Kolcraft EQ800 User Manual

Page 1
Bella Bed Rails Assembly Instructions
Instructions d'assemblage des traverses pour lit Bella
Instrucciones de montaje de travesaños Bella
©2014 Made under license from Sealy Technology, LLC ©2014. Fabrication autorisée par Sealy Technology, S.A.R.L. www.sealybaby.com Manufactured for Kolcraft Enterprises, Inc. Fabriqué pour Kolcraft Enterprises, Inc.
Q023
Page 2
Parts:
Left Bed Rail
A
Right Bed Rail
B
Slat Roll
C
Allen Wrench
F
14 x Wood Screw
D
4 x Allen Screw, 3/4” Long
E
Headboard
(B) Right Bed Rail
(A) Left Bed Rail
Step 1:
A. Line up the screws in the Left and Right Bed Rails (A & B) with the holes in the headboard. Tighten the screws with the Allen wrench
Page 3
(B) Right Bed Rail
(A) Left Bed Rail
Lower Footboard
Step 2:
B. Line up the screws in the bed rails with the holes in the lower footboard and tighten securely with the Allen wrench.
Page 4
Slat Roll (C)
3/4” Allen screw (E)
Wood screw (D)
Step 3:
A. Unroll the slat roll and center it on the bed rails. Insert the Wood Screws (D) into the slats and tighten securely using a screwdriver. B. Insert the 3/4” Allen screws (E) in the visible holes in the headboard. Tighten securely.
CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR OTHER FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER FASTENERS. DO NOT USE IF ANY PARTS ARE MISSING, DAMAGED, OR BROKEN. CONTACT KOLCRAFT ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
Page 5
Pièces :
A
B
Traverse droite du lit
C
Banc de lit
F
Clé hexagonale
D
14 vis à bois Traverse gauche du lit
E
4 vis hexagonales de 19,1 mm (3/4 po) de long
Tête de lit
(B) Traverse droite du lit
(A) Traverse gauche du lit
Étape 1 :
A. Alignez les vis des traverses gauche et droite (A et B) avec les trous de la tête de lit. Serrez les vis avec la clé hexagonale.
Page 6
(B) Traverse droite du lit
(A) Traverse gauche du lit
Pied de lit inférieur
Étape 2 :
B. Alignez les vis des traverses du lit avec les trous du pied de lit inférieur et serrez fermement avec la clé hexagonale.
Page 7
Banc de lit (C)
Vis hexagonale de 19,1 mm (3/4 po) (E)
Vis à bois (D)
Étape 3 :
Déroulez le banc de lit et placez-le au centre des traverses.
A. Insérez les vis à bois (D) dans les banc de lit et vissez fermement avec un tournevis. B. Insérez les vis hexagonales de 19,1 mm (3/4 po) (E) dans les trous visibles de la tête de lit. Serrez fermement.
ASSUREZ-VOUS QUE LA QUINCAILLERIE EST INTACTE, QUE LES JOINTS SONT SERRÉS, QUE LES BOULONS ET AUTRES PIÈCES DE FIXATION SONT SERRÉS, QUE TOUTES LES PIÈCES SONT INSTALLÉES, QUE LES BORDS NE SONT PAS COUPANTS AVANT ET APRÈS L'ASSEMBLAGE ET PÉRIODIQUEMENT PENDANT L'UTILISATION DU LIT. SERREZ FERMEMENT TOUS LES BOULONS ET TOUTES LES PIÈCES DE FIXATION LÂCHES. N'UTILISEZ PAS LE LIT SI DES PIÈCES SONT MANQUANTES, ENDOMMAGÉES OU BRISÉES. COMMUNIQUEZ AVEC KOLCRAFT ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) POUR OBTENIR DES PIÈCES DE RECHANGE ET LES INSTRUCTIONS, LE CAS ÉCHÉANT. NE SUBSTITUEZ AUCUNE
Page 8
Partes:
A
B
Travesaño derecho
C
Rollo de listones
F
Llave Allen
D
Tornillos de madera, 14 unidades Travesaño izquierdo
E
Tornillos Allen de 3/4” de largo, 4 unidades
Cabecera
(B) Travesaño derecho
(A) Travesaño izquierdo
Paso 1:
A. Alinee los tornillos de los travesaños izquierdo y derecho (A y B) con los agujeros de la cabecera. Ajuste los tornillos con la llave Allen.
Page 9
(B) Travesaño derecho
(A) Travesaño izquierdo
Piecera inferior
Paso 2:
B. Alinee los tornillos de los travesaños con los agujeros de la piecera inferior y ajústelos bien con la llave Allen.
Page 10
Tornillo Allen de 3/4” (E)
Rollo de listones (C)
Tornillo de madera (D)
Paso 3:
A. Desenrolle los listones y céntrelos en los travesaños de la cama. Coloque los tornillos de madera (D) en los listones y ajústelos bien con un destornillador. B. Coloque los tornillos Allen de 3/4” (E) en los agujeros visibles de la cabecera. Ajústelos bien.
TANTO ANTES COMO DESPUÉS DE ARMAR EL PRODUCTO Y CON FRECUENCIA DURANTE EL USO, REVISE QUE NO HAYA ELEMENTOS DAÑADOS, CONEXIONES SUELTAS, PERNOS U OTROS SUJETADORES FLOJOS, PIEZAS FALTANTES O BORDES FILOSOS. AJUSTE CON FIRMEZA LOS PERNOS Y OTROS SUJETADORES FLOJOS. NO USE SI ALGUNA DE SUS PARTES FALTA, ESTÁ DAÑADA O ESTÁ ROTA. CONTÁCTESE CON KOLCRAFT ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) SI NECESITA PIEZAS DE REPUESTO U OTRAS INSTRUCCIONES IMPRESAS. NO SUSTITUYA PIEZAS.
Loading...