Kohler MINIMA K-45803T-L-SHP, MINIMA K-45806T-L-SHP Installation Instructions Manual

BEFORE YOU BEGINBEFORE YOU BEGIN

MINIMA

INSTALLATION INSTRUCTIONS

SLIDING, 1 DOOR 1 PANEL

8mm K-45803T-L-SHP

10mm K-45806T-L-SHP

·

Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product

·

information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,

·

and warranty information-

instructions for the consumer.

Make sure that the bath and the finished wall

·

material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and

·

identify all the parts. Use the exploded view
illustrated on page 2 for reference.
For the installation method of customized shower

·

with different dimensions, please refer to this
instructions.

CAUTION: Risk of injury or product damage.

Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.

ATTENTION:

receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.

IMPORTANT:

finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.

Please install this door on Kohler

The shower door requires a flat vertical

please leave these

·

·

·

·

·

2

·

(

) 80mm

3mm/m

1198141-T01-B

-1-

13-1 528437

, 2014

Copyright Kohler China Ltd., 2014

ROUGHING-IN

H

B

PARTS IDENTIFICATIONPARTS IDENTIFICATION

IMPORTANT

Unit: mm

SKU B H

K-45803T
K-45806T

1200-1600 1850-2000

Before installation check that all components are
correctly supplied.

If any parts are missing please ring the helpline.

800-820-2628

Top Lintel

Inline Panel

Wall Channel

C

Glass Clamp

800-820-2628

Door Panel

1198141-T01-B

Threshold

Splashguard

-2-

Wall Channel

Cover Seal

4mm Allen key
4mm

Top Roller Clamps

Mid-support Clamp

X6

A

B

2.5mm Allen Key

2.5mm

X4

C

Screw Covers

X7

Screw Covers

X4

Support Strip

X2

X2

Bottom Guide

End Socket

Door Closing Guide

Plastic Guides

Frame Cap,LH Frame Cap,RH

X4

Wall Plugs

X7

X2

Wedge

ED

Handle

1198141-T01-B

-3-

INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS

Tools Required

·

Phillips Screwdriver

·

Pencil

·

Caulk Gun

·

Measuring Tape

·

Safety Glasses

·

Center Punch

·

Hammer

·

Knife

·

Masonry Drill & 6mm Drilll Bit

·

Level

Materials Required

·

Drop Cloth
Tape

·

Silicone Sealant

·

INSTALLATION

Fit tray and then tile walls before fitting
the unit.

·

·

·

·

·

·

·

·

·

·

·

·

·

NOTE: Glass seal will
extend out of wall
channel.

A

6mm

Fit Wall Channel 'A'

A

1

X3

6mm

X3

2

0mm

Tray MUST be level in all planes or the
unit will not install properly.

STEP

3

X3

0mm

4

Wall channels

MUST

plumb.

be

A

X3

5

STEP

1

Ensure the support strips are still on the bottom edge
of the inline panel, inside the H section, and that the H
section is 53mm from the corner of the glass.

2

1198141-T01-B

53mm

53mm

STEP

3

-4-