Kolcraft ZT005 Owner's Manual

Contours™Options™Tandem Stroller Instruction Sheet

Hoja de instrucciones de la carriola Contours

™

Options™Tandem

Feuille d'instructions pour Poussette Tandem Contours

™

Options

™

Avoid serious injury from falling or sliding out. Always use Restraint System. Your child's safety depends on you. Proper stroller use cannot be assured unless you follow these instructions. DO NOT USE STROLLER UNTIL YOU READ AND UNDERSTAND THESE INSTRUCTIONS.

IMPORTANT SAFETY INFORMATION:

How to Keep Your Child Safe While Using this Stroller

•

Adult Assembly Required.

• NEVER LEAVE YOUR CHILD UNATTENDED WHILE IN STROLLER. Accidents can happen quickly while your back is turned. You must always keep your child in view while your child is in the stroller, even when sleeping. Do not use this product as a bed. Your child may become tangled in straps or pads and suffocate.

• Always use restraint system to keep child from standing up or falling out of the stroller. Do not use product without full 5 point Harness Restraint. Removing the shoulder straps will not adequately restrain child.

• Always place the child in the front seat before placing another in the back seat. When removing children, always remove the child in the back seat first before removing the child in the front. Failure to do so may cause the stroller to become unstable and tip.

• Always lock the stroller open before allowing your child in or near the stroller. This prevents injuries caused by stroller collapsing.

•

Only use this stroller with children who weigh less than 40 lbs. (18.14 kg) or are less than 40” (1 meter) tall, per seat.

This stroller can hold a maximum of 80 lbs (36.28 kg.) dual occupancy, and use by larger children may cause it to tip.

• Use this stroller in the reclined position until child can sit up unassisted.

• Always set the wheel brakes when stroller is not moving, especially on an incline. This prevents the stroller from rolling away.

• Always fasten the canopy onto the seat back when using the stroller in the reclined position.

What to Avoid While Using this Stroller

• Always balance the weight of the stroller evenly. To prevent the stroller from becoming unstable or tipping:

• Do not place parcels or accessory items on the stroller canopy,

seat, or over the handle.

• Do not put more than 10 lbs. (4.54 kg) in the basket.

WARNING

Continued on next page

• Do not allow children to play with or hang onto the stroller.

•

When using this product with only 1 child, only use the seat or

car seat adapter in the front position.

• Never use this stroller on stairways or escalators.

• DO NOT lift by Front Bars.

• Make sure children are clear of any moving parts if you adjust the stroller, otherwise they may be injured.

• THIS IS NOT AN EXERCISE STROLLER! Do not use this product while running, jogging, in-line skating or participating in other athletic activities.

• DO NOT put child in basket.

• Take care when folding and unfolding to prevent finger pinching.

• Product may become unstable if a parcel bag, other than the one recommended by the manufacturer is used.

• DO NOT allow children to climb into stroller unassisted. Stroller may tip over and injure child.

• Only use replacement parts supplied by the manufacturer.

How to Use this Stroller with Your Infant Car Seat

• AVOID SERIOUS INJURY FROM FALLS:

•

DO NOT place carseat in stroller seat. Carseat will not be secure.

•

DO NOT use seat and infant car seat adapter in same seating location at the same time.

• This product is only to be used with certain Infant Car Seats. See

below for list of compatible Infant Car Seats.

• When using this product with your Infant Car Seat, infant must

always be secured in the car seat with the car seats harness.

• To ensure your Infant Car Seat is properly installed on the stroller, make sure it is:

• Facing the person pushing the stroller.

• Tightly secured to the stroller with the red restraint straps.

• If at any time your Infant Car Seat does not secure properly to the

stroller, or if you have questions about assembly or use of the stroller, Do Not use this product. Call Kolcraft at 1-800-453-7673.

• Make sure the stroller is fully unfolded and the car seat adapter is securely latched before attaching your Infant Car Seat. This prevents finger pinching and injuries caused by stroller collapsing.

• Only transport infants that are within the size and weight limitations of your Infant Car Seat, as described in the instruction manual provided by the Infant Car Seat manufacturer.

Continued on next page

• WHEN USING ONLY ONE INFANT CAR SEAT ADAPTER THE FOLLOWING INFANT CAR SEATS CAN BE USED:

•

WHEN USING TWO INFANT CAR SEAT ADAPTERS FOR TWINS THE FOLLOWING INFANT CAR SEATS CAN BE USED TOGETHER:

• If your Infant Car Seat is not one of the models listed above, DO NOT use your infant car seat with this stroller. Other Infant Car Seat models will not fit properly and may result in serious injury to your child.

•

DO NOT USE THE FOLLOWING CAR SEATS WITH THIS STROLLER! This list is not inclusive.

Baby Trend

, Britax®, Century®, Chicco®, Combi®, Cosco®, EvenFlo®,

Gerry®, Graco®, Peg Perego®and Safety 1st®are trademarks of their respective owners. They are not associated with Kolcraft Enterprises,

Inc. and no approval by them is to be implied.

•Britax®Baby Safe

™

•Century®535/580/590 Series

•Century

Assura®Series

•Century

Avanta™Series

•

Century®Smart Fit®Series

•

Century®Vanté™5

•

Century®Smart Fit®Series

•

Century®Take 2

•

Combi®Ty ro

™

•

Cosco®TLC

•

Cosco®Dream Ride

•

Cosco®Eddie Bauer®Caress

•

Evenflo®On-My-Way

™

•All Gerry®Infant Car Seats

•

Fisher Price®Stay in View

™

•Kolcraft®Secura

•Kolcraft

Infant Rider

•Baby Trend®Flex-Loc

•Baby Trend

Latch-Loc

•Britax

Handle with Care

•Britax®The Companion

•

Chicco®Key Fit

•Combi®Connection

™

•

Cosco®Arriva®Series

•

Cosco®Designer

•

Cosco®First Ride DX

•

Cosco®Eddie Bauer®Opus®35

•

Cosco®Turn-A-Bout

•

Evenflo®Cozy Carry

™

•

Evenflo®Discovery

™

•Evenflo®Embrace

™

•

Evenflo®Portabout

™

•

Graco®Safe Seat

™

•

Graco®Snug Ride™Series

•

PegPerego®Primo Viaggio

•

PegPerego®SIP

•

Safety 1st®Designer®22

•

Safety 1st®Starter

™

•Baby Trend®Flex-Loc

•Baby Trend

Latch-Loc

•Britax

The Companion

•Combi

Connection

™

•

Cosco®Arriva®Series

•

Cosco®First Ride DX

•

Cosco®Turn-A-Bout

•

Evenflo®Cozy Carry

™

•

Evenflo®Discovery

™

•Evenflo®Embrace

™

•

Evenflo®Portabout

™

•

Graco®Safe Seat

™

•

Graco®Snug Ride™Series

•

PegPerego®Primo Viaggio

•

Safety 1st®Designer®22

•

Safety 1st®Starter

™

To Open Stroller

Remove any cardboard inserts or plastic ties used to protect the product during shipment.

Release the locking latch on the

Stroller

Frame

Unfold to full open position.

Remove the sticker from the Front Wheel Assembly. Remove and discard both screws from the Front Wheel Assembly.

Rotate Front Wheel Assembly upward, until you hear a click.

Secure the Front Wheel Assembly into the stroller frame with 2 notched

Pins

Parts List

How to Assemble Your Stroller

Stroller Frame

with Basket

Front

Wheels (2)

Rear Wheels (2)

Washers (2) Cotter Pins (2) Hub Caps

(2)

Basket Tube

Stroller Handle

Reversible

Seats (2)

Front Bars (2) Infant Car Seat Adapter

(2) (Select Models)

Screws (6)

Pins (2)

Brake Assembly with Rear Axle

Infant Neck

Rolls (2)

(Select Models)

iPod®Mini

Adapter

(select models)

Thick iPod

Protection Pad

(select models)

Thin iPod

Protection Pad

(select models)

iPod®Dok

(select models)

Parent Tray

To Attach Basket

Align the

Basket Tube

with the Basket Frame in the rear of the stroller as shown.

Press in spring loaded buttons on

Basket

Tube

and slide into the Basket Frame

until both buttons click into place.

Unroll the basket over center bar of stroller frame as shown.

In the middle & front of the stroller, secure 4 sets of snaps on the basket around the stroller frame.

Secure 6 sets of snaps at the back end of the basket around the

Basket Tube

shown.

To Attach Stroller Handle

Slide the

Stroller Handle

down onto the stroller frame, until the holes on each side of the

Stroller Handle

can be seen

in the frame.

Secure the

Stroller Handle

with a screw

on each side of the frame.

To Attach Parent Tray

Place the

Parent Tray

onto the bar

underneath the

Stroller Handle

and align

the

Parent Tray

into the 4 holes. The

Parent Tray

should be positioned so the

lid opening is towards the handle.

Secure the

Parent Tray

to the bar with 4

screws as shown.

To remove

Parent Tray

, unscrew from

frame. For cleaning,

Parent Tray

is top

rack dishwasher safe.

WARNING

Do not place more than 3 lbs. (1.36 kg) in this tray to avoid tipping! Do not place hot liquids in this tray. Hot liquids can burn your child.

Screws (4)

Button

To Attach Front Wheels

Align

Front Wheel

as shown.

Push

Front Wheel

up into the Front

Wheel Assembly until a “Click” is heard.

Repeat for other wheel. Tug firmly on each wheel assembly to be sure wheels are securely in place.

NOTE: To remove

Front Wheels

, twist top of Front Wheel Assembly as shown, and pull wheel off.

To Assemble Rear Wheels

Turn stroller over as shown. Remove protective sleeve from ends of brake assembly with rear axle.

Position

Brake Assembly

as shown, with brake levers pointing towards stroller handle.

Push both brake assemblies onto rear leg tubes at the same time until spring loaded buttons click into place.

NOTE: If brake assemblies do not click and hold in place, the spring button is stuck and not protruding through the hole in the tube. Use a screwdriver or pliers to move the button so that it protrudes out of the hole in the tube.

Continued on next page

Brake Levers

1 & 2

Slide

Rear Wheel

onto axle.

Slide

Washer

onto axle.

Fit straight part of

Cotter Pin

through

hole on axle as shown.

Line up tabs in the

Hub Cap

with slots in

the wheel, snap hub cap into place.

Repeat for second side.

4 - 7

To Attach Infant Car Seat Adapter (select models)

Align

Infant Car Seat Adapter

catches over frame hubs as shown and push Infant Car Seat Adapter down onto the frame hubs until a “Click” is heard. Make sure the “Front / Frente” sticker on the adapter is facing the front of the stroller.

The button on the frame hubs should be seen through both

Infant Car Seat

Adapter

catches. Pull up on the Infant Car Seat Adapter to make sure it is securely attached.

NOTE: To remove

Infant Car Seat

Adapter

, push both buttons on the frame hub in, then lift the Infant Car Seat Adapter up.

Attaching a Second Infant Car Seat Adapter

(sold separately - through Consumer

Service see page 59)

Follow Steps 1 and 2, by installing the Infant Car Seat Adapter to the frame hubs towards the front of the stroller.

Frame Hub & Button

Infant Car Seat Adapter Catches

Front Sticker

To Attach Front Bars

Seat Catch Hole

Front Bar Pin

Front Bar Release Button

Align

Front Bar

pins over the holes on the Seat Catch and push in, until a “Click” is heard on both sides. Repeat this Step for other

Front Bar

To let a child in/out of a

Reversible Seat

push on one side, of the

Front Bar

release button and pull the Front Bar out. The Front bar will now swivel outward. Repeat Step 1 to reinsert

Front Bar

To remove

Front Bar

, push both

Front

Bar

realease buttons and pull out.

Repeat Step 1 to reinsert.

CAUTION

To prevent injury to your child, take care when inserting bar into frame.

When using this product with only 1 child, only use the seat or car seat adapter in the front position.

To Attach Reversible Seats

Frame Hub & Button

Seat Catches

Reversible Seats can be positioned in these directions: A. Facing Parent B. Facing Away from Parent C. Facing Each Other D. Back to Back E. One Child Use (Seat or Infant Car Seat Adapter must be attached on front frame hub ONLY to avoid tipping).

Align

Reversible Seat

catches over frame hubs as shown and push Reversible Seat down onto the frame hubs until a “Click” is heard on both sides.

The button on the frame hubs should be seen through both

Reversible Seat

catches. Pull up on the seat to make sure the seat is securely attached.

Repeat Steps 1 and 2 for other

Reversible Seat

NOTE: To remove

Reversible Seat

, push both buttons on the frame hub in, than lift the Reversible Seat up.

WARNING

To Assemble iPod®Dok (select models)

Determine which iPod®model you own (iPod®mini, 60GB iPod®, 40GB iPod®, 30GB iPod®or the 20GB iPod®). See www.apple.com for assistance in determining which model you have.

If you own the iPod®mini, proceed to Step 3. For all other models, remove the iPod®mini adapter by flexing the snap tab and pulling up on the adapter.

Release the snap that holds the iPod

Dok in the closed or portable position.

Select the proper donut-shaped protection pad for your iPod®. For the mini, 30GB or 20GB iPod®, select the thick donut-shaped protection pad with yellow backing paper. For the 60GB or 40GB iPod®, select the thin donut-shaped protection pad with white backing paper. Remove the backing paper from the foam, and place the adhesive side of the foam pad onto the back of the speaker housing.

Insert your iPod®into the iPod®Dok or insert your iPod®mini into the iPod

adapter. Insert the speaker Jack into your iPod®device.

For use on a flat surface such as a table top, rest the iPod

Dok on the surface in the open position. For portable use with your stroller, push the speaker housing and the iPod®cradle together until you hear a snap. DO NOT turn the iPod

Dok upside down, unless the Dok is in the closed or latched position.

Power and volume of the iPod

Dok are controlled through your iPod®device. Turn on your iPod®and adjust the volume of your iPod®to a desired level.

NOTE: Song volume and clarity will vary with the quality of the song data that you downloaded to your iPod®.

WARNING

DO NOT turn the iPod®Dok upside down, unless the Dok is in the closed and latched position. iPod®could fall out.

How to Properly Use Your New Stroller

To Operate Brakes

Push levers on both rear wheels down to lock.

Pull levers up to unlock.

Unlock

Lock

To Insert iPod Dok to Canopy (select models)

Insert iPod Dok into the pocket provided on the stroller canopy with the speaker facing the mesh or toward the child seat.

Ensure that the cover for the pocket is securely latched by the Velcro.

CAUTION

Loud volume can damage your baby’s hearing. When turning on music, gradually adjust the volume to a comfortable listening level so baby’s not startled.

Lowest Center Point

WARNING

To Secure All Acceptable Infant Car Seats (select models)

Baby’s head should be slightly above their knees for added comfort. Also, make sure Infant Car Seat is not too upright when placed in adapter. Finally, keep car seat handle up to avoid interferring with other child.

Lock both foot brakes to keep stroller from rolling.

With one hand, grasp the Infant Car Seat handle (in its upright, carrying position). With your other hand, grasp Infant Car Seat near baby’s feet. Gently position the Infant Car Seat above

Infant Car Seat

Adapter

so the baby faces the stroller

handle.

Lower the Infant Car Seat between the front & rear bars. Remove restraint buckles from bag.

For a secure fit, wrap restraint straps around the frame and position through Infant Car Seat belt slots and buckle. Tighten Restraint Straps.

Special

Instructions

for Car Seats without belt

slots: Secure Infant Car Seat to

Adapter

by wrapping restraint around frame and over seats lowest center point near handle and buckle them together. Tighten Restraint Straps.

NOTE: Shopping cart lever will not lock onto the carrier. To secure infant car seat to carrier, use restraint straps.

When using this product, to avoid serious injury from falling or sliding out, infant must always be secured in the Infant Car Seat with the Car Seat harness. Refer to Infant Car Seat Instructions for proper adjustment.

Continued on next page

Restraint Buckle Bag

To Secure Infant Car Seat

To fasten car seat restraint belts - open up loop of the restraint belt. Adjust belt until the buckles almost touch.

Pull end tab of restraint belt to set. Push buckles together to secure.

To unsnap Restraint Belt - press tabs.

Make sure Infant Car Seat is secure. Test Infant Car Seat installation by moving it in all directions to ensure a tight fit to

Adapter

NOTE: Your Infant Car Seat may have a level indicator. It is not necessary for use with this carrier and the indicator may fall outside the recommended area. The level indicator is for use while the Infant Car Seat is in an automobile. Your childs head should always be above their knees.

To Remove Infant Car Seat

Unbuckle Restraint Belts and remove them from Car Seat belt slots.

With one hand grasp the Infant Car Seat carry handle (in its upright, carrying position).

To Adjust Footrest

Footrest can be adjusted for childs comfort. Push in side buttons to adjust.

Infant neck roll is to be used with newborns who can not hold up their head. It should be used only when the seat is reclined. It can be removed when a child can hold their head up unassisted.

When using the infant neck roll, be sure that the shoulder restraint straps are fed through the holes on either side. Restraint must always be used with the infant neck roll.

To Install Infant Neck Roll (select models)

To Recline Seat

To recline seat, pull adjustment bar located on the top of the seat to one of 3 positions:

• Upright

• Middle

• Full Recline

NOTE: For both seats to recline fully, the seats are best positioned when Facing Parent or Facing Away from Parent. Footrests may need to be adjusted for child’s comfort.

Make sure Velcro on canopy are secured to seatback while seat is in the reclined position.

WARNING

To avoid finger entrapment or pinching, do not adjust the seat back while child is in the stroller. To avoid head entrapment, always fasten the canopy to the seat back when using the stroller in the reclined position.

Adjustment Bar

Hold On Handles (select models)

Hold on handles are designed to be used with older children walking beside parent.

Hold On

Handles

To Secure Child In Stroller Seat

Lock foot brake to keep stroller from rolling.

Place child in stroller.

Hook shoulder straps to waist belt.

To fasten restraint system buckles - push together. Be sure both buckles are fastened to secure child safely.

To unsnap restraint system buckles press tabs to release.

For proper fit, adjust shoulder straps and waist band as shown.

WARNING

Avoid serious injury from falling or sliding out. Always use restraint system. Do not use product without full 5-point Harness Restraint. Removing the shoulder straps will not adequately restrain child.

Adjust Restraint System Harness

NOTE: For a secure fit, straps should be at or below the child's shoulder. Adjust straps to higher position as your child grows.

To readjust shoulder restraints, turn the plastic toggle and thread through the slot from the back of the seat.

To position the shoulder strap to a higher position, push plastic toggle through top front slot as shown. Repeat for second side.

Make sure toggles are horizontal and flat against the back of the seat.

To Adjust Shoulder Strap Height

Lower Higher

To Fold Stroller

Lock brakes.

For the tightest fold, either:

a) Remove rear seat or Infant car seat

adapater and make sure front seat is facing handle.

b) Remove front seat and make sure

Rear Seat is facing forward.

c) Remove both seats.

Close canopy.

Pull up on triggers and push stroller handle forward slightly.

Step down on basket lever with foot and push stroller handle forward, allowing the stroller to become compact.

Engage locking latch.

Continued on next page

+ 44 hidden pages