Kolcraft ZL008 Owner's Manual
Contours®Options®3 Wheeler Stroller Instruction Sheet
®
Hoja de instrucciones de la carriola Contours
Options®de 3 ruedas
Feuille d’instructions pour la poussette à 3 roues Contours
®
Options
®
©2008 Kolcraft®Enterprises, Inc. S74-T-R2 6/08
WARNING
Avoid serious injury from falling or sliding out. Always use Restraint
System. Your child's safety depends on you. Proper stroller use cannot be
assured unless you follow these instructions. DO NOT USE STROLLER
UNTIL YOU READ AND UNDERSTAND THESE INSTRUCTIONS.
IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNFFOORRMMAATTIIOONN::
HHooww ttoo KKeeeepp YYoouurr CChhiilldd SSaaffee WWhhiillee UUssiinngg tthhiiss SSttrroolllleerr
AAdduulltt AAsssseemmbbllyy RReeqquuiirreedd..
•
NNEEVVEERR LLEEAAVVEE YYOOUURR CCHHIILLDD UUNNAATTTTEENNDDEEDD WWHHIILLEE IINN SSTTRROOLLLLEERR
•
Accidents can happen quickly while your back is turned. You must
always keep your child in view while your child is in the stroller,
even when sleeping. Do not use this product as a bed. Your child
may become tangled in straps or pads and suffocate.
AAllwwaayyss uussee rreessttrraaiinntt ssyysstteemm ttoo kkeeeepp cchhiilldd ffrroomm ssttaannddiinngg uupp oorr
•
ffaalllliinngg oouutt ooff tthhee ssttrroolllleerr..
harness restraint. Removing the shoulder straps will not adequately
restrain child.
AAllwwaayyss lloocckk tthhee ssttrroolllleerr ooppeenn bbeeffoorree aalllloowwiinngg yyoouurr cchhiilldd iinn oorr nneeaarr
•
tthhee ssttrroolllleerr..
OOnnllyy uussee tthhiiss ssttrroolllleerr wwiitthh cchhiillddrreenn wwhhoo wweeiigghh lleessss tthhaann 4400 llbbss.. ((1188..11
•
kkgg)) oorr aarree lleessss tthhaann 4400”” ((11 mmeetteerr)) ttaallll,, aanndd wwhhoo’’ss hheeaadd rreessttss bbeellooww tthhee
ttoopp ooff tthhee sseeaatt bbaacckk..
or cause a hazardous unstable condition to exist.
UUssee tthhiiss ssttrroolllleerr iinn tthhee rreecclliinneedd ppoossiittiioonn uunnttiill cchhiilldd ccaann ssiitt uupp
•
uunnaassssiisstteedd..
AAllwwaayyss sseett tthhee wwhheeeell bbrraakkeess wwhheenn ssttrroolllleerr iiss nnoott mmoovviinngg,, eessppeecciiaallllyy
•
oonn aann iinncclliinnee..
AAllwwaayyss ffaasstteenn tthhee ccaannooppyy oonnttoo tthhee sseeaatt bbaacckk wwhheenn uussiinngg tthhee
•
ssttrroolllleerr iinn tthhee rreecclliinneedd ppoossiittiioonn..
WWhhaatt ttoo AAvvooiidd WWhhiillee UUssiinngg tthhiiss SSttrroolllleerr
AAllwwaayyss bbaallaannccee tthhee wweeiigghhtt ooff tthhee ssttrroolllleerr eevveennllyy..
•
stroller from becoming unstable or tipping:
• Do not place parcels or accessory items on the stroller canopy,
seat, or over the handle.
• Do not put more than 10 lbs. (4.54 kg) in the basket.
• Do not allow children to play with or hang onto the stroller.
NNeevveerr uussee tthhiiss ssttrroolllleerr oonn ssttaaiirrwwaayyss oorr eessccaallaattoorrss..
•
DDOO NNOOTT lliifftt bbyy ffrroonntt bbaarr..
•
MMaakkee ssuurree cchhiillddrreenn aarree cclleeaarr ooff aannyy mmoovviinngg ppaarrttss
•
stroller, otherwise they may be injured.
This prevents injuries caused by stroller collapsing.
This prevents the stroller from rolling away.
Do not use product without full 5 point
Use by larger children may damage the stroller,
To prevent the
if you adjust the
Continued on next page
2
.
TTHHIISS IISS NNOOTT AANN EEXXEERRCCIISSEE SSTTRROOLLLLEERR!
•
!
Do not use this product while
running, jogging, in-line skating or participating in other athletic
activities.
DDOO NNOOTT ppuutt cchhiilldd iinn bbaasskkeett..
•
TTaakkee ccaarree wwhheenn ffoollddiinngg aanndd uunnffoollddiinngg ttoo pprreevveenntt ffiinnggeerr ppiinncchhiinngg..
•
• Product may become unstable if a parcel bag, other than the one
recommended by the manufacturer is used.
DDOO NNOOTT
•
allow children to climb into stroller unassisted. Stroller
may tip over and injure child.
• Only use replacement parts supplied by the manufacturer.
HHooww ttoo UUssee tthhiiss SSttrroolllleerr wwiitthh YYoouurr IInnffaanntt CCaarr SSeeaatt
AAVVOOIIDD SSEERRIIOOUUSS IINNJJUURRYY FFRROOMM FFAALLLLSS::
•
DDOO NNOOTT
•
DDOO NNOOTT
•
• This product is only to be used with certain Infant Car Seats. See
place carseat in stroller seat. Car seat will not be secure.
use seat and infant car seat adapter at the same time.
below for list of compatible Infant Car Seats.
• When using this product with your Infant Car Seat, infant must
always be secured in the car seat with the car seat harness.
• To ensure your Infant Car Seat is properly installed on the stroller,
make sure it is:
• Facing the person pushing the stroller.
• Tightly secure to the stroller with the car seat adapter’s restraint
straps.
• If at any time your Infant Car Seat does not secure properly to the
stroller, or if you have questions about assembly or use of the
stroller,
MMaakkee ssuurree tthhee ssttrroolllleerr iiss ffuullllyy uunnffoollddeedd aanndd tthhee ccaarr sseeaatt aaddaapptteerr iiss
•
DDoo NNoott
use this product.
sseeccuurreellyy llaattcchheedd bbeeffoorree aattttaacchhiinngg yyoouurr IInnffaanntt CCaarr SSeeaatt..
CCaallll KKoollccrraafftt aatt 11--880000--445533--77667733..
This
prevents finger pinching and injuries caused by stroller collapsing.
OOnnllyy ttrraannssppoorrtt iinnffaannttss tthhaatt aarree wwiitthhiinn tthhee ssiizzee aanndd wweeiigghhtt
•
lliimmiittaattiioonnss ooff yyoouurr IInnffaanntt CCaarr SSeeaatt,, aass ddeessccrriibbeedd iinn tthhee iinnssttrruuccttiioonn
mmaannuuaall pprroovviiddeedd bbyy tthhee IInnffaanntt CCaarr SSeeaatt mmaannuuffaaccttuurreerr..
TTHHEE FFOOLLLLOOWWIINNGG IINNFFAANNTT CCAARR SSEEAATTSS CCAANN BBEE UUSSEEDD IINN CCAARR
•
SSEEAATT AADDAAPPTTEERR::
•
Baby Trend®Latch-Loc
•
Century®Avanta™Series
•
Century®Vanté™5
•
Chicco®Key Fit
•
Combi®Tyro
Combi®Connection
•
•
Cosco®Arriva®Series
™
™
TM
®
®
®
™
Series
Caress
•
Cosco®Designer 22
•
Cosco®Eddie Bauer®Opus
•
Cosco® Eddie Bauer
•
Cosco®First Ride DX
•
Cosco®Turn-A-Bout
•
Evenflo®Discovery
Evenflo® Embrace
•
•
Evenflo®On-My-Way
•
Graco®Snug Ride™ Series
®
®
•
Graco® Safe Seat
35
•
Maxi Cosi Micro
•
Peg Perego®Primo Viaggio
•
Peg Perego®SIP
•
Safety 1st®Designer® 22
•
Safety 1st®Starter
™
™
™
™
3
Continued on next page
IIff yyoouurr IInnffaanntt CCaarr SSeeaatt iiss nnoott oonnee ooff tthhee mmooddeellss lliisstteedd aabboovvee,, DDOO
•
NNOOTT uussee yyoouurr iinnffaanntt ccaarr sseeaatt wwiitthh tthhiiss ssttrroolllleerr.. OOtthheerr IInnffaanntt CCaarr
SSeeaatt mmooddeellss wwiillll nnoott ffiitt pprrooppeerrllyy aanndd mmaayy rreessuulltt iinn sseerriioouuss iinnjjuurryy ttoo
yyoouurr cchhiilldd..
••
DDOO NNOOTT UUSSEE TTHHEE FFOOLLLLOOWWIINNGG CCAARR SSEEAATTSS WWIITTHH TTHHIISS SSTTRROOLLLLEERR!!
TThhiiss lliisstt iiss nnoott iinncclluussiivvee..
•
Britax®Baby Safe
•
Britax®Companion
•
Britax®Handle with Care
•
Century®535/580/590 Series
•
Century®Assura®Series
™
®
•Century
•
Cosco®TLC
•
Cosco®Dream Ride
•
Evenflo®Cozy Carry™
•
Evenflo®Portabout™
®
Smart Fit
TM
Series
®
•
Fisher Price®Stay in View
•
All Gerry®Infant Car Seats
•
Kolcraft®Secura
•
Kolcraft®Infant Rider
®
™
Baby Trend®, Britax®, Century®, Chicco®, Combi®, Cosco®, EvenFlo®, Gerry®,
Fisher Price®, Graco®, Peg Perego®and Safety 1st®are trademarks of their
respective owners. They are not associated with Kolcraft Enterprises, Inc. and
no approval by them is to be implied.
Parts List
Stroller Frame
Left Brake
Assembly
Front Bar
Seat Infant Car Seat
Right Brake
Assembly
Rear Brake Tube
1/2” Screws (6)
Front Wheel
Assembly
Canopy
1” Screws (2)
4
Adapter
Parent Tray
Washers
Rear Axle
(6)
Rear Wheels (2)
Wheel Cover
Cotter Pins
(2)
Hub Caps
(2)
How to Assemble Your Stroller
To Open Stroller
Remove any cardboard inserts or plastic
1
ties used to protect the product during
2
shipment.
Release the locking latch.
2
2
Side
locks
1
3
Unfold, making sure both side locks on
3
each side of the stroller snap into place.
TToo TTeesstt ffoorr uussee::
push down on handle to make sure it is
fully engaged.
First pull up and then
To Assemble Brake Assembly
Secure Right Brake Assembly to Brake
1
tube using 2 screws. Please note the
curve of the tube should be curving
towards inside as shown.
Place one washer onto end of rear axle.
2
Insert rear axle with washer into right
3
brake assembly hub.
Repeat for left side.
4
3
4
5
To Assemble Rear Wheels
Position brake assembly as shown, with
1
brake levers pointing towards stroller
handle.
Push both sides of brake assembly onto
1
2
4
5
2
rear leg tubes at the same time until
spring loaded buttons click into place.
Lay stroller on its side.
3
Slide a rear wheel onto the axle than
4
slide a washer onto the axle.
Fit straight part of cotter pin through
5
hole on axle as shown.
Line up each of the tabs in the hub cap
6
with the slots in the wheel, snap hub cap
into place.
Repeat for second side.
7
6
Spring
Loaded
Buttons
2
To Assemble Front Wheel & Attach Wheel Cover
Place stroller back on handle bar.
1
Slide front wheel assembly onto frame.
2
3
Spring
Loaded
Buttons
NNOOTTEE::
buttons pop through frame. If your
spring loaded button becomes out of
place, take pliers and feed button into
hole.
CCAAUUTTIIOONN::
NOT pop through, front wheel assembly
could fall off during use.
Secure front wheel assembly to the front
3
frame tubes using 1/2” screws. The 1/2”
screws should be aligned into the 2
holes closest to the spring loaded buttons. Secure with a Phillips screwdriver
on both sides.
Align bosses underneath wheel cover to
4
the two holes on the metal frame. If
4
bosses DO NOT line up, wheel cover on
front wheel is not on correctly. Repeat
steps 1-3. If you are still having trouble,
call customer service for assistance.
Make sure that spring loaded
If spring loaded buttons DO
5
Secure wheel cover into remaining holes
5
underneath frame by basket with 1”
screws using a Phillips screwdriver.
Repeat for second side.
7
To Attach Seat
Release levers
Forward Position Reverse Position
1
Seat
Tab
Side Rail
Slot
To Attach Front Bar
WARNING
DDOO NNOOTT
seat. Car seat will not be secure.
Place stroller upright with all 3 wheels on
1
ground.
Pick up seat frame with handle and place
2
seat in either forward or reverse position.
Align seat tabs with side rail slot as
3
shown.
Press seat down until a “click” is heard.
4
Pull up on seat to make sure it is secured
to the frame.
To reverse seat, push in release levers
5
located underneath handles and lift up.
NNOOTTEE::
designed to give your child a
comfortable ride.
Place car seat in stroller
Springs in seat frame are
1 & 2
Release Button
CAUTION
To prevent injury to your child, take
care when inserting bar into frame.
Align bar into holes located on seat
1
frame.
Snap tab in place until a click is heard.
2
Repeat for second side.
3
TTOO RROOTTAATTEE OORR RREEMMOOVVEE BBAARR::
release button located near side housing
and pull bar out. Repeat on other side,
to remove bar completely.
8
Push in
To Attach Parent Tray
1
DDOO NNOOTT
(1.36 kg) in this tray to avoid tipping!
DDOO NNOOTT
Hot liquids can burn your child.
1
WARNING
place more than 3 lbs.
place hot liquids in this tray.
Align tray holes with posts near handle
and snap on.
TTOO RREEMMOOVVEE
For cleaning, parent tray is top rack
dishwasher safe.
, pull each side up and out.
To Attach Canopy
Slide canopy on as shown.
1
1
To Assemble Adjustable Footrest Mechansism to Seat
1
Align both sides of adjustable footrest
1
mechanism with seat tube frame as
shown.
Push adjustable footrest mechanism
2
onto seat tube until spring loaded
button clicks into place.
2
Push Together
Spring Loaded Button
NNOOTTEE::
buttons pop through frame. If your
spring loaded button becomes out of
place, take pliers and feed button into
hole.
Make sure that spring loaded
9
How to Properly Use Your New Stroller
To Operate Brakes
Unlock
TTOO LLOOCCKK BBRRAAKKEE::
1
bar down to lock wheels.
TTEESSTT::
Push stroller slightly to make sure
brakes are engaged.
Push 1-Touch brake
Lock
TTOO UUNNLLOOCCKK BBRRAAKKEE::
2
bar.
Lift up on brake
To Secure Child In Stroller
WARNING
Avoid serious injury from falling or sliding
out. Always use restraint system. Do not
use product without full 5-point Harness
Restraint. Removing the shoulder straps
will not adequately restrain child.
3
4
Lock foot brake to keep stroller from
1
rolling.
Place child in stroller.
2
Hook shoulder straps to waist belt.
3
6
Adjust Restraint
System Harness
10
To fasten restraint system buckles -
4
push together. Be sure both buckles
are fastened to secure child safely.
To unsnap restraint system buckles -
5
press tabs to release.
For proper fit, adjust shoulder straps and
6
waist band as shown.
To Adjust Shoulder Strap Height
Lower
1
2
Higher
NNOOTTEE::
at or below the child's shoulder. Adjust
straps to higher position as your child
grows.
To readjust shoulder restraints, turn the
1
plastic toggle and thread through the
slot from the back of the seat.
To position the shoulder strap to a
2
higher position, push plastic toggle
through top front slot as shown.
Repeat for second side.
Make sure toggles are horizontal and flat
3
against the back of the seat.
For a secure fit, straps should be
3
To Adjust Footrest
Footrest can be adjusted for child’s
1
comfort. Push in side buttons to adjust.
11
To Operate Swivel Wheel Lock
LLOOCCKK FFRROONNTT SSWWIIVVEELL::
1
located under wheel cover. Adjust front
wheel so that wheel is straight and lock
is forward. Push lock to right.
UUNNLLOOCCKK FFRROONNTT SSWWIIVVEELL::
2
left.
NNOOTTEE::
wheel to keep straight. On smooth
surfaces, unlock to allow the wheel to
swivel.
On rough surfaces, lock the
Push lock
Push lock to
To Install Infant Neck Roll
1
Infant neck roll is to be used with newborns who can not hold up their head. It
should be used only when the seat is
reclined. It can be removed when a child
can hold their head up unassisted.
When using the infant neck roll, be sure
1
that the shoulder restraint straps are fed
through the holes on either side.
Restraint must always be used with the
infant neck roll.
To Recline Seat
1
Adjustment Bar
WARNING
To avoid finger entrapment or pinching, do
not adjust the seat back while child is in the
stroller. To avoid head entrapment, always fasten the canopy to the seat back when using
the stroller in the reclined position.
To recline seat, pull adjustment bar
1
located on the back of the seat to
one of 3 positions.
• Upright
• Middle (2 positions)
Make sure snaps and velcro on canopy
2
are secured to seatback while seat is in
the reclined position.
12
To Install and Use Infant Car Seat Adapter
2
Black
Bumpers
1 & 2
3
3
Restraint Bag
Restraint Bag
To Secure All Acceptable Infant Car Seats
Belt Slots
Lowest Center Point
Front Bar
Side Rail
Slot
To remove seat, push in release levers
1
located underneath handles and lift up.
Align Infant Car Seat Adapter as shown
2
with the black bumpers toward the back
of the frame.
Push adapter into side rail slots until a
3
click is heard on both sides. Pull up on
adapter to make sure it is secured to the
frame.
WARNING
When using this product, to avoid serious injury from falling or sliding out,
infant must always be secured in the
Infant Car Seat with the Car Seat harness. Refer to Infant Car Seat
Instructions for proper adjustment.
With one hand, grasp the Infant Car Seat
1
handle (in its upright, carrying position).
With your other hand, grasp Infant Car
Seat near baby’s feet. Gently position the
Infant Car Seat above Infant Car Seat
Adapter so the baby faces the stroller
handle.
Lower the Infant Car Seat between
2
the front & rear bars. Remove restraint
buckles from bag.
For a secure fit, wrap restraint straps
3
through Infant Car Seat belt slots and
buckle. Tighten Restraint Straps.
IInnssttrruuccttiioonnss
slots: Secure Infant Car Seat to Adapter
by wrapping restraint over seats lowest
center point near handle and buckle them
together. Tighten Restraint Straps.
NNOOTTEE::
onto the carrier. To secure infant car seat
to carrier, use restraint straps.
for Car Seats without belt
Shopping cart lever will not lock
SSppeecciiaall
13
To Fold Stroller
5
7
3 & 4
4B
4A
Lock brakes.
1
Put seat in the upright position.
2
Close canopy fully, pushing down past
3
3
top of seat.
Lightly press down on handle by latches
4
and pull triggers to release.
Push handle forward until it reaches a
5
straight up position (do not rotate past
top of seat).
Gently lift up handle until “click” is
6
heard.
Then push handle down and lock folding
7
latch.
NNOOTTEE::
the reverse position but the lock will not
latch.
Stroller will fold when seat is in
7
Care & Maintenance
• To keep your stroller running smoothly and avoid squeaking wheels use a silicon
or graphite based lubricant. It is important to get it into the axle and the wheel
assembly.
• Clean metal parts with a damp cloth and wipe dry.
• Clean woven fabric or vinyl parts with mild soap and water solution.
• Dry wet stroller with a soft cloth to prevent rusting.
• When storing stroller, never stack other items on top of it; this may damage the stroller.
• Periodically check for worn parts, loose screws, torn materials or stitching.
• Replace any damaged parts immediately.
14
Loading...