Read the operating instructions carefully
before using the appliance for the first
time and preserve this booklet for later
reference. Also, give these operating instructions to whoever might acquire the
appliance at a future time.
Safety instructions
Risk of personal injury!
• Keep and store the appliance out of
the reach of children.
This laser appliance contains a Class 2 Laser.
NEVER direct the laser beam at people or
animals. NEVER look directly into the laser.
The laser beam can cause serious eye
damage.
• Do NOT direct the laser beam at strongly
reflective material. Reflected laser beams
are also dangerous.
• In the event of the batteries leaking
acids, wear protective gloves. There is
a risk of receiving chemical burns!
Beware of appliance damage!
• NEVER subject the appliance to rain.
Do not use the appliance in wet or
moist environments.
• Do not use the appliance at locations
where there is a danger of fire or explosion, e.g. in the vicinity of inflammable
liquids or gases.
• All adjustments intended to increase
the laser power are forbidden.
• To avoid damage to the appliance,
arrange for repairs to be carried out
only by our Customer Services Department or qualified specialists.
• Regularly check the condition of the
batteries. Leaking batteries can cause
damage to the laser appliance.
• If you do not intend to use the laser
appliance for an extended period,
remove the batteries.
• Always change all batteries at the same
time and always use batteries of the
same type.
• Clean the battery compartment with
a dry cloth.
• No liabilty will be accepted for damage
resulting from manipulation to the laser
equipment as well as from disregarding
these safety instructions.
Intended use
The appliance is intended for use in making
alignments and determining angles in
domestic construction work.
The appliance is intended for domestic
purposes only, not for commercial purposes.
Items supplied
• Laser appliance with rotating plate
• 2 Batteries 1.5 V,
Type AAA/LR03
• Operating instructions
• Warranty card
Technical Data
Power supply:
2 Batteries 1.5 V, Type AAA/LR03
Measurement accuracy:
± 6,35 mm over 5 meters
Laser class 2
(≤5mW, λ= 650 nm)
- 1 -
Appliance description
Laser appliance
q
ON/OFF button
w
Spirit level for horizontal lines
e
Spirit level for vertical lines
r
Laser lens
t
Rotating plate with degree scale
y
Marking arrow
u
Fastening pins
i
Fixing points on the laser appliance
o
Fixing points on the rotating plate
a
Battery compartment
s
(on the rear side)
Inserting the batteries
1. Open the battery compartment s.
2. Insert two batteries of Type AAA/LR03
into the battery compartment
with the polarity markings in the battery
compartment
3. Close the battery compartment
s
.
. Comply
s
s
.
Utilisation
Switching On and Off
1. To switch the laser appliance qon,
press the ON/OFF
2. To switch the laser appliance
press the ON/OFF
again.
Utilisation on a wall
1. Remove the laser appliance qfrom
the rotating plate. The laser appliance
clings to the rotating plate
cally.
2. Place the rotating plate
tion on the wall from where you wish
to draw the alignment line.
button.
w
button once
w
y
off,
q
magneti-
y
at the posi-
3. Secure the rotating plate
in that you take both fastening pins
from the sides of the appliance and you
press them through the fixing points on
the rotating plate
(See Fig.
Notice:
The fastening pins ican be inserted
into most upper surfaces, such as wood,
plaster or mortar. Alternatively, especially with other upper surfaces, you
could also use adhesive tape for securing the rotating plate
You can also secure the laser appliance
q
the fastening pins
through fixing points on the laser
appliance
4. Place the laser appliance
rotating plate
5. Turn the laser appliance
marking arrow
direction.
6. Switch the laser appliance
pressing the ON/OFF button
The laser beam appears on the wall in the
direction of the marking arrow
without the rotating plate, in that
).
o
a
itself.
.
y
into the desired
u
to the wall
y
and into the wall
.
y
are inserted
i
onto the
q
with the
q
on, by
q
.
w
.
u
i
Plumb-line
To mark a plumb-line, turn the laser
appliance
with the marking arrow upointing in
the direction in which the laser marking
is to be indicated, then finely adjust it
vertically with the spirit level
on the rotating plate
q
r
y
.
- 2 -
Horizontal line
To mark a horizontal line, turn the laser
appliance
with the marking arrow upointing in
the direction in which the laser marking
is to be indicated, then finely adjust it
horizontally with the spirit level
Important:
The air-bubbles in the spirit levels
must be positioned between the two
markings.
on the rotating plate
q
.
e
e+r
Storage
• Keep the fastening pins iin the recesses
y
provided on the sides of the appliance.
• If you are not going to use the appliance
for a long period, remove the batteries
from the battery compartment
store them seperately.
Disposal
s
and
Angles
1. To mark an angle, shift the zero marking
of the degree scale to the marking arrow
on the laser appliance q (Fig. ).
u
2. Turn the laser appliance qfrom the
start position (Fig. ) with the marking
arrow uto the desired angle (e.g. 45°,
Fig. ).
Utilisation on the floor/on the ceiling
1. Should you use the laser appliance
on the floor or on the ceiling, secure
it as described above if need be.
2. Turn the laser appliance
marking arrow
in the desired direction.
u
q
q
with the
Cleaning and Care
CAUTION!
Under no circumstances should the
laser appliance
water or other fluids. The appliance
could be irreparably damaged.
be submersed in
q
Do not dispose of the appliance in
your normal domestic waste.
Dispose of the appliance through an
approved disposal centre or at your
community waste facility.
Observe the currently applicable regulations. In case of doubt, please contact
your waste disposal centre.
Disposal of batteries!
Do not dispose of batteries with household
waste. All consumers are legally obliged
to dispose of batteries at a collection site
in their community/city district or at a
retail store.
This obligation is intended to ensure that
batteries are disposed of in an environmentally safe fashion. Only dispose of
batteries when they are fully discharged.
Dispose of the packaging materials
in an environmentally responsible
manner.
Do not use aggressive detergents or solvents.
They could cause damage to the appliance.
• Clean all components of the appliance
with a soft cloth.
• Clean the laser optic
brush.
with a soft
r
Warranty and Service
The warranty conditions and the service
address can be found on the supplied
warranty card.