Kompernass KH 3217 User Manual
Safety Magnet Lock Set
Package contents
q
4 installation templates
w
4 locks with magnet connectors
e
1 magnet key
r
4 lock plates
t
4 unlocking bars
y
4 extension inserts
u
1 drilling depth limiter
i
24 screws (12 mm)
o 4 T-inserts
a 4 marking stickers
Required installation tools
Phillips head screwdriver
Drill
7 mm drill bit
Sharp object for making marks
(such as a nail)
Proper use
The safety magnet lock is intended for
locking drawers and doors of small
furniture (min. door thickness 12,7 mm).
It is not for securing house doors or
other heavy doors. It is not intended
for use in commercial or industrial
areas
Safety instructions
Do not store the magnetic parts of
the magnet lock near credit cards,
video cassettes or audio cassettes.
This leads to irreparable damaging
of the magnetic strips and tape!
This magnet lock cannot guarantee
100% safety. Never leave your
children unsupervised for long!
Observe whether your children are
capable of opening the magnet
lock.
Assembly
Note: Do not drill through the letters
in the installation template
q
, always
drill through the marking (X). Please
note that when installing the safety
magnet lock in drawers, a free space
of 4 x 6 cm is required.
For surface-mounted doors / drawers
1a. Remove the narrow sticker
from the installation template
q
and stick it onto an appropriate
place on the cabinet inside wall
(see Fig. 1). When installing the
lock in drawers, place the installation template
q
on the upper inside drawer wall at the height of the
grip or knob.
1b. Fold the installation template
q
around the corner at the fold line
and mark the two screw holes
(X) for the lock plate rwith a
sharp object (such as a nail). Pull
off the back of the sticker
.
2. Press the door or drawer hard
against the sticker
. When the
door / drawer is opened, the installation template
q
will have been
transferred to the correct location
for further installation.
3. Smooth out the installation template
q
and mark four of the six
screw holes
(X) (two above and
two below) for the lock
w
(see Fig. 2).
Continue with Step 4.
For inset doors / drawers
1a. Measure the door thickness
(depth) / thickness of the drawer
front.
Draw the new markings for the
screw holes of the lock plate
r
onto the installation template q:
To do this, move the markings
along the dotted arrow line by the
measured door thickness, starting
from the screw holes
(X)
Make
certain that the new markings are
situated parallel to the
screw holes
(X).
Remove the narrow sticker
from the installation template
q
and stick it with the fold line
onto an appropriate place on the
cabinet inside wall (see Fig. 1).
When installing the lock in drawers, place the installation template
q
on the upper inside drawer
wall at the height of the grip or
knob.
1b. Mark the two new
screw holes for
the lock plate
r
with a sharp object
(such as a nail). While closing the
door, mark the position of the installation template
q
on the narrow
part of the inside of the door using a
pencil. Carefully remove the installation template
q
from the inside ca-
binet wall.
2.
Pull off the back of the sticker .
Stick the installation template
q
onto the previously marked position,
flush against the inside edge of the
door using the sticker
(see Fig. 2).
3. Smooth out the installation template
q
and mark four of the six
screw holes
(X) (two above and
two below) for the lock
w
.
Fig. 1
q
w
e
r
t
y
u
i
o
a
Fig. 2
D
4. Slide the drilling depth limiter
u
onto the 7 mm drill bit based on
the door thickness so that the drilled
hole will reach to 3 mm from the
front of the door / drawer (Fig. 3).
Check the drilling depth on the outer edge of the door.
5.
Set the drill against the inside of the
door / drawer on the marking
(X)
7 mm on the installation template
q
(see Fig. 3) and drill the hole until the
drilling depth limiter
u
rests against
the inside of the door /
.
Do not drill through the door /
drawer! The drilling depth limiter
u
must not be allowed to slide while
drilling!
6. Remove the drilling dust from the
hole. Check whether the magnet
connector of the lock wfits
perfectly into the hole with the
T-insert
o
(see Fig. 4). For thinner
doors, leave out the T-insert
o
.
7.
Screw the lock plate rinto the cabinet
inside wall at the previously marked location using the enclosed screws
i
(Fig. 5). For drawer installation, it is recommended to take the drawer out of
the cabinet first. This offers you more
space to work.
8. Screw the lock wonto the inside of
the door / drawer at the marked location (see Fig. 5) (for thick doors /
drawers, use the T-insert
o
and if
necessary the extension insert
y
(Fig. 4)). Check the function of the
lock from the outside of the door.
Close the door and check the lock.
If necessary, correct the position of
the lock plate
r
by slightly loosening
the screws and sliding the lock plate
r
using the long holes.
For double doors without a middle
board
Mount the magnet lock on the top or
bottom of the cabinet.
Tip:
Place a marking sticker
a
on the outside of the door to find the correct
place to use the magnet key
e
more
quickly. Always place the maget key
e
at an agreed location near the secured door / drawer. Do not keep the
mag-net key
e
in a clothing pocket
and never inside the cabinet being
secured.
Unlocking bar
If you do not wish to use the lock, you
can permanently unlock the lock with
the unlocking bar
t
.
Press the unlocking bar
t
over the
lock
w
so that the pins snap into the
holes first on one side, then on the
other side. The writing "UNLOCK"
must face forward.
Press the lock latch closed and turn
the unlocking bar
t
forward until
reaching the stop (see Fig. 6).
To lock the door, make certain that
the unlocking bar
t
is turned back
(see Fig. 7).
Disposal
Do not throw the magnet lock into
normal household waste.
Dispose of the magnet lock through
an approved waste disposal company
or your community disposal facility.
Observe the currently applicable regulations. In case of doubt, please
contact your waste disposal centre.
Warranty and service
This product comes with a 3-year
warranty as of the date of purchase.
Please keep your receipt as proof of
purchase.
Please contact your local service centre
regarding warranty issues.
Kompernas Service Ireland
c/o Irish Connection
41 Harbour view
Howth Co. Dublin
Tel.: 087 9962077
Fax.: 18398056
e-mail: support.ie@kompernass.com
28.6 mm - 39.7 mm
15.9 mm - 28.6 mm
12.7 mm - 15.9 mm
Fig. 4
Fig. 3
Fig. 5
Kompernaß GmbH
Burgstraße 21
D-44867 Bochum
www.kompernass.com
ID. No.: KH3217-10/05-V9
Fig. 7
Fig. 6
Loading...