Kohler KT3134MBV User Manual

FINIAL®TRADITIONAL

Features

Brass construction

•

Traditional handle

•

Available with contrasting or matching ﬁnish faceplate

•

and handle accents Intended for use with Rite-Temp

•

Rite-Temp

valves

or HiFlow

Codes/Standards Applicable

Speciﬁed model meets or exceeds the following:

ASME A112.18.1/CSA B125.1

•

ASSE 1016

•

Speciﬁed Model

SHOWER FAUCET TRIM

K-T313

ALSO K-T309

Colors/Finishes

CP: Polished Chrome

•

PB: Vibrant®Polished Brass

•

Other: Refer to Price Book for additional colors/ﬁnishes

•

Model Description Colors/Finishes

K-T313-4F Shower only trim with biscuit accents ❑ CP ❑ PB K-T313-4M Shower only trim with polished ﬁnish accents ❑ CP ❑ PB ❑ Other____ K-T313-4P Shower only trim with white accents ❑ CP ❑ PB K-T309-4F Valve only trim with biscuit accents ❑ CP ❑ PB K-T309-4M Valve only trim with polished ﬁnish accents ❑ CP ❑ PB ❑ Other____ K-T309-4P Valve only trim with white accents ❑ CP ❑ PB

Required Accessories

K-304-* Rite-Temp®valve without stops OR ❑ NA K-2971-KS HiFlow Rite-Temp valve with stops ❑ NA * For a complete listing of all the RiteTemp valves, refer to the K-304-* Speciﬁcation Sheet or Roughing-In Sheet.

Product Speciﬁcation

The Rite-Temp pressure-balancing single-control shower faucet trim shall be made of brass construction. Shower only trim shall include showerhead with arm, and faceplate with traditional handle. Valve only trim shall include faceplate with traditional handle. Faucet trim shall be Kohler Model K-T_____-_____-_____ and Rite-Temp valve shall be K-304-_____-NA OR K-2971-KS-NA HiFlow Rite-Temp valve.

Page 1 of 2 1023659-4-

USA/Canada: 1-800-4KOHLER

(1-800-456-4537)

www.kohler.com

FINIAL®TRADITIONAL

Optional Accessories

88526 HiFlow Rite-Temp

Installation Notes

Install this product according to the installation guide. NOTICE: Risk of product damage. Long screws, for

installing trim, can damage the K-2971-KS valve. Consult the trim installation guide to verify if the thin wall installation kit (88526) is needed.

Avoid cross-ﬂow conditions. Do not install shut-off device on either valve outlet.

Cap shower outlet if deck-mount spout, diverter, or handshower is connected to spout outlet.

Install straight pipe or tube drop of 7″ (17.8 cm) to 18″ (45.7 cm) with single elbow between valve and wall-mount spout

thin wall installation kit ❑ CP ❑ PB ❑ Other____

1/2"-14 NPT

9" (22.9 cm)

13/16" (2.1 cm)

3-13/16" (9.7 cm)

2-3/4" (7 cm)

72" (182.9 cm) to 78" (198.1 cm) Floor (typical)

6-1/4" (15.9 cm) D.

48" (121.9 cm) to Floor (Shower Only)

Product Diagram

FINIAL®TRADITIONAL SHOWER FAUCET TRIM Page2of2

1023659-4-