Kohler Mira Jump 7.5, Mira Jump 10.8, Mira Jump 8.5, Mira Sprint 8.5, Mira Sprint 9.5 Installation And User Manual

These instructions must be left with the user

Installation Guide

Mira Jump

7.5, 8.5, 9.5 and 10.8 kW Electric Shower

1224546-W2-D

For SPARES, ADVICE

or REPAIRS

Please call us on

0844 571 5000

(UK Only)

Mira Sprint

8.5, 9.5 and 10.8 kW Electric Shower

COMMISSIONING

SERVICING

© Kohler Mira Limited, May 2017

Mira is a registered trade mark of

Kohler Mira Limited.

The company reserves the right to alter

product specications without notice.

FM 14648

CUSTOMER SERVICE

The guarantee applies solely to the original installation under normal
use and to the original purchaser only. The product must be installed
and maintained in accordance with the instructions given in this guide.

Servicing must only be undertaken by us or our appointed representative.
Note! If a service visit is required the product must be fully installed and
connected to services.

Repair under this guarantee does not extend the original expiry date.
The guarantee on any replacement parts or product ends at the original
expiry date

For shower ttings or consumable items we reserve the right to supply

replacement parts only.

The guarantee does not cover:

Call out charges for non product faults (such as damage or performance
issues arising from incorrect installation, improper use, inappropriate
cleaning, lack of maintenance, build up of limescale, frost damage,

chemical attack, corrosion, system debris or blocked lters) or where no

fault has been found with the product.

Water or electrical supply, waste and isolation issues.

Compensation for loss of use of the product or consequential or indirect
loss of any kind.

Damage or defects caused if the product is repaired or modied by persons

not authorised by us or our appointed representative.

Accidental or wilful damage

Products purchased ex-showroom display.

What to do if something goes wrong

If your product does not work correctly refer to this manual for fault diagnosis
and check that it is installed and commissioned in accordance with our
instructions.
If this does not resolve the issue, contact us for help and advice.

Extended Guarantees

A selection of protection plans are available that enable you to cover repair

bills (excludes Eire). Ring 01922 471763 for more details.

Guarantee

Your product has the benet of our manufacture’s guarantee which starts from

date of purchase. This guarantee only applies in the United Kingdom and
Republic of Ireland. To activate this guarantee, please return your completed

registration card, visit our website or free phone [phone] within 30 days
of purchase (UK only).

Within the guarantee period we will resolve defects in materials or
workmanship, free of charge, by repairing or replacing parts or product as
we may choose.

This guarantee is in addition to your statutory rights and is subject to
the following conditions:

Helpdesk Service - Contact our Customer Services Team for

product advice, to purchase spare parts or accessories or to set
up service visit. You can contact us via phone or e-mail - contact
details below. Please provide your model name, power rating (if

applicable) and date of purchase.

Mira Showers Website (www.mirashowers.co.uk)

Visit our website to register your guarantee, download user
guides, diagnose faults, purchase our full range of accessories
and popular spares, or request a service visit.

Spares and Accessories - We hold the largest stocks of genuine
Mira spares and accessories. Contact us for a price or visit our
website to purchase items from our accessory range and popular

spares. (Only available in the United Kingdom).

Service/Repairs - No one knows our products better than our
nationwide team of Service Technicians. We can carry out service
or repair work to your product both during and after the guarantee
period (Only available in the United Kingdom and Republic of

Ireland). Ask about our xed price service repairs.

To Contact Us

0844 571 5000

Fax: [phone]

E-mail:

www.mirashowers.co.uk/contactus

Mira Customer Services Dept

Cromwell Road, Cheltenham,

Gloucestershire

GL52 5EP

To Contact Us: Eire Only

01 531 9337

E-mail:

[e-mail]

WARNING
There are no user serviceable parts inside the shower.

Servicing of the shower must only be carried out by qualied,

competent personnel following the instructions provided in this
guide and those provided with any spare part.

Before replacing any parts, ensure that the underlying cause of

the malfunction has been resolved.

Cleaning the Inlet Filter

Warning! Isolate the electrical and water supplies before removing

the cover.
Remove the cover.

Remove the elbow from the
inlet connector.

Note! Depending on your
installation it may be necessary
to remove the shower from the

wall to allow lter removal.

In this case isolate all supplies
and follow steps 6 - 8 in reverse
order as detailed in section:
‘INSTALLATION’.

Inlet Filter

Inlet
Connector

Prise the lter from the inlet

connector assembly.

Rinse the lter under a

running tap to remove
any lodged particles. If
necessary, use a kettle
descalent in accordance

with the manufacturer’s
instructions. Ret the inlet
lter and follow steps 7 and 10

as described in section: ‘INSTALLATION’.

Note! If the shower was removed from the wall, steps

6, 7, 8 and 10 will need to be followed as described in section:

‘INSTALLATION’.

Follow the steps detailed in section: ‘COMMISSIONING’ to prepare
the shower for use.

No water or very

low ow rate

The heater tank is
excessively scaled

Replace the heater
tank assembly

The inlet lter is

blocked

Clean the inlet lter

The fuse is blown
or the MCB / RCD has
been tripped, indicating
a possible electrical
fault; for example,
heater tank element
failure

Switch on the power at
the double pole switch

The on / off switching
assembly is faulty

Replace on / off switching
assembly

The start / stop switch
is faulty

Replace start / stop switch

The solenoid coil is
faulty

Replace solenoid coil

Water leaks from
the bottom of the
case near the
outlet and there is

no ow from the

showerhead

The pressure relief
valve in the tank has
been triggered (usually
due to a blocked

outlet), when the relief

valve operates a small
rubber ball is ejected

Resolve the blocked
outlet and replace the
heater tank assembly

The water cannot
be turned off

The on / off switching
assembly is faulty

Replace on / off switching
assembly

The start / stop switch
is faulty

Replace start / stop switch

The supply pressure
is below the minimum
required

Check the static water
pressure. Note that the
static water pressure may
fall below the minimum
requirement when other
appliances are drawing
water, for example the
dishwasher or the washing
machine

Adjust temperature as required.
Note! Flow rate will reduce
when temperature setting is
increased.

Temperature will rise further.

Turn power control to High.Temperature will rise slightly.

5 - 10 secs

COLD

HOT

109

5 - 10 secs

COLD

HOT

7 8

Water ows freely within a few

seconds, temperature remains
cool

Turn power control to Eco.

COLD

0 - 15 secs

HOT

Push START/STOP button.Switch on the electrical supply.

5 6

4

3

1 2

Turn temperature control to the
cold position.

Turn power control to low.

Use the terminal block location
that is most appropriate for
your installation i.e. If the
electric supply is on the right
hand side then use the right
hand terminal block.
Strip back sufficient outer
cable insulation to enable
routing to the terminal block.

Fit an earth sleeve to the
earth wire.
Insert the wires into the
terminal block.

Tighten the screws in the
terminal block, ensure the
wires are secure and tight.

For falling or rising supplies
the cover has thinned sections
on the top and bottom that can
be removed to allow entry of
the supply pipe and electrical
cables.

Cover

Screw

Screws

Thinned
Section

Ensure the earth bonding complies with relevant regulations.

L (Live) = Brown wire

(Protective Earth) = Green /Yellow sleeved wire

N (Neutral) = Blue wire

8

Ensure the control dials are
aligned with the spindles and
replace the cover.

Tighten the three cover
screws.

Do not use alternative screws
to secure the cover. This can
cause internal damage to the
appliance.

Do not seal around the back of appliance.

Install the shower ttings (Refer to the Shower Fittings
Installation and User Guide packed with the product).

The shower must be commissioned before use, please
refer to section: ‘COMMISSIONING’.

This completes the installation.

9

10

11

12

13

Terminal

Block (LH)

Terminal

Block (RH)

Warning! There are no user serviceable components beneath the

cover of the appliance. In the event of a malfunction of the shower,
the troubleshooting information below provides details on possible

causes and remedies that may be carried out by qualied, competent
personnel. Non-qualied personnel should refer to the fault diagnosis

section in the users guide.

FAULT DIAGNOSIS

Symptom Possible Cause Possible Remedy

No hot water from
the shower, with
the controls in
ECO/HIGH
position

Insufcient water

supply pressure

Contact local water
authority

Failure of the
microswitch or thermal
switch

Check the continuity
of the switches, using
a suitable continuity
measuring device.
Replace the switches as
necessary

An internal wiring
connection has failed

Check the integrity of the
internal wiring

One of the heater tank
elements has failed

Replace the heater tank
assembly

Switch assembly fault Replace On / Off switching

assembly

The shower
temperature
cycles between
hot and cold with
power control in
ECO/HIGH

The hose or
showerhead is
blocked

De-scale showerhead,
check hose for kinks or
damage and replace if
necessary. Refer to the
User Maintenance section
of the user guide

The temperature is
set too high. This is
causing the thermal
switch to turn off the
heating element to
reduce the water
temperature

Turn the temperature
control anticlockwise
to reduce the water
temperature or turn the
power control to ECO.
DO NOT TAMPER with
the thermal switch

Turning the
temperature
control does not
affect the water
temperature

The ow regulator is

faulty

Replace the heater tank
assembly

The hose or
showerhead is
blocked

De-scale showerhead,
check hose for kinks or
damage and replace if
necessary. Refer to the
User Maintenance section
of the user guide

No water or very

low ow rate

The hose or
showerhead is
blocked

De-scale showerhead,
check hose for kinks or
damage and replace if
necessary. Refer to the
User Maintenance section
of the user guide

The incoming water
supply stop valves, or
the appliance isolating
valve is closed

Open the stop/isolating
valve completely

Insufcient water

supply pressure

Contact the local water
authority

Power LED does
not illuminate
when the pull cord
is operated

Electrical supply failure

(MCB, pull cord etc.)

Check electrical supply

Power LED faulty Replace the wiring loom

Note! A slight hissing sound may be heard from the shower
during operation. High mains water pressure and high shower
temperatures will affect the tone. This is quite normal in use.

A small amount of water may
continue to drain over a few
minutes.

13

11 12

Switch off the electrical supply.Push START/STOP button.

WIRING DIAGRAM

ACCESSORIES

Genuine Mira accessories can be purchased direct from Customers
Services (our contact details can be found on the back cover of this

guide) or from approved stockists or merchants.

Inlet Pipe Accessory

1788.443

Designed to simplify the

retrotting of a Mira shower

onto existing pipework. Note!
Some adjustment of pipe
length may be necessary.

SPARE PARTS

1693.331 Component Pack (Not illustrated)

1788.436 Screw Pack (Not illustrated)

1788.424

Mira Jump Cover Assembly

1788.425

Mira Sprint Cover Assembly

1788.439

Outlet
Connector

1789.085

Latching
Switch

1788.437

Terminal Block
Assembly

1788.435

Inlet Filter

1788.434

Solenoid Coil

1788.429

On / Off Switching
Assembly

1746.436

Thermal
Switch

1788.433

Valve Clamp

NE L

MICROSWITCH

(LEFT)

MICROSWITCH

(RIGHT)

BLUE

GREY

BLUE

BROWN

BROWN

BROWN

GREEN

RED

RED

BROWN

BROWN

BLUE

BLUE

GREEN

BLUE

BROWN

BLUE

RED

NE L

GREEN

BROWN

BLUE

BLUE

TERMINAL

BLOCK

TERMINAL

BLOCK

LED

START /

STOP

SOLENOID

HEATER

TANK

1788.438

Earth Terminal
Block Assembly

1788.440

Wire Loom
and LED

1788.478 (7.5kW)

1788.426 (8.5kW)

1788.427 (9.5kW)

1788.428 (10.8kW)

Heater Tank
Assembly
(includes

microswitches)

Plumbing Variant

7.5 8.5 9.5 10.8

Min Dynamic Pressure 70 kPa

(0.7 bar)

70 kPa

(0.7 bar)

70 kPa

(0.7 bar)

100 kPa

(1.0 bar)

Max Dynamic Pressure 500 kPa (5.0 bar)

Max Static Pressure 1000 kPa (10 bar)

Min Static Pressure 50 kPa (0.5 bar)

Max Inlet Temperature 30°C

Min Inlet Temperature 2°C

Inlet Connection 15 mm Compression / Pusht Coupling

Max Water Hardness 200 ppm CaCO

3

Outlet Connection 1/2” BSP Male

Electrical Variant

7.5 8.5 9.5 10.8

Nominal Power at 240 V ac 7.5 kW 8.5 kW 9.5 kW 10.8 kW

Nominal Power at 230 V ac 6.9 kW 7.8 kW 8.7 kW 9.9 kW

Recommended MCB Rating 32 A 40 A 40A 45 A

Max Supply Cable Size 16 mm²

Recommended RCD Rating 30 mA tripping current

Recommended Isolator
Switch

45 A double-pole with 3 mm contact

separation

Appliance Sealing Rating IP X4 - Suitable for installation in Zone 1

Max Ambient Temperature 30°C

Min Ambient Temperature 2°C

European Conformity Information

This range of electric showers complies with the following European
directives:
2006/95/EC Low Voltage Directive, 2004/108/EC EMC Directive,

2011/65/EU RoHS Directive

This range of electric showers are high power appliances and are
subject to conditional connection. If the main electrical supply fuse is
rated less than 80 Amps, the local electricity supply company must be

contacted to conrm if the electrical supply is adequate.
This range of showers complies with the requirements of the UK’s

water regulations.

Dimensions

Height 356 mm

Width 225 mm

Depth 107 mm

‘Snap Off’
section for
rear entry

Terminal

Block (LH)

INTRODUCTION

SPECIFICATION

Documentation

1 x Electric Shower

 1 x Installation Guide

 1 x User Guide

 1 x Guarantee Brochure

PACK CONTENTS

INSTALLATION REQUIREMENTS

 1 x Installation Template (printed on

the inside of product carton)

1 x Component Pack

1x Showerhead

1x Hose

1 x Shower Fittings

PLUMBING

1. The plumbing installation must comply with all national or local
water regulations and all relevant building regulations, or any

particular regulation or practice specied by the local water

supply company.

2. Do not install the product in a position in which service access
is limited.

3. Decide on a suitable position for the shower (minimum distance
of 200 mm from the ceiling to allow for cover t and removal).

4. The shower is suitable for installation within the shower area

and is tted with a pressure relief valve. It must be positioned

over a water catchment area with the controls at a convenient
height for the user.

5. The shower must be tted to a waterproof at and even wall

surface.

6. DO NOT t the shower to the wall and tile up to the case.

7. DO NOT seal the gap between the shower and the wall surface.

8. The showerhead should be positioned so that it discharges down
the centre line of the bath or across the opening of a shower
cubicle.

9. The showerhead must be directed away from the shower unit,
during normal use the showerhead must not spray directly on
to the shower unit.

10. DO NOT apply excessive force to plumbing connections;
always provide mechanical support when making plumbing
connections. Any soldered joints should be made before
connecting the shower.

11. The position of the shower and shower ttings must provide a

minimum gap of 25 mm between the showerhead and the spill
over level of any bath, shower tray or basin and a minimum

gap of 30 mm between the showerhead and the spill over level

of any toilet, bidet or other appliance with a Fluid Category 5

backow risk.

Note! There will be occasions when the hose retaining ring will

not provide a suitable solution for Fluid Category 3 installations, in
these instances an outlet double checkvalve must be tted, this will
increase the required supply pressure typically by 10kPa (0.1 bar).
Double checkvalves tted in the inlet supply to the appliance cause

a pressure build up, which affect the maximum static inlet pressure

for the appliance and must not be tted. For Fluid category 5 double

checkvalves are not suitable.

Zone of

Backow Risk

30 mm

Minimum

Toilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Electric
Shower

25 mm

Minimum

25 mm Minimum

Hose retaining ring tted and shower ttings xed at a suitable
height preventing dirty water backow.

12. This shower is not designed to be plumbed directly from the
rear. For rear-entry supply, add an elbow to the supply pipe and
connect as a rising or a falling supply.

13. If pipework and/or electrical cables enter the shower from the

rear through a hole in the wall provision must be made to prevent
water ingress back into the wall structure.

14. This shower is intended to be permanently connected to the
mains water supply, only use the inlet connection supplied with
the shower.

DO NOT use any other type of tting.

15. A full bore/non restrictive servicing valve must be tted in a

readily accessible position adjacent to the shower to facilitate
maintenance of the shower. DO NOT use a valve with a loose

washer plate (jumper) as this can lead to a build up of static

pressure.

16. A water treatment device should be installed where the water
hardness may exceed 200 ppm. Malfunctions caused by

excessive limescale formation are not covered by this shower’s
guarantee (see back page for details).

17. The installation must not cause the hose to be sharply kinked
during normal use.

18. DO NOT perform the electrical installation until the plumbing
has been completed and checked for leaks.

ELECTRICAL

1. The electrical installation must comply with BS 7671 (commonly

referred to as the IEE Wiring Regulations) and all relevant

building regulations, or any particular regulation or practice

specied by the local electricity supply company.

2. Ensure that all circuit protection devices, switches and cabling is
adequate for the rated current of the shower and that the rating
of the electricity supply company fuse and the consumer unit
are adequate for the additional demand.

3. The shower must be earthed. Ensure any supplementary
bonding complies with the relevant regulations.

4. This shower is intended to be permanently connected to the

xed electrical wiring of the mains system. A separate supply

must be provided from the consumer unit to the shower.

5. DO NOT supply any other electrical equipment including
extractor fans or pumps via this product.

6. This shower must be provided with means for local disconnection

that is incorporated into the xed wiring in accordance with the

relevant local wiring regulations. This must be a double pole

switch, which has at least 3 mm contact separation in each pole.

The switch can be a ceiling mounted pull-cord type within the

shower room or a wall mounted switch tted in the applicable

zone area.

7. For new installations a 30mA Residual Current Device (RCD)

must be incorporated into the electrical supply to this shower
in accordance with current wiring regulations. When replacing

an existing electric shower we recommend that a 30mA RCD

be incorporated in accordance with current wiring regulations
if not already provided

8. DO NOT apply excessive force to the terminal block.

9. All electrical connections should be checked for tightness to
prevent overheating before switching on the electrical supply.

Inlet
Supply

Pusht

Elbow

Inlet
Connector

8

9

Thank you for choosing a Mira shower. To enjoy the full potential of
your new shower, please take time to read this guide thoroughly, and
keep it handy for future reference.
Products manufactured by Kohler Mira Ltd are designed to be safe,
provided that they are installed, used and maintained in good working
order, in accordance with our instructions and recommendations.
Follow all warnings, cautions and instructions contained in this guide,
and on, or inside the shower. This guide is also available in electronic
format on our website or by contacting customer services.
This product has separate controls for power selection and for

temperature/ow adjustment. A unique ow regulator stabilises any
temperature changes caused by water pressure uctuations, which
can result from taps being turned on or off or toilets being ushed.

Electrical and electronic devices contain a range of
materials that can be separated for recycling and used in
new products.

This shower should not be disposed of with your general household
waste. When this shower has reached the end of its serviceable life
please take it to a recognised WEEE (Waste Electrical and Electronic

Equipment) collection facility such as your local civic amenity site

for recycling.

Your local authority or retailer will be able to advise you of your
nearest collection facility.

Mira Electric Showers covered by this guide:

Product kW Model Number Colour

Mira Jump

7.5 J08 Hb

White / Chrome

8.5 J08 Db

9.5 J08 Eb

10.8 J08 Fb

Mira Sprint

8.5 J08 Da

9.5 J08 Ea

10.8 J08 Fa

Guarantee

This product has been designed for domestic use only, Mira Showers
guarantee this product against any defect in materials or workmanship

for a period of two years from the date of purchase (shower ttings
for one year).

For terms and conditions, refer to the back cover of this guide.

Domestic



Light Commercial



Heavy Commercial



Healthcare



Recommended Usage

IMPORTANT SAFETY INFORMATION

WARNING – This shower can deliver scalding temperatures,
cause re, electric shock or other personal injury if not installed,
operated or maintained in accordance with the instructions,

warnings and cautions contained in this guide and on or inside
the appliance.

Please read the important safety information and the installation
requirements detailed in this guide before installing the shower.
Failure to follow the instructions provided with this shower will
invalidate the guarantee.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. Installation of this shower must be carried out in accordance

with these instructions by qualied, competent personnel.

2. Isolate the electrical and water supplies before commencing
installation. The electricity must be isolated at the consumer unit
and the appropriate circuit fuse removed, if applicable. Mains
connections are exposed when the cover is removed.

3. DO NOT install the shower in areas with high humidity and
temperature (i.e. steam rooms and saunas).

4. DO NOT install the shower where it may be exposed to freezing
conditions. Ensure that any pipework that could become frozen
is properly insulated.

5. DO NOT switch the shower on if there is a possibility that the
water in the shower is frozen.

6. DO NOT switch the shower on if water starts leaking from
the shower case. Isolate the electrical supply to the shower
immediately.

7. DO NOT connect the outlet of the shower to any tap, control
valve, trigger operated handset or showerhead other than
that specified for use with this shower. Only Kohler Mira
recommended accessories should be used.

8. The water supplies to this product must be isolated if the product
is not to be used for a long period of time. If the product or
pipework is at risk of freezing during this period they should
also be drained of water.

9. DO NOT perform any unspecied modications, or drill or cut
holes in the product other than as instructed by this guide. When
servicing only use genuine Kohler Mira replacement parts.

10. If the shower is dismantled during installation or servicing then
upon completion the product must be inspected to ensure all
electrical connections are tight and that there are no leaks.

11. Read all installation instructions before installing this shower.

12. Upon completion of the installation, make sure that the user is
familiar with the operation of the shower, and leave this guide
and the user guide with the owner.

7

Connect the inlet supply pipe
to the inlet connector using a

push t elbow or an elbow with

compression nuts and olives.

Important! Do Not use pusht

elbows that require specialist
tools for removal. Access

to the inlet lter is required

periodically and so any
connector needs to be easily
removed for maintenance.

Note! When making
connections to the shower.
Do not use jointing paste
products as damage to the
shower will occur.

Turn on the water supply and
check connection for leaks.

L (Live) = Brown wire

(Protective Earth) =

Green / Yellow sleeved wire

N (Neutral) = Blue wire

For falling or rising supplies
the cover has thinned sections
on the top and bottom that can
be removed to allow entry of
the supply pipe and electrical
cables.

Ensure the control dials are
aligned with the spindles and
replace the cover.

Tighten the three cover
screws.

Do not use alternative screws
to secure the cover. This can
cause internal damage to the
appliance.

Do not seal around the back of appliance.

Install the shower ttings (Refer to the Shower Fittings
Installation and User Guide packed with the product).

11

Replacing an Existing Electric Shower

This electric shower can replace showers of approximate size and
shape.
Terminal Blocks are provided on both the left and right for convenience
when replacing a shower.
If the water entry point is on the right hand side of the shower then
you will need to alter the incoming pipework as shown below. The
Mira Inlet Pipe Accessory can be used to simplify this process. Refer
to section: ‘ACCESSORIES’.

Warning! Isolate the electrical and water supplies.

From the new shower, remove
the three screws that hold the
cover on then remove the cover.

Existing
pipework
locations

Disconnect and remove the old shower from the wall.

1

‘Snap Off’ case sections

are provided for ease of
installation when using
existing right side, rear entry
pipework.

Cover

Screw

Screws

10

Cover

Screw

Screws

2

Thinned
Section

Terminal

Block (RH)

Terminal

Block (LH)

Terminal

Block (RH)

Terminal Blocks are provided
on both the left and right for
convenience. Use the terminal
block location that is most
appropriate for your installation
i.e. If the electric supply is on the
right hand side then use the right
hand terminal block.

Strip back sufcient outer cable

insulation to enable routing to the
terminal block.

Fit an earth sleeve to the earth
wire.

Insert the wires into the terminal
block.

Tighten the screws in the terminal
block, ensure the wires are
secure and tight.

Ensure the earth

bonding complies with

relevant regulations.

INSTALLATION

Fitting a New Shower

Plumbing and Electrical Schematic

Cover

Screw

Screws

2

1

Falling

(entering the shower

from the top).

Rising

(entering the shower

from the bottom).

Remove the three screws
that hold the cover on and
remove the cover.

Use the Installation Template provided (printed on the product

carton), together with a spirit level to mark the positions of

the three xing holes.
Note! The shower should be positioned at least 200 mm from

the ceiling. Ensure that there are sufcient lengths of supply

pipe and electrical cable to reach the connection points as
shown on the template.

Drill three holes to suit the xing screws and wall plugs.

Caution! Do not drill into cables or pipes in the wall.

4

Determine the direction and route of the incoming water
supply:

Note! - DO NOT use an incoming supply entering the shower
directly from the back. Add an elbow to the supply pipe and
connect it as a rising or falling supply.

5

6

Secure the shower to the wall with xing screws and wall
plugs (supplied) or appropriate wall xings for your installation.

Thoroughly ush the supply pipe.

3

10. DO NOT switch on the electrical supply until the plumbing has
been completed and checked for leaks.

Warning! Isolate the electrical and water supplies before
installing the shower.

Place the shower on the wall where the previous shower was
installed and mark the positions of the three xing holes.

Note! Ensure that there are sufcient lengths of supply pipe

and electrical cable to reach the connection points.

3

Remove the shower and drill three holes to suit the xing

screws and wall plugs.

Caution! Do not drill into cables or pipes in the wall.

4

Thoroughly flush the
supply pipe.

5

Secure the shower to the

wall with xing screws and
wall plugs (supplied) or
appropriate wall xings for

your installation.

6

Connect the inlet supply
pipe to the inlet connector

using a push t elbow or

an elbow with compression
nuts and olives.

Turn on the water supply
and check connection for
leaks.

7

12

13

The shower must be commissioned before use, please
refer to section: ‘COMMISSIONING’.

This completes the installation.