Kohler K1146HK96 User Manual
PROFLEX®6040
Features
Acrylic
•
Oval shape
•
Drop-in
•
6 individually adjustable ProFlex
•
Pump with air switch and grounding-type plug-in cord
•
In-line heater
•
Molded lumbar supports and armrests
•
Optional K-9696 whirlpool trim kit in various finishes
•
Custom pump locations
•
60″ (1524 mm) x 40″ (1016 mm) x 17-5/8″ (448 mm)
•
hydro-massage jets
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
ANSI Z124.1.2
•
ASME A112.19.7
•
UL 1795
•
ASTM E162
•
ASTM E662
•
Specified Model
CUSTOM BATH WHIRLPOOL WITH
HEATER
K-1146-HK
ALSO K-1146-HN
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1146-HK Custom bath whirlpool with heater – drop-in (top view shown) ❑ 0 ❑ Other_____
K-1146-HN Custom bath whirlpool with heater – drop-in ❑ 0 ❑ Other_____
Recommended Accessories
K-7213 Clearflo bath cable drain with PVC tubing ❑ CP ❑ Other_____
K-7214 Clearflo bath cable drain without PVC tubing ❑ CP ❑ Other_____
K-11677 Adjustable trip lever drain ❑ CP ❑ PB
Optional Accessories
K-1491 Pillow ❑ 0 ❑ Other_____
K-1601 Footstop ❑ 0 ❑ Other_____
K-9696 Jet trim kit (metal finishes) ❑ CP ❑ PB ❑ Other_____
Product Specification
The oval shaped acrylic bath whirlpool shall be 60” (1524 mm) in length, 40” (1016 mm) in width, and 17-5/8” (448 mm) in height.
Product shall be for drop-in installation. Product shall have 6 individually adjustable ProFlex hydro-massage jets, a pump with
air switch and grounding-type plug-in cord, and an in-line heater. Product shall have custom pump locations and molded lumbar
supports and armrests. Product shall have an optional K-9696 whirlpool trim kit in various finishes. Bath whirlpool shall be
Kohler Model K-1146-____-____.
Page 1 of 2
1013793-4-
USA/Canada: 1-800-4KOHLER
E
(1-800-456-4537)
www.kohler.com
PROFLEX®6040
Technical Information
Fixture*:
Bathing well:
Basin area, bottom 46″ (1168 mm) x 19″ (483 mm)
Basin area, top 55″ (1397 mm) x 29″ (737 mm)
Weight 61 lbs (27.7 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 54 gal (204.4 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7.5
Heater: KW V Hz A
1.5 120 60 12.5
* Approximate measurement for comparison only.
Included components:
Cut-out template 114859-7
No change in measurements if
connected with the drain illustrated.
(K-11677 or K-11677M)
K-1146-*
20"
(508 mm)
K-1146-HN
7-1/2"
(191 mm)
Pump/Control
Access
Max
5/8" (16 mm)
4" (102 mm)
5" (127 mm)
1" (25 mm)
9" (229 mm)
Drain End
Required Electrical Service
Two dedicated circuits required, each protected with
Class A Ground-Fault Circuit-Interrupter (GFCI):
Pump/control 120 V, 15 A, 60 Hz
Heater 120 V, 15 A, 60 Hz
Locate the outlets behind the whirlpool and within 24”
(610 mm) of the pump and heater.
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
33 lbs/square foot (158 kg/square meter) loading.
The suction line extends 1” (25 mm) beyond the edge of the
rim. The pump base extends 1-1/8” (29 mm) beyond the edge
of the rim. Modify the framing as needed.
A minimum access panel is required at the pump location, as
illustrated. The access panel should be 20″ (508 mm) wide
and 15″ (381 mm) high.
29" (737 mm)
26" (660 mm)
20" (508 mm)
10" (254 mm)
1-1/4" (32 mm)
Symmetrical About C
Cut-Out Detail
29-3/4" (756 mm)
28" (711 mm)
20" (508 mm)
10" (254 mm)
L
1" (25 mm)
4"
(102 mm)
6" (152 mm)
8" (203 mm)
3-1/8"
(79 mm)
7-1/2"
(191 mm) Max
K-1146-HK
Pump/Control
Access
8" (203 mm)
60" (1524 mm)
2-1/2"
(64 mm)
17-5/8"
(448 mm)
3/8" (10 mm)
3" (76 mm)
2-7/8" (73 mm)
Product Diagram
PROFLEX®6040 CUSTOM BATH WHIRLPOOL WITH HEATER
Page2of2
1013793-4-
E
16-1/8"
(410 mm)
40" (1016 mm)
1-1/2" OD
1-1/2"
(38 mm)
Drop-In
Rim Detail
Loading...