Kohler K-1111-VLN Homeowner's Manual

Homeowners Guide

Bath Whirlpool

K-1111-VLN

M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de M corresponden a México
(Ej. K-12345M)
Français, page “Français-1”
Español, página ″Español-1”

1042760-5-D

Operating Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRICAL SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: When using electrical products, basic precautions should always be followed,
including the following:

DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this

unit unless they are closely supervised at all times.

WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the
whirlpool.

WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,
telephone, radio, or television) within 5’ (1.5 m) of this whirlpool.

WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical
history should consult a physician before using a whirlpool equipped with a heater.

WARNING: Risk of scalding. Do not allow the water temperature in the whirlpool to exceed
104°F (40°C).

Use this whirlpool only for its intended purpose as described in this manual. Do not use attachments not
recommended by the manufacturer.

Never drop or insert any object into any opening. Keep small objects such as bath toys and bathing
accessories out of the whirlpool while the unit is running.

Do not operate this unit without the guard (cover) over the suction fitting.
The whirlpool must be connected only to a supply circuit that is protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Such a GFCI or RCD should be provided by
the installer and should be tested on a routine basis. To test the GFCI or RCD, press the test button. The
GFCI or RCD should interrupt power. Press the reset button. Power should be restored. If the GFCI or RCD
fails to operate in this manner, the GFCI or RCD is defective. If the GFCI or RCD interrupts power to the
bath without the test button being pressed, a ground current is flowing, indicating the possibility of an
electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the problem corrected by a
qualified service representative before using.

WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs

when the internal temperature of the body reaches a level several degrees above the normal body
temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal
temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c)
unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to
exit the bath, and (f) unconsciousness resulting in the danger of drowning.

Flush your whirlpool system twice a month or more depending upon usage, as described in the ″Flush
System″ section.

Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use
heavy, vegetable-based shampoos or bath oils.

Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath
oil to foam excessively. For this reason, please don’t use these products during whirlpool operation.

1042760-5-D 2 Kohler Co.

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Company. Your Kohler Company product reflects the true passion for design,
craftsmanship, artistry, and innovation Kohler Company stands for. We are confident its dependability and
beauty will surpass your highest expectations, satisfying you for years to come.

All information in this guide is based upon the latest product information available at the time of
publication. At Kohler Company, we strive to fulfill our mission of improving the level of gracious living for
each person who is touched by our products and services. We reserve the right to make changes in product
characteristics, packaging, or availability at any time without notice.

Please take a few minutes to review this guide. Pay special attention to the care and cleaning instructions.

Kohler Co. 3 1042760-5-D

The user keypad (2 provided) allows
you to turn the whirlpool and heater on
and off and regulate the water flow.

The bath provides a reservoir
for the hydro-massage action.

Adjustable jets allow you to
adjust the air and water
flow and direction.

The pump motor (2 provided)
provides quiet, variable speed
power to circulate the water.

NOTE: Bath shown for illustrative

Backjets

The heater (2 provided)
helps maintain the water
temperature up to 104˚F
(40˚C).

purposes. Your bath
model may vary.

Your Kohler Whirlpool

The whirlpool is equipped with the following components:

•

Bath - The bath acts as a reservoir for water and provides a location for the hydro-massage action.

•

User Keypads (2) - Located within easy reach, the keypads allow you to turn the whirlpool on and
off, access all the whirlpool modes, and regulate the water flow or pulse speed. Available modes
will be illuminated in blue. Active modes will be illuminated in green.

•

Pump Motors (2) - The pump motors provide quiet, variable speed power to circulate the water and
create the soothing hydro-massage action.

•

Adjustable Jets - The adjustable jets may be positioned to optimize their hydro-massage effect. The
trim on the adjustable jets allow you to adjust the air and water flow.

•

Heaters (2) - The heaters are designed to automatically help maintain the temperature of the water
up to 104°F (40°C) to enhance your hydro-massage experience. The heaters turn on automatically
when the whirlpool is operating and turn off when the pump motors are turned off. The heaters
may be turned off through the keypad at any time while the pump motors are operating.

•

Pillows - The pillows provide a comfortable place to rest your head as you relax.

•

Remote Controls (2) - The waterproof remote controls bring all the whirlpool features to your
fingertips.

•

Chromatherapy - Add ambience to your bath with lights that automatically and continuously cycle
through the eight colors, or select just one color: white, violet, indigo blue, aqua blue, green, yellow,
orange, and red. One cycle through all eight colors takes approximately one minute. This mode may
be used with all modes of operation and also when the pumps are not operating.

•

LED Lights (3) - The LED lights illuminate the ledge separating the two bath spaces.

•

Effervescence Ports - The effervescence ports are intended to be a relaxing, soothing experience. The
Flexjets and backjets will automatically turn off when the effervescence mode is activated.

•

Backjets - This mode delivers massaging water to your back. The backjets pulse from the bottom to
the top of the whirlpool. Water flow and pulse action occur from two backjets at a time.

1042760-5-D 4 Kohler Co.

Flexjet Flow Mode
Activates Mode
Selected

Backjet Mode­Adjust Pulse

Rotate outer

Increases Flow
or Pulse Rate

Effervescence
Mode

Indicator Bar - Shows
Water Flow Volume or
Pulse Rate

ring to access
desired mode.

Chromatherapy ­Specific Color

Power
On/Off

Heater On/Off

Lighted User Keypad

Chromatherapy
Cycle

Decreases
Flow

Keypad above shows all features

Note:

available. Your keypad may vary
based on your whirlpool model.

User Keypads

Available modes will be illuminated in blue. Active modes will be illuminated in green.
Power Icon Turns the whirlpool pump on and off. Icons illuminated in blue indicate available

Chromatherapy
Specific Color

Outer Ring Rotate the outer ring to the desired mode. The selected mode will flash blue.
Backjet Mode Rotate the outer ring to select this mode. Press OK, then press the up or down arrow to

OK Activates the desired mode.
Flexjet Flow

Mode
Up Arrow Increases the water flow when the Flexjet flow mode is active. Increases the pulse speed

Effervescence
Mode

Indicator Bar Displays the water flow volume in the Flexjet flow mode. Displays the pulse speed in the

Chromatherapy
Cycle

Down Arrow Decreases the water flow when the Flexjet flow mode is active. Decreases the pulse speed

Heater Automatically engages when the power icon is selected. Rotate the outer ring until the

modes/features. Modes which are operating will be illuminated in green.
Rotate the outer ring to select this mode. Press OK, press the up or down arrow to select a

color, then press OK again. Only one of the two keypads controls this mode.

increase or decrease the pulsing action. Rotate the outer ring to the Flexjet mode, press OK
to activate the mode, then press the up or down arrow on the keypad to increase or
decrease water flow to the backjets and all other active modes.

Rotate the outer ring to select this mode. Press OK, then press the up or down arrow to
increase or decrease the jet water flow.

when the neckjet or backjet mode is active.
Rotate the outer ring to select this mode, then press OK. The effervescence action will start

at the water flow volume last set in the Flexjet flow mode. Press the up or down arrow to
increase or decrease the water flow. Press OK while the effervescence mode is flashing to
turn off the effervescence ports.

neckjet or backjet mode.
Rotate the outer ring to select this mode, then press OK. The chromatherapy lights will

automatically and continuously cycle through eight colors. One cycle through all eight
colors takes approximately one minute. Only one of the two keypads controls this mode.

when the neckjet or backjet mode is active.

heater mode is flashing, then press OK to turn the heater off. Press OK again to turn the
heater back on.

Kohler Co. 5 1042760-5-D

Fill with water until the backjet level
probes are covered with water.

Level
Probes

Position the jet nozzles

Turn the Flexjet
trim clockwise to

to direct the water flow
as desired.

decrease the flow.

Turn the Flexjet trim
counterclockwise to
increase the flow.

Operation

NOTE: Please read these steps carefully before operating your whirlpool.

NOTE: The water temperature in the whirlpool should not exceed 104°F (40°C). The heater will

automatically turn off as the water temperature approaches 104°F (40°C) and will remain off until the
water cools.

Turn the jet trim fully counterclockwise. Position the jet nozzles so they face down toward the basin.

Close the drain and fill the bath above the backjet level probes.
Place your hand in the bath to test the water temperature for comfort and safety, then carefully

enter the bath.
Press the power icon. The heater will turn on and the whirlpool will start at a medium water flow

volume. The chromatherapy cycle icon will illuminate on the keypad and three small lights near the
whirlpool floor will illuminate until the keypad goes into sleep mode.

Press the up or down arrow to increase or decrease the water flow volume. The indicator bar in the
center of the keypad will display the current water flow volume.

Rotate the jet trim clockwise to reduce the air/water flow or counterclockwise to increase the
air/water flow.

Position the Flexjet nozzles to direct the water flow to maximize your hydro-massage experience.
Rotate the outer ring until the heater mode is flashing, then press OK. The heater will turn off. Press

OK again to turn the heater back on.

NOTE: In backjet mode, if the water level is lower than the backjet level probes, this mode will stop. The
backjet icon and indicator bar on the user keypad will flash. The backjet mode will automatically restart
when the water level reaches the backjet level probes.

Rotate the outer ring until the backjet mode is flashing, then press OK. Press the up or down arrow
to increase or decrease the pulsing action. Rotate the outer ring to the Flexjet mode, press OK to
activate the mode, then press the up or down arrow on the keypad to increase or decrease water
flow to the backjets and all other active modes.

Rotate the outer ring until the chromatherapy cycle is flashing, then press OK to activate it. Press
OK while the chromatherapy mode is active to turn off this mode.

Rotate the outer ring to the chromatherapy specific color. When flashing, press OK to activate it.
Press the up or down arrow to reach the desired color, then press OK to activate the desired color.

Press the power icon to turn the whirlpool off. The three small lights near the whirlpool floor will
remain illuminated until the keypad goes into sleep mode.

1042760-5-D 6 Kohler Co.

Operation (cont.)

Repeat the steps above to verify the second keypad is operating properly, less the chromatherapy
functions.

NOTE: The whirlpool will automatically shut off approximately 20 minutes after continuous operation. If
desired, press the power icon to reactivate the whirlpool.

Care and Cleaning

For best results, keep the following in mind when caring for your KOHLER product:

•

Always test your cleaning solution on an inconspicuous area before applying to the entire surface.

•

Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.

•

Do not allow cleaners to soak on surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring
pad to clean surfaces.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &
Cleaning information, call 1-800-456-4537.

Flush System

NOTE: Flush your whirlpool system twice a month or more, depending upon usage.

Turn the jet trim rings fully clockwise to remove air induction.

Fill the whirlpool with warm water above the backjet level probes or leave water in the whirlpool
after using.

Add 2 teaspoons (10 ml) of a low-foaming, powder automatic dishwasher detergent and 20 ounces
(590 ml) of household bleach (5% - 6% sodium hypochlorite) to the water.

Run the whirlpool for 5 to 10 minutes. Turn off the whirlpool and drain the water.
If desired, rinse the bath surfaces with water.
Rinse the surfaces of the jets, faucet, handrails, and drain, and wipe them dry with a soft cloth.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year
from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection
discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not
responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home
Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI
53044, USA, or by calling 1-800-4KOHLER (1-800-456-4537) from within the USA and Canada, and
001-877-680-1310 from within Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how

long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,
so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You
may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

Kohler Co. 7 1042760-5-D

Warranty

KOHLER CO.
It is recommended that at the time of purchase, you verify that all accessories and components are complete

in this package.
This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the

date of purchase as shown on the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its authorized distributors.

2. To obtain warranty service, please present the invoice and corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new
replacement or an equivalent model (in those cases that the model has been discontinued) when the product
is beyond repair, without any charge to the consumer.

4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.

5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may
substitute the warranty in the case that there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS
The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the instructions concerning use and operation set
forth in the owner’s manual or installation instructions, and when the recommendations and warnings
included are not observed.

2. When the product has been modified or dismantled partially or totally; or has been used in a negligent
fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not
authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster such as fire or acts of God, including
flooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can
exercise your rights under this warranty, please call 001-877-680-1310.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V.
AV. CARLOS PACHECO NO. 7200
CHIHUAHUA, CHIH., MEXICO C.P. 31060
TEL: [phone]

Troubleshooting

This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualified
electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale
distributor.

1042760-5-D 8 Kohler Co.

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

1. User keypad does not

illuminate when power
button is pressed or outer
ring is rotated.

2. Motor starts, but all jets

are not functioning.

3. User keypad is

illuminated, but does not
respond to buttons or
outer ring.

4. User keypad indicator bar

keeps scanning at
power-up.

5. User keypad is

illuminated, but pump
will not start.

6. Motor runs but pump will

not prime (cavitates).

A. No power to control. A. Check wiring and connect power. If

B. GFCI or RCD tripped. B. Reset GFCI or RCD.
C. Wiring harness from user

keypad to control is loose,
disconnected, or damaged.

D. User keypad does not work. D. Replace user keypad. Refer to the

E. Control does not work. E. Replace control. Refer to the

A. Jet is closed. A. Rotate jet trim counterclockwise to

B. Jet not installed correctly. B. Reinstall jet; check for O-ring

C. Jets are blocked. C. Remove blockage.
A. Control program is locked. A. Reset GFCI or RCD.
B. Wiring harness from user

keypad to control is loose,
disconnected, or damaged.

C. User keypad does not work. C. Replace user keypad. Refer to the

D. Control does not work. D. Replace control. Refer to the

A. Control program is locked. A. Reset GFCI or RCD.
B. Wiring harness from user

keypad to control is loose,
disconnected, or damaged.

C. User keypad does not work. C. Replace user keypad. Refer to the

D. Control does not work. D. Replace control. Refer to the

A. Power cord from pump to

control is loose, disconnected, or
damaged.

B. Pump does not work. B. Replace pump. Refer to the

C. Control does not work. C. Replace control. Refer to the

A. Motor/Pump is shimmed too

high.

B. Small air leak at pump inlet. B. Securely tighten nut(s) on intake

C. Motor/pump does not work. C. Replace motor/pump. Refer to the

D. Control does not work. D. Replace control. Refer to the

problem persists, Refer to the
installer/dealer.

C. Check wiring for proper

connections. Replace wiring
harness if necessary. Refer to the
installer/dealer.

installer/dealer.

installer/dealer.

open.

damage.

B. Check wiring for proper

connections. Replace wiring
harness if necessary. Refer to the
installer/dealer.

installer/dealer.

installer/dealer.

B. Check wiring for proper

connections. Replace wiring
harness if necessary. Refer to the
installer/dealer.

installer/dealer.

installer/dealer.

A. Check wiring for proper

connections. If problem persists,
Refer to the installer/dealer.

installer/dealer.

installer/dealer.

A. Lower pump/control to subfloor

level.

side of pump.

installer/dealer.

installer/dealer.

Kohler Co. 9 1042760-5-D

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

7. Pump stops before 18

minutes.

8. Pump does not

automatically stop after 22
minutes.

9. Pump will not turn off

when the power button
on user keypad is
pressed.

10. Pump operates but

variable speed feature
does not work.

11. Bath water cools while

pump is operating.

12. Noisy operation. A. Pump banding straps have not

Remote control does not

13.

work or operates both
pumps.

14. Lights near whirlpool

floor do not work.

A. GFCI or RCD tripped. A. Identify source of fault, and correct.

B. Suction is blocked. B. Remove obstruction.
C. Jets are blocked. C. Remove blockage.
D. Motor overheated and

protection device activated.

A. 20-minute timer inadvertently

disabled.

A. User keypad does not work. A. Replace user keypad. Refer to the

B. Control does not work. B. Replace control. Refer to the

A. Motor/pump does not work. A. Replace motor/pump. Refer to the

B. Control does not work. B. Replace control. Refer to the

A. Water temperature above 104°F

(40°C).

B. Heater is turned off on user

keypad.

C. Wiring from heater to control is

loose, disconnected, or
damaged.

D. Heater does not work. D. Replace heater. Refer to the

E. Control does not work. E. Replace control. Refer to the

been cut.

B. Dry or dislodged jet O-ring

(squeal).

A. Batteries improperly installed or

dead.

B. Antenna on wiring harness is

damaged.

C. Remote control not

programmed correctly.

D. Remote control does not work. D. Replace remote control.
E. Control does not work. E. Replace control. Refer to the

A. Wiring damage. A. Check for loose or damaged wires.

Reset GFCI or RCD.

D. Check for blockage at suction

and/or jets. Remove blockage and
allow motor to cool.

A. See Service Manual.

installer/dealer.

installer/dealer.

installer/dealer.

installer/dealer.

A. Allow bath water to cool.

B. Turn heater on.

C. Check wiring for proper

connections. Refer to the
installer/dealer.

installer/dealer.

installer/dealer.

A. Cut pump banding straps with tin

snips.

B. Remove jet, replace and lubricate

O-ring, and reinstall jet.

A. Replace batteries.

B. Replace wiring harness. Refer to

the installer/dealer.

C. See Homeowners Guide or Service

Manual.

installer/dealer.

Repair or replace as needed.

Chromatherapy Lights

Symptoms Probable Causes Recommended Action

1. Chromatherapy lights do

not work.

Backjet System

1042760-5-D 10 Kohler Co.

A. Loose, disconnected, or

damaged wiring/connections.

B. Control does not work. B. Replace control. Refer to the

A. Check wiring for proper

connections. Replace wiring if
necessary. Refer to the
installer/dealer.

installer/dealer.

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

1. Backjets do not operate. A. Whirlpool pump is not

A. Turn on pump.

operating.

B. Backjet butterfly valve does not

open.

B. Check for loose connections or

wires leading from the backjet
pulse canister to the control.
Replace the backjet pulse canister
or control if necessary. Refer to the
installer/dealer.

C. Not enough water in whirlpool. C. Fill whirlpool so water level

sensors.

D. Actuator switch does not work. D. Replace the actuator switch. Refer

to the installer/dealer.

E. Power from the pump motor to

the control is off.

E. Check for loose connections or

wires leading from the pump
motor to the control. Refer to the
installer/dealer.

F. Backjet pipe is blocked. F. Remove blockage.
G. Switch wire from switch to

control is disconnected.

G. Reconnect or replace switch wires

that use a modular plug. Refer to
the installer/dealer.

2. Backjets do not pulse. A. Pulse canister does not work. A. Check for loose connections or

wires leading from the pulse
canister control. Replace the pulse
canister or control if necessary.
Refer to the installer/dealer.

B. Switch does not work. B. Replace the switch. Refer to the

installer/dealer.

C. Switch wire from the switch to

the control is disconnected.

C. Reconnect or replace the switch

wires that the modular plug. Refer
to the installer/dealer.

Effervescence Ports

Symptoms Probable Causes Recommended Action

1. Effervescence ports do not

work.

A. Whirlpool pump is not

operating.

A. Turn on pump.

B. Butterfly valve does not open. B. Replace the butterfly valve. Refer

to the installer/dealer.

C. Pump does not work. C. Refer to the Service Manual to

troubleshoot the system. Refer to
the installer/dealer.

D. Control does not work. D. Replace the control. Refer to the

installer/dealer.

2. Effervescence ports do not

bubble.

A. Air intake on the suction line is

blocked.

A. Remove blockage.

B. Water flow is too low. B. Increase the water flow.

Kohler Co. 11 1042760-5-D

A

B

**Finish/color code must be specified when ordering.

Service Parts

1042760-5-D 12 Kohler Co.

A

1023292

Cap

1-1/2" Tubing

*Note: All tubing 1" unless otherwise noted.

In-line Heater

1-1/2" Tubing

1/2" Tubing

1/2" Tubing

1/2" Tubing

3/4" Tubing

94528

Check Valve

1/2" Tubing

95462**

Pillow

1-1/2" Tubing

1049953

Lens

1049954

Nut

1048233

LED Lighting
Harness

1-1/4" Tubing

1015019

Plug/Wire Assembly

1048232

Plug/Wire Assembly

1-1/4" Tubing

1-1/2" Tubing

**Finish/color code must be specified when ordering.

Kohler Co. 13 1042760-5-D

B

*Note: All tubing 1" unless otherwise noted.

1/2" Tubing

1-1/2" Tubing

94528

Check Valve

1/2" Tubing

1/2" Tubing

1/2" Tubing

1-1/2" Tubing

1-1/4" Tubing

1-1/4" Tubing

In-line Heater

1023292

Cap

3/4" Tubing

1-1/2" Tubing

1-1/4" Tubing

1-1/4" Tubing

1015019

Plug/Wire Assembly

1015012

Plug/Wire Assembly

**Finish/color code must be specified when ordering.

1042760-5-D 14 Kohler Co.

1003065

Suction Flange
Removal Tool

93836 (1/2")
93837 (3/4")
93838 (1")
93839 (1-1/4")
94853 (1-1/2")

Tube (w/Couplings)

65054**

Screw

65226**

Suction Cover Plug

96708

Flange

73518

Plug

96895**
65061**

Cover

65886
60050

Gasket

(Colored Finishes)
(Metal Finishes)

91967

Check Valve

93685

Housing

(Acrylic and FRP)
(Cast Iron)

1086350

Flange Removal Wrench

67429

Flange

34353

O-Ring

67665

Plug

Single Jet For Whirlpools
With 5 or Less Jets

88532**

(Colored Finishes)

88531**

1045715-P

Silicone Lube
Packet

(Metal Finishes)

Jet

Single Jet For Whirlpools
With 6 or More Jets

88530**

30739

Jet Tool

**Finish/color code must be specified when ordering.

(Colored Finishes)

88529**

(Metal Finishes)

Jet

67889

Jet Housing

65885 (Acrylic and FRP)
67668 (Cast Iron)

Gasket

Kohler Co. 15 1042760-5-D

67065

Ground Lug

61776

Lock Washer

61845-K

Copper Grounding Wire

1080775

Pump Tee

60320

Screw

94821

O-Ring

94821

O-Ring

1080774

Union Assy

93893

Cover

1033678

Screw

93892-A

Electrical Box

60320

Screw

To Tee Heater

61776

Lock Washer

67065

Ground Lug

93003

Strain Relief

1018964

Bracket

90153

Locknut

1019432

Carriage Bolt

90154

Locknut

1019719

Connector

1012855

Nut

1016957

Pump

1010676

Cover

1010677

Screw

94821

O-Ring

To In-line Heater

1010548

Volute

1016958

Motor

1010673

Seal

1016960

Impeller

1010675

O-Ring

1019444-A [3/4" (1.9 cm)]
1019444-B [1-3/4" (4.4 cm)]
1019444-C [2" (5.1 cm)]
1019444-D [1-1/2" (3.8 cm)]
1019444-E [1" (2.5 cm)]
1019444-F [1-1/4" (3.2 cm)]
1019444-G [2-1/4" (5.7 cm)]
1019444-H [2-1/2" (6.4 cm)]
1019444-J [2-3/4" (7 cm)]
1019444-K [3" (7.6 cm)]
1019444-L [1/2" (1.3 cm)]
1019444-M [1/4" (6 mm)]

Spacer

1019445-A [1-3/4" (4.4 cm)]
1019445-B [2-3/4" (7 cm)]
1019445-C [3" (7.6 cm)]
1019445-D [2-1/2" (6.4 cm)]
1019445-E [2" (5.1 cm)]
1019445-F [2-1/4" (5.7 cm)]
1019445-G [3-1/4" (8.3 cm)]
1019445-H [3-1/2" (8.9 cm)]
1019445-J [3-3/4" (9.5 cm)]
1019445-K [4" (10.2 cm)]
1019445-L [1-1/2" (3.8 cm)]
1019445-M [1-1/4" (3.2 cm)]

Stud

1018661
1018663

Control

**Finish/color code must be specified when ordering.

(One Outlet)
(Two Outlets)

Outlet

1019447-A [1/4" (6 mm)]
1019447-B [1/2" (1.3 cm)]
1019447-C [3/4" (1.9 cm)]

Isolation Mount

1042760-5-D 16 Kohler Co.

1022408

In-line Heater

1032545

Housing

1012653

Adapter

1012653

Adapter

94821

O-Ring

1012916

Nut w/Screws

1018710

Tee Heater

94821

O-Ring

1011679

Gasket

1012977

Adapter

1012977

Adapter

94821

O-Ring

1012916

Nut with Screws

1011679

Gasket

**Finish/color code must be specified when ordering.

94821

O-Ring

Kohler Co. 17 1042760-5-D

93841

Screw

1019933

Chromatherapy Lights

1010618

Elbow

1012821

Light Housing

Effervescence Ports

1001878

Housing

93315

Gasket

93552**

Flange Cap

1035480**

Flange

**Finish/color code must be specified when ordering

96744

Flange Removal Tool

1042760-5-D 18 Kohler Co.

1080774

Union Assy

94821

O-Ring

1023753

Butterfly Valve

96956

Butterfly Kit

63149

Screw

1016466

Motor

50506

Screw

94821

O-Ring

1080774

Union Assy

**Finish/color code must be specified when ordering.

Kohler Co. 19 1042760-5-D

1023381

Wrench

Carefully study decal and cover
detail below for proper service
part identification.

1013452**

Dial Trim

1013453

Spring

1020677

Gasket

65157

Nut

1013499

Housing

91639

O-Ring

1020678-A

Cover/Circuit Board
(w/Wrench)

1020678-C

Cover/Circuit Board
(w/Wrench)

1020678-E

Cover/Circuit Board
(w/Wrench)

1020678-N

Cover/Circuit Board
(w/Wrench)

1013497-A

Decal

1013497-C

Decal

1013497-E

Decal

91639

O-Ring

91639

O-Ring

91639

O-Ring

1020678-B

Cover/Circuit Board
(w/Wrench)

1020678-D

Cover/Circuit Board
(w/Wrench)

1020678-M

Cover/Circuit Board
(w/Wrench)

1020678-P

Cover/Circuit Board
(w/Wrench)

1013497-B

Decal

1013497-D

Decal

1013497-M

Decal

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

1013497-N

Decal

**Finish/color code must be specified when ordering.

O-Ring

1013497-P

Decal

91639

O-Ring

1042760-5-D 20 Kohler Co.