Bella Convertible Crib
Assembly Instructions
Instructions d'assemblage pour lit de
bébé transformable Bella
Instrucciones de montaje de la cuna
convertible Bella
©2014 Made under license from Sealy Technology, LLC ©2014. Fabrication
autorisée par Sealy Technology, S.A.R.L. www.sealybaby.com Manufactured for
Kolcraft Enterprises, Inc. Fabriqué pour Kolcraft Enterprises, Inc.
Q022
WARNING
FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
¢
¢NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CAN CAUSE SUFFOCATION.
¢TO REDUCE THE RISK OF SUDDEN INFANT DEATH SYNDROME (SIDS), PEDIATRICIANS
RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR BACKS TO SLEEP, UNLESS OTHERWISE
ADVISED BY YOUR PHYSICIAN.
¢INFANTS CAN SUFFOCATE ON SOFT BEDDING. NEVER ADD A PILLOW OR COMFORTER.
NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.
STRANGULATION HAZARD
¢STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER
A CRIB OR ATTACH STRINGS TO TOYS.
¢TO HELP PREVENT STRANGULATION, TIGHTEN ALL FASTENERS. A CHILD CAN TRAP PARTS
OF THE BODY OR CLOTHING ON LOOSE FASTENERS.
¢DO NOT PLACE CRIB NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
FALL HAZARD
¢WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE
AS STEPS FOR CLIMBING OUT.
¢STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF
35 IN. (89 CM).
¢CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR OTHER
FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND
FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER FASTENERS. DO NOT
USE CRIB IF ANY PARTS ARE MISSING, DAMAGED, OR BROKEN. CONTACT KOLCRAFT
ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) FOR REPLACEMENT
PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
¢IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
¢FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB.
¢INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS TOO
SMALL.
¢ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 IN. (69 CM) BY 51-5/8 IN. (131
CM), WITH A THICKNESS NOT EXCEEDING 6 IN. (15 CM). THE DIMENSIONS OF THE MATTRESS
SHOULD BE TAKEN FROM SEAM TO SEAM.
¢PREVENT BURNS. KEEP CRIB AWAY FROM OPEN FIRES AND OTHER HEAT SOURCES.
Crib Parts:
A
Headboard
D
2x Crib Side
B
Upper Footboard
C
Lower Footboard
Left Day Bed Cap Right Day Bed Cap
E
F
Mattress Support
G
H
Allen Wrench
(A) Headboard
Mattress support holes
should face the inside of
the crib
Thread and tighten three
screws (both sides)
(D) Crib Side
(D) Crib Side
Step 1:
A. Line up the Crib Sides (D) with the Headboard (A). The mattress support holes on the crib
sides should be facing the inside of the crib.
B. Align the screws with the holes in the headboard and tighten with the allen wrench. Repeat
for the other side.
Thread and tighten
all four screws
High Position
Middle Position
Low Position
(G) Mattress Support
Label reading “This Side Up” should be
facing up
Mattress support arms should be
above the mattress support
Step 2:
A. Flip the mattress support so the “This Side Up” label is facing up. If the label is missing, the
correct orientation is with the springs at the top of the frame. The mattress support arms
should be above the mattress support.
B. With a helper to hold it at the right height, align the screws on the Mattress Support (G)
with the holes on the crib sides and tighten with the allen wrench. There are three possible
height positions. The support should start at the high position for newborns, then be moved
lower as the child grows and becomes more mobile. Once the child is able to pull up to a
(B) Upper Footboard
Thread and tighten all
( C) Lower Footboard
Step 3:
A. Place the Lower Footboard (C) against the crib sides.
B. Turn the two bottom screws into the lower footboard holes, but don’t tighten them yet.
C. Place the Upper Footboard (B) on top of the lower footboard.
D. Turn the two upper screws into the upper footboard holes, but don’t tighten them all the
way yet. Repeat for the other side.
E. Once all the screws are started, tighten them all with the allen wrench.