Page 1
UK
KOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUM
www.kompernass.com
ID Nr.: KH1191-07/07-V2
IB_KH1191_EN.qxd 21.08.2007 17:00 Uhr Seite 1
Page 2
Electrical Biscuit Shaper KH 1191
Operating Instructions
IB_KH1191_EN.qxd 21.08.2007 17:00 Uhr Seite 2
Page 3
IB_KH1191_EN.qxd 21.08.2007 17:00 Uhr Seite 3
Page 4
qw
r
t
y
u
i
o
a
s
d
e
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 4
Page 5
- 3 -
KH1191
Index Page
Safety instructions 4
Intended usage 4
Package contents 4
Technical data 5
Appliance description 5
Before the first use 5
Assembling the Biscuit Shaper 5
Filling the container 6
Shaping biscuits 7
Adding decorations 7
Refilling with pastry or decorative mixture 7
Disassembly of the Biscuit Shaper 8
Tips 8
Cleaning and care 9
Disposal 9
Warranty & service 9
Importer 9
Recipes 10
Read these operating instructions carefully before using the appliance for the first
time and preserve this booklet for later reference. Pass the booklet on to whoever
might acquire the appliance at a later date.
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 3
Page 6
- 4 -
Electrical Biscuit Shaper
KH 1191
Safety instructions
To avoid potentially fatal electric shocks:
• The voltage of the power source must
match the details given on the plate
affixed to the appliance.
• Arrange for defective power plugs
and/or cables to be replaced at once
by qualified technicians or our
Customer Service Department.
• Do not expose the appliance to rain
and never use it in a humid or wet
environment. Ensure that the cable
never gets damp or wet while the
appliance is in use.
To avoid the risks of fire or injuries:
• If they have not previously been
supervised or instructed in its correct
usage, do not allow individuals (including children) to use the appliance
whose physical, sensorial or mental
abilities or lack of experience and
knowledge hinder their safe usage
of it.
• Inform children about the appliance
and its potential dangers so that they
do not play with it.
• Ensure that the power plug is quickly
accessible in cases of danger, and that
there is no danger of tripping over
the cable.
Tips for safety:
• In cases of danger, immediately remove
the electrical plug from the socket.
• Never use the appliance for purposes
other than those for which it was designed.
• Do not use the appliance outdoors.
• Always be attentive! Always pay attention to what you are doing and act
with common sense. Never use the
appliance when you are distracted or
don’t feel well.
• Ensure that the appliance is correctly
and completely assembled before
taking it into use.
• Remove the plug from the socket if
the appliance is not being used, when
removing components and for cleaning.
Intended usage
The Biscuit Shaper KH 1191 is intended
for the shaping of biscuits and for decorating cakes etc. It is intended exclusively
for private, not commercial, applications.
Package contents
Electrical Biscuit Shaper KH 1191
12 Motif discs
8 Nozzles
Operating instructions
Warranty card
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 4
Page 7
- 5 -
Assembling the Biscuit Shaper
L Note: Remove the power plug
from the wall socket before assembling accessories.
Inserting the threaded rod with pusher
1. Place the end of the threaded rod
in the motor unit . Ensure that the
pins inside the motor unit engage
with the guide rails on the threaded
rod .
2. Slide the threaded rod with the
pusher as far as it will go into the
motor unit .
Assembling the container
L Note: The container must be fit-
ted, otherwise the Biscuit Shaper
will not function!
1. Slide the container over the pusher
such that the guide rails inside the
container engage in the in notches
on the pusher .
2. Place the container on the motor
unit so that the arrow on the container points to the open lock
on the motor unit .
3. Turn the container until the arrow
on the container points to the
closed lock on the motor unit .
4. Insert the power plug into a wall
socket.
5. Place the direction switch onto the
arrow pointing downwards Ð.
6. Press and hold the start button
until the pusher has returned itself
to the MAX marking.
7. Remove the power plug from the
wall socket.
Technical data
Mains voltage: 220 - 240 V / 50Hz
Power rating: 12 W
Continuous
operating time: 1 Minute
Protection class: II
Appliance description
Direction switch
Start switch
Power cable with power plug
Motor unit
Threaded rod
Pusher
Container
Nozzle adapter with seal
Nozzles
쐅 Adapter lock
쐈 Lock ring
쐉 Motif discs
Before the first use
Take the Biscuit Shaper and all accessories
from the packaging and remove all
packaging material.
Clean all of the components as described in
the section „Cleaning and care“.
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 5
Page 8
- 6 -
Assembling motif discs
When the pusher and container
are assembled:
1. Select the desire motif disc 쐉.
2. Place the motif disc 쐉 into the lock
ring 쐈.
3. Place the lock ring 쐈 with the motif
disc 쐉 onto the container .
4. Turn the lock ring 쐈 in the direction
of the arrow until it engages .
Assembling the nozzles
When the pusher and container
are assembled:
1. Place the nozzle adaptor into the
lock ring 쐈. The thread must point
outwards.
2. Place the lock ring 쐈 with the nozzle
adaptor onto the container.
3. Turn the lock ring 쐈 in the direction
of the arrow until it engages .
4. Select a nozzle .
5. Place the nozzle on the nozzle
adapter .
6. Screw the adapter lock 쐅 over the
nozzle on the nozzle adapter .
7. Adjust the lock device on the nozzle
adaptor to "CLOSE".
Filling the container
L The pastry to be processed must be
at room temperature. If it is too soft,
place it in the refrigerator for a
short time.
1. Turn the container so that the
arrow points to the open lock .
2. Remove the container from the
motor unit . Leave the threaded rod
with the pusher in the motor
unit .
L Tip: If need be, moisten the inner
surface of the container with
water before filling it with pastry.
Doing so helps avoid having the
pastry stick to the inner surfaces of
the container .
3. Shape the pastry / decorating mixture
to a roll. This permits easier filling. Fill
the container with this pastry roll.
L Note: Fill the container at the
most to the MAX marking. Process
the pastry straight away.
4. Place the container onto the motor
unit as described in the chapter
"Assembling the container".
5. Insert the power plug into a wall
socket.
The Biscuit Shaper is now ready for use.
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 6
Page 9
- 7 -
Shaping biscuits
L Tips:
• Use exclusively the motif discs 쐉 for
shaping the biscuits.
• Line the baking tray with baking paper.
Do not use Teflon, fats or oil paper, as
the biscuits then do not keep their
shape.
• Ensure that the lock ring 쐈 sits firmly
on the container and that the container is correctly mounted on the
motor unit before you switch the
appliance on.
1. Place the direction switch onto the
arrow pointing upwards Ï.
2. Direct the biscuit shaper over the
baking tray.
3. Press on the start switch until the
first biscuit has been formed.
4. Release the start switch and direct
the biscuit shaper at another position.
How long you must press the start
switch is dependant on the desired
size and shape of the biscuit. If you
press the start switch only shortly,
you will form a small biscuit. The longer
you press the start switch , the larger
the biscuit will be.
5. Repeat the steps until you have shaped
a sufficient number of biscuits.
L Note: Should the pastry be too sticky,
place it in the refrigerator for 15
minutes.
Adding decorations
L Tips:
• Use the nozzles exclusively for
shaping fluid-like substances, such as
whipped cream.
• The decoration substance must have
a soft and creamy consistency, otherwise it will block the nozzle .
• Press the start switch only shortly
to start with, to see how the substance
responds. It can happen that the substance may continue to flow out for
a short time.
1. Place the direction switch onto the
arrow pointing upwards Ï.
2. Place the lock device on the nozzle
adaptor onto "OPEN".
3. Hold the Biscuit Shaper at a slight angle.
4. Press the start switch .
5. As soon as the decorative substance
starts to flow from the nozzle , move
the Biscuit Shaper in accord with the
decorative design you wish to create.
L Note: Should the pusher block
during use, it could be that the substance or the pastry is too firm.
Remove all of the substance resp.
the pastry and, if possible, blend
some fluids into it.
Refilling with pastry or decorative
mixture
1. Place the direction switch onto the
arrow pointing downwards Ð.
2. Press and hold the start button
until the pusher has returned itself
to the MAX marking.
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 7
Page 10
- 8 -
Danger!: Remove the plug from
the wall socket before refilling the
container.
L Note: Should the threaded rod not
retract, first remove the lock ring 쐈
and, whilst holding the start switch
pressed down, lightly push the
threaded rod to the rear.
3. Remove the lock ring 쐈.
L Note: If need be, dismantle the con-
tainer and remove the remaining
pastry. If necessary, also remove any
pastry that may have collected behind the pusher .
Danger!: The motor unit may NOT
be submerged in water. If necessary,
it can be wiped clean with a moist
cloth.
4. Clean the parts that may be covered
with pastry and dry them well. (see
chapter "Cleaning and care")
5. Fill the Biscuit Shaper with pastry or
the decorative substance, reassemble
the Biscuit Shaper as described and
continue.
Disassembly of the Biscuit Shaper
1. Place the direction switch onto the
arrow pointing upwards Ï.
2. Press and hold the start button until the threaded rod has completely
extended itself outwards.
Danger!: Remove the power plug
from the wall socket before disassembling the appliance.
3. Unscrew the lock ring 쐈.
4. Turn the container so that the ar-
row is directed at the open lock .
5. Loosen the container from the
motor unit . The threaded rod
with pusher can now also be
dismantled.
Tips
• If need be, remove residues from the
Biscuit Shaper with a knife, pastry
scraper or similar.
• The consistency of the pastry or the
decorative substance should be such
that it easily flows from the motif
discs 쐉 or nozzles and remains
affixed onto the baking paper or the
item being decorated.
• Should the appliance refuse to start,
it could be that the pastry or the decorative substance is too firm or that
the container is not correctly attached to the motor unit .
• If the pastry is too firm to be processed, knead in some egg yolk or mix
in some fluids.
• Biscuit pastry that has lain in the refrigerator can become too firm for
processing.
• Should the pastry to be processed be
too soft, lay it in the refrigerator for
approx. 15 minutes or knead in a little
more flour.
• If the biscuit pastry contains finely
ground constituents (e.g. nuts or
almonds), select a motif disc 쐉 with
larger openings.
• With some pastries and motif discs it
is better to work quickly, with others,
better to work slowly.
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 8
Page 11
- 9 -
• Simply use trial and error until you
can produce biscuits that match your
expectations.
• If you want to use various motif discs
and nozzles, first of all use all of the
currently filled pastry or decorative
substance. Change the motif discs and
nozzles when you refill the Biscuit
Shaper.
Cleaning and care
Danger!: Remove the plug from
the wall socket before cleaning the
appliance.
As it is difficult to remove dried-on pastry
remains, always clean the Biscuit Shaper
and the motif discs employed 쐉 directly
after use.
Danger!: The motor unit may
NOT be submerged in water. If necessary, this can be wiped clean with
a moist cloth.
Do not use sharp or abrasive objects for
cleaning. Do not use aggressive or chemical cleaning agents.
Dismantle the Biscuit Shaper completely.
Rinse all parts, except the motor unit ,
in a mild detergent.
L Note: Do not clean any parts in a
dishwasher! They are not suitable
for dishwashers. The material could
be irreparably damaged!
Disposal
Under no circumstances should
you dispose of this appliance
with your domestic waste.
Dispose of the appliance through an
approved disposal centre or at your community waste facility.
Observe the currently applicable regulations. In case of doubt, please contact
your waste disposal centre.
Dispose of the packaging materials
in an environmentally responsible
manner.
Warranty & service
The warranty conditions and the service
address can be found in the warranty
booklet.
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
www.kompernass.com
L Note: The manufacturer is constantly
working on the further development of all types and models.
Therefore please accept that changes are possible to the actual items
supplied (equipment, shape, technology).
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 9
Page 12
- 10 -
Recipes
You can process commercially available
ready-made pastry with the Biscuit
Shaper.
Biscuits 1
Ingredients:
150 g butter
100 g powdered sugar
1 Pkt vanilla sugar
1 egg white
200 g plain flour (Type 405)
1 pinch salt
• Whip the butter until foamy, blend
in the sugar, vanilla sugar and the unbeaten egg white, then stir the mixture
with a hand mixer for about 8 minutes.
• Blend in the flour, then fill the pastry
into the Biscuit Shaper.
• Cover a baking tray with baking paper.
Make small biscuits on the tray with
the Biscuit Shaper.
• Bake in a convection oven for 1215 minutes at 175-190 ˚C.
• The edges should be golden brown.
Allow the biscuits to cool on the
baking tray.
Tip: Melt some plain cooking chocolate
in a bain-marie. Spread a teaspoonful of
chocolate onto the cooled biscuits and
decorate them with a half of a walnut.
L Depending on the size of the biscuits,
the baking times can vary.
Biscuits 2
Ingredients:
125 g butter
125 g powdered sugar
1 Pkt vanilla sugar
1 egg
1 egg white
250 g plain flour (Type 405)
1 pinch salt
• Whip the butter, sugar, vanilla sugar,
salt, egg and egg white until foamy,
blend in the flour.
• Cover a baking tray with baking paper.
Make small biscuits on the tray with
the Biscuit Shaper.
• Bake in a convection oven for 1215 minutes at 175-190 ˚C.
• Dip the biscuits in molten cooking
chocolate.
Tip: For darker biscuits, substitute 30 gr
of cocoa for the vanilla sugar. Dispense
with the salt and add 1 dessertspoon of
water instead.
L Depending on the size of the biscuits,
the baking times can vary.
KH1191
IB_KH1191_EN.qxd 21.08.2007 17:01 Uhr Seite 10
Loading...