KoldFront KIM450S User Manual
Built-in Ice Maker
KIM450S
Owner’s Manual
For more information on other great KoldFront products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the KoldFront ice maker and/or injury to the user. This ice maker is
designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may
invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other
technical data related to this unit. The unit must be used in a properly grounded wall outlet. Please read and follow the
safety information listed below to reduce the risk of fire, electric shock or injury. Installation should only be done by a
licensed plumber.
Electrical Safety
Do not exceed the power outlet ratings.
It is recommended the ice maker be connected on
its own circuit.
The unit must be installed in accordance with
state and local electrical, water and drain codes.
A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
Use outlets that cannot be turned off by a switch
or pull chain.
Always turn the unit off and unplug it from the
outlet when cleaning.
Unplug the unit if it is not going to be used for an
extended period of time.
Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
Be sure the ice maker is properly grounded.
Never plug or unplug the unit with wet hands.
Do not bypass, cut or remove the grounding plug.
Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
Do not start or stop the unit by switching the
circuit’s power on and off.
If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
Never open the unit while it is plugged in.
Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
Do not remove any part of the casing unless
instructed by an authorized technician.
You should never attempt to repair the unit
yourself.
Contact a customer service for service options if
the unit needs service.
General Safety
To prevent back and other types of injuries, use at
least two people to move and install the ice maker.
Install the ice maker in a well ventilated area where
the ambient temperature is above 50°F and below
100°F.
This unit is designed to be installed indoors, and
protected from rain, sleet, snow, etc.
This unit is not intended to be used by children.
Children should be supervised to ensure that they
do not play with this product.
Never allow children to crawl inside the ice maker.
Do not use this appliance near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
Do not place the unit near heat sources such as
ovens, and grills.
Only use in an upright position on a flat, level
surface and provide proper ventilation.
Do not pinch or kink the water or power supply lines
between the unit and cabinet.
Unit installation must be in accordance with local
plumbing code requirements.
Make sure that the water supply lines and pipes are
not pinched or kinked.
Check for leaks after installation.
Discard the first batch of cubes produced by the ice
maker.
Never turn the water supply tap off while the ice
maker is running.
If the unit has not been used for an extended period,
thoroughly clean it before using it.
Do not leave any cleaning solutions in the unit
Do not use solvent-based cleaning agents or
abrasive solutions on the interior as they may
transmit taste to the ice cubes and damage the
interior.
Only connect a potable water supply.
This appliance is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
i
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ........................................................................................................ 2
INSTALLING THE ICE MAKER ............................................................................ 3
TYPES OF INSTALLATION....................................................................................... 3
Free-standing installation: ............................................................................. 3
Recessed installation: ................................................................................... 3
Built-in installation: ........................................................................................ 3
INSTALLATION CLEARANCE REQUIREMENTS .......................................................... 4
ELECTRICAL REQUIREMENTS ................................................................................ 5
Recommended grounding method ................................................................ 5
LEVELING THE ICE MAKER .................................................................................... 6
REVERSING THE DOOR SWING .............................................................................. 6
WATER SUPPLY CONNECTIONS ............................................................................ 7
DRAIN ................................................................................................................. 7
OPERATION .......................................................................................................... 8
FINAL CHECK LIST BEFORE OPERATION ................................................................ 8
OPERATING METHOD ........................................................................................... 8
HOW THE MACHINE MAKES ICE ............................................................................. 9
HOW THE MACHINE USES THE WATER .................................................................... 9
NORMAL SOUNDS .............................................................................................. 10
PREPARING THE ICEMAKER FOR LONG STORAGE ................................................. 10
CLEANING AND MAINTENANCE ...................................................................... 11
EXTERIOR CLEANING ......................................................................................... 11
INTERIOR CLEANING ........................................................................................... 12
CONDENSER CLEANING ...................................................................................... 12
WATER DISTRIBUTION TUBE CLEANING ............................................................... 13
ICE-MAKING SYSTEM CLEANING .......................................................................... 13
TROUBLESHOOTING ........................................................................................ 15
SPECIFICATIONS ............................................................................................... 16
LIMITED WARRANTY ......................................................................................... 17
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
ice maker for the latest technical information.
KoldFront Built-in Ice Maker ii
Introduction
Thank you for purchasing this KoldFront ice maker. We are glad you chose us.
We believe that your purchase of this product opens a relationship between you
and KoldFront. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your ice maker. Following this manual will ensure that your
product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your ice maker.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to
obtain warranty service. You may also want to staple your
receipt to this manual as it is the proof of your purchase, and
is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
If you received a damaged product, immediately contact the dealer that
sold you the product.
Read and follow this instruction manual carefully to help you install, use
and maintain your ice maker.
Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resource s
and up-to-date information.
If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com or by
telephone at 1 (866) 319-5473.
1
Parts Identification
Front View
Ice Mold
Water Trough
Float
Ice Bin
Selector Switch
Hinge
Door
Back View
Leveling Foot
Control Panel
Ice Scoop
Power Plug
Water inlet
Drain outlet
KoldFront Built-in Ice Maker 2
Installing the Ice Maker
The ice maker should be installed by a licensed plumber to be in a ccordance with
local electrical and plumbing code requirements.
Before you plug the ice maker in to a power supply, be sure to let it stand upright
for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Ice Maker
WARNING: Use two more people to move and install the ice maker. Failure to do
so can result in back or other injury.
Carefully remove the packaging materials. Remove any shipping tape and glue
from your ice maker before using. Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape or glue. These products
can damage the surface of your icemaker. IMPORTANT: Do not remove any
safety , warning, or product information labels fro m your ice maker.
Types of Installation
This ice maker has been designed for free-standing, recessed, or built-in
installation. In every case, there must be adequate ventilation and access
for service.
Free-standing installation:
A free-standing installation will allow you to install the icemaker in any
place you desire provided you have access to a water supply and a drain.
You must follow the stated instructions for electrical requirements, water
supply and drain, and leveling the icemaker.
Recessed installation:
A recessed installation will allow you to install the ice maker under a
counter or in a kitchen cabinet provided the required clearance space
around the ice maker is followed. This installation has the same
requirements as a built-in installation.
Built-in installation:
It is necessary to allow adequate ventilation space around the unit (make
sure there is at least some ventilation room for the back of the unit). The
following additional items must be observed.
1. Place the ice maker in front of the installation location. Remove the
feet and place the unit flat on the floor or on a platform depending on
your installation requirements.
2. The water supply pipe must be plumbed before connecting to the ice
maker. Install the drain line into your drain.
3. Turn on main water supply and tap. Check for water supply
connection leaks. Tighten any connections (including connections at
the tie-in).
4. If the electrical outlet for the ice maker is behind the cabinet, plug in
the ice maker.
5. Push the ice maker into position.
6. Seal all around the cabinet to the floor with an approved caulking
compound.
3
Installation Clearance Requirements
* This icemaker should be installed by a licensed
plumber only.
* To ensure proper service access and ventilation,
allow more 2/5” clearance at rear, and 1” at top and
1/5” at sides. The installation should allow the
icemaker to be pulled forward for servicing if
Top View
2/5”
Back of unit
necessary.
* When installing the ice maker under a counter,
follow the recommended spacing dimensions shown.
Place electrical and water supplies and drain fixtures
in the recommended locations as shown.
* Choose a well ventilated area with temperatures
above 50°F and below 100°F.This unit MUST be
installed in an area protected from the elements,
e.g., wind, rain, water spray or drips.
* The icemaker should not be located next to ovens,
grills or other high heat resources.
* The ice maker requires a continuous water supply
with a minimum pressure of 0.05Mpa and a static
pressure not to exceed 0.8Mpa. The temperature of
the water feeding into the ice maker should be
between 41°F and 90°F for proper operation. The
ambient operational temperature should be between
50°F and 100°F. Operation outside these
1/5”
Side View
1”
1/5”
Door Hinge
temperatures may result in lowered production or
other adverse effects.
• The unit should be located on a firm and level surface. It is
important for the ice maker to be level in order to work properly. If
needed, you can adjust the height of the ice maker by rotating the
feet. See the “Leveling the Ice Maker” section.
• A standard electrical supply (115 VAC only, 60 Hz, 15 A), properly
grounded in accordance with National Electrical Code and local
codes and ordinances is required.
• IMPORTANT: Do not kink or pinch the power supply cord
between the ice maker and wall or cabinet.
KoldFront Built-in Ice Maker 4
Loading...