Kolcraft ZL005 Owner's Manual

Contours™Options™4 Wheeler Stroller Instruction Sheet

Hoja de instrucciones de la carriola Contours

™

Options™de 4 ruedas

Feuille d’instructions pour la poussette à 4 roues Contours

™

Options

™

Avoid serious injury from falling or sliding out. Always use Restraint System. Your child's safety depends on you. Proper stroller use cannot be assured unless you follow these instructions. DO NOT USE STROLLER UNTIL YOU READ AND UNDERSTAND THESE INSTRUCTIONS.

IMPORTANT SAFETY INFORMATION:

How to Keep Your Child Safe While Using this Stroller

•

Adult Assembly Required.

• NEVER LEAVE YOUR CHILD UNATTENDED WHILE IN STROLLER. Accidents can happen quickly while your back is turned. You must always keep your child in view while your child is in the stroller, even when sleeping. Do not use this product as a bed. Your child may become tangled in straps or pads and suffocate.

• Always use restraint system to keep child from standing up or falling out of the stroller. Do not use product without full 5 point harness restraint. Removing the shoulder straps will not adequately restrain child.

• Always lock the stroller open before allowing your child in or near the stroller. This prevents injuries caused by stroller collapsing.

•

Only use this stroller with children who weigh less than 40 lbs. (18.14 kg) or are less than 40” (1 meter) tall.

Use by larger children may damage the stroller, or cause a hazardous, unstable condition to exist.

• Use this stroller in the reclined position until child can sit up unassisted.

• Always set the wheel brakes when stroller is not moving, especially on an incline. This prevents the stroller from rolling away.

• Always fasten the canopy onto the seat back when using the stroller in the reclined position.

What to Avoid While Using this Stroller

• Always balance the weight of the stroller evenly. To prevent the stroller from becoming unstable or tipping:

• Do not place parcels or accessory items on the stroller canopy,

seat, or over the handle.

• Do not put more than 10 lbs. (4.54 kg) in the basket.

• Do not allow children to play with or hang onto the stroller.

• Never use this stroller on stairways or escalators.

• DO NOT lift by tray.

• Make sure children are clear of any moving parts if you adjust the stroller, otherwise they may be injured.

WARNING

Continued on next page

• This is not an exercise stroller! Do not use this product while running, jogging, in-line skating or participating in other athletic

activities.

• DO NOT put child in basket.

• Take care when folding and unfolding to prevent finger pinching.

• Product may become unstable if a parcel bag, other than the one recommended by the manufacturer is used.

• DO NOT allow children to climb into stroller unassisted. Stroller may tip over and injure child.

• Only use replacement parts supplied by the manufacturer.

How to Use this Stroller with Your Infant Car Seat

• AVOID SERIOUS INJURY FROM FALLS:

•

DO NOT place carseat in stroller seat. Car seat will not be secure.

•

DO NOT use seat and infant car seat adapter at the same time.

• This product is only to be used with certain Infant Car Seats. See

below for list of compatible Infant Car Seats.

• When using this product with your Infant Car Seat, infant must

always be secured in the car seat with the car seat harness.

• To ensure your Infant Car Seat is properly installed on the stroller, make sure it is:

• Facing the person pushing the stroller.

• Tightly secure to the stroller with the car seat adapter’s restraint

straps.

• If at any time your Infant Car Seat does not secure properly to the

stroller, or if you have questions about assembly or use of the stroller, Do Not use this product. Call Kolcraft at 1-800-453-7673.

• Make sure the stroller is fully unfolded and the car seat adapter is securely latched before attaching your Infant Car Seat. This prevents finger pinching and injuries caused by stroller collapsing.

• Only transport infants that are within the size and weight limitations of your Infant Car Seat, as described in the instruction manual provided by the Infant Car Seat manufacturer.

• THE FOLLOWING INFANT CAR SEATS CAN BE USED IN CAR SEAT ADAPTER:

•

Baby Trend®Latch-Loc

•

Baby Trend

Flex-Loc

•

Britax® Handle with Care

•

Chicco®Key Fit

•

Combi®Ty ro

™

•

Combi®Connection

™

•

Cosco®Arriva®Series

•

Cosco®Designer 22

Series

•

Cosco®Eddie Bauer®Opus

•

Cosco® Eddie Bauer

Caress

•

Cosco®First Ride DX

•

Cosco®Turn-A-Bout

•

Evenflo®Cozy Carry

™

•

Evenflo®Discovery

™

•

Evenflo® Embrace

•

Evenflo®On-My-Way

™

•

Evenflo®Portabout

™

•

Graco®Snug Ride™ Series

•

Graco® Safe Seat

™

•

Peg Perego®Primo Viaggio

•

Peg Perego®SIP

•

Safety 1st®Designer® 22

™

•

Safety 1st®Starter

™

Continued on next page

Parts List

Stroller Frame

Rear Wheels

(2)

Brake Assembly

Right (with ★)

Front Tray

Seat

Infant Car Seat Adapter

Washers

(2)

Cotter

Pins (2)

Hub Caps

(2)

Cup Holder

(select models)

Front Wheel

Assembly Right

(with ▲)

Rear Axle

Brake Assembly

Left (with ▲)

Canopy

• If your Infant Car Seat is not one of the models listed above, DO NOT use your infant car seat with this stroller. Other Infant Car Seat models will not fit properly and may result in serious injury to your child.

•

DO NOT USE THE FOLLOWING CAR SEATS WITH THIS STROLLER! This list is not inclusive.

Baby Trend®, Britax®, Century®, Chicco®, Combi®, Cosco®, EvenFlo®, Gerry®, Fisher Price®, Graco®, Peg Perego®and Safety 1st®are trademarks of their respective owners. They are not associated with Kolcraft Enterprises, Inc. and no approval by them is to be implied.

•

Britax®Baby Safe

™

•

Britax®Companion

•

Century®535/580/590 Series

•

Century®Assura®Series

•

Century®Avanta™Series

•

Century®Vanté™5

•Century

Smart Fit

Series

•

Cosco®TLC

•

Cosco®Dream Ride

•

Eddie Bauer® Caress

•

Fisher Price®Stay in View

™

•

All Gerry®Infant Car Seats

•

Kolcraft®Secura

•

Kolcraft®Infant Rider

Front Wheel

Assembly Left

(with ★)

How to Assemble Your Stroller

To Open Stroller

Remove any cardboard inserts or plastic ties used to protect the product during shipment.

Release the locking latch.

NOTE: Keep hands/fingers away from side locks when unfolding the handle!

Place one hand on the foam grip located on the basket (A) and the other on the side lock (B). Gently pull apart to seperate.

Rotate handle back until side locks and frame click into place. Push down on basket tube with hand or foot to confirm the lower frame is locked.

NOTE: You can tell if lower frame is in locked position by looking at the square window in the lower frame lock. If a red tab appears in that window, the lower frame is locked.

To Test for use: First pull up and then push down on handle to make sure it is fully engaged.

2 & 3

Pull Apart

Locking Latch

Pull Apart

Side Locks

Lower Frame Lock Tab

Push Down

Lower Frame Lock

3 & 4

To Assemble Rear Wheels

1 & 2

There is a LEFT and RIGHT brake assembly. Be sure to assemble them onto the correct rear leg tube. LEFT from RIGHT will be identified as shown. Each brake assembly will have either a triangle or a star on the bottom of the part.

• TRIANGLE = “▲” LEFT

• STAR = ”★“ RIGHT

Position brake assembly as shown, with the brake lever pointing towards the stroller handle. Push brake assembly completely onto rear leg tube.

Remove and discard protective foam sleeves from ends of axle. Insert axle into outside hole of brake assembly and slide it through frame.

Slide a rear wheel onto the axle then slide a washer onto the axle.

Fit straight part of cotter pin through hole on axle as shown.

Assemble other rear wheel to axle with washer and cotter pin.

Line up each of the 4 tabs of the hub cap with the 4 slots in the wheel and snap hub cap into place. Repeat for second side.

▲

★

To Assemble Front Wheels

Lay stroller back on handle.

Position front wheel assembly as shown.

NOTE: There is a LEFT and RIGHT front wheel assembly. Be sure to assemble them onto the correct leg tube.

• TRIANGLE = “▲” RIGHT

• STAR = ”★“ LEFT

Push front wheel assembly onto front leg tube until spring loaded button clicks into place.

NOTE: Make sure that spring loaded buttons pop through frame. If your spring loaded button becomes out of place, take pliers and feed button into hole. If spring loaded buttons DO NOT pop through, front wheel assembly could fall off during use.

Repeat for other side.

Align both sides of adjustable footrest mechanism with seat tube frame as shown.

Push adjustable footrest mechanism onto seat tube until spring loaded button clicks into place.

NOTE: Make sure that spring loaded buttons pop through frame. If your spring loaded button becomes out of place, take pliers and feed button into hole.

To Assemble Adjustable Footrest Mechansism to Seat

Spring Loaded Button

Push Together

2 & 3

Spring Loaded Buttons

▲

★

★▲

To Attach Front Tray

Release Button

CAUTION

To prevent injury to your child, take care when inserting tray into frame.

Align tray into holes located on seat frame.

Snap tab in place until a click is heard.

Repeat for second side.

TO ROTATE OR REMOVE TRAY: Push in release button located near side housing and pull tray out. Repeat on other side, to remove tray completely.

1 & 2

To Attach Seat

3 & 4

WARNING

DO NOT Place car seat in stroller seat. Car seat will not be secure.

Seat Housing Slot

Seat Post

Seat Lock Tab

Release Button

4 & 5

Place stroller upright with all 4 wheels on the ground.

Pick up seat by seat frame and place seat in either forward or reverse position.

Align posts with seat housing slots as shown.

Press seat down until a "click" is heard on both sides. Pull up on seat to make sure it is secured to stroller frame.

NOTE: You can tell if seat is locked in place by looking at square window on side of seat housing slot. If a red tab appears in that window, seat is locked.

To reverse seat, push in release buttons located on both sides of seat frame, lift up and reverse seat direction.

To Attach Canopy

To Attach Parent Cup Holder (select models)

Align cup holder hole with posts on handle and snap onto handle.

TO REMOVE, Hold cup holder and pull upward from the bottom. Cup holder is top rack dishwasher safe.

WARNING

DO NOT place more than 3 lbs. (1.36 kg) in this tray to avoid tipping!

Post

Insert canopy posts into slots onto seat frame as shown.

Infant neck roll is to be used with newborns who can not hold up their head. It should be used only when the seat is reclined. It can be removed when a child can hold their head up unassisted.

When using the infant neck roll, be sure that the shoulder restraint straps are fed through the holes on either side. Restraint must always be used with the infant neck roll.

To Install Infant Neck Roll

To Secure Child In Stroller

Lock both foot brakes to keep stroller from rolling.

Place child in stroller.

Hook shoulder straps to waist belt.

To fasten restraint system buckles push together. Be sure both buckles are fastened to secure child safely.

To unsnap restraint system buckles press tabs to release.

For proper fit, adjust shoulder straps and waist band as shown.

WARNING

Avoid serious injury from falling or sliding out. Always use restraint system. Do not use product without full 5-point Harness Restraint. Removing the shoulder straps will not adequately restrain child.

Adjust Restraint System Harness

How to Properly Use Your New Stroller

To Operate Brakes

Push levers on both rear wheels down to lock.

Pull levers up to unlock.

Unlock

Lock

NOTE: For a secure fit, straps should be at or below the child's shoulder. Adjust straps to higher position as your child grows.

To readjust shoulder restraints, turn the plastic toggle and thread through the slot from the back of the seat.

To position the shoulder strap to a higher position, push plastic toggle through top front slot as shown. Repeat for second side.

Make sure toggles are horizontal and flat against the back of the seat.

To Adjust Shoulder Strap Height

Lower Higher

To Install and Use Infant Car Seat Adapter

To use Infant Car Seat Adapter, first remove seat by pushing in release buttons located on side of seat frame and lift up.

Align posts of Infant Car Seat Adapter with seat housing slots.

Press Infant Car Seat Adapter down until a "click" is heard on both sides. Pull up on Infant Car Seat Adapter to make sure it is secured to stroller frame.

NOTE: Infant Car Seat Adapter is keyed so you can only assemble it one way. DO NOT force it. You can tell if Infant Car Seat Adapter is locked in place by looking at square window on side of seat housing slot. If a red tab appears in that window, Infant Car Seat Adapter is locked.

Rear Bar

Front Bar

Restraint Bag

Seat Housing Slots

Seat Lock Tab

Incorrect Assembly

To Recline Seat

To recline seat to desired position, adjust strap as shown.

WARNING

To avoid finger entrapment or pinching, do not adjust the seat back while child is in the stroller.

Footrest can be adjusted for child’s comfort. Push in side buttons to adjust.

To Adjust Footrest

Adjustment Strap

WARNING

To Secure All Acceptable Infant Car Seats

Remove restraint buckles from bag located on frame of stroller.

With one hand, grasp the Infant Car Seat handle (in its upright, carrying position). With your other hand, grasp Infant Car Seat near baby’s feet. Gently position the Infant Car Seat above

Infant Car Seat Adapter

so the baby faces the stroller handle.

Lower the Infant Car Seat between the front & rear bars.

Thread RED infant car seat restraint belts located in the side pocket through the clips on the top of the car seat. Tighten Restraint Straps.

Special Instructions

for Car Seats without belt slots: Secure Infant Car Seat to

Adapter

by wrapping restraint around frame and over seats lowest center point near handle and buckle them together. Tighten Restraint Straps.

NOTE: Shopping cart lever will not lock onto the carrier. To secure infant car seat to carrier, use restraint straps.

To Secure Infant Car Seat

Lock both foot brakes to keep stroller from rolling.

To fasten car seat restraint belts - open up loop of the restraint belt. Adjust belt until the buckles almost touch.

Pull end tab of restraint belt to set. Push buckles together to secure.

When using this product, to avoid serious injury from falling or sliding out, infant must always be secured in the Infant Car Seat with the Car Seat harness. Refer to Infant Car Seat Instructions for proper adjustment.

Continued on next page

1 & 2

Belt Slots

Lowest Center Point

3 & 5

To unsnap Restraint Belt - press tabs.

Make sure Infant Car Seat is secure. Test Infant Car Seat installation by moving it in all directions to ensure a tight fit to

Adapter

NOTE: Your Infant Car Seat may have a level indicator. It is not necessary for use with this carrier and the indicator may fall outside the recommended area. The level indicator is for use while the Infant Car Seat is in an automobile. Your childs head should always be above their knees.

To Remove Infant Car Seat

Unbuckle Restraint Belts and remove them from Car Seat belt slots.

With one hand grasp the Infant Car Seat carry handle (in its upright, carrying position).

To Fold Stroller

Lock brakes.

Put seat in the forward and upright position. DO NOT fold when seat faces handle.

Close canopy fully.

Adjust footrest to be in line with seat frame so stroller will stand in folded position.

To fold, pull up on both folding triggers at the same time.

Continued on next page

Lift handle up and over seat and rest it on lower frame.

Place one hand on side lock (A), and one on foam grip on cargo tube (B) as shown.

Pull up on cargo tube to fold.

Engage locking latch.

TO FOLD: While pushing seat away from frame, also push basket down. Rotate handle over frame until it locks into place. Push down on basket with foot to make sure frame is locked.

7 & 8

Care & Maintenance

• To keep your stroller running smoothly and avoid squeaking wheels use a silicon or graphite based lubricant. It is important to get it into the axle and the wheel assembly.

• Clean metal parts with a damp cloth and wipe dry.

• Clean woven fabric or vinyl parts with mild soap and water solution.

• Dry wet stroller with a soft cloth to prevent rusting.

• When storing stroller, never stack other items on top of it; this may damage the stroller.

• Periodically check for worn parts, loose screws, torn materials or stitching.

• Replace any damaged parts immediately.

+ 33 hidden pages