host transmitter differential signal pair

Host receiver differential signal pair

Signal

Host transmitter differential signal pair

Host receiver differential signal pair

Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 28 of 71

4.7 Floppy Disk Connector (FDC1)

Pull

Note

Signal Description:

RDATA# Read Disk Data, active low, serial data input from the floppy disk drive.

WDATA# Write Disk Data, active low, serial data output to the floppy disk drive.

WGATE# This output signal enables the head of the selected disk drive to write to the disk.

MOTEA# This output signal enables the motor in floppy disk drive A.

MOTEB# This output signal enables the motor in floppy disk drive B.

DRVA# Active low output signal to select floppy disk drive A.

DRVB# Active low output signal to select floppy disk drive B.

SIDE1# This output signal selects side of the disk in the selected drive.

DIR# This signal controls the direction of the floppy disk drive head movement during a seek

STEP# This output signal supplies step pulses to move the head during seek operations.

DENSEL0# This output indicates whether a low data rate (250/300kbps at low level) or a high data

TRK0# Floppy Disk Track 0, active low input to indicate that the head of the selected drive is at

INDEX# Floppy Disk Index, active low input indicates the beginning of a disk track.

WPT# Active low input signal indicating that the selected drive contains a write protected disk.

DSKCHG# Input pin that senses whether the drive door has been opened or the diskette has been

U/D Ioh/Iol Type

- - PWR GND 1 2 DENSEL0# OC /48 -

- - PWR GND 3 4 NC - - -

- - PWR GND 5 6 DS1# - - -

- - PWR GND 7 8 INDEX# IS - 330R

- - PWR GND 9 10 MOTEA# OC /48 -

- - PWR GND 11 12 DRVB# OC /48 -

- - PWR GND 13 14 DRVA# OC /48 -

- - PWR GND 15 16 MOTEB# OC /48 -

- - PWR GND 17 18 DIR# OC /48 -

- - PWR GND 19 20 STEP# OC /48 -

- - PWR GND 21 22 WDATA# OC /48 -

- - PWR GND 23 24 WGATE# OC /48 -

- - PWR GND 25 26 TRK0# IS - 330R

- - PWR GND 27 28 WPT# IS - 330R NC 29 30 RDATA# IS - 330R

- - PWR GND 31 32 SIDE1# OC /48 - NC 33 34 DSKCHG# IS - 330R

operation. A low level request steps through centre.

rate (500/1000kbps at high level) has been selected.

track 0.

changed.

Signal

Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 29 of 71

4.8 Printer Port Connector (PRINTER).

The printer port connector is provided in a standard DB25 pinout. The signal definition in standard printer port mode is as follows:

Pull

Note

2K2 (24)/24 OC(O) STB# 1

14 AFD# OC(O) (24)/24 2K2 2K2 24/24 IO PD0 2 15 ERR# I - 2K2 2K2 24/24 IO PD1 3 16 INIT# OC(O) (24)/24 2K2 2K2 24/24 IO PD2 4 17 SLIN# OC(O) (24)/24 2K2 2K2 24/24 IO PD3 5 18 GND PWR - - 2K2 24/24 IO PD4 6 19 GND PWR - - 2K2 24/24 IO PD5 7 20 GND PWR - - 2K2 24/24 IO PD6 8 21 GND PWR - - 2K2 24/24 IO PD7 9 22 GND PWR - - 2K2 - I ACK# 10 23 GND PWR - - 2K2 - I BUSY 11 24 GND PWR - - 2K2 - I PE 12 25 GND PWR - -

U/D Ioh/Iol Type

2K2 - I SLCT 13

The interpretation of the signals in standard Centronics mode (SPP) with a printer attached is as follows:

PD7..0 Parallel data bus from PC board to printer. The data lines are able to operate in PS/2

compatible bi-directional mode.

SLIN# Signal to select the printer sent from CPU board to printer.

SLCT Signal from printer to indicate that the printer is selected.

STB# This signal indicates to the printer that data at PD7..0 are valid.

BUSY Signal from printer indicating that the printer cannot accept further data.

ACK# Signal from printer indicating that the printer has received the data and is ready to accept

further data.

INIT# This active low output initializes (resets) the printer.

AFD# This active low output causes the printer to add a line feed after each line printed.

ERR# Signal from printer indicating that an error has been detected.

PE# Signal from printer indicating that the printer is out of paper.

The printer port additionally supports operation in the EPP and ECP mode as defined in [3].

Signal

Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 30 of 71

4.9 Serial Ports

Two RS232 serial ports (EIA/TIA-232-E compliant) are available on the 886LCD/ATX(GV) and 886LCD/ATXU(GV).

The typical interpretation of the signals in the COM ports is as follows:

TxD Serial output. This signal sends serial data to the communication link. The signal is set to a

marking state on hardware reset when the transmitter is empty or when loop mode operation is initiated.

RxD Serial input. This signal receives serial data from the communication link.

DTR Data Terminal Ready. This signal indicates to the modem or data set that the on-board UART is

ready to establish a communication link.

DSR Data Set Ready. This signal indicates that the modem or data set is ready to establish a

communication link.

RTS Request To Send. This signal indicates to the modem or data set that the on-board UART is ready

to exchange data.

CTS Clear To Send. This signal indicates that the modem or data set is ready to exchange data.

DCD Data Carrier Detect. This signal indicates that the modem or data set has detected the data

carrier.

RI Ring Indicator. This signal indicates that the modem has received a telephone-ringing signal.

The connector pinout for each operation mode is defined in the following sections.

4.9.1 Serial Port Com1 DB9 Connector.

Pull

Note

U/D Ioh/Iol Type

- - PWR GND 5

9 RI I - -

- O DTR 4 8 CTS I - -

- O TxD 3 7 RTS O -

- - I RxD 2 6 DSR I - -

- - I DCD 1

Signal

Type Ioh/Iol

Pull U/D Note

4.9.2 Serial Port Com2 Pin Header Connectors.

The pinout of Serial ports Com2 is as follows:

Pull

Note

If the DB9 adapter (ribbon cable) is used, the DB9 pinout will be identical to the pinout of Serial Com1

U/D Ioh/Iol Type

- I DCD 1 2 RxD I -

- I TxD 3 4 DTR O -

- O GND 5 6 DSR I -

- O RTS 7 8 CTS I -

- - PWR RI 9 10 NC - -

Signal

Signal Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 31 of 71

4.10 Ethernet connector.

The 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards supports 1 channel of 10/100Mb Ethernet using the Realtek 8100C LAN controller.

In order to achieve the specified performance of the Ethernet port, Category 5 twisted pair cables must be used with 10/100MB LAN networks.

The signals for the Ethernet ports are as follows:

TXD+

TXD-

RXD+

RXD-

Transmit pair in 10Base-T and 100Base-TX mode.

Receive pair in 10Base-T and 100Base-TX mode.

4.10.1 Ethernet connector (ETHER)

The Ethernet connector is mounted together with USB Ports 4 and 5.

The pinout of the RJ45 connector is as follows:

Signal PIN Type Ioh/Iol Note

TXD+

TXD-

RXD+

RXD-

8 7654321

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 32 of 71

4.11 USB Connector (USB)

The 886LCD/ATX(GV) and 886LCD/ATXU(GV) contains three USB (Universal Serial Bus) ports UHCI Host Controllers. Each Host Controller includes a root hub with two separate USB ports each, for a total of 6 USB ports.

The USB Host Controllers support the standard Universal Host Controller Interface (UHCI) Specification, Rev 1.1. All 6 USB ports support both USB1.0 and USB2.0 signaling.

Over-current detection on all six USB ports is supported.

USB Port 0 and 1 are supplied on the separate Rear IO connector. USB Port 4 and 5 are supplied on the combined ETHER, USB4, USB5 connector. USB Ports 2 and 3 are supplied on the USB2/3 connector.

4.11.1 USB Connector 0/1 (USB0/1)

USB0 and USB 1 are located on a separate Rear IO connector (I/O Bracket connector).

Pull

Note

Note 1: The 5V supply for the USB devices is on-board fused with a 1.5A reset-able fuse. The supply is

common for the two channels. SB5V is supplied during power down to allow wakeup on USB device activity. In order to meet the requirements of USB v.1.1 standard, the 5V input supply must be at least 5.00V.

USB0+ USB0-

USB1+ USB1-

USB5V 5V supply for external devices. Fused with 1.5A reset-able fuse.

U/D Ioh/Iol Type

1 2 3 4

1 - - PWR 5V/SB5V GND PWR - -

/15K 0.25/2 IO USB0- USB0+ IO 0.25/2 /15K 1 2 3 4

1 - - PWR 5V/SB5V GND PWR - -

/15K 0.25/2 IO USB1- USB1+ IO 0.25/2 /15K

Differential pair works as Data/Address/Command Bus.

Signal

Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 33 of 71

4.11.2 USB Connector 2/3 (USB2/3).

USB2 and USB3 are located on a a 2x5 pinrow connector.

The pinout of the USB2/3 connector (USB2) is as follows:

Pull

Note

Note 1: The 5V supply for the USB devices is on-board fused with a 1.5A reset-able fuse. The supply is

common for the two channels. SB5V is supplied during power down to allow wakeup on USB device activity. In order to meet the requirements of USB v.1.1 standard, the 5V input supply must be at least 5.00V.

USB2+ USB2-

USB3+ USB3-

USB5V 5V supply for external devices. Fused with 1.5A reset-able fuse.

U/D Ioh/Iol Type

1 PWR 5V/SB5V 1 2 5V/SB5V PWR 1

/15K 0.25/2 IO USB2- 3 4 USB3- IO 0.25/2 /15K /15K 0.25/2 IO USB2+ 5 6 USB3+ IO 0.25/2 /15K PWR GND 7 8 GND PWR PWR GND 9 10 NC

Differential pair works as Data/Address/Command Bus.

Signal

Signal Type Ioh/Iol

Pull U/D Note

4.11.3 USB Connector 4/5 (USB4/5)

USB4 and USB5 are mounted together with ETHER ethernet port on a Rear IO connector (I/O Bracket connector).

Pull

Note

Note 1: The 5V supply for the USB devices is on-board fused with a 1.5A reset-able fuse. The supply is

common for the two channels. SB5V is supplied during power down to allow wakeup on USB device activity. In order to meet the requirements of USB v.1.1 standard, the 5V input supply must be at least 5.00V.

USB4+ USB4-

USB5+ USB5-

USB5V 5V supply for external devices. Fused with 1.5A reset-able fuse.

U/D Ioh/Iol Type

1 2 3 4

1 - - PWR 5V/SB5V GND PWR - -

/15K 0.25/2 IO USB4- USB4+ IO 0.25/2 /15K 1 2 3 4

1 - - PWR 5V/SB5V GND PWR - -

/15K 0.25/2 IO USB5- USB5+ IO 0.25/2 /15K

Differential pair works as Data/Address/Command Bus.

Signal

Type Ioh/Iol

Pull U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 34 of 71

4.12 Audio Connector

4.12.1 Audio Line-in, Line-out and Microphone

Audio Line-in, Line-out and Microphone are available in the stacked audio jack connector.

IN Signal Type Note

TIP Line in – Left IA 1

RING Line in – Right IA 1

SLEEVE GND PWR

TIP Line out – Left OA

RING Line out – Right OA

SLEEVE GND PWR

TIP Mic1 IA 1

RING

SLEEVE GND PWR

Note 1: Signals are shorted to GND internally in the connector, when jack-plug is not inserted.

4.12.2 CD-ROM Audio input (CDROM)

CD-ROM audio input may be connected to this connector. It may also be used as a secondary line-in signal.

PIN Signal Type Ioh/Iol Pull

1 CD_Left IA - - 2 CD_GND IA - - 3 CD_GND IA - - 4 CD_Right IA - -

CD_Left CD_Right

CD_GND Analogue GND for Left and Right CD.

Left and right CD audio input lines or secondary Line-in.

(This analogue GND is not shorted to the general digital GND on the board).

U/D

Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 35 of 71

4.13 Fan connectors, CPU FAN, CHASSIS FAN, PWR FAN.

The CPU FAN (FAN3) is used for connection of the active cooler for the CPU. The CHASSIS FAN (FAN2) can be used to power, control and monitor a fan for chassis ventilation etc.

1 SENSE - 1K 2 12V_PWM PWR - - 3 GND PWR - -

Signal description:

12V_PWM +12V supply for fan, can be turned on/off or modulated (PWM) by the chipset.

A maximum of 1000 mA can be supplied from this pin.

SENSE Tacho signal from the fan for supervision. The signals shall be generated by an open

collector transistor or similar. On board is a pull-up resistor 1K to +5V. The signal has to be pulses, typically 2 Hz per rotation.

The PWR FAN (FAN1) can be used for high power fans.

1 SENSE - 1K 2 12V PWR - - 3 GND PWR - -

Signal description:

12V +12V supply for fan. A maximum of 2000 mA can be supplied from this pin.

SENSE Tacho signal from the fan for supervision. The signals shall be generated by an open

collector transistor or similar. On board is a pull-up resistor 1K to +5V. The signal has to be pulses, typically 2 Hz per rotation.

Signal

Type Ioh/Iol

Pull U/D

Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 36 of 71

4.14 The Clear CMOS Jumper, Clr-CMOS.

The Clear CMOS Jumper is used to clear the CMOS content.

To clear all CMOS settings, including Password protection, move the Clear CMOS jumper (with or without power on the system) for approximately 1 minute.

Alternatively if no jumper is available, turn off power and remove the battery for 1 minute, but be careful to orientate the battery correctly when reinserted.

4.15 Front Side Bus Speed, FSB

Select CPU base clock to one of 3 options by configuring the FSB jumper row (JP5) as shown below.

The CPU used has itself output signals that indicate what the maximum/default frequency to be used is. Please also note that the CPU internal clock multiplier is fixed by the manufacturer.

“CPU select”: Will let the CPU / BIOS automatically control the base clock (default). “100MHz setting”: Will force CPU input clock to 100MHz and the internal CPU clock and FSB will be set

accordingly. CPU clock = 100MHz x Clock multiplier FSB clock = 400MHz

“133MHz setting”: Will force CPU input clock to 133MHz and the internal CPU clock and FSB will be set

accordingly. CPU clock = 133MHz x Clock multiplier FSB clock = 533MHz

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 37 of 71

4.16 Case Open, S1

The Case Open connector can be used for Intrusion Detection. If Case is opened the switch should be closed.

Pull

Note

U/D Ioh/Iol Type

PWR GND 1 2 CASEOPEN# I 220K

Signal

Type Ioh/Iol

Pull U/D Note

4.17 Trusted Platform Module (TPM) connector, CN7 (unsupported).

Pull

Note

U/D Ioh/Iol Type

CLK CLK_33MHz 1 2 GND PWR LFRAME# 3 4 NC LRESET# 5 6 5V/SB5V PWR LAD3 7 8 LAD2 PWR VCC3 9 10 LAD1 LAD0 11 12 GND PWR SMCLK 13 14 SMDATA PWR VCC3SB 15 16 GPIO PWR GND 17 18 SERIRQ SUS_STAT# 19 20 LDRQ#

Signal

Type Ioh/Iol

Pull

U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 38 of 71

4.18 Front Panel connector, CN5.

Pull

Note

U/D Ioh/Iol Type

330 PWR GRN LED+ 1 2 PWR LED+ PWR 330 330 PWR GRN LED+ 3 4 PWR LED+ PWR 330 O GRN LED- 5 6 GND PWR 330 PWR HDD LED+ 7 8 KBLOCK# I O HDD LED- 9 10 GND PWR O HDD LED- 11 12 SLEEP# I 330 PWR HDD LED+ 13 14 GND PWR I RESET# 15 16 +5V PWR PWR GND 17 18 GND PWR I PWRSW 19 20 GND PWR PWR 5V/SB5V 21 22 SPKR O

Signal Description

GRN LED

PWR LED ATX Power LED. LED for showing ATX Power On

HDD LED HDD LED for showing SATA or PATA activity

KBLOCK# Keyboard Lock Switch. Active low signal will cause keyboard to be locked

SLEEP# Suspend Switch Connector.

RESET# Reset Switch Connector.

PWRSW ATX Power Switch Connector

5V/SB5V Standby 5V or ATX Power 5V depending on power state.

SPKR Chassis Speaker Connector

Green Status LED. When the system is in Suspend, the green LED will flash. When the system is in normal working mode, the Green LED will be Off.

Signal

Type Ioh/Iol

Pull

U/D Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 39 of 71

4.19 GAME / MIDI Connector, CN6

Pull

Note

U/D Ioh/Iol Type

PWR VCC 1 2 VCC PWR J1BUTTON1 3 4 J2BUTTON1 J1X 5 6 J2X PWR GND 7 8 MIDI_OUT PWR GND 9 10 J2Y J1Y 11 12 J2BUTTON2 J1BUTTON2 13 14 MIDI_IN PWR VCC 15 16 NC

Signal Description

J1BUTTON1 Active-low, Joystick I switch input 1

J2BUTTON1 Active-low, Joystick II switch input 1

J1X Joystick I timer pin. This pin connect to X positioning variable resistors for the Joystick

J2X Joystick II timer pin. This pin connect to X positioning variable resistors for the Joystick

J1Y Joystick II timer pin. This pin connect to Y positioning variable resistors for the Joystick

J2Y Joystick I timer pin. This pin connect to Y positioning variable resistors for the Joystick

J1BUTTON2 Active-low, Joystick II switch input 2. This pin has an internal pullup resistor

J2BUTTON2 Active-low, Joystick I switch input 2. This pin has an internal pullup resistor

MIDI_IN MIDI serial data input

Signal

Type Ioh/Iol

Pull

U/D Note

4.20 IR Connector (IR1).

Pull

Note

U/D Ioh/Iol Type

PWR VCC 1 NC 2 I IRRX 3 PWR GND 4 O IRTX 5

Signal Description

IRRX

IRTX

Infrared receive signal. Support IrDA version 1.0 SIR Protocol with maximum baudrate up to 115.2 K bps Infrared transmit signal Support IrDA version 1.0 SIR Protocol with maximum baudrate up to 115.2 K bps

Signal

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 40 of 71

4.21 WOL Connector (W.O.L).

Pull

Note

U/D Ioh/Iol Type

PWR 5V/SB5V 1 PWR GND 2 I PME# 3

Signal Description

Wake on LAN from an external LAN adapter is supported through this signal. Connect

PME#

5V/SB5V Standby 5V or ATX Power 5V depending on power state.

the W.O.L. signals from the adapter to this connector and install software to support W.O.L.

Signal

4.22 JP3 (optional).

Pull

Note

U/D Ioh/Iol Type

I R-NTC 1 I R-NTC 2

Signal Description

R-NTC

Option for connection of external temperature sensor based on NTC Resistor 150mW 10Kohm or simialar.

Signal

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 41 of 71

4.23 PCI Slot 1, Slot 2 and Slot 3 connectors.

4.23.1 PCI Slot Connector

Note Type Signal

PWR -12V F01 E01 TRST# O O TCK F02 E02 +12V PWR PWR GND F03 E03 TMS O I TDO F04 E04 TDI O PWR +5V F05 E05 +5V PWR PWR +5V F06 E06 INTA# I I INTB# F07 E07 INTC# I I INTD# F08 E08 +5V PWR I REQ2# F09 E09 CLKC O I REQ3# F10 E10 +5V (I/O) PWR OT GNT2# F11 E11 CLKD O PWR GND F12 E12 GND PWR PWR GND F13 E13 GND PWR O CLKA F14 E14 GNT3# OT PWR GND F15 E15 RST# O O CLKB F16 E16 +5V (I/O) PWR PWR GND F17 E17 GNT0# OT I REQ0# F18 E18 GND PWR PWR +5V (I/O) F19 E19 REQ1# I IOT AD31 F20 E20 AD30 IOT IOT AD29 F21 E21 +3.3V PWR PWR GND F22 E22 AD28 IOT IOT AD27 F23 E23 AD26 IOT IOT AD25 F24 E24 GND PWR PWR +3.3V F25 E25 AD24 IOT IOT C/BE3# F26 E26 GNT1# OT IOT AD23 F27 E27 +3.3V PWR PWR GND F28 E28 AD22 IOT IOT AD21 F29 E29 AD20 IOT IOT AD19 F30 E30 GND PWR

PWR +3.3V F31 E31 AD18 IOT

IOT AD17 F32 E32 AD16 IOT IOT C/BE2# F33 E33 +3.3V PWR PWR GND F34 E34 FRAME# IOT IOT IRDY# F35 E35 GND PWR PWR +3.3V F36 E36 TRDY# IOT IOT DEVSEL# F37 E37 GND PWR PWR GND F38 E38 STOP# IOT IOT LOCK# F39 E39 +3.3V PWR IOT PERR# F40 E40 SDONE IO PWR +3.3V F41 E41 SB0# IO IOC SERR# F42 E42 GND PWR PWR +3.3V F43 E43 PAR IOT IOT C/BE1# F44 E44 AD15 IOT IOT AD14 F45 E45 +3.3V PWR PWR GND F46 E46 AD13 IOT IOT AD12 F47 E47 AD11 IOT IOT AD10 F48 E48 GND PWR PWR GND F49 E49 AD09 IOT

SOLDER SIDE COMPONENT SIDE

IOT AD08 F52 E52 C/BE0# IOT IOT AD07 F53 E53 +3.3V PWR PWR +3.3V F54 E54 AD06 IOT IOT AD05 F55 E55 AD04 IOT IOT AD03 F56 F56 GND PWR PWR GND F57 E57 AD02 IOT IOT AD01 F58 E58 AD00 IOT PWR +5V (I/O) F59 E59 +5V (I/O) PWR IOT ACK64# F60 E60 REQ64# IOT PWR +5V F61 E61 +5V PWR PWR +5V F62 E62 +5V PWR

Terminal

S C

Signal Type Note

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 42 of 71

4.23.2 Signal Description –PCI Slot Connector

SYSTEM PINS

CLK

RST#

ADDRESS AND DATA

AD[31::00]

C/BE[3::0]#

PAR

INTERFACE CONTROL PINS

FRAME#

IRDY#

TRDY#

STOP#

LOCK#

IDSEL

DEVSEL#

Clock provides timing for all transactions on PCI and is an input to every PCI device. All other PCI signals, except RST#, INTA#, INTB#, INTC#, and INTD#, are sampled on the rising edge of CLK and all other timing parameters are defined with respect to this edge. PCI operates at 33 MHz. Reset is used to bring PCI-specific registers, sequencers, and signals to a consistent state. What effect RST# has on a device beyond the PCI sequencer is beyond the scope of this specification, except for reset states of required PCI configuration registers. Anytime RST# is asserted, all PCI output signals must be driven to their benign state. In general, this means they must be asynchronously tri-stated. SERR# (open drain) is floated. REQ# and GNT# must both be tri-stated (they cannot be driven low or high during reset). To prevent AD, C/BE#, and PAR signals from floating during reset, the central resource may drive these lines during reset (bus parking) but only to a logic low level–they may not be driven high. RST# may be asynchronous to CLK when asserted or deasserted. Although asynchronous, deassertion is guaranteed to be a clean, bounce-free edge. Except for configuration accesses, only devices that are required to boot the system will respond after reset.

Address and Data are multiplexed on the same PCI pins. A bus transaction consists of an address phase followed by one or more data phases. PCI supports both read and write bursts. The address phase is the clock cycle in which FRAME# is asserted. During the address phase AD[31::00] contain a physical address (32 bits). For I/O, this is a byte address; for configuration and memory, it is a DWORD address. During data phases AD[07::00] contain the least significant byte (lsb) and AD[31::24] contain the most significant byte (msb). Write data is stable and valid when IRDY# is asserted and read data is stable and valid when TRDY# is asserted. Data is transferred during those clocks where both IRDY# and TRDY# are asserted. Bus Command and Byte Enables are multiplexed on the same PCI pins. During the address phase of a transaction, C/BE[3::0]# define the bus command. During the data phase C/BE[3::0]# are used as Byte Enables. The Byte Enables are valid for the entire data phase and determine which byte lanes carry meaningful data. C/BE[0]# applies to byte 0 (lsb) and C/BE[3]# applies to byte 3 (msb). Parity is even parity across AD[31::00] and C/BE[3::0]#. Parity generation is required by all PCI agents. PAR is stable and valid one clock after the address phase. For data phases, PAR is stable and valid one clock after either IRDY# is asserted on a write transaction or TRDY# is asserted on a read transaction. Once PAR is valid, it remains valid until one clock after the completion of the current data phase. (PAR has the same timing as AD[31::00], but it is delayed by one clock.) The master drives PAR for address and write data phases; the target drives PAR for read data phases.

Cycle Frame is driven by the current master to indicate the beginning and duration of an access. FRAME# is asserted to indicate a bus transaction is beginning. While FRAME# is asserted, data transfers continue. When FRAME# is deasserted, the transaction is in the final data phase or has completed. Initiator Ready indicates the initiating agent’s (bus master’s) ability to complete the current data phase of the transaction. IRDY# is used in conjunction with TRDY#. A data phase is completed on any clock both IRDY# and TRDY# are sampled asserted. During a write, IRDY# indicates that valid data is present on AD[31::00]. During a read, it indicates the master is prepared to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. Target Ready indicates the target agent’s (selected device’s) ability to complete the current data phase of the transaction. TRDY# is used in conjunction with IRDY#. A data phase is completed on any clock both TRDY# and IRDY# are sampled asserted. During a read, TRDY# indicates that valid data is present on AD[31::00]. During a write, it indicates the target is prepared to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. Stop indicates the current target is requesting the master to stop the current transaction.

Lock indicates an atomic operation that may require multiple transactions to complete. When LOCK# is asserted, non-exclusive transactions may proceed to an address that is not currently locked. A grant to start a transaction on PCI does not guarantee control of LOCK#. Control of LOCK# is obtained under its own protocol in conjunction with GNT#. It is possible for different agents to use PCI while a single master retains ownership of LOCK#. If a device implements Executable Memory, it should also implement LOCK# and guarantee complete access exclusion in that memory. A target of an access that supports LOCK# must provide exclusion to a minimum of 16 bytes (aligned). Host bridges that have system memory behind them should implement LOCK# as a target from the PCI bus point of view and optionally as a master. Initialization Device Select is used as a chip select during configuration read and write transactions.

Device Select, when actively driven, indicates the driving device has decoded its address as the target of the current access. As an input, DEVSEL# indicates whether any device on the bus has been selected.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 43 of 71

ARBITRATION PINS (BUS MASTERS ONLY)

REQ#

GNT#

ERROR REPORTING PINS.

The error reporting pins are required by all devices and maybe asserted when enabled

PERR#

SERR#

INTERRUPT PINS (OPTIONAL).

Interrupts on PCI are optional and defined as “level sensitive,” asserted low (negative true), using open drain output drivers. The assertion and deassertion of INTx# is asynchronous to CLK. A device asserts its INTx# line when requesting attention from its device driver. Once the INTx# signal is asserted, it remains asserted until the device driver clears the pending request. When the request is cleared, the device deasserts its INTx# signal. PCI defines one interrupt line for a single function device and up to four interrupt lines for a multi-function device or connector. For a single function device, only INTA# may be used while the other three interrupt lines have no meaning.

INTA#

INTB#

INTC#

INTD#

Request indicates to the arbiter that this agent desires use of the bus. This is a point to point signal. Every master has its own REQ# which must be tri-stated while RST# is asserted. Grant indicates to the agent that access to the bus has been granted. This is a point to point signal. Every master has its own GNT# which must be ignored while RST# is asserted. While RST# is asserted, the arbiter must ignore all REQ# lines since they are tri-stated and do not contain a valid request. The arbiter can only perform arbitration after RST# is deasserted. A master must ignore its GNT# while RST# is asserted. REQ# and GNT# are tri-state signals due to power sequencing requirements when 3.3V or 5.0V only add-in boards are used with add-in boards that use a universal I/O buffer.

Parity Error is only for the reporting of data parity errors during all PCI transactions except a Special Cycle. The PERR# pin is sustained tri-state and must be driven active by the agent receiving data two clocks following the data when a data parity error is detected. The minimum duration of PERR# is one clock for each data phase that a data parity error is detected. (If sequential data phases each have a data parity error, the PERR# signal will be asserted for more than a single clock.) PERR# must be driven high for one clock before being tri-stated as with all sustained tri-state signals. There are no special conditions when a data parity error may be lost or when reporting of an error may be delayed. An agent cannot report a PERR# until it has claimed the access by asserting DEVSEL# (for a target) and completed a data phase or is the master of the current transaction. System Error is for reporting address parity errors, data parity errors on the Special Cycle command, or any other system error where the result will be catastrophic. If an agent does not want a nonmaskable interrupt (NMI) to be generated, a different reporting mechanism is required. SERR# is pure open drain and is actively driven for a single PCI clock by the agent reporting the error. The assertion of SERR# is synchronous to the clock and meets the setup and hold times of all bused signals. However, the restoring of SERR# to the deasserted state is accomplished by a weak pullup (same value as used for s/t/s) which is provided by the system designer and not by the signaling agent or central resource. This pull-up may take two to three clock periods to fully restore SERR#. The agent that reports SERR#s to the operating system does so anytime SERR# is sampled asserted.

Interrupt A is used to request an interrupt.

Interrupt B is used to request an interrupt and only has meaning on a multi-function device.

Interrupt C is used to request an interrupt and only has meaning on a multi-function device.

Interrupt D is used to request an interrupt and only has meaning on a multi-function device.

4.23.3 886LCD/ATX(GV) and 886LCD/ATXU(GV) PCI IRQ & INT routing

Board type Slot IDSEL INTA INTB INTC INTD 886LCD/ATXU(GV)

2 AD17 INT_PIRQ#G INT_PIRQ#F INT_PIRQ#E INT_PIRQ#H

3 AD18 INT_PIRQ#C INT_PIRQ#D INT_PIRQ#B INT_PIRQ#A

886LCD/ATX(GV)

2 AD17 INT_PIRQ#G INT_PIRQ#F INT_PIRQ#E INT_PIRQ#H

3 AD18 INT_PIRQ#C INT_PIRQ#D INT_PIRQ#B INT_PIRQ#A

4 AD19 INT_PIRQ#B INT_PIRQ#C INT_PIRQ#A INT_PIRQ#D

5 AD23 INT_PIRQ#H INT_PIRQ#E INT_PIRQ#F INT_PIRQ#G

6 AD25 INT_PIRQ#E INT_PIRQ#H INT_PIRQ#G INT_PIRQ#F

1 AD16 INT_PIRQ#F INT_PIRQ#G INT_PIRQ#H INT_PIRQ#E

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 44 of 71

5. System Resources

5.1 Memory map

The table below lists the system memory map.

Address range (hex) Size Description

00000000- 0007FFFF 512 Kbytes Conventional memory 00080000- 0009FBFF 127 Kbyte Extended conventional memory 0009FC00- 0009FFFF 1 Kbyte Extended BIOS data 000A0000- 000AFFFF 64 Kbytes 845 VGA Controller, Video memory and BIOS 000B0000- 000BFFFF 64 Kbytes 845 VGA Controller, Video memory and BIOS 000C0000- 000CBFFF 48 Kbytes 845 VGA Controller, Video memory and BIOS 000CC000- 000CDFFF 8 Kbytes Realtek 8100 Ethernet boot. F0000000- F7FFFFFF 0x8000000 845 VGA Controller FEC00000- FEC00FFF 0x1000 Motherboard resource (APIC) FEE00000- FEE00FFF 0x1000 Motherboard resource (APIC) FF8FF800- FF8FF8FF 0x100 Realtek 8100 Ethernet Controller FF8FFC00- FF8FFDFF 0x200 SATA/RAID controller FFA7F400- FFA7F7FF 0x400 USB Controller FFA7F800- FFA7F8FF 0x100 Realtek AC97 Audio FFA7FC00- FFA7FDFF 0x200 Realtek AC97 Audio FFA80000- FFAFFFFF 0x80000 845 VGA Controller FFB7FC00- FFB7FFFF 0x400 Ultra SATA Controller FFB80000- FFBFFFFF 0x80000 Intel 82802 Firmware Hub Device FFC00000- FFF7FFFF 0x380000 Motherboard reserved FFF80000- FFFFFFFF 0x80000 Intel 82802 Firmware Hub Device

5.2 PCI devices

Bus # Device # Function # Vendor ID Device ID IDSEL Chip Device Function

0 0 0 8086 2560 MCH Northbridge 0 2 0 8086 2562 MCH Graphics 0 29 0 8086 24C2 ICHS USB 0 29 1 8086 24C4 ICHS USB 0 29 2 8086 24C7 ICHS USB 0 29 7 8086 24CD ICHS USB 0 30 0 8086 244E ICHS PCI to PCI bridge 0 31 0 8086 24C0 ICHS ISA/LPC Bridge 0 31 1 8086 24CB ICHS IDE Controller 0 31 3 8086 24C3 ICHS SMBUS Controller 0 31 5 8086 24C5 ICHS Audio Device 1 0 - - - AD16 - PCI SLOT 1 1 1 - - - AD17 - PCI SLOT 2 1 2 - - - AD18 - PCI SLOT 3 1 3 - - - AD19 - PCI SLOT 4 1 4 0 1095 3512 AD20 SIL3512 SATA Controller 1 5 0 10EC 8139 AD21 RTL8100 Ethernet 1 7 - - - AD23 - PCI SLOT 5 1 9 - - - AD25 - PCI SLOT 6

Note: All PCI slots for the 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards support PCI BUS Mastering.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 45 of 71

5.3 Interrupt Usage

Onboard system parity errors and IOCHCHK signal activation

Onboard Timer 0 Interrupt

Onboard Keyboard Interrupt

Used for Cascading IRQ8-IRQ15

May be used by onboard Serial Port A

May be used by onboard Serial Port B / IrDA Port

May be used by onboard SATA controller

May be used by onboard Parallel Port

May be used by onboard Floppy disk Controller

Used by onboard Real Time Clock Alarm

May be used by onboard P/S 2 support

Used for Onboard co-processor support

May be used by primary harddisk controller

May be used by secondary harddisk controller

May be used for onboard Sound System

May be used by onboard USB controller

May be used by onboard Ethernet controller

May be used by onboard VGA Controller

May be used by onboard SMBus Controller

IRQ

NMI IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ20 IRQ21 IRQ22 IRQ23

•

• •

• • • • • •

• • • • •

•

• •

Available on PCI slots as IRQA-IRQH depending on selections in the BIOS

Notes

•

1,2 1,2 1,2

1,2

1,2 1,2 1,2

1

1 3 3 3 3 3 3 3 3

Notes:

1. Availability of the shaded IRQs depends on the setting in the BIOS. According to the PCI Standard, PCI Interrupts IRQA-IRQH can be shared.

2. These interrupt lines are managed by the PnP handler and are subject to change during system initialisation.

3. IRQ16 to IRQ23 are APIC interrupts

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 46 of 71

5.4 I/O Map

Address (hex) Size Description

0020- 0021 2 Programmable interrupt controller 0040- 0043 4 System Timer 0060- 0060 1 Standard keyboard 0061- 0061 1 System speaker 0070- 0071 2 System CMOS/Real time clock 0170- 01F7 8 Secondary Parallel ATA IDE Channel 01F0- 01F7 8 Primary Parallel ATA IDE Channel 02F8- 02FF 8 Comport 2 0378- 037F 8 Printer Port 03B0- 03BB 0xC 845 VGA Controller 03C0- 03DF 0x20 845 VGA Controller 03F8- 03FF 8 Comport 1 0CF8- 0CFF 8 PCI Bus D000- D0FF 0x100 Realtek 8100 Ethernet Controller D400- D40F 0x10 SATA/Raid Controller D480- D483 4 SATA/Raid Controller D800- D807 8 SATA/Raid Controller D880- D883 4 SATA/Raid Controller DC00- DC07 8 SATA/Raid Controller E000- E01F 0x20 Standard Universal PCI to USB Host Controller E080- E09F 0x20 Standard Universal PCI to USB Host Controller E400 E41F 0x20 Standard Universal PCI to USB Host Controller E480- E49F 0x20 PCI System Management Bus E800- E8FF 0x100 Realtek AC97 Audio EC00- EC3F 0x40 Realtek AC97 Audio FFA0- FFAF 0x10

Ultra ATA Controller

5.5 DMA Channel Usage

DMA Channel Number Data Width System Resources

0 8 or 16 bits Available 1 8 or 16 bits Available 2 8 or 16 bits Available 3 8 or 16 bits Available 4 8 or 16 bits DMA Controller 5 16 bits Available 6 16 bits Available 7 16 bits Available

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 47 of 71

6. Overview of BIOS features

This Manual section details specific BIOS features for the 886LCD/ATX(GV) and 886LCD/ATX(GV) boards. The BIOS are based on the AMI BIOS core version 8 with Kontron BIOS extensions.

6.1.1 System Management BIOS (SMBIOS / DMI)

SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network.

The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components. Using SMBIOS, a system administrator can obtain the system types, capabilities, operational status, and installation dates for system components.

The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as third-party management software to use SMBIOS.

The BIOS stores and reports the following SMBIOS information:

• BIOS data, such as the BIOS revision level

• Fixed-system data, such as peripherals, serial numbers, and asset tags

• Resource data, such as memory size, cache size, and processor speed

• Dynamic data, such as event detection and error logging

Non-Plug and Play operating systems, such as Windows NT, require an additional interface for obtaining the SMBIOS information. The BIOS supports an SMBIOS table interface for such operating systems. Using this support, an SMBIOS service-level application running on a non-Plug and Play operating system can obtain the SMBIOS information.

The 886LCD Boards support reading certain MIF specific details by the Windows API. Refer to the API section in this manual for details.

6.1.2 Legacy USB Support

Legacy USB support enables USB devices such as keyboards, mice, and hubs to be used even when the operating system’s USB drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB support is set to Enabled.

Legacy USB support operates as follows:

1. When you apply power to the computer, legacy support is disabled.

2. POST begins.

3. Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to enter and configure the BIOS Setup program and the maintenance menu.

4. POST completes.

5. The operating system loads. While the operating system is loading, USB keyboards and mice are recognized and may be used to configure the operating system. (Keyboards and mice are not recognized during this period if Legacy USB support was set to Disabled in the BIOS Setup program.)

6. After the operating system loads the USB drivers, all legacy and non-legacy USB devices are recognized by the operating system, and Legacy USB support from the BIOS is no longer used.

To install an operating system that supports USB, verify that Legacy USB support in the BIOS Setup program is set to Enabled and follow the operating system’s installation instructions.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 48 of 71

7. BIOS Configuration / Setup

7.1 Introduction

The BIOS Setup is used to view and configure BIOS settings for the 886LCD/ATX(GV) and 886LCD/ATXU(GV) boards. The BIOS Setup is accessed by pressing the DEL key after the Power-On SelfTest (POST) memory test begins and before the operating system boot begins.

The Menu bar is shown below:

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

The available keys for the Menu screens are as follows:

Function Key Description

<←> or <→> Select Screen <↑> or <↓> Select Item <+> or <-> Change Field <Tab> Select Field <F1> General Help <F10> Save and Exit <Esc> Exits the Menu

The following section lists the available BIOS setup information and features of the different Menus.

7.2 Main Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

System Overview AMIBIOS

Version : 08.00.10 Build Date: 10/18/05 ID : 886AT014 PCB ID : 01 Serial # : 00375748 Part # : 66610000

Processor

Type : Intel(R) Pentium(R) 4 CPU 2.4GHZ Speed : 2400MHz Count : 1

System Memory

Size : 1016MB

System Time [10:18:15] System Date [Mon 03/15/2006]

Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.

Use [+] or [-] to configure system Time.

<- Select Screen || Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit

Main Menu Selections

Feature Options Description

System Time HH:MM:SS Set the system time System Date MM/DD/YYYY Set the system date

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 49 of 71

7.3 Advanced Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Advanced Settings

Warning: Setting wrong values in below sections May cause system to malfunction.

>

CPU Configuration

>

IDE Configuration

>

Floppy Configuration

>

SuperIO Configuration

>

Hardware Health Configuration

>

ACPI Configuration

>

USB Configuration

Configure CPU.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

7.3.1 Advanced settings – CPU Configuration

BIOS Setup Utility

Advanced

Configure advanced CPU settings

Manufacturer: Intel Brand String: Intel (R) Pentium(R) CPU 2.40GHz Frequency : 2.40GHz FSB Speed : 533MHz

Cache L1 : 8 KB Cache L2 : 512 KB

Ratio Status :Locked Ratio Actual Value :18 Ratio CMOS Setting: [18] VID CMOS Setting : [62]

Max CPUID Value Limit: [Disabled]

Feature Options Description

Max CPUID Value Limit

Disabled,

Enabled

This should be enabled in order to boot legacy OSes that cannot Support CPUs with Extended CPUID Functions.

<- Select Screen || Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 50 of 71

7.3.2 Advanced settings – IDE Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

IDE Configuration

OnBoard PCI IDE Controller [Both]

Primary IDE Master : [Hard Disk] Primary IDE Slave : [Not Detected] Secondary IDE Master : [Not Detected] Secondary IDE Slave : [Not Detected]

Hard Disk Write Protect [Disabled] IDE Detect Time Out (Sec) [35] ATA(PI) 80Pin Cable Detection [Host & Device]

Feature Options Description

OnBoard PCI IDE Controller

Hard Disk Write Protect

IDE Detect Time Out (Sec) 0, 5, 10, 15, 20, 25,

ATA(PI) 80Pin Cable Detection

Disabled, Primary, Secondary,

Both Disable,

Enabled

30, 35 Host & Device,

Host, Device

Setup the configuration of the hard drive interfaces.

Enable write protection on HDDs, only works when it is accessed through the BIOS. Select the time out value when the BIOS is detecting ATA/ATAPI Devices. Select the mechanism for detecting 80Pin ATA Cable.

DISABLED: disables the integrated IDE Controller. PRIMARY: enables only The Primary IDE Controller. SECONDARY: enables Only the Secondary IDE Controller. BOTH: enables both IDE Controllers.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 51 of 71

BIOS Setup Utility

Advanced

Primary IDE Master

Device :Hard Disk Vendor :ST340014A Size :40.0GB LBA Mode :Supported Block Mode :16Sectors PIO Mode :4 Async DMA :MultiWord DMA-2 Ultra DMA :Ultra DMA-5 S.M.A.R.T. :Supported

Type [Auto] LBA/Large Mode [Auto] Block (Multi-Sector Transfer) [Auto] PIO Mode [Auto] DMA Mode [Auto] S.M.A.R.T. [Auto] 32Bit Data Transfer [Disabled]

Select the type of devices connected to the system

<- Select Screen || Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit

Feature Options Description

Type Not Installed,

Auto,

CDROM, ARMD

LBA/Large Mode Disabled,

Auto

Block (Multi-Sector Transfer) PIO Mode

DMA Mode

S.M.A.R.T.

32Bit Data Transfer

Disabled,

Auto Auto,

0, 1, 2, 3, 4

Auto,

SWDMA0, SWDMA1, SWDMA2, MWDMA0, MWDMA1, MWDMA2, UDMA0, UDMA1, UDMA2, UDMA3, UDMA4, UDMA5

Auto,

Disabled, Enabled

Disabled,

Enabled

Select the type of device connected to the system.

Enabling LBA causes Logical Block Addressing to be used in place of Cylinders, Heads, and Sectors. Select if the device should run in Block mode.

Selects the method for transferring the data between the hard disk and system memory. The Setup menu only lists those options supported by the drive and platform.

Selects the Ultra DMA mode used for moving data to/from the drive. Autotype the drive to select the optimum transfer mode.

Note: To use UDMA Mode 2, 3, 4 and 5 with a device, the harddisk cable used MUST be UDMA66 cable (80 conductor cable).

Select if the Device should be monitoring itself (SelfMonitoring, Analysis and Reporting Technology System). Select if the Device should be using 32Bit data Transfer.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 52 of 71

7.3.3 Advanced settings – Floppy Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Floppy Configuration

Floppy A [Disabled]

Floppy B [Disabled]

Feature Options Description

Floppy A

Floppy B

Disabled,

360KB,

1.2MB, 720KB,

1.44MB,

2.88MB

Disabled,

360KB,

1.2MB, 720KB,

1.44MB,

2.88MB

Select Floppy device installed in the system.

Select the type of floppy drive connected to the system

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 53 of 71

7.3.4 Advanced settings – SuperIO Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Configure Win627THF Super IO Chipset

OnBoard Floppy Controller [Disabled]

Floppy Drive Swap [Disabled] Serial Port1 Address [3F8/IRQ4] Serial Port2 Address [2F8/IRQ3] Serial Port2 Mode [Normal] Parallel Port Mode [Disabled] OnBoard Game Port [Disabled]

Feature Options Description

OnBoard Floppy Controller

Serial Port1 Address Disabled,

Serial Port2 Address Disabled,

Serial Port2 Mode

Parallel Port Address

Parallel Port Mode Normal,

EPP Version 1.9, 1.7 Setup the required version of EPP. ECP Mode DMA Channel DMA0,

Parallel Port IRQ IRQ5,

OnBoard Game Port

Disabled,

Enabled

3F8/IRQ4,

2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,

3F8/IRQ4,

2F8/IRQ3,

3E8/IRQ4, 2E8/IRQ3,

Normal,

IRDA, ASK IR

Disabled,

378, 278, 3BC

Bi-Directional, EPP, ECP

DMA1, DMA3

IRQ7

Disabled, Enabled

Enable or disable the Floppy Controller.

Select the BASE I/O addresse and IRQ.

Select Mode for Serial Port2.

Select the I/O address for the LPT.

Select the requested operation mode.

Select a DMA channel.

Select the IRQ for the parallel port.

Enable/ Disable Game Port.

Allows BIOS to Enable or Disable Floppy Controller.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 54 of 71

7.3.5 Advanced settings – Hardw are Health Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Hardware Health Event Monitoring

H/W Health Function [Enabled]

Chassis Intrusion [Disabled]

System Temperature :37ºC/98ºF CPU Temperature :43ºC/109ºF

Fan3 Speed :2657 RPM Fan2 Speed :2657 RPM Fan1 Speed :2657 RPM

VcoreA :1.483 V VcoreB :1.596 V +3.3Vin :3.435 V +5Vin :5.134 V +12Vin :12.016 V

-12Vin :-11.787 V

-5Vin :-5.200 V

Feature Options Description

H/W Health Function

Chassis Intrusion

Enable,

Disabled

Enable, Disabled

Enable Hardware Health Monitoring Device .

Enable BIOS warning in case intrusion is detected on Case Open (S1).

Enable Hardware Health Monitoring Device.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 55 of 71

7.3.6 Advanced settings – ACPI Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

ACPI Aware O/S [Yes]

>

General ACPI Configuration

>

Advanced ACPI Configuration

Feature Options Description

ACPI Aware O/S No,

Yes

Select if O/S supports ACPI.

Enable / disable ACPI support for Operating System

ENABLE: IF OS supports ACPI.

DISABLE: IF OS does not support ACPI.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 56 of 71

7.3.7 Advanced settings – General ACPI Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

General ACPI Configuration

Suspend mode [S1 & S3 (STR)] Repost Video on S3 Resume [No]

Feature Options Description

Suspend mode S1 (POS) only,

S1&S3 (STR)

Repost Video on S3 Resume

No,

Yes

Select the ACPI state used for System Suspend.

Determines whether to invoke VGA BIOS post on S3/STR resume.

Select the ACPI state used for System Suspend.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 57 of 71

7.3.8 Advanced settings – Advanced ACPI Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Advanced ACPI Configuration

ACPI 2.0 Features [No] ACPI APIC support [Enabled] AMI OEMB table [Enabled] Headless mode [Disabled]

Feature Options Description

ACPI 2.0 Features

ACPI APIC support

AMI OEMB table

Headless mode Enabled,

No,

Yes

Enabled,

Disabled

Enabled,

Disabled

Enable/ Disable ACPI 2.0 features.

Setup if the APIC controller should be supported in the ACPI code. Enable/ Disable AMI OEMB table.

Enable/ Disable Headless mode.

Enable RSDP pointers to 64-bit Fixed System Description Tables.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 58 of 71

7.3.9 Advanced settings – USB Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

USB Configuration

Module Version – 2.23.2-6.4

USB Devices Enabled : 1 Drive

Legacy USB Support [Enabled] USB 2.0 Controller Mode [FullSpeed]

>

USB Mass Storage Device Configuration

Feature Options Description

Legacy USB Support Disabled,

Enabled,

Auto

USB 2.0 Controller Mode

FullSpeed,

HiSpeed

Support for legacy USB Keyboard.

Configures the USB 2.0 controller in HiSpeed (480Mbps) or FullSpeed (12Mbps).

Enables support for Legacy USB. AUTO Option disables Legacy support if No USB devices are connected.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 59 of 71

7.3.10 Advanced settings – USB Mass Storage Device Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

USB Mass Storage Device Configuration

USB Mass Storage Reset Delay [20 Sec]

Device #1 JetFlash TS256MJF2L Emulation Type [Auto]

Feature Options Description

USB Mass Storage Reset Delay Emulation Type

10 Sec, 20 Sec, 30

Sec, 40 Sec

Auto,

Floppy, Forced FDD, Hard Disk, CDROM

Number of seconds the BIOS waits for the USB device after start unit command. Setup the emulation type for the USB device.

Enables USB host controllers.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 60 of 71

7.4 PCIPnP Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Advanced PCI/PnP Settings

Warning: Setting wrong values in below sections

May cause system to malfunction.

Plug & Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] PCI IDE BusMaster [Enabled] Spread Spectrum Mode [Disabled] TPM Clock [Enabled]

PCI Slot-1 IRQ Preference [Auto] PCI Slot-2 IRQ Preference [Auto] PCI Slot-6 IRQ Preference [Auto]

Feature Options Description

Plug & Play O/S

PCI Latency Timer

Allocate IRQ to PCI VGA

Palette Snooping

PCI IDE BusMaster

Spread Spectrum Mode

PCI Slot-1 IRQ Preference

PCI Slot-2 IRQ Preference

PCI Slot-6 IRQ Preference

Note: PCI Slot-3 IRQ Preference, PCI Slot-4 IRQ Preference and PCI Slot-5 IRQ Preference do not exist.

No,

Yes

32, 64, 96, 128,

160, 192, 224, 248

Yes,

No

Disabled, Enabled

Enabled,

Disabled

Enabled,

Disabled

Auto, 3, 4, 5, 7, 9,

10, 11, 12, 14, 15

Auto, 3, 4, 5, 7, 9,

10, 11, 12, 14, 15

Auto, 3, 4, 5, 7, 9,

10, 11, 12, 14, 15

Select if you have a PnP O/S.

Value in units of PCI clocks for PCI device latency timer register. Assigns IRQ to PCI VGA card.

ENABLED: informs the PCI device that an ISA graphics device is installed in the system so the card will function correctly. Setup PCI bus mastering for read/write to IDE drives.

Spread Spectrum Mode.

Manual IRQ selection.

Manual IRQ selection. Only available on the 886LCD/ATX(GV)

NO: lets the BIOS configure all the devices in the system. YES: lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system.

<- Select Screen || Select Item +- change option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 61 of 71

7.5 Boot Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Boot Settings

>

Boot Settings Configuration

st

Boot Device [PM-ST3120022A]

1

nd

Boot Device [1st FLOPPY DRIVE]

2

rd

Boot Device [CORSAIR Flash Voya]

3

th

Boot Device [Realtek Boot Agent]

4

Configure Settings during System Boot.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 62 of 71

7.5.1 Boot – Boot Settings Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Boot Settings

Quick Boot [Enabled] Quiet Boot [Disabled] AddOn ROM Display Mode [force BIOS] Bootup Num-Lock [On] PS/2 Mouse Support [Auto] Wait for `F1´ If Error [Enabled] Hit ‘DEL’ Message Display [Enabled] Interrupt 19 Capture [Disabled]

Feature Options Description

Quick Boot

Quiet Boot

AddOn ROM Display Mode

Bootup Num-Lock Off,

PS/2 Mouse Support Disabled,

Wait For ´F1´If Error

Hit ‘DEL’ Message Display Disabled,

Interrupt 19 Capture

Note 1: Errors: <INS> Pressed, Timer Error, Interrupt Controller-1 error, Keyboard/Interface Error, Primary Master Hard Disk Error, S.M.A.R.T HDD Error, Cache Memory Error, DMA Controller Error, Resource Conflict, PCI I/O conflict, PCI ROM conflict, PCI IRQ conflict, PCI IRQ routing table error, Halt on Invalid Time/Date, NVRAM Bad, Static Resource Conflict, PCI I/O conflict and PCI ROM conflict.

Enabled,

Disabled

Disabled,

Enabled, Enabled & Maintain

Force BIOS,

Keep Current

On

Enabled,

Auto Enabled,

Disabled

Enabled Disabled,

Enabled

Allows BIOS to skip certain test while booting.

Shows boot logo instead of POST screen.

Set display mode for Option ROM.

Select Power-on state for numlock.

Select support for PS/2 Mouse.

Wait for F1 key to be pressed if error occurs. (See note 1 below) Display the message or not.

Allows option ROMs to trap interrupt 19.

Configure Settings during System Boot.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 63 of 71

7.6 Security Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Security Settings

Supervisor Password :Installed User Password :Installed

Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup]

Boot Sector Virus Protection [Disabled]

Hard Disk Security

Primary Master HDD User Password Primary Slave HDD User Password Secondary Slave HDD User Password

Feature Options Description

Change Supervisor Password User Access Level No Access,

Change User Password Password Change the User Password. Clear User Password Ok,

Password Check Setup,

Boot Sector Virus Protection HDD Password Password Locks the HDD with a password, the user needs to

Password Change the Supervisor Password.

Set the user level Access for the BIOS. View Only, Limited, Full Access

Clears the User Password. Cancel

Shall the BIOS prompt for password on boot or only Always Enabled,

Disabled

when entering setup.

Will write protect the MBR when the BIOS is used to

access the harddrive.

type the password on power on.

Install or Change the password.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 64 of 71

7.7 Chipset Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Advanced Chipset Settings

Warning: Setting wrong values in below sections may cause system to malfunction.

>

Intel Brookdale-G NorthBridge Configuration

>

Intel ICH4 SouthBridge Configuration

Intel Brookdale-G NorthBridge chipset configuration options.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 65 of 71

7.7.1 Advanced Chipset Settings – Intel Brookdale-G NorthBridge Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Configure advanced settings for NorthBrigde

Primary Video Device [Auto] Graphics Mode Select [Enabled, 8MB] Graphics Aperture Size [64MB] IGD – Device 2,Function 1: [Enabled] Boot Type: [VBIOS Default] DVO: [N/A]

Feature Options Description

Primary Video Device Internal,

External PCI,

Auto

Graphics Mode Select Disabled, 1MB,

8MB

Graphics Aperture Size 4MB, 8MB, 16Mb,

32MB, 64MB,

128MB, 256MB

IGD – Device 2, Function 1 Disabled,

Enabled

Boot Type

DVO [N/A]

VBIOS Default,

CRT, LFP, CRT+LFP, EFP, TV, CRT+EFP, CRT+TV, EFP+EFP2, EFP+TV

Select which graphics controller to use as the primary

boot device.

Select the amount of system memory used by the

internal graphics device.

Size of the AGP Aperture memory.

Setup the multimonitor function.

Setup type of boot screen.

Select which graphics controller to use as the primary boot device.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 66 of 71

7.7.2 Advanced Chipset Settings – SouthBridge Configuration

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Onboard IDE [Enabled] SMBUS [Enabled] AC´97 Audio [Enabled] USB #1 [Enabled] USB #2 [Enabled] USB #3 [Enabled] EHCI (USB 2.0) [Enabled]

Onboard LAN [Enabled] Onboard SATA [Enabled] IOAPIC [Enabled] Extended IOAPIC [Enabled]

Feature Options Description

Onboard IDE

SMBUS

AC´97 Audio

USB #1

USB #2

USB #3

EHCI (USB 2.0)

Onboard LAN Disable

Onboard Sata

IOAPIC

Extended IOAPIC

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enabled

With RPL/PXE boot

Enabled

Disable

Enabled

Disable

Enabled

Disable

Enable / Disable ICH4 IDE Controller function.

Enable / Disable ICH4 SMBUS function.

Enable / Disable ICH4 AC97 Audio Controller function.

Enable / Disable ICH4 USB Host Controller#1 function.

Enable / Disable ICH4 USB Host Controller#2 function.

Enable / Disable ICH4 USB Host Controller#3 function.

Enable / Disable ICH4 EHCI USB Controller function.

Set up Onboard LAN for Disable, Enable or Enable

with RPL/PXE boot.

Enable / Disable Onboard SATA.

Enable / Disable the ICH4 IOAPIC function.

Enable / Disable the extended mode of ICH4 IOAPIC

function.

Enable / Disable the ICH4 IOAPIC function.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 67 of 71

7.8 Power Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

APM Configuration

Power Management/APM [Enabled] Power Button Mode [On/Off] Restore on AC Power Loss [Last state] Force Throttle [Disabled] Manual Throttle Ratio [50%] Wake on LAN Resume S5 [Disabled]

Keyboard PowerOn [Disabled] Mouse PowerOn [Disabled]

Feature Options Description

Power Management/APM Disabled,

Enabled

Power Button Mode

Restore on AC Power Loss Power Off,

Force Throttle

Manual Throttle Ratio 87.5%, 75.0%,

Wake on LAN Resume S5

Keyboard PowerOn

Mouse PowerOn

On/Off,

Standby, Suspend

Power On,

Last State Disabled,

Enabled

62.5%, 50%,

37.5%, 25%, 12.5%

Disabled,

Enabled

Disabled,

Space Key

Disabled,

Double Left Button, Double Right Button

Setup the SMI/APM support.

Go Into On/Off, Standby or Suspend when Power

button is pressed.

Disable/Enable the force to thermal throtting function.

Select the Duty Cycle in Throttle mode.

Disabled,Enabled generate of SMI on SLP_EN sp we

can wake from S5.

Enable/Disable SMI based power management and APM support.

<- Select Screen || Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 68 of 71

7.9 Exit Menu

BIOS Setup Utility

Main Advanced PCIPnP Boot Security Chipset Power Exit

Exit Options

Save Changes and Exit Discard Changes and Exit Discard Changes

Load Optimal Defaults Load Failsafe Defaults

Secure CMOS [Disable] Halt on invalid Time/Date [Enabled]

Feature Options Description

Save Changes and Exit Ok,

Cancel

Discard Changes and Exit Ok,

Cancel

Discard Changes Ok,

Cancel

Load Optimal Defaults Ok,

Cancel

Load Failsafe Defaults Ok,

Cancel

Secure CMOS

Halt on Invalid Time/Date Disable,

Disable,

Enabled

Exit system setup after saving the changes

Exit system setup without saving any changes

Discards changes done so far to any of the setup

questions

Load Optimal Default values for all the setup questions

Load Failsafe Default values for all the setup questions

Enabled will store current CMOS in non volatile ram.

This will maintain the settings even if battery is failing.

Exit system setup after saving the changes.

F10 Key can be used for this operation.

<- Select Screen || Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 69 of 71

7.10 AMI BIOS Beep Codes

Boot Block Beep Codes:

Number of

Beeps

1 Insert diskette in floppy drive A: 2 ‘AMIBOOT.ROM’ file not found in root directory of diskette in A: 3 Base Memory error 4 Flash Programming successful 5 Floppy read error 6 Keyboard controller BAT command failed 7 No Flash EPROM detected 8 Floppy controller failure

9 Boot Block BIOS checksum error 10 Flash Erase error 11 Flash Program error 12 ‘AMIBOOT.ROM’ file size error 13 BIOS ROM image mismatch (file layout does not match image present in flash

POST BIOS Beep Codes:

Number of

Beeps

1 Memory refresh timer error.

2 Parity error in base memory (first 64KB block)

3 Base memory read/write test error

4 Motherboard timer not operational

5 Processor error

6 8042 Gate A20 test error (cannot switch to protected mode)

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

9 AMIBIOS ROM checksum error 10 CMOS shutdown register read/write error 11 Cache memory test failed

Troubleshooting POST BIOS Beep Codes:

Number of

Beeps

1, 2 or 3 Reseat the memory, or replace with known good modules.

4-7, 9-11 Fatal error indicating a serious problem with the system. Consult your system

8 If the system video adapter is an add-in card, replace or reseat the video adapter.

Description

device)

Description

Troubleshooting Action

manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter.

• If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support.

• If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card.

If the video adapter is an integrated part of the system board, the board may be faulty.

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 70 of 71

8. OS setup

Use the Setup.exe files for all relevant drivers. The drivers can be found on the 886LCD/ATXU(GV) and 886LCD/ATX(GV) Driver CD or they can be downloaded from the homepage http://www.kontron-emea.com

886LCD/ATX(GV) -/ATXU(GV)

KTD-00647-F Public User Manual Date: 2009-05-18 Page 71 of 71

9. Warranty

KONTRON Technology warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a similar product. Replacement Product or parts may include remanufactured or refurbished parts or components.

The warranty does not cover:

1. Damage, deterioration or malfunction resulting from: A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product

modification, or failure to follow instructions supplied with the product. B. Repair or attempted repair by anyone not authorized by KONTRON Technology. C. Causes external to the product, such as electric power fluctuations or failure. D. Normal wear and tear. E. Any other causes which does not relate to a product defect.

2. Removal, installation, and set-up service charges.

Exclusion of damages:

KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR:

1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.

2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.