Kohler CH742, CH732, CH682, CH752 Service Manual

CH682, CH732, CH742, CH752

Service Manual

IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Refer to operating

instruction of equipment that this engine powers.

Ensure engine is stopped and level before performing any maintenance or service.

2 Safety
3 Maintenance

5 Specifi cations
13 Tools and Aids
16 Troubleshooting
20 Air Cleaner/Intake
21 Fuel System
27 Governor System
29 Lubrication System
31 Electrical System
38 Starter System
42 Disassembly/Inspection and Service
56 Reassembly

124 690 34 Rev. D KohlerEngines.com

Safety

SAFETY PRECAUTIONS

WARNING: A hazard that could result in death, serious injury, or substantial property damage.

CAUTION: A hazard that could result in minor personal injury or property damage.

NOTE: is used to notify people of important installation, operation, or maintenance information.

WARNING

Explosive Fuel can cause
fi res and severe burns.

Do not fi ll fuel tank while
engine is hot or running.

Gasoline is extremely fl ammable
and its vapors can explode if
ignited. Store gasoline only in
approved containers, in well
ventilated, unoccupied buildings,
away from sparks or fl ames.
Spilled fuel could ignite if it comes
in contact with hot parts or sparks
from ignition. Never use gasoline
as a cleaning agent.

WARNING

Rotating Parts can cause
severe injury.

Stay away while engine
is in operation.

Keep hands, feet, hair, and
clothing away from all moving
parts to prevent injury. Never
operate engine with covers,
shrouds, or guards removed.

WARNING

Carbon Monoxide can
cause severe nausea,
fainting or death.

Avoid inhaling exhaust
fumes.

Engine exhaust gases contain
poisonous carbon monoxide.
Carbon monoxide is odorless,
colorless, and can cause death if
inhaled.

Accidental Starts can
cause severe injury or
death.

Disconnect and ground
spark plug lead(s) before
servicing.

Before working on engine or
equipment, disable engine as
follows: 1) Disconnect spark plug
lead(s). 2) Disconnect negative (–)
battery cable from battery.

Hot Parts can cause
severe burns.

Do not touch engine
while operating or just
after stopping.

Never operate engine with heat
shields or guards removed.

Cleaning Solvents can
cause severe injury or
death.

Use only in well
ventilated areas away
from ignition sources.

Carburetor cleaners and solvents
are extremely fl ammable. Follow
cleaner manufacturer’s warnings
and instructions on its proper and
safe use. Never use gasoline as a
cleaning agent.

WARNING

WARNING

WARNING

Electrical Shock can
cause injury.

Do not touch wires while
engine is running.

Damaging Crankshaft
and Flywheel can cause
personal injury.

Using improper procedures can
lead to broken fragments. Broken
fragments could be thrown from
engine. Always observe and use
precautions and procedures when
installing fl ywheel.

Failure to utilize or
reassemble debris
screen as designed could
result in debris screen
failure and serious
personal injury.

CAUTION

CAUTION

CAUTION

2 24 690 34 Rev. DKohlerEngines.com

Maintenance

MAINTENANCE INSTRUCTIONS

WARNING

Accidental Starts can cause severe injury or
death.

Disconnect and ground spark plug lead(s)
before servicing.

Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repair
establishment or individual; however, warranty repairs must be performed by a Kohler authorized dealer.

MAINTENANCE SCHEDULE

Weekly

● Check air cleaner element. Air Cleaner/Intake

Every 100 Hours or Annually¹

● Change oil. Lubrication System

● Remove cooling shrouds and clean cooling areas. Air Cleaner/Intake

● Check oil cooler fi ns, clean as necessary (if equipped). Lubrication System

Every 200 Hours

● Change oil fi lter. Lubrication System

● Replace fuel fi lter.

Before working on engine or equipment, disable engine as
follows: 1) Disconnect spark plug lead(s). 2) Disconnect
negative (–) battery cable from battery.

Every 250 Hours¹

● Replace air cleaner element and check inner element. Air Cleaner/Intake

Every 500 Hours¹

● Replace air cleaner inner element. Air Cleaner/Intake

● Replace spark plugs and set gap. Electrical System

Every 500 Hours

2

● Have crankshaft spline lubricated.

1

Perform these procedures more frequently under severe, dusty, dirty conditions.

2

Have a Kohler authorized dealer perform this service.

REPAIRS/SERVICE PARTS

Kohler genuine service parts can be purchased from Kohler authorized dealers. To fi nd a local Kohler authorized
dealer visit KohlerEngines.com or call 1-800-544-2444 (U.S. and Canada).

324 690 34 Rev. D KohlerEngines.com

Maintenance

OIL RECOMMENDATIONS

We recommend use of Kohler oils for best performance.
Other high-quality detergent oils (including synthetic)
of API (American Petroleum Institute) service class SJ
or higher are acceptable. Select viscosity based on
air temperature at time of operation as shown in table
below.

FUEL RECOMMENDATIONS

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings,
away from sparks or fl ames. Spilled fuel could ignite
if it comes in contact with hot parts or sparks from
ignition. Never use gasoline as a cleaning agent.

STORAGE

If engine will be out of service for 2 months or more
follow procedure below.

1. Add Kohler PRO Series fuel treatment or equivalent
to fuel tank. Run engine 2-3 minutes to get stabilized
fuel into fuel system (failures due to untreated fuel
are not warrantable).

2. Change oil while engine is still warm from operation.
Remove spark plug(s) and pour about 1 oz. of
engine oil into cylinder(s). Replace spark plug(s) and
crank engine slowly to distribute oil.

3. Disconnect negative (-) battery cable.

4. Store engine in a clean, dry place.

NOTE: E15, E20 and E85 are NOT approved and

should NOT be used; effects of old, stale or
contaminated fuel are not warrantable.

Fuel must meet these requirements:

● Clean, fresh, unleaded gasoline.

● Octane rating of 87 (R+M)/2 or higher.

● Research Octane Number (RON) 90 octane minimum.

● Gasoline up to 10% ethyl alcohol, 90% unleaded is

acceptable.

● Methyl Tertiary Butyl Ether (MTBE) and unleaded
gasoline blend (max 15% MTBE by volume) are
approved.

● Do not add oil to gasoline.

● Do not overfi ll fuel tank.

● Do not use gasoline older than 30 days.

4 24 690 34 Rev. DKohlerEngines.com

Engine Dimensions

Specifi cations

319.23 [12.568]
SPARK PLUG

REMOVAL

10.09 [.397]
SPARK PLUG
BOOT

FUEL FILTER

312.01 [12.284]
SPARK PLUG

BOOT REMOVAL

135.00
[5.315]

AIR FILTER

RAIN CAP

REMOVAL

35.31 [1.390]
SPARK PLUG
REMOVAL

20°

C

CRANKSHAFT

L

FUEL PUMP

FUEL PUMP

14.52 [.572]
SPARK PLUG
BOOT REMOVAL

15.70 [.618]
OIL FILTER
REMOVAL

C

MOUNTING

L

HOLE "A"

142.89
[5.626]

92.98
[3.661]

414.52 [16.320]

SAFETY AIR FILTER

ELEMENT REMOVAL

450.90
[17.752]

298.74
[11.761]

272.52
[10.729]

C

ENGINE

L

92.10
[3.626]

184.20
[7.252]

FLYWHEEL SIDE

526.84 [20.742]
PRIMARY AIR FILTER
ELEMENT REMOVAL

VALVE
COVER

ENGINE MOUNTING SURFACE

4X Ø 10.3
MOUNTING HOLES (THRU)

130.00 [5.118]
AIR FILTER
COVER
ASSEMBLY
REMOVAL

72.81 [2.867]
SPARK PLUG REMOVAL

52.02 [2.048]
SPARK PLUG BOOT REMOVAL

22.77 [.897]
SPARK PLUG BOOT

20°

311.90
[12.280]
SPARK PLUG
BOOT REMOVAL

319.12
[12.564]
SPARK PLUG
REMOVAL

M8 X 1.25
4 STUDS

50.00 [1.969]
EXHAUST
PORT #1
MOUNTING
HOLES

7/16-14 UNC 2B [INCH]

21.0 [.827] Ø 196.85 [7.750] B.C.
OPTIONAL BOLT PATTERN
5/16-24 UNC 2B [INCH]

17.0 [.669] Ø 127.0 [5.000] B.C.

30°

SOLENOID
SHIFT
STARTER

PILOT Ø 177.80 [7.000]

OPTIONAL PILOT Ø 146.050 [5.750]

Dimensions in millimeters.

Inch equivalents shown in [ ].

334.78
[13.180]

122.10

75.35

[4.807]

65.00 [2.559]
MUFFLER
MOUNTING

C

MOUNTING

L

HOLE "A"

PTO SIDE

[2.966]

3/8-16 UNC 2B [INCH]

21.0 [.827] Ø 165.1 [5.000] B.C.

7/16-14 UNC 2B [INCH]

21.0 [.827] Ø 196.85 [7.750] B.C.

ENGINE MOUNTING
SURFACE

LIFT STRAP

OIL FILL LOCATION

30°

283.58
[11.164]
MUFFLER
MOUNTING

308.17
[12.133]

50.00 [1.969]
EXHAUST
PORT #2
MOUNTING
HOLES

.+(6564#2


=?

1+.&4#+02.7)
026=+0%*?


=?

%

52#4-

.

2.7)



=?

=?

56#46'45+&'


=?
/7((.'4/1706+0)
$155'5


=?
':*#756
2146

%

/1706+0)

.

*1.'“#”


=?

'0)+0'
/1706+0)
574(#%'

622.41
[24.504]

5/8-18 UNF 2B [INCH]

38.10 [1.500]

Ø 36.50 [1.437]

155.58
[6.125]

152.08 [5.987]
OIL FILTER

32.00 [1.260]
EXHAUST PORT #2

67.50 [2.657]
MUFFLER MOUNTING
BOSSES

OIL FILL

OIL DIPSTICK

113.08 [4.452]

95.50 [3.760]

A

A

(C-2,2)

5.50 [.217]
PILOT

C

MOUNTING

L

HOLE "A"

100.00
[3.937]

370.68 [14.594]

115.88 [4.562]

42.25
[1.663]

30.00 [1.181]
C

SPARK

L

PLUG

51.00

52.75
[2.008]

[2.077]

OIL FILTER

89.00
[3.504]

OIL FILTER SIDE

FUEL PUMP

12.28

REGULATOR

[.483]

RECTIFIER

ENGINE MOUNTING SURFACE

OIL DRAIN PLUG
3/8 NPT [INCH]

524 690 34 Rev. D KohlerEngines.com

Specifi cations

ENGINE IDENTIFICATION NUMBERS

Kohler engine identifi cation numbers (model, specifi cation and serial) should be referenced for effi cient repair,
ordering correct parts, and engine replacement.

Model . . . . . . . . . . . . . . . . . . . . . CH682

Command Engine

Horizontal Shaft

Numerical Designation

Specifi cation . . . . . . . . . . . . . . . CH682-0001

Serial . . . . . . . . . . . . . . . . . . . . . 4323500328

Year Manufactured Code Factory Code
Code Year
43 2013
44 2014
45 2015

GENERAL SPECIFICATIONS

Bore 80 mm

3,6

CH682 CH732 CH742 CH752

83 mm (3.27 in.)

(3.15 in.)
Stroke 69 mm (2.72 in.)
Displacement 694 cc

747 cc (45.6 cu. in.)

(42.4 cu. in.)

Oil Capacity (refi ll) 1.6-1.8 L (1.7-1.9 U.S. qt.)

Maximum Angle of Operation (@ full oil level)

TORQUE SPECIFICATIONS

3,5

4

25°

CH682 CH732 CH742 CH752

Blower Housing and Sheet Metal

M5 Fasteners 6.2 N·m (55 in. lb.) into new holes

4.0 N·m (35 in. lb.) into used holes

M6 Fasteners 10.7 N·m (95 in. lb.) into new holes

7.3 N·m (65 in. lb.) into used holes

Carburetor, Intake Manifold, and Air Cleaner

Intake Manifold Mounting Fastener (torque in 2
increments)

fi rst to 7.4 N·m (66 in. lb.)

fi nally to 9.9 N·m (88 in. lb.)

Adapter (for Heavy-Duty Air Cleaner) Mounting
Fastener 9.9 N·m (88 in. lb.)

Air Cleaner Nut (torque in 2 increments) fi rst to 7.3 N·m (65 in. lb.)

fi nally to 8.2 N·m (73 in. lb.)

Closure Plate

Fastener 24.4 N·m (216 in. lb.)

Connecting Rod

Cap Fastener (torque in increments) 13.6 N·m (120 in. lb.)

3

Values are in Metric units. Values in parentheses are English equivalents.

4

Exceeding maximum angle of operation may cause engine damage from insuffi cient lubrication.

5

Lubricate threads with engine oil prior to assembly.

6

Any and all horsepower (hp) references by Kohler are Certifi ed Power Ratings and per SAE J1940 & J1995 hp

standards. Details on Certifi ed Power Ratings can be found at KohlerEngines.com.

6 24 690 34 Rev. DKohlerEngines.com

Specifi cations

TORQUE SPECIFICATIONS

3,5

CH682 CH732 CH742 CH752

Crankcase

Breather Cover Fastener 11.3 N·m (100 in. lb.) into new holes

7.3 N·m (65 in. lb.) into used holes

Oil Drain Plug 13.6 N·m (10 ft. lb.)

Cylinder Head

Fastener (torque in 2 increments)
Nut fi rst to 16.9 N·m (150 in. lb.)

fi nally to 35.5 N·m (315 in. lb.)

Bolt (torque in 2 increments) fi rst to 22.6 N·m (200 in. lb.)

fi nally to 41.8 N·m (370 in. lb.)

Rocker Arm Screw 18.1 N·m (160 in. lb.)

Flywheel

Fan Fastener 9.9 N·m (88 in. lb.)
Flywheel Retaining Screw 66.4 N·m (49 ft. lb.)

Fuel Pump-Pulse

Fastener 2.3 N·m (20 in. lb.)

Governor

Lever Nut 6.8 N·m (60 in. lb.)

Ignition

Spark Plug 27 N·m (20 ft. lb.)
Module Fastener 4.0-6.2 N·m (35-55 in. lb.)
Rectifi er-Regulator Fastener 1.4 N·m (12.6 in. lb.)

Muffl er

Retaining Nut 24.4 N·m (216 in. lb.)

Oil Cooler

Adapter Nipple 27 N·m (20 ft. lb.)

Oil Pump

Oil Pump Style A

Screw (torque in 2 increments) 10.7 N·m (95 in. lb.) into new hole

6.7 N·m (60 in. lb.) into used holes

Oil Pump Style B

Screw (no torque sequence) 9.0 N·m (80 in. lb.)

3

Values are in Metric units. Values in parentheses are English equivalents.

5

Lubricate threads with engine oil prior to assembly.

724 690 34 Rev. D KohlerEngines.com

Specifi cations

TORQUE SPECIFICATIONS

Oil Sentry

™

3,5

CH682 CH732 CH742 CH752

Pressure Switch 4.5 N·m (40 in. lb.)

Solenoid (Starter)

Mounting Hardware 4.0-6.0 N·m (35-53 in. lb.)
Nut, Positive (+) Brush Lead 8.0-11.0 N·m (71-97 in. lb.)

Speed Control Bracket

Fastener 10.7 N·m (95 in. lb.) into new holes

7.3 N·m (65 in. lb.) into used holes

Starter Assembly

Thru Bolt 5.6-9.0 N·m (49-79 in. lb.)
Mounting Screw 15.3 N·m (135 in. lb.)
Brush Holder Mounting Screw 2.5-3.3 N·m (22-29 in. lb.)

Stator

Mounting Screw 6.2 N·m (55 in. lb.)

Valve Cover

Yellow O-Ring Style Cover Fastener
w/Integral Metal Spacers 6.2 N·m (55 in. lb.)

CLEARANCE SPECIFICATIONS

3

CH682 CH732 CH742 CH752

Camshaft

End Play 0.076/0.127 mm (0.0030/0.0050 in.)
Running Clearance 0.025/0.063 mm (0.0010/0.0025 in.)
Bore I.D.

New
Max. Wear Limit

20.000/20.025 mm (0.7874/0.7884 in.)

20.038 mm (0.7889 in.)

Bearing Surface O.D.
New
Max. Wear Limit

19.962/19.975 mm (0.7859/0.7864 in.)

19.959 mm (0.7858 in.)

Connecting Rod

Connecting Rod-to-Crankpin Running Clearance
New
Max. Wear Limit

0.030/0.055 mm (0.0012/0.0022 in.)

0.070 mm (0.0028 in.)
Connecting Rod-to-Crankpin Side Clearance 0.26/0.63 mm (0.0102/0.0248 in.)
Connecting Rod-to-Piston Pin Running Clearance 0.015/0.028 mm (0.0006/0.0011 in.)
Piston Pin End I.D.

New
Max. Wear Limit

17.015/17.023 mm (0.6699/0.6702 in.)

17.036 mm (0.6707 in.)

Crankcase

Governor Cross Shaft Bore I.D.
New
Max. Wear Limit

8.025/8.075 mm (0.3159/0.3179 in.)

8.088 mm (0.3184 in.)

3

Values are in Metric units. Values in parentheses are English equivalents.

5

Lubricate threads with engine oil prior to assembly.

8 24 690 34 Rev. DKohlerEngines.com

Specifi cations

CLEARANCE SPECIFICATIONS

3

CH682 CH732 CH742 CH752

Crankshaft

End Play (free) 0.070/0.590 mm (0.0028/0.0230 in.)
End Play (w/thrust bearing components) 0.070/1.190 mm (0.0028/0.0468 in.)
Bore (in crankcase)

New
Max. Wear Limit

40.965/41.003 mm (1.6128/1.6143 in.)

41.016 mm (1.6148 in.)

Crankshaft to Sleeve Bearing (crankcase)
Running Clearance-New 0.03/0.09 mm (0.0012/0.0035 in.)

Bore (in closure plate)
New 40.987/40.974 mm (1.6136/1.6131 in.)

Crankshaft Bore (in closure plate)-to-Crankshaft
Running Clearance-New 0.039/0.074 mm (0.0015/0.0029 in.)

Flywheel End Main Bearing Journal
O.D. - New
O.D. - Max. Wear Limit
Max. Taper
Max. Out-of-Round

40.913/40.935 mm (1.6107/1.6116 in.)

40.84 mm (1.608 in.)

0.022 mm (0.0009 in.)

0.025 mm (0.0010 in.)

Closure Plate End Main Bearing Journal
O.D. - New
O.D. - Max. Wear Limit
Max. Taper
Max. Out-of-Round

40.913/40.935 mm (1.6107/1.6116 in.)

40.84 mm (1.608 in.)

0.022 mm (0.0009 in.)

0.025 mm (0.0010 in.)
Crankshaft (continued)
Connecting Rod Journal

O.D. - New
O.D. - Max. Wear Limit
Max. Taper
Max. Out-of-Round

35.955/35.973 mm (1.4156/1.4163 in.)

35.94 mm (1.415 in.)

0.018 mm (0.0007 in.)

0.025 mm (0.0010 in.)
T.I.R.

PTO End, Crank in Engine
Entire Crank, in V-Blocks

0.279 mm (0.0110 in.)

0.10 mm (0.0039 in.)

Cylinder Bore

Bore I.D.
New 80.000/

80.025 mm

82.988/83.013 mm

(3.2672/3.2682 in.)

(3.1496/

3.1506 in.)

Max. Wear Limit 80.065 mm

(3.1522 in.)

83.051 mm

(3.2697 in.)
Max. Out-of-Round 0.12 mm (0.0047 in.)
Max. Taper 0.05 mm (0.0020 in.)

Cylinder Head

Max. Out-of-Flatness 0.076 mm

0.1 mm (0.004 in.)

(0.003 in.)

3

Values are in Metric units. Values in parentheses are English equivalents.

924 690 34 Rev. D KohlerEngines.com

Specifi cations

CLEARANCE SPECIFICATIONS

3

CH682 CH732 CH742 CH752

Governor

Governor Cross Shaft-to-Crankcase
Running Clearancet 0.025/0.126 mm (0.0009/0.0049 in.)

Cross Shaft O.D.
New
Max. Wear Limit

Governor Gear Shaft-to-Governor Gear

7.949/8.000 mm (0.3129/0.3149 in.)

7.936 mm (0.3124 in.)

0.015/0.140 mm (0.0006/0.0055 in.)

Running Clearance
Gear Shaft O.D.

New
Max. Wear Limit

5.990/6.000 mm (0.2358/0.2362 in.)

5.977 mm (0.2353 in.)

Ignition

Spark Plug Gap 0.76 mm (0.030 in.)
Module Air Gap 0.203/0.305 mm (0.008/0.012 in.)

Piston, Piston Rings, and Piston Pin
Piston-to-Piston Pin Running Clearance 0.006/0.017 mm (0.0002/0.0007 in.)
Pin Bore I.D.

New
Max. Wear Limit

17.006/17.012 mm (0.6695/0.6698 in.)

17.025 mm (0.6703 in.)

Pin O.D.
New
Max. Wear Limit

16.995/17.000 mm (0.6691/0.6693 in.)

16.994 mm (0.6691 in.)
Top Compression Ring-to-Groove Side Clearance 0.030/0.070 mm (0.001/0.0026 in.)
Middle Compression Ring-to-Groove Side Clearance 00.030/0.070 mm (0.001/0.0026 in.)
Oil Control Ring-to-Groove Side Clearance 0.060/0.190 mm (0.0022/0.0073 in.)
Top Compression Ring End Gap

New Bore 0.100/

0.279 mm

0.189/0.277 mm

(0.0074/0.0109 in.)

(0.0039/

0.0110 in.)

Used Bore (Max) 0.490 mm

0.531 mm (0.0209 in.)

(0.0192 in.)

Middle Compression Ring End Gap
New Bore 1.400/

1.679 mm

1.519/1.797 mm

(0.0598/0.0708 in.)

(0.0551/

0.0661 in.)

Used Bore (Max) 1.941 mm

2.051 mm (0.0808 in.)

(0.0764 in.)

Thrust Face O.D.
New 79.966 mm

(3.1483 in.)

Max. Wear Limit 79.821 mm

(3.1426 in.)

8

8

82.978 mm (3.2668 in.)

82.833 mm (3.2611 in.)

Piston Thrust Face-to-Cylinder Bore Running
Clearance
New

0.025/

0.068 mm
(0.0010/

0.0027 in.)

0.019/0.062 mm (0.0007/0.0024 in.)

8

7

7

7

3

Values are in Metric units. Values in parentheses are English equivalents.

7

Measure 6 mm (0.2362 in.) above bottom of piston skirt at right angles to piston pin.

8

Measure 13 mm (0.5118 in.) above bottom of piston skirt at right angles to piston pin.

10 24 690 34 Rev. DKohlerEngines.com

Specifi cations

CLEARANCE SPECIFICATIONS

3

CH682 CH732 CH742 CH752

Valves and Valve Lifters

Hydraulic Valve Lifter to Crankcase Running Clearance 0.0241/0.0501 mm (0.0009/0.0020 in.)
Intake Valve Stem-to-Valve Guide Running Clearance 0.038/0.076 mm (0.0015/0.0030 in.)
Exhaust Valve Stem-to-Valve Guide Running Clearance 0.050/0.088 mm (0.0020/0.0035 in.)
Intake Valve Guide I.D.

New
Max. Wear Limit

7.038/7.058 mm (0.2771/0.2779 in.)

7.134 mm (0.2809 in.)

Exhaust Valve Guide I.D.
New
Max. Wear Limit

7.038/7.058 mm (0.2771/0.2779 in.)

7.159 mm (0.2819 in.)

Valve Guide Reamer Size
Standard

0.25 mm O.S

7.048 mm (0.2775 in.)

7.298 mm (0.2873 in.)
Intake Valve Minimum Lift 8.07 mm (0.3177 in.)
Exhaust Valve Minimum Lift 8.07 mm (0.3177 in.)
Nominal Valve Seat Angle 45°

3

Values are in Metric units. Values in parentheses are English equivalents.

1124 690 34 Rev. D KohlerEngines.com

Specifi cations

GENERAL TORQUE VALUES

English Fastener Torque Recommendations for Standard Applications

Bolts, Screws, Nuts and Fasteners Assembled Into Cast Iron or Steel

Size Grade 2 Grade 5 Grade 8

Tightening Torque: N·m (in. lb.) ± 20%

8-32 2.3 (20) 2.8 (25) — 2.3 (20)
10-24 3.6 (32) 4.5 (40) — 3.6 (32)
10-32 3.6 (32) 4.5 (40) — —

1/4-20 7.9 (70) 13.0 (115) 18.7 (165) 7.9 (70)

1/4-28 9.6 (85) 15.8 (140) 22.6 (200) —
5/16-18 17.0 (150) 28.3 (250) 39.6 (350) 17.0 (150)
5/16-24 18.7 (165) 30.5 (270) — —

3/8-16 29.4 (260) — — —

3/8-24 33.9 (300) — — —

Tightening Torque: N·m (ft. lb.) ± 20%

5/16-24 — — 40.7 (30) —

3/8-16 — 47.5 (35) 67.8 (50) —

3/8-24 — 54.2 (40) 81.4 (60) —
7/16-14 47.5 (35) 74.6 (55) 108.5 (80) —
7/16-20 61.0 (45) 101.7 (75) 142.5 (105) —

1/2-13 67.8 (50) 108.5 (80) 155.9 (115) —

1/2-20 94.9 (70) 142.4 (105) 223.7 (165) —
9/16-12 101.7 (75) 169.5 (125) 237.3 (175) —
9/16-18 135.6 (100) 223.7 (165) 311.9 (230) —

5/8-11 149.5 (110) 244.1 (180) 352.6 (260) —

5/8-18 189.8 (140) 311.9 (230) 447.5 (330) —

3/4-10 199.3 (147) 332.2 (245) 474.6 (350) —

3/4-16 271.2 (200) 440.7 (325) 637.3 (470) —

Grade 2 or 5 Fasteners

Into Aluminum

Metric Fastener Torque Recommendations for Standard Applications

Size

4.8

5.8

Tightening Torque: N·m (in. lb.) ± 10%

M4 1.2 (11) 1.7 (15) 2.9 (26) 4.1 (36) 5.0 (44) 2.0 (18)
M5 2.5 (22) 3.2 (28) 5.8 (51) 8.1 (72) 9.7 (86) 4.0 (35)
M6 4.3 (38) 5.7 (50) 9.9 (88) 14.0 (124) 16.5 (146) 6.8 (60)
M8 10.5 (93) 13.6 (120) 24.4 (216) 33.9 (300) 40.7 (360) 17.0 (150)

Tightening Torque: N·m (ft. lb.) ± 10%

M10 21.7 (16) 27.1 (20) 47.5 (35) 66.4 (49) 81.4 (60) 33.9 (25)
M12 36.6 (27) 47.5 (35) 82.7 (61) 116.6 (86) 139.7 (103) 61.0 (45)
M14 58.3 (43) 76.4 (56) 131.5 (97) 184.4 (136) 219.7 (162) 94.9 (70)

12 24 690 34 Rev. DKohlerEngines.com

Property Class

8.8

10.9 12.9

Torque Conversions

N·m = in. lb. x 0.113 in. lb. = N·m x 8.85

N·m = ft. lb. x 1.356 ft. lb. = N·m x 0.737

Noncritical

Fasteners

Into Aluminum

Tools and Aids

Certain quality tools are designed to help you perform specifi c disassembly, repair, and reassembly procedures. By
using these tools, you can properly service engines easier, faster, and safer! In addition, you’ll increase your service
capabilities and customer satisfaction by decreasing engine downtime.

Here is a list of tools and their source.

SEPARATE TOOL SUPPLIERS

Kohler Tools
Contact your local Kohler source of
supply.

TOOLS

Description Source/Part No.

Alcohol Content Tester

For testing alcohol content (%) in reformulated/oxygenated fuels.

Camshaft Endplay Plate

For checking camshaft endplay.

Camshaft Seal Protector (Aegis)

For protecting seal during camshaft installation.

Cylinder Leakdown Tester

For checking combustion retention and if cylinder, piston, rings, or valves are worn.
Individual component available:
Adapter 12 mm x 14 mm (Required for leakdown test on XT-6 engines)

Dealer Tool Kit (Domestic)

Complete kit of Kohler required tools.
Components of 25 761 39-S
Ignition System Tester
Cylinder Leakdown Tester
Oil Pressure Test Kit
Rectifi er-Regulator Tester (120 V AC/60Hz)

Dealer Tool Kit (International)

Complete kit of Kohler required tools.
Components of 25 761 42-S
Ignition System Tester
Cylinder Leakdown Tester
Oil Pressure Test Kit
Rectifi er-Regulator Tester (240 V AC/50Hz)

Digital Vacuum/Pressure Tester

For checking crankcase vacuum.
Individual component available:
Rubber Adapter Plug

Electronic Fuel Injection (EFI) Diagnostic Software

For Laptop or Desktop PC.

EFI Service Kit

For troubleshooting and setting up an EFI engine.
Components of 24 761 01-S
Fuel Pressure Tester
Noid Light
90° Adapter
Code Plug, Red Wire
Code Plug, Blue Wire
Shrader Valve Adapter Hose
Wire Probe Set (2 pieces regular wire with clip; 1 piece fused wire)
Hose Removal Tool, Dual Size/End (also sold as individual Kohler tool)

Flywheel Puller

For properly removing fl ywheel from engine.

SE Tools
415 Howard St.
Lapeer, MI 48446
Phone [phone]
Toll Free 800-664-2981
Fax [phone]

Design Technology Inc.
768 Burr Oak Drive
Westmont, IL 60559
Phone [phone]
Fax [phone]

Kohler 25 455 11-S

SE Tools KLR-82405

SE Tools KLR-82417

Kohler 25 761 05-S

Design Technology Inc.

DTI-731-03

Kohler 25 761 39-S

Kohler 25 455 01-S
Kohler 25 761 05-S
Kohler 25 761 06-S
Kohler 25 761 20-S

Kohler 25 761 42-S

Kohler 25 455 01-S
Kohler 25 761 05-S
Kohler 25 761 06-S
Kohler 25 761 41-S

Design Technology Inc.

DTI-721-01

Design Technology Inc.

DTI-721-10

Kohler 25 761 23-S

Kohler 24 761 01-S

Design Technology Inc.

DTI-019
DTI-021
DTI-023
DTI-027
DTI-029
DTI-037
DTI-031
DTI-033

SE Tools KLR-82408

1324 690 34 Rev. D KohlerEngines.com

Tools and Aids

TOOLS

Description Source/Part No.

Hose Removal Tool, Dual Size/End (also available in EFI Service Kit)

Used to properly remove fuel hose from engine components.

Hydraulic Valve Lifter Tool

For removing and installing hydraulic lifters.

Ignition System Tester

For testing output on all systems, including CD.

Inductive Tachometer (Digital)

For checking operating speed (RPM) of an engine.

Offset Wrench (K and M Series)

For removing and reinstalling cylinder barrel retaining nuts.

Oil Pressure Test Kit

For testing/verifying oil pressure on pressure lubricated engines.

Rectifi er-Regulator Tester (120 volt current)
Rectifi er-Regulator Tester (240 volt current)

For testing rectifi er-regulators.
Components of 25 761 20-S and 25 761 41-S
CS-PRO Regulator Test Harness
Special Regulator Test Harness with Diode

Spark Advance Module (SAM) Tester

For testing SAM (ASAM and DSAM) on engines with SMART-SPARK

.

™

Starter Servicing Kit (All Starters)

For removing and reinstalling drive retaining rings and brushes.
Individual component available:
Starter Brush Holding Tool (Solenoid Shift)

Triad/OHC Timing Tool Set

For holding cam gears and crankshaft in timed position while installing timing belt.

Valve Guide Reamer (K and M Series)

For properly sizing valve guides after installation.

Valve Guide Reamer O.S. (Command Series)

For reaming worn valve guides to accept replacement oversize valves. Can be used
in low-speed drill press or with handle below for hand reaming.

Reamer Handle

For hand reaming using Kohler 25 455 12-S reamer.

Kohler 25 455 20-S

Kohler 25 761 38-S

Kohler 25 455 01-S

Design Technology Inc.

DTI-110

Kohler 52 455 04-S

Kohler 25 761 06-S

Kohler 25 761 20-S
Kohler 25 761 41-S

Design Technology Inc.

DTI-031R
DTI-033R

Kohler 25 761 40-S

SE Tools KLR-82411

SE Tools KLR-82416

Kohler 28 761 01-S

Design Technology Inc.

DTI-K828

Kohler 25 455 12-S

Design Technology Inc.

DTI-K830

AIDS
Description Source/Part No.

Camshaft Lubricant (Valspar ZZ613) Kohler 25 357 14-S
Dielectric Grease (GE/Novaguard G661) Kohler 25 357 11-S
Dielectric Grease Loctite

®

51360

Kohler Electric Starter Drive Lubricant (Inertia Drive) Kohler 52 357 01-S
Kohler Electric Starter Drive Lubricant (Solenoid Shift) Kohler 52 357 02-S
RTV Silicone Sealant

Loctite
Only oxime-based, oil resistant RTV sealants, such as those listed, are approved

®

5900® Heavy Body in 4 oz. aerosol dispenser.

for use. Permatex® the Right Stuff® 1 Minute Gasket™ or Loctite® Nos. 5900® or
5910® are recommended for best sealing characteristics.

Kohler 25 597 07-S

Loctite® 5910

®

Loctite® Ultra Black 598™

Loctite® Ultra Blue 587™
Loctite® Ultra Copper 5920™
Permatex® the Right Stuff® 1

Minute Gasket™

Spline Drive Lubricant Kohler 25 357 12-S

14 24 690 34 Rev. DKohlerEngines.com

Tools and Aids

FLYWHEEL HOLDING TOOL ROCKER ARM/CRANKSHAFT TOOL

A fl ywheel holding tool can be made out of an old junk
fl ywheel ring gear and used in place of a strap wrench.

1. Using an abrasive cut-off wheel, cut out a six tooth
segment of ring gear as shown.

2. Grind off any burrs or sharp edges.

3. Invert segment and place it between ignition bosses
on crankcase so tool teeth engage fl ywheel ring
gear teeth. Bosses will lock tool and fl ywheel in
position for loosening, tightening, or removing with a
puller.

A spanner wrench to lift rocker arms or turn crankshaft
may be made out of an old junk connecting rod.

1. Find a used connecting rod from a 10 HP or larger
engine. Remove and discard rod cap.

2. Remove studs of a Posi-Lock rod or grind off
aligning steps of a Command rod, so joint surface is
fl at.

3. Find a 1 in. long capscrew with correct thread size to
match threads in connecting rod.

4. Use a fl at washer with correct I.D. to slip on
capscrew and approximately 1 in. O.D. Assemble
capscrew and washer to joint surface of rod.

1524 690 34 Rev. D KohlerEngines.com

Troubleshooting

TROUBLESHOOTING GUIDE

When troubles occur, be sure to check simple causes which, at fi rst, may seem too obvious to be considered. For
example, a starting problem could be caused by an empty fuel tank.

Some general common causes of engine troubles are listed below and vary by engine specifi cation. Use these to
locate causing factors.

Engine Cranks But Will Not Start

● Battery connected backwards.

● Blown fuse.

● Carburetor solenoid malfunction.

● Choke not closing.

● Clogged fuel line or fuel fi lter.

● Diode in wiring harness failed in open circuit mode.

● DSAI or DSAM malfunction.

● Empty fuel tank.

● Faulty electronic control unit.

● Faulty ignition coil(s).

● Faulty spark plug(s).

● Fuel pump malfunction-vacuum hose clogged or

leaking.

● Fuel shut-off valve closed.

● Ignition module(s) faulty or improperly gapped.

● Insuffi cient voltage to electronic control unit.

● Interlock switch is engaged or faulty.

● Key switch or kill switch in OFF position.

● Low oil level.

● Quality of fuel (dirt, water, stale, mixture).

● SMART-SPARKTM malfunction.

● Spark plug lead(s) disconnected.

Engine Starts But Does Not Keep Running

● Faulty carburetor.

● Faulty cylinder head gasket.

● Faulty or misadjusted choke or throttle controls.

● Fuel pump malfunction-vacuum hose clogged or

leaking.

● Intake system leak.

● Loose wires or connections that intermittently ground

ignition kill circuit.

● Quality of fuel (dirt, water, stale, mixture).

● Restricted fuel tank cap vent.

Engine Starts Hard

● Clogged fuel line or fuel fi lter.

● Engine overheated.

● Faulty ACR mechanism.

● Faulty or misadjusted choke or throttle controls.

● Faulty spark plug(s).

● Flywheel key sheared.

● Fuel pump malfunction-vacuum hose clogged or

leaking.

● Interlock switch is engaged or faulty.

● Loose wires or connections that intermittently ground

ignition kill circuit.

● Low compression.

● Quality of fuel (dirt, water, stale, mixture).

● Weak spark.

Engine Will Not Crank

● Battery is discharged.

● Faulty electric starter or solenoid.

● Faulty key switch or ignition switch.

● Interlock switch is engaged or faulty.

● Loose wires or connections that intermittently ground

ignition kill circuit.

● Pawls not engaging in drive cup.

● Seized internal engine components.

Engine Runs But Misses

● Carburetor adjusted incorrectly.

● Engine overheated.

● Faulty spark plug(s).

● Ignition module(s) faulty or improperly gapped.

● Incorrect crankshaft position sensor air gap.

● Interlock switch is engaged or faulty.

● Loose wires or connections that intermittently ground

ignition kill circuit.

● Quality of fuel (dirt, water, stale, mixture).

● Spark plug lead(s) disconnected.

● Spark plug lead boot loose on plug.

● Spark plug lead loose.

Engine Will Not Idle

● Engine overheated.

● Faulty spark plug(s).

● Idle fuel adjusting needle(s) improperly set.

● Idle speed adjusting screw improperly set.

● Inadequate fuel supply.

● Low compression.

● Quality of fuel (dirt, water, stale, mixture).

● Restricted fuel tank cap vent.

Engine Overheats

● Cooling fan broken.

● Excessive engine load.

● Fan belt failed/off.

● Faulty carburetor.

● High crankcase oil level.

● Lean fuel mixture.

● Low cooling system fl uid level.

● Low crankcase oil level.

● Radiator, and/or cooling system components clogged,

restricted, or leaking.

● Water pump belt failed/broken.

● Water pump malfunction.

Engine Knocks

● Excessive engine load.

● Hydraulic lifter malfunction.

● Incorrect oil viscosity/type.

● Internal wear or damage.

● Low crankcase oil level.

● Quality of fuel (dirt, water, stale, mixture).

16 24 690 34 Rev. DKohlerEngines.com

Troubleshooting

Engine Loses Power

● Dirty air cleaner element.

● Engine overheated.

● Excessive engine load.

● Restricted exhaust.

● Faulty spark plug(s).

● High crankcase oil level.

● Incorrect governor setting.

● Low battery.

● Low compression.

● Low crankcase oil level.

● Quality of fuel (dirt, water, stale, mixture).

Engine Uses Excessive Amount of Oil

● Loose or improperly torqued fasteners.

● Blown head gasket/overheated.

● Breather reed broken.

● Clogged, broken, or inoperative crankcase breather.

● Crankcase overfi lled.

● Incorrect oil viscosity/type.

● Worn cylinder bore.

● Worn or broken piston rings.

● Worn valve stems/valve guides.

Oil Leaks from Oil Seals, Gaskets

● Breather reed broken.

● Clogged, broken, or inoperative crankcase breather.

● Loose or improperly torqued fasteners.

● Piston blow by, or leaky valves.

● Restricted exhaust.

EXTERNAL ENGINE INSPECTION

NOTE: It is good practice to drain oil at a location away

from workbench. Be sure to allow ample time for
complete drainage.

Before cleaning or disassembling engine, make a
thorough inspection of its external appearance and
condition. This inspection can give clues to what
might be found inside engines (and cause) when it is
disassembled.

● Check for buildup of dirt and debris on crankcase,

cooling fi ns, grass screen, and other external surfaces.
Dirt or debris on these areas can cause overheating.

● Check for obvious fuel and oil leaks, and damaged

components. Excessive oil leakage can indicate a
clogged or inoperative breather, worn or damaged
seals or gaskets, or loose fasteners.

● Check air cleaner cover and base for damage or

indications of improper fi t and seal.

● Check air cleaner element. Look for holes, tears,

cracked or damaged sealing surfaces, or other
damage that could allow unfi ltered air into engine. A
dirty or clogged element could indicate insuffi cient or
improper maintenance.

● Check carburetor throat for dirt. Dirt in throat is further

indication that air cleaner was not functioning properly.

● Check if oil level is within operating range on dipstick.

If it is above, sniff for gasoline odor.

● Check condition of oil. Drain oil into a container; it

should fl ow freely. Check for metal chips and other
foreign particles.

Sludge is a natural by-product of combustion; a small

accumulation is normal. Excessive sludge formation
could indicate over rich fuel settings, weak ignition,
overextended oil change interval or wrong weight or
type of oil was used.

CLEANING ENGINE

WARNING

Cleaning Solvents can cause severe injury or
death.

Use only in well ventilated areas away from
ignition sources.

Carburetor cleaners and solvents are extremely
fl ammable. Follow cleaner manufacturer’s warnings
and instructions on its proper and safe use. Never use
gasoline as a cleaning agent.

After inspecting external condition of engine, clean
engine thoroughly before disassembly. Clean individual
components as engine is disassembled. Only clean
parts can be accurately inspected and gauged for wear
or damage. There are many commercially available
cleaners that will quickly remove grease, oil, and grime
from engine parts. When such a cleaner is used, follow
manufacturer’s instructions and safety precautions
carefully.

Make sure all traces of cleaner are removed before
engine is reassembled and placed into operation. Even
small amounts of these cleaners can quickly break down
lubricating properties of engine oil.

1724 690 34 Rev. D KohlerEngines.com

Troubleshooting

CRANKCASE VACUUM TEST

WARNING

Carbon Monoxide can cause severe nausea,
fainting or death.

Avoid inhaling exhaust fumes.

Engine exhaust gases contain poisonous carbon
monoxide. Carbon monoxide is odorless, colorless,
and can cause death if inhaled.

A partial vacuum should be present in crankcase when engine is operating. Pressure in crankcase (normally caused
by a clogged or improperly assembled breather) can cause oil to be forced out at oil seals, gaskets, or other available
spots.

Crankcase vacuum is best measured with either a water manometer or a vacuum gauge. Complete instructions are
provided in kits.

To test crankcase vacuum with manometer:

1. Insert rubber stopper into oil fi ll hole. Be sure pinch
clamp is installed on hose and use tapered adapters
to connect hose between stopper and one
manometer tube. Leave other tube open to
atmosphere. Check that water level in manometer is
at 0 line. Make sure pinch clamp is closed.

2. Start engine and run no-load high speed.

3. Open clamp and note water level in tube.

Level in engine side should be a minimum of 10.2

cm (4 in.) above level in open side.

If level in engine side is less than specifi ed (low/no

vacuum), or level in engine side is lower than level in
open side (pressure), check for conditions in table
below.

4. Close pinch clamp before stopping engine.

Keep hands, feet, hair, and clothing away from all
moving parts to prevent injury. Never operate engine
with covers, shrouds, or guards removed.

To test crankcase vacuum with vacuum/pressure gauge:

1. Remove dipstick or oil fi ll plug/cap.

2. Install adapter into oil fi ll//dipstick tube opening,

3. Run engine and observe gauge reading.
Analog tester–needle movement to left of 0 is a

Digital tester–depress test button on top of tester.
Crankcase vacuum should be a minimum of 10.2 cm

Rotating Parts can cause severe injury.
Stay away while engine is in operation.

upside down over end of a small diameter dipstick
tube, or directly into engine if a tube is not used.
Insert barbed gauge fi tting into hole in stopper.

vacuum, and movement to right indicates a pressure.

(4 in.) of water. If reading is below specifi cation, or if
pressure is present, check table below for possible
causes and conclusions.

WARNING

Condition Conclusion

Crankcase breather clogged or inoperative. NOTE: If breather is integral part of valve cover and

cannot be serviced separately, replace valve
cover and recheck pressure.

Disassemble breather, clean parts thoroughly, check
sealing surfaces for fl atness, reassemble, and recheck
pressure.

Seals and/or gaskets leaking. Loose or improperly torque
fasteners.

Piston blow by or leaky valves (confi rm by inspecting
components).

Restricted exhaust. Check exhaust screen/spark arrestor (if equipped). Clean

Replace all worn or damaged seals and gaskets. Make
sure all fasteners are tightened securely. Use appropriate
torque valves and sequences when necessary.

Recondition piston, rings, cylinder bore, valves and
valves guides.

or replace as needed. Repair or replace any other
damaged/restricted muffl er or exhaust system parts.

18 24 690 34 Rev. DKohlerEngines.com

Troubleshooting

COMPRESSION TEST

For Command Twins:
A compression test is best performed on a warm engine. Clean any dirt or debris away from base of spark plug(s)

before removing them. Be sure choke is off, and throttle is wide open during test. Compression should be at least 160
psi and should not vary more than 15% between cylinders.

All other models:
These engines are equipped with an automatic compression release (ACR) mechanism. It is diffi cult to obtain an

accurate compression reading because of ACR mechanism. As an alternative, use cylinder leakdown test described
below.

CYLINDER LEAKDOWN TEST

A cylinder leakdown test can be a valuable alternative to a compression test. By pressurizing combustion chamber
from an external air source you can determine if valves or rings are leaking, and how badly.

Cylinder leakdown tester is a relatively simple, inexpensive leakdown tester for small engines. This tester includes a
quick-connect for attaching adapter hose and a holding tool.

1. Run engine for 3-5 minutes to warm it up.

2. Remove spark plug(s) and air fi lter from engine.

3. Rotate crankshaft until piston (of cylinder being tested) is at top dead center (TDC) of compression stroke. Hold

engine in this position while testing. Holding tool supplied with tester can be used if PTO end of crankshaft is
accessible. Lock holding tool onto crankshaft. Install a 3/8 in. breaker bar into hole/slot of holding tool, so it is
perpendicular to both holding tool and crankshaft PTO.

If fl ywheel end is more accessible, use a breaker bar and socket on fl ywheel nut/screw to hold it in position. An

assistant may be needed to hold breaker bar during testing. If engine is mounted in a piece of equipment, it may
be possible to hold it by clamping or wedging a driven component. Just be certain that engine cannot rotate off of
TDC in either direction.

4. Install adapter into spark plug hole, but do not attach it to tester at this time.

5. Turn regulator knob completely counterclockwise.

6. Connect an air source of at least 50 psi to tester.

7. Turn regulator knob clockwise (increase direction) until gauge needle is in yellow set area at low end of scale.

8. Connect tester quick-connect to adapter hose. While fi rmly holding engine at TDC, gradually open tester valve.

Note gauge reading and listen for escaping air at combustion air intake, exhaust outlet, and crankcase breather.

Condition Conclusion

Air escaping from crankcase breather. Ring or cylinder worn.
Air escaping from exhaust system. Defective exhaust valve/improper seating.
Air escaping from intake. Defective intake valve/improper seating.
Gauge reading in low (green) zone. Piston rings and cylinder in good condition.
Gauge reading in moderate (yellow) zone. Engine is still usable, but there is some wear present.

Customer should start planning for overhaul or
replacement.

Gauge reading in high (red) zone. Rings and/or cylinder have considerable wear. Engine

should be reconditioned or replaced.

1924 690 34 Rev. D KohlerEngines.com

Air Cleaner/Intake

AIR CLEANER

These systems are CARB/EPA certifi ed and components
should not be altered or modifi ed in any way.

Air Cleaner Components

G

B

A Air Cleaner Housing B End Cap
C Element D Inner Element
E Ejector Area F Inlet Screen
G Retaining Clip H Filter Minder

NOTE: Operating engine with loose or damaged air

cleaner components could cause premature
wear and failure. Replace all bent or damaged
components.

NOTE: Paper element cannot be blown out with

compressed air.

C

E

D

F

A

H

1. Unhook retaining clips and remove end cap(s).

2. Check and clean inlet screen (if equipped).

3. Pull air cleaner element out of housing and replace.
Check condition of inner element; replace when dirty.

4. Check all parts for wear, cracks, or damage, and that
ejector area is clean.

5. Install new element(s).

6. Reinstall end cap(s) with dust ejector valve/screen
down; secure with retaining clips.

BREATHER TUBE

Ensure both ends of breather tube are properly
connected.

AIR COOLING

WARNING

Hot Parts can cause severe burns.
Do not touch engine while operating or just

after stopping.

Never operate engine with heat shields or guards
removed.

Proper cooling is essential. To prevent over heating,
clean screens, cooling fi ns, and other external surfaces
of engine. Avoid spraying water at wiring harness or any
electrical components. Refer to Maintenance Schedule.

24 690 34 Rev. DKohlerEngines.com20

Fuel System

Typical carbureted fuel system and related components
include:

● Fuel tank and valve.

● Fuel lines.

● In-line fuel fi lter.

● Fuel pump.

● Carburetor.

Fuel from tank is moved through in-line fi lter and fuel
lines by fuel pump. Fuel then enters carburetor fl oat bowl
and is drawn into carburetor body and mixed with air.
This fuel-air mixture is then burned in engine combustion
chamber.

FUEL RECOMMENDATIONS

Refer to Maintenance.

FUEL LINE

Low permeation fuel line must be installed on carbureted
Kohler Co. engines to maintain EPA and CARB
regulatory compliance.

FUEL PUMP

These engines use either a mechanical pump or a pulse
style fuel pump. Pumping action of pulse style pumps is
created by oscillation of positive and negative pressures
within crankcase. This pressure is transmitted to pulse
pump through rubber hose connected between pump
and crankcase. Pumping action causes diaphragm on
inside of pump to pull fuel in on its downward stroke
and to push it into carburetor on its upward stroke. Two
check valves prevent fuel from going backward through
pump.

Performance

Minimum fuel delivery rate must be 7.5 L/hr. (2 gal./
hr.) with a pressure at 0.3 psi and a fuel lift of 24 in. A

1.3 L/hr. (0.34 gal./hr.) fuel rate must be maintained at
5 Hz.

Fuel Pump Replacement

Pulse Fuel Pump

NOTE: Make sure orientation of new pump is consistent

with removed pump. Internal damage may occur
if installed incorrectly.

To replace pulse pump follow these steps. Note
orientation of pump before removing.

1. Disconnect fuel lines from inlet, outlet, and pulse

fi ttings on fuel pump.

2. Remove screws and take off pump.

3. Connect pulse line to new fuel pump and make sure

opposite end is properly connected to fi tting on
crankcase.

4. Attach new fuel pump using screws. Torque screws

to 2.3 N·m (20 in. lb.).

5. Reconnect fuel lines to inlet and outlet fi ttings and

secure with clamps.

Mechanical Pump

Mechanical fuel pump is an integral part of valve cover
assembly and not serviced separately.

1. Disconnect fuel lines from inlet and outlet fi ttings.

Note orientation.

2. Follow procedure for replacing valve cover. Refer to

Disassembly and Reassembly.

3. Reconnect fuel lines to inlet and outlet fi ttings and

secure with clamps.

FUEL SYSTEM TESTS

When engine starts hard or turns over but will not start, fuel system might be causing problems. Test fuel system by
performing following test.

1. Check for fuel in combustion chamber.
a. Disconnect and ground spark plug leads.
b. Close choke on carburetor.
c. Crank engine several times.
d. Remove spark plug and check for fuel at tip.

Condition Conclusion

Fuel at tip of spark plug. Fuel is reaching combustion chamber.
No fuel at tip of spark plug. Check fuel fl ow from fuel tank (step 2).
Fuel fl ows from fuel line. Check for faulty fuel pump (step 3).

No fuel fl ow from fuel line. Check fuel tank cap vent, fuel pickup screen, in-line

Fuel line condition. Check for a clogged fuel line. If fuel line is unobstructed,

2. Check for fuel fl ow from tank to fuel pump.
a. Remove fuel line from inlet fi tting of fuel pump.
b. Hold line below bottom of tank. Open shut-off

valve (if equipped) and observe fl ow.

3. Check operation of fuel pump.
a. Remove fuel line from inlet fi tting of carburetor.
b. Crank engine several times and observe fl ow.

If fuel pump is working, check for faulty carburetor. Refer
to Carburetor.

fi lter, shut-off valve, and fuel line. Correct any observed
problem and reconnect line.

check for overfi lled crankcase and/or oil in pulse line. If
checks don't reveal cause of problem, replace pump.

2124 690 34 Rev. D KohlerEngines.com

Fuel System

CARBURETOR

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

Walbro Two-Barrel Carburetor Components

V

T

U

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings, away
from sparks or fl ames. Spilled fuel could ignite if it comes
in contact with hot parts or sparks from ignition. Never use
gasoline as a cleaning agent.

W

X

A

R

S

Q

C

D

B

E

Carburetor Body

A

Subassembly

Main Nozzle-

F

K

P

U Choke Shaft V

Left Side

Accelerator

Pump Cover

Screws

Main Nozzle-

Right Side

P

O

N

M

L

K

B Vacuum Hose C

G

L

Q Float Pin R Idle Spring S

Slow Jet-

Left Side

Accelerator

Pump Cover

Idle Speed

Screw

Float Valve/Inlet

Needle

H Bowl Screw I Fuel Solenoid J Solenoid Gasket

M Spring N Diaphragm O

Choke Plate

W

Screw

F

G

H

J

I

D Float E Bowl Gasket

Slow Jet-

Right Side

Plastic Dust Seal

Cover

X Choke Plate

T Choke Spring

22 24 690 34 Rev. DKohlerEngines.com

Fuel System

Engines in this series are equipped with a two-barrel side-draft carburetor with fi xed main jets on a matching intake
manifold. Carburetor features a self-relieving choke, serviceable slow jets, main jets, accelerator pump, and a fuel
shutdown solenoid.

Troubleshooting Checklist

When engine starts hard, runs roughly or stalls at low
idle speed, check following areas before adjusting or
disassembling carburetor.

1. Make sure fuel tank is fi lled with clean, fresh
gasoline.

2. Make sure fuel tank cap vent is not blocked and that
it is operating properly.

3. Make sure fuel is reaching carburetor. This includes
checking fuel shut-off valve, fuel tank fi lter screen,
in-line fuel fi lter, fuel lines and fuel pump for
restrictions or faulty components as necessary.

Troubleshooting-Carburetor Related Causes

Condition Possible Cause Conclusion

Engine starts hard, runs rough, or
stalls at idle speed.

Engine runs rich (indicated by black,
sooty exhaust smoke, misfi ring, loss
of speed and power, governor
hunting, or excessive throttle
opening).

Engine runs lean (indicated by
misfi ring, loss of speed and power,
governor hunting, or excessive
throttle opening).

Fuel leaks from carburetor. Float level is set too high. Adjust fl oat according to Float

Low idle speed improperly adjusted. Adjust low idle speed tab.

Clogged air cleaner. Clean or replace air cleaner.
Choke partially closed during

operation.
Float level is set too high. Adjust fl oat according to Float

Dirt under fuel inlet needle. Remove needle; clean needle and

Bowl vent or air bleeds plugged. Remove low idle fuel adjusting

Float level is set too low. Adjust fl oat according to Float

Idle holes plugged; dirt in fuel delivery
channels.

Dirt under fuel inlet needle. Remove needle; clean needle and

Bowl vents plugged. Blow out with compressed air.
Carburetor bowl gasket leaks. Replace gasket.

4. Make sure air cleaner base and carburetor are
securely fastened to engine using gaskets in good
condition.

5. Make sure air cleaner element (including precleaner
if equipped) is clean and all air cleaner components
are fastened securely.

6. Make sure ignition system, governor system,
exhaust system, and throttle and choke controls are
operating properly.

Check choke lever/linkage to ensure
choke is operating properly.

Replacement Procedure.

seat and blow with compressed air.

needle. Clean vent, ports, and air
bleeds. Blow out all passages with
compressed air.

Replacement Procedure.
Remove low idle fuel adjusting

needle. Clean main fuel jet and all
passages; blow out with compressed
air.

Replacement Procedure.

seat and blow with compressed air.

2324 690 34 Rev. D KohlerEngines.com

Fuel System

Fuel Shut-Off Solenoid

Carburetors are equipped with a fuel shut-off solenoid.
Solenoid is attached to fuel bowl. Solenoid has a spring­loaded pin that retracts when 12 volts is applied to lead,
allowing fuel flow to main jet. When current is removed,
pin extends blocking fuel flow.

Below is a simple test, performed with engine off, that
can determine if solenoid is functioning properly.

1. Shut off fuel and remove solenoid from carburetor.
When solenoid is loosened and removed, gas will
leak out of carburetor. Have a container ready to
catch fuel.

2. Wipe tip of solenoid with a shop towel or blow with
compressed air to remove any remaining fuel. Take
solenoid to a location with good ventilation and no
fuel vapors present. You will also need a 12 volt
power source that can be switched on and off.

3. Be sure power source is switched OFF. Connect
positive power source lead to red lead of solenoid.
Connect negative power source lead to solenoid
body.

4. Turn power source ON and observe pin in center of
solenoid. Pin should retract with power ON and
return to its original position with power OFF. Test
several times to verify operation.

Carburetor Circuits

Float

Fuel level in bowl is maintained by fl oat and fuel inlet
needle. Buoyant force of fl oat stops fuel fl ow when
engine is at rest. When fuel is being consumed, fl oat will
drop and fuel pressure will push inlet needle away from
seat, allowing more fuel to enter bowl. When demand
ceases, buoyant force of fl oat will again overcome fuel
pressure, rising to predetermined setting and stop fl ow.

Slow and Mid-Range

At low speeds engine operates only on slow circuit.
As a metered amount of air is drawn through slow air
bleed jets, fuel is drawn through 2 main jets and further
metered through slow jets. Air and fuel are mixed in body
of slow jet and exit to transfer port. From transfer port,
air fuel mixture is delivered to idle progression chamber.
From idle progression chamber, air fuel mixture is
metered through idle port passages. At low idle when
vacuum signal is weak, air/fuel mixture is controlled by
setting of idle fuel adjusting screws. This mixture is then
mixed with main body of air and delivered to engine.
As throttle plate opening increases, greater amounts of
air/fuel mixture are drawn in through fi xed and metered
idle progression holes. As throttle plate opens further,
vacuum signal becomes great enough so main circuit
begins to work.

Main (high-speed)

At high speeds/loads engine operates on main circuit.
As a metered amount of air is drawn through 4 air jets,
fuel is drawn through main jets. Air and fuel are mixed
in main nozzles then enters main body of airfl ow where
further mixing of fuel and air occurs. This mixture is then
delivered to combustion chamber. Carburetor has a fi xed
main circuit; no adjustment is possible.

Carburetor Adjustments

NOTE: Carburetor adjustments should be made only

after engine has warmed up.

Carburetor is designed to deliver correct fuel-to-air
mixture to engine under all operating conditions. Main
fuel jet is calibrated at factory and is not adjustable.
Idle fuel adjusting needles are also set at factory and
normally do not need adjustment.

Low Idle Speed (RPM) Adjustment

NOTE: Actual low idle speed depends on application.

Refer to equipment manufacturer’s
recommendations. Low idle speed for basic
engines is 1200 RPM.

Place throttle control into idle or slow position. Turn low
idle speed adjusting screw in or out to obtain allow idle
speed of 1200 RPM (± 75 RPM).

Governed Idle Speed Adjustment (If equipped)

1. Hold governor lever away from carburetor so throttle
lever is against idle speed (RPM) adjustment screw
of carburetor. Start engine and allow to warm up,
then adjust screw to set approximately 1200 RPM.
Check speed using a tachometer. Turn adjustment
screw (inner) clockwise (in) to increase or
counterclockwise (out) to decrease speed.

2. Release governor lever and check that throttle lever
is in idle position. Turn governed idle adjustment
screw to obtain equipment manufacturer’s
recommended idle speed (1500-1800 RPM). Some
engines have a bendable tab that is used to set this
speed. A pliers should be used to bend this tab to
achieve recommended speed. Governed idle speed
(RPM) is typically 300 RPM (approximate) higher
than low idle speed.

3. Move throttle lever to wide-open/full throttle position
and hold in this position. Turn high speed screw to
obtain intended high speed no-load RPM. Governed
idle speed must be set before making this
adjustment.

High Speed (RPM) Adjustment

1. With engine running, move throttle control to fast.

2. Turn inner adjustment screw outward to decrease, or
inward to increase RPM speed.

3. Stop when desired RPM speed is obtained.

24 24 690 34 Rev. DKohlerEngines.com

Fuel System

Carburetor Servicing

WARNING

Accidental Starts can cause severe injury or
death.

Disconnect and ground spark plug lead(s)
before servicing.

Before working on engine or equipment, disable
engine as follows: 1) Disconnect spark plug lead(s). 2)
Disconnect negative (–) battery cable from battery.

NOTE: Main and slow jets are fi xed and size specifi c

and can be removed if required. Fixed jets for
high altitudes are available.

NOTE: Keep solvent away from plastic or rubber parts if

non-compatible or damage may occur.

● Inspect carburetor body for cracks, holes, and other
wear or damage.

● Inspect fl oat for cracks, holes, and missing or
damaged fl oat tabs. Check fl oat hinge and shaft for
wear or damage.

● Inspect fuel inlet needle and seat for wear or damage.

● Inspect spring loaded choke plate to make sure it

moves freely on shaft.

Float Replacement/Overhaul/Choke Repair

Float Setting

A

C

B

A Top of Float Body (Carburetor Body Inverted)

B Top of Gasket Crush Ribs

1.6 mm (0.063 in.) +/- 0.5 mm (0.02 in.) Float

C

Setting

NOTE: Inlet needle center pin is spring loaded. Make

sure fl oat rests against fuel inlet needle without
depressing center pin.

If symptoms described in Troubleshooting-Carburetor
Related Causes indicate fl oat level problems, remove
carburetor from engine to check and/or replace fl oat.
Use a fl oat kit to replace fl oat, pin, fl oat valve.

1. Perform removal procedures for appropriate air
cleaner and carburetor outlined in Disassembly.

2. Clean exterior surfaces of dirt or foreign material
before disassembling carburetor. Disconnect
accelerator pump vacuum hose from bottom of bowl.
Remove screws and carefully separate fuel bowl
from carburetor. Transfer any remaining fuel into an
approved container. Discard bowl screws and
gasket; save other parts.

3. Remove fl oat pin, lift out fl oat and inlet needle;
discard parts. Seat for inlet needle is not serviceable
and should not be removed.

4. Use a 1/4" open end wrench and carefully remove
nozzle tubes from bowl. Note and mark jets by
location for proper reassembly. Main jets and main
nozzles may be size/side specifi c. Main jets are
pressed into bottom of main nozzle tubes and are
not serviced separately. Slow jets are located to
outside of nozzle tubes and are removed with a
narrow, straight blade screwdriver. Save parts for
cleaning and reuse.

5. Remove accelerator pump cover screws from
bottom of bowl while holding pump cover in place.
Accelerator pump spring will be pushing against
cover as it is directly under it. Remove and discard
spring and diaphragm. Solenoid can also be
removed using a 1/2" wrench and gasket discarded.

6. Carburetor is now disassembled for appropriate
cleaning and installation of parts in overhaul kit.
Further disassembly is not necessary. Throttle shaft
assembly, fuel inlet seat, idle fuel adjustment screws
are non-serviceable items and should not be
removed. Choke shaft assembly is serviceable,
however it should not be removed unless a choke
repair kit will be installed.

To install choke repair kit go to step 7, otherwise go

to step 14.

7. Clean areas around choke lever/shaft assembly and
self-relieving choke mechanism thoroughly.

8. Note position of spring hooks and choke plate for
correct reassembly later. Remove screws attaching
choke plate to choke shaft. Pull shaft out of
carburetor body, note preload of spring and discard
removed parts.

9. Clean I.D. of both choke shaft bores as required.

10. Install new spring, plastic dust seal cover, and dust
seal on shaft.

11. Slide choke shaft assembly into carburetor,
connecting spring hooks to levers. Before seating
choke shaft completely, lever needs to be rotated
clockwise slightly to get past stop. This preloads
choke plate for proper starting function.

12. Position and reinstall choke plate to fl at side of
choke shaft. Start screws. Close choke and check
plate alignment within carburetor throat, then tighten
screws securely. Do not overtighten.

13. Check for proper operation and free movement of
parts.

2524 690 34 Rev. D KohlerEngines.com

Fuel System

14. Clean carburetor body, main jets, vent ports, seats,
etc., using a good commercially available carburetor
solvent. Keep solvent away from plastic or rubber
parts if non-compatible or damage may occur. Use
clean, dry compressed air to blow out internal
channels and ports. Do not use metal tools or wire to
clean orifi ces and jets. Inspect and thoroughly check
carburetor for cracks, wear, or damage. Inspect fuel
inlet seat for wear or damage. Check spring loaded
choke plate to make sure it moves freely on shaft.

15. Clean carburetor fuel bowl as required, including
accelerator jet, feed hole, and check valve in bottom
of bowl.

16. Install new diaphragm assembly with outer lip resting
in groove of pump base. Install new spring on top of
diaphragm center plate. Reinstall cover and secure
with new screws. Torque screws to 1-1.4 N·m (8-12
in. lb.). Reinstall solenoid using new gasket and
torque solenoid to 3.4-5.6 N·m (30-50 in. lb.).

17. Reinstall main nozzles assemblies and slow jets in
their respective sides.

18. Attach new inlet needle into metal hinge of fl oat.
Groove near top of needle slides into formed fork.

19. Install fl oat and inlet needle down into seat and
carburetor body. With fl oat hinge held in between
body mounting legs, insert new pivot pin through
fl oat hinge and into opposite hole.

20. Invert carburetor body as shown and measure
dimension between top of fl oat and top of gasket
fl oat rib on body. Correct fl oat setting is 1.6 mm
(0.063 in.) ± 0.5 mm (0.02 in.).

21. If fl oat height adjustment is required, a small fl at
blade screwdriver can be used to pry tab up from
side, or pry tab down on end.

22. When proper fl oat height is obtained, carefully
reinstall fuel bowl, using new bowl gasket. Secure
with new screws. Torque screws to 2.3-2.7 N·m
(20-24 in. lb.).

23. Reattach accelerator pump vacuum hose.

24. Use new mounting gaskets for air cleaner and
carburetor. Reinstall carburetor and disassembled
components following Reassembly procedures.

25. Reconnect spark plug leads and negative battery
cable. Start engine and perform Low Idle Speed
Adjustment.

High Altitude Operation

Engines may require a high altitude carburetor kit to
ensure correct engine operation at altitudes above
1219 meters (4000 ft.). To obtain high altitude kit
information or to fi nd a Kohler authorized dealer visit
KohlerEngines.com or call1-800-544-2444 (U.S. and
Canada).

This engine should be operated in its original
confi guration below 1219 meters (4000 ft.) as damage
may occur if high altitude carburetor kit is installed and
operated below 1219 meters (4000 ft.).

26 24 690 34 Rev. DKohlerEngines.com

Governor System

GOVERNOR

Engine is equipped with a centrifugal fl yweight mechanical governor. It is designed to hold engine speed constant
under changing load conditions. Governor gear/fl yweight mechanism is mounted inside crankcase on closure plate,
and is driven off gear on camshaft.

Governor Components

J

I

K

D

H

Inside Engine

E

B

A

G

F

C

A Throttle Lever B Throttle Linkage C Governor Lever D Choke Linkage

E Governor Spring F Governed Idle Spring G Control Bracket H Regulating Pin

I Governor Gear J

This governor design works as follows:

● Centrifugal force acting on rotating governor gear assembly causes fl yweights to move outward as speed

increases. Governor spring tension moves them inward as speed decreases.

● As fl yweights move outward, they cause regulating pin to move outward.

● Regulating pin contacts tab on cross shaft causing shaft to rotate. One end of cross shaft protrudes through

crankcase. Rotating action of cross shaft is transmitted to throttle lever of carburetor through external linkage.

● When engine is at rest, and throttle is in FAST position, tension of governor spring holds throttle plate open. When

engine is operating, governor gear assembly is rotating. Force applied by regulating pin against cross shaft tends to
close throttle plate. Governor spring tension and force applied by regulating pin balance each other during
operation, to maintain engine speed.

● When load is applied and engine speed and governor gear speed decreases, governor spring tension moves

governor lever to open throttle plate wider. This allows more fuel into engine, increasing engine speed. As speed
reaches governed setting, governor spring tension and force applied by regulating pin will again offset each other to
hold a steady engine speed.

Governor Adjustments

NOTE: Do not tamper with governor setting. Overspeed is hazardous and could cause personal injury.

Initial Adjustment Procedure

Make this adjustment whenever governor arm is loosened or removed from cross shaft. Adjust as follows:

1. Make sure throttle linkage is connected to governor arm and throttle lever on carburetor.

2. Loosen nut holding governor lever to cross shaft.

3. Move governor lever toward carburetor as far as it will go (wide open throttle) and hold in this position.

4. Insert a long thin rod or tool into hole on cross shaft and rotate shaft counterclockwise (viewed from end) as far as

it will turn, then torque nut to 6.8 N·m (60 in. lb.).

Locking Tab Thrust

Washer

K Governor Gear Shaft

2724 690 34 Rev. D KohlerEngines.com

Governor System

Sensitivity Adjustment

Governor sensitivity is adjusted by repositioning
governor spring in holes of governor lever. If speed
surging occurs with a change in engine load, governor
is set too sensitive. If a big drop in speed occurs when
normal load is applied, governor should be set for
greater sensitivity and adjust as follows:

1. To increase sensitivity, move spring closer to
governor cross shaft.

2. To decrease sensitivity, move spring away from
governor cross shaft.

28 24 690 34 Rev. DKohlerEngines.com

Lubrication System

This engine uses a full pressure lubrication system which
delivers oil under pressure to crankshaft, camshaft,
connecting rod bearing surfaces, and hydraulic valve
lifters.

A high-effi ciency gerotor oil pump maintains high oil fl ow
and oil pressure, even at low speeds and high operating
temperatures. A pressure relief valve limits maximum
pressure of system. Closure plate must be removed to
service oil pickup, pressure relief valve, and oil pump.

Lubrication Components

B

A

C

G

F

D

E

A Dipstick B Oil Sentry

TM

C Oil Fill Cap D Oil Cooler

E Oil Filter F Oil Drain Plug

G Back Side

OIL RECOMMENDATIONS

Refer to Maintenance.

CHECK OIL LEVEL

NOTE: To prevent extensive engine wear or damage,

never run engine with oil level below or above
operating range indicator on dipstick.

Ensure engine is cool. Clean oil fi ll/dipstick areas of any
debris.

1. Remove dipstick; wipe oil off.

2. Reinsert dipstick into tube; press completely down.

3. Remove dipstick; check oil level. Level should be at

top of indicator on dipstick.

4. If oil is low on indicator, add oil up to top of indicator

mark.

5. Reinstall dipstick and tighten securely.

CHANGE OIL AND FILTER

Change oil while engine is warm.

1. Clean area around oil fi ll cap/dipstick, drain plug/oil
drain valve.

a. Remove drain plug and oil fi ll cap/dipstick. Allow

oil to drain completely.

or

b. Open oil drain valve cap; if needed, attach a

length of 1/2 in. I.D. hose to direct oil into
appropriate container; twist valve drain body
counterclockwise and pull. Remove dipstick.
Allow oil to drain completely.

2. Clean area around oil fi lter. Place a container under
fi lter to catch any oil and remove fi lter. Wipe off
mounting surface.

a. Reinstall drain plug. Torque to 13.6 N·m

(10 ft. lb. ).

or

b. Close oil drain valve body, remove hose (if used),

and replace cap.

3. Place new fi lter in shallow pan with open end up. Fill
with new oil until oil reaches bottom of threads. Allow
2 minutes for oil to be absorbed by fi lter material.

4. Apply a thin fi lm of clean oil to rubber gasket on new
fi lter.

5. Refer to instructions on oil fi lter for proper
installation.

6. Fill crankcase with new oil. Level should be at top of
indicator on dipstick.

7. Reinstall oil fi ll cap/dipstick and tighten securely.

8. Start engine; check for oil leaks. Stop engine; correct
leaks. Recheck oil level.

9. Dispose of used oil and fi lter in accordance with
local ordinances.

OIL COOLER (if equipped)

1. Clean fi ns with a brush or compressed air.

2. Remove screws securing oil cooler and tilt to clean
back side.

3. Reinstall oil cooler.

2924 690 34 Rev. D KohlerEngines.com

Lubrication System

OIL SENTRY

(if equipped)

™

This switch is designed to prevent engine from starting
in a low oil or no oil condition. Oil Sentry™ may not shut
down a running engine before damage occurs. In some
applications this switch may activate a warning signal.
Read your equipment manuals for more information.

Oil Sentry
On engines not equipped with Oil Sentry™ installation

pressure switch is installed in breather cover.

™

hole is sealed with a 1/8-27 N.P.T.F. pipe plug.

Installation

1. Apply pipe sealant with Tefl on® (Loctite® PST® 592™
Thread Sealant or equivalent) to threads of switch.

2. Install switch into tapped hole in breather cover.

3. Torque switch to 4.5 N·m (40 in. lb.).

Testing

Compressed air, a pressure regulator, pressure gauge,
and a continuity tester are required to test switch.

1. Connect continuity tester across blade terminal and
metal case of switch. With 0 psi pressure applied to
switch, tester should indicate continuity (switch
closed).

2. Gradually increase pressure to switch. As pressure
increases through range of 3-5 psi tester should
indicate a change to no continuity (switch open).
Switch should remain open as pressure is increased
to 90 psi maximum.

3. Gradually decrease pressure through range of 3-5
psi. Tester should indicate a change to continuity
(switch closed) down to 0 psi.

4. Replace switch if it does not operate as specifi ed.

30 24 690 34 Rev. DKohlerEngines.com

Electrical System

SPARK PLUGS

CAUTION

Electrical Shock can cause injury.
Do not touch wires while engine is running.

Spark Plug Component and Details

A

B

C

Inspection

Inspect each spark plug as it is removed from cylinder
head. Deposits on tip are an indication of general
condition of piston rings, valves, and carburetor.

Normal and fouled plugs are shown in following photos:

Normal

Plug taken from an engine operating under normal
conditions will have light tan or gray colored deposits. If
center electrode is not worn, plug can be set to proper
gap and reused.

Worn

D

A Wire Gauge B Spark Plug
C Ground Electrode D Gap

NOTE: Do not clean spark plug in a machine using

abrasive grit. Some grit could remain in spark
plug and enter engine causing extensive wear
and damage.

Engine misfi re or starting problems are often caused
by a spark plug that has improper gap or is in poor
condition.

Engine is equipped with following spark plugs:

Gap 0.76 mm (0.03 in.)
Thread Size 14 mm
Reach 19.1 mm (3/4 in.)
Hex Size 15.9 mm (5/8 in.)

Refer to Maintenance for Repairs/Service Parts.

Service

Clean out spark plug recess. Remove plug and replace.

1. Check gap using wire feeler gauge. Adjust gap to

0.76 mm (0.03 in.).

2. Install plug into cylinder head.

3. Torque plug to 27 N·m (20 ft. lb.).

On a worn plug, center electrode will be rounded and
gap will be greater than specifi ed gap. Replace a worn
spark plug immediately.

Wet Fouled

A wet plug is caused by excess fuel or oil in combustion
chamber. Excess fuel could be caused by a restricted air
cleaner, a carburetor problem, or operating engine with
too much choke. Oil in combustion chamber is usually
caused by a restricted air cleaner, a breather problem,
worn piston rings, or valve guides.

3124 690 34 Rev. D KohlerEngines.com

Electrical System

Carbon Fouled

Soft, sooty, black deposits indicate incomplete
combustion caused by a restricted air cleaner, over rich
carburetion, weak ignition, or poor compression.

Overheated

Chalky, white deposits indicate very high combustion
temperatures. This condition is usually accompanied
by excessive gap erosion. Lean carburetor settings,
an intake air leak, or incorrect spark timing are normal
causes for high combustion temperatures.

BATTERY

A 12-volt battery with 400 cold cranking amps (cca) is
generally recommended for starting in all conditions. A
smaller capacity battery is often suffi cient if an
application is started only in warmer temperatures. Refer
to following table for minimum capacities based on
anticipated ambient temperatures. Actual cold cranking
requirement depends on engine size, application, and
starting temperatures. Cranking requirements increase
as temperatures decrease and battery capacity shrinks.
Refer to equipment's operating instructions for specifi c
battery requirements.

Battery Size Recommendations

Temperature Battery Required

Above 32°F (0°C) 200 cca minimum

0°F to 32°F (-18°C to 0°C) 250 cca minimum

-5°F to 0°F (-21°C to -18°C) 300 cca minimum

-10°F (-23°C) or below 400 cca minimum

If battery charge is insuffi cient to turn over engine,
recharge battery.

ELECTRONIC IGNITION SYSTEMS
Ignition System Components

F

A

B

C

Kill Switch/

A

C Flywheel D Magnet

E Spark Plug F Ignition Modules

There are 2 different types of ignition systems used on
these engines. All systems use an ignition module which
energizes spark plug. Difference in systems is in way
ignition timing is triggered.

Both ignition systems are designed to be trouble free for
life of engine. Other than periodically checking/replacing
spark plugs, no maintenance or timing adjustments
are necessary or possible. Mechanical systems do
occasionally fail or break down. Refer to Troubleshooting
to determine root of a reported problem.

Reported ignition problems are most often due to poor
connections. Before beginning test procedure, check
all external wiring. Be certain all ignition-related wires
are connected, including spark plug leads. Be certain all
terminal connections fi t snugly. Make sure ignition switch
is in run position.

Off Position of

Key Switch

B Air Gap

D

E

Battery Maintenance

Regular maintenance is necessary to prolong battery
life.

Battery Test

To test battery, follow manufacturer's instructions.

32 24 690 34 Rev. DKohlerEngines.com

Wiring Diagram-15/20/25 Amp Regulated Battery Charging System

A

Electrical System

AB

C

AA

V

AC

B

D

Z

Y

F

E

F

G

I

W

A

H

AI

AJ

V

AM

AH

V

AL

T

U

X

AF

AE

AK

R

AD

AG

AO

AN

W

AH

R

V

R

S

Q

T

R

O

P

N

M

B

J

K

L

3324 690 34 Rev. D KohlerEngines.com

Electrical System

Ignition Systems

These systems use a capacitive discharge (CD) coil. With CDI fi xed timing, ignition timing and spark remains constant
regardless of engine speed. Timing of spark is controlled by location of fl ywheel magnet group as referenced to
engine TDC. MDI adjustable timing uses a digital microprocessor which is located in ignition modules. Ignition timing
varies depending upon engine speed with this system.

A typical ignition system consists of:

● 1 magnet assembly which is permanently affi xed to fl ywheel.

● 2 electronic capacitive-discharge ignition modules which mount on engine crankcase.

● 1 kill switch (or key switch) which grounds modules to stop engine.

● 2 spark plugs.

A Spark Plug(s) B Oil Pressure Switch C Oil Sentry™ (Green) D White Kill

E

Flywheel Stator

Assembly

F Ignition Module G

I Rectifi er-Regulator J Oil Sentry™ Kill (Green) K Violet B+ L

M Starter Solenoid Tang N Starter Solenoid Stud O Fuse P Blue

Alternate Ignition Kill

Q

(–)

R White S Accessory Terminal (+) T Yellow

U Ignition Kill V Red W Carburetor X Carburetor Solenoid

Non-Smart Spark

Ignition

™

Rectifi er-Regulator

H

Connector

Solenoid Shift Starter

Assembly

Y Black (Ground) Z Intake Manifold Screw AA Black AB

Oil Sentry™ Panel

Light/Remote Light

AC Oil Sentry™ Light AD Connector AE Magneto AF Key Switch

AG Accessory AH Battery AI Starter AJ Ground
AK Key Switch Ground AL Rectifi er AM Blue/Red AN Battery Positive
AO Battery Negative

Electronic Ignition Systems Tests

NOTE: Ignition tester must be used to test ignition on these engines. Use of any other tester can result in inaccurate

fi ndings. Battery on unit must be fully charged and properly connected before performing tests (a battery that
is hooked up or charged backward will crank engine but it won’t have spark). Be certain drive is in neutral and
all external loads are disconnected.

Test Ignition Systems

NOTE: If engine starts or runs during testing, you may need to ground kill lead to shut it down. Because you have

interrupted kill circuit, it may not stop using switch.

Isolate and verify trouble is within engine.

1. Locate connectors where wiring harnesses from engine and equipment are joined. Separate connectors and
remove white kill lead from engine connector. Rejoin connectors and position or insulate kill lead terminal so it
cannot touch ground. Try to start engine to verify whether reported problem is still present.

Condition Possible Cause Conclusion

Problem goes away. Electrical System Check key switch, wires, connections,

safety interlocks, etc.

Problem persists. Ignition or Electrical System Leave kill lead isolated until all testing

is completed.
Identify white kill lead of engine

wiring harness connector. Establish
a connection to a known good
ground location. Engine should kill
completely. If not or only one cylinder
is affected, check ignition modules
and white kill lead connection for
affected module.

34 24 690 34 Rev. DKohlerEngines.com

Electrical System

Test for Spark

NOTE: If 2 testers are available, testing can be performed simultaneously for both cylinders. However, if only 1 tester

is available, 2 individual tests must be performed. Side not being tested must have spark plug lead connected
or grounded. Do not crank engine or perform tests with 1 spark plug lead disconnected and not grounded, or
permanent system damage may occur.

1. With engine stopped, disconnect 1 spark plug lead. Connect spark plug lead to post terminal of spark tester and

attach tester clip to a good engine ground.

2. Crank engine over, establishing a minimum of 550-600 RPM, and observe tester(s) for spark.

3. Repeat spark test on opposite cylinder if cylinders are being tested individually.

Condition Possible Cause Conclusion

Both cylinders have good spark but
engine runs poorly or existing plug
condition is questionable.

1 cylinder has good spark and other
cylinder has no or intermittent spark.

Spark on both cylinders but power is
suspect.

Check Ignition Modules and Connections

1. Remove blower housing from engine. Inspect kill wire for any damage, cuts, or shorts to engine or ignition module

body. Check that connections are oriented properly on terminals of modules.

2. On MDI adjustable timing engines, ensure that both modules are correctly installed with fl at side of module out/

towards you.

Spark Plug(s) Install new spark plug(s) and retest

engine performance.

Ignition Test ignition modules and

connections.

Sheared Flywheel Key Check for broken key.

Condition Possible Cause Conclusion

All checks are OK but module has no
spark or fails to advance.

BATTERY CHARGING SYSTEM

NOTE: Observe following guidelines to avoid damage to electrical system and components:

● Make sure battery polarity is correct. A negative (–) ground system is used.

● Disconnect rectifi er-regulator plug and/or wiring harness plug before doing any electric welding on equipment

powered by engine. Disconnect all other electrical accessories in common ground with engine.

● Prevent stator (AC) leads from touching or shorting while engine is running. This could damage stator.

Most engines are equipped with a 15 or 20 amp regulated charging system. Some have a 25 amp regulated charging
system.

15/20/25 Amp Regulated Charging System

Stator

Stator is mounted on crankcase behind fl ywheel. Follow procedures in Disassembly and Reassembly if stator
replacement is necessary.

Rectifi er-Regulator

NOTE: When installing rectifi er-regulator, take note of terminal markings and install plug(s) accordingly.
NOTE: Disconnect all electrical connections attached to rectifi er-regulator. Testing may be performed with rectifi er-

regulator mounted or loose. Repeat applicable test procedure 2 or 3 times to determine condition of part.

Rectifi er-regulator is mounted on blower housing. To replace it, disconnect plug(s), remove two mounting screws, and
ground wire or metal grounding strap.

Testing of rectifi er-regulator may be performed as follows, using appropriate Rectifi er-Regulator Tester.
To test 15 amp rectifi er-regulators:

1. Connect tester ground lead (with spring clamp) to body of rectifi er-regulator being tested.

2. Connect tester red lead to B+ terminal of rectifi er-regulator and 2 black tester leads to 2 AC terminals.

3. Plug tester into proper AC outlet/power for tester being used. Turn on power switch. POWER light should be

illuminated and 1 of 4 status lights may be on as well. This does not represent condition of part.

4. Press TEST button until a click is heard and then release. Momentarily 1 of 4 status lights will illuminate, indicating

condition of part.

Ignition Module Replace affected module.

3524 690 34 Rev. D KohlerEngines.com

Electrical System

To test 20/25 amp rectifi er-regulators:

1. 20 amp: Connect single lead adapter in between B+ (center) terminal of rectifi er-regulator being tested and
squared single end of tandem adapter lead.

25 amp: Connect squared single end of tandem lead adapter to B+ (center/red) lead of rectifi er-regulator being

tested.

2. Connect tester ground lead (with spring clamp) to body of rectifi er-regulator.

3. Connect red lead and 1 of black leads to pair of terminals on open end of tandem adapter lead (connections are
not location specifi c).

4. Connect remaining black lead from tester to 1 of outer AC terminals on rectifi er-regulator.

5. Plug tester into proper AC outlet/power for tester being used. Turn on power switch. POWER light should be
illuminated and 1 of 4 status lights may be on as well. This does not represent condition of part.

6. Press TEST button until a click is heard and then release. Momentarily 1 of 4 status lights will illuminate indicating
partial condition of part.

Condition Conclusion

4 amp 15 Amp 20 amp 25 amp

OK (green) or HIGH light comes on
and stays steady.

NOTE: A fl ashing LOW light can

also occur as a result of an
inadequate ground lead
connection. Make certain
connection location is clean
and clamp is secure.

Other lights come on.

Part is good and may be used. Disconnect tester black lead attached

to 1 AC terminal and reconnect it to
other AC terminal. Repeat test. If OK
(green) light comes on again, part is
good and may be used.

Rectifi er-regulator is faulty and should not be used.

36 24 690 34 Rev. DKohlerEngines.com

Electrical System

15/20/25 Amp Battery Charging Systems

NOTE: Always zero ohmmeter on each scale before testing to ensure accurate readings. Voltage tests should be

made with engine running at 3600 RPM with no load. Battery must be good and fully charged.

When problems occur in keeping battery charged or battery charges at high rate, charging system or battery might be
causing problems.

To test charging system for no charge to battery:

1. Insert an ammeter in B+ lead from rectifi er-regulator.

With engine running at 3600 RPM and B+ (at
terminal on rectifi er-regulator) to ground using a DC
voltmeter.

If voltage is 13.8 volts or more, place a minimum

load of 5 amps (turn on lights if 60 watts or more, or
place a 2.5 ohm, 100 watt resistor across battery
terminals) on battery to reduce voltage. Observe
ammeter.

Condition Conclusion

Charge rate increases
when load is applied.

Charge rate does not
increase when load is
applied.

2. Remove connector from rectifi er-regulator. With

engine running at 3600 RPM, measure AC voltage
across stator leads using an AC voltmeter.

Condition Conclusion

Voltage is 28 volts or
more.

Voltage is less than 28
volts.

Charging system is OK
and battery was fully
charged.

Test stator and rectifi er-
regulator (steps 2 and 3).

Stator is OK. Rectifi er-
regulator is faulty; replace.

Stator is faulty; replace.
Test stator further using an
ohmmeter (steps 3 and 4).

To test charging system for battery continuously charging
at high rate:

1. With engine running at 3600 RPM, measure voltage
from B+ lead to ground using a DC voltmeter.

Condition Conclusion

Voltage is 14.7 volts or
less.

Voltage is more than 14.7
volts.

Charging system is OK.
Battery is unable to hold
charge; service or replace.

Faulty rectifi er-regulator;
replace.

3. With engine stopped, measure resistance across
stator leads using an ohmmeter.

Condition Conclusion

Resistance is 0.1/0.2
ohms.

Resistance is 0 ohms. Stator is shorted; replace.
Resistance is infi nity

ohms.

4. With engine stopped, measure resistance from each
stator lead to ground using an ohmmeter.

Condition Conclusion

Resistance is infi nity ohms
(no continuity).

Resistance (or continuity)
measured.

Stator is OK.

Stator is open; replace.

Stator is OK (not shorted
to ground).

Stator leads are shorted to
ground; replace.

3724 690 34 Rev. D KohlerEngines.com

Starter System

NOTE: Do not crank engine continuously for more than 10 seconds. Allow a 60 second cool down period between

starting attempts. Failure to follow these guidelines can burn out starter motor.

NOTE: If engine develops suffi cient speed to disengage starter but does not keep running (a false start), engine

rotation must be allowed to come to a complete stop before attempting to restart engine. If starter is engaged
while fl ywheel is rotating, starter pinion and fl ywheel ring gear may clash and damage starter.

NOTE: If starter does not crank engine, shut off starter immediately. Do not make further attempts to start engine until

condition is corrected.

NOTE: Do not drop starter or strike starter frame. Doing so can damage starter.
Engines in this series use solenoid shift starters.

Troubleshooting-Starting Diffi culties

Condition Possible Cause Conclusion

Starter does not energize. Battery Check specifi c gravity of battery. If low, recharge or replace

battery as necessary.

Wiring Clean corroded connections and tighten loose connections.

Replace wires in poor condition and with frayed or broken
insulation.

Starter energizes but turns
slowly.

Starter Switch

or Solenoid

Battery Check specifi c gravity of battery. If low, recharge or replace

Brushes Check for excessively dirty or worn brushes and commutator.

Transmission

or

Engine

By-pass switch or solenoid with a jumper wire. If starter cranks
normally, replace faulty components. Remove and perform
individual solenoid test procedure.

battery as necessary.

Clean using a coarse cloth (not emery cloth).
Replace brushes if excessively or unevenly worn.

Make sure clutch or transmission is disengaged or placed
in neutral. This is especially important on equipment with
hydrostatic drive. Transmission must be exactly in neutral to
prevent resistance which could keep engine from starting.

Check for seized engine components such as bearings,
connecting rod, and piston.

38

KohlerEngines.com

24 690 34 Rev. D

Starter System

SOLENOID SHIFT ELECTRIC STARTERS
Solenoid Shift Starter Components

H

G

F

E

D

C

P

B

A

Q

R

S

T

Starter Disassembly

NOTE: Do not reuse old retainer.

I

J

K

L

M

N

O

NOTE: Do not soak armature or use solvent when

cleaning. Wipe clean using a soft cloth, or use
compressed air.

1. Remove hex nut and disconnect positive (+) brush
lead/bracket from solenoid terminal.

2. Remove head screws securing solenoid to starter.

3. If solenoid was mounted with Phillips head screws,
separate solenoid and plunger spring from drive end
cap. If solenoid was mounted with external Torx
head screws, plunger is part of solenoid, unhook
plunger pin from drive lever. Remove gasket from
recess in housing.

4. Remove thru (larger) bolts.

5. Remove commutator end plate assembly, containing
brush holder, brushes, springs, and locking caps.
Remove thrust washer from inside commutator end.

6. Remove frame from armature and drive end cap.

7. Remove drive lever pivot bushing and backing plate
from end cap.

8. Take out drive lever and pull armature out of drive
end cap.

9. Remove thrust washer from armature shaft.

10. Push stop collar down to expose retaining ring.

11. Remove retainer from armature shaft. Save stop
collar.

12. Remove drive pinion assembly from armature.

13. Clean parts as required.

U

A Tube B Washer
C Armature D Drive
E Stop F Retaining Ring

G Collar H Drive End Cap

I Screw J Plunger
K Spring L Lever
M Plate N Plug
O Solenoid P Frame and Field
Q Brush Holder R Nut

Commutator End

S

U Bolt

When power is applied to starter electric solenoid moves
drive pinion out onto drive shaft and into mesh with
fl ywheel ring gear. When pinion reaches end of drive
shaft it rotates fl ywheel and cranks engine.

When engine starts and start switch is released, starter
solenoid is deactivated, drive lever moves back, and
drive pinion moves out of mesh with ring gear into
retracted position.

24 690 34 Rev. D

Plate

T

Screw

KohlerEngines.com 39

Inspection

Check drive pinion and inspect following areas:

● Pinion teeth for abnormal wear or damage.

● Surface between pinion and clutch mechanism for

nicks or irregularities which could cause seal damage.

● Check drive clutch by holding clutch housing and
rotating pinion. Pinion should rotate in only 1 direction.

Brushes and Springs
Detail

A

A Wear Limit Length

Inspect both springs and brushes for wear, fatigue, or
damage. Measure length of each brush. Minimum length
for each brush is 7.6 mm (0.300 in.). Replace brushes if
they are worn, undersize, or condition is questionable.

Starter System

Armature
Components and Details

A

B

A Commutator O.D. B Mica Insulation

C

E

D

C Insulation Check D Armature Coil
E Continuity Check

1. Clean and inspect commutator (outer surface). Mica
insulation must be lower than commutator bars
(undercut) to ensure proper operation of
commutator.

2. Use an ohmmeter set to Rx1 scale. Touch probes
between 2 different segments of commutator, and
check for continuity. Test all segments. Continuity
must exist between all or armature is bad.

3. Check for continuity between armature coil
segments and commutator segments. There should
be no continuity. If continuity exists between any 2
armature is bad.

4. Check armature windings/insulation for shorting.

Shift Fork

Check that shift fork is complete, and pivot and contact
areas are not excessively worn, cracked, or broken.

Brush Replacement

4 brushes and springs are serviced as a set. Use a new
Kohler brush and spring kit if replacement is necessary.

1. Perform steps 1-5 in Starter Disassembly.

2. Remove screws securing brush holder assembly to
end cap (plate). Note orientation for reassembly
later. Discard old brush holder assembly.

3. Clean component parts as required.

4. New brushes and springs come preassembled in a
brush holder with a protective sleeve that will also
serve as an installation tool.

5. Perform Steps 10-13 in Starter Reassembly
sequence. Installation must be done after armature,
drive lever, and frame are installed, if starter has
been disassembled.

Starter Reassembly

NOTE: Always use a new retainer. Do not reuse old

retainers that have been removed.

NOTE: Correctly installed, center pivot section of drive

lever will be fl ush or below machined surface of
housing.

1. Apply drive lubricant to armature shaft splines. Install
drive pinion onto armature shaft.

2. Install and assemble stop collar/retainer assembly.

a. Install stop collar down onto armature shaft with

counter bore (recess) up.

b. Install a new retainer in larger (rear) groove of

armature shaft. Squeeze with a pliers to
compress it in groove.

c. Slide stop collar up and lock it into place, so

recess surrounds retainer in groove. If necessary,
rotate pinion outward on armature splines against
retainer to help seat collar around retainer.

3. Install offset thrust (stop) washer so smaller offset of
washer faces retainer/collar.

4. Apply a small amount of oil to bearing in drive end
cap, and install armature with drive pinion.

5. Lubricate fork end and center pivot of drive lever
with drive lubricant. Position fork end into space
between captured washer and rear of pinion.

6. Slide armature into drive end cap and at same time
seat drive lever into housing.

7. Install backup washer, followed by rubber grommet,
into matching recess of drive end cap. Molded
recesses in grommet should be out, matching and
aligned with those in end cap.

8. Install frame, with small notch forward, onto
armature and drive end cap. Align notch with
corresponding section in rubber grommet. Install
drain tube in rear cutout, if it was removed
previously.

9. Install fl at thrust washer onto commutator end of
armature shaft.

10. Starter reassembly when replacing brushes/brush
holder assembly:

a. Hold starter assembly vertically on end housing,

and carefully position assembled brush holder
assembly, with supplied protective tube, against
end of commutator/armature. Mounting screw
holes in metal clips must be up/out. Slide brush
holder assembly down into place around
commutator, and install positive (+) brush lead
grommet in cutout of frame. Protective tube may
be saved and used for future servicing.

Starter reassembly when not replacing brushes/

brush holder assembly:

a. Carefully unhook retaining caps from brush

assemblies. Do not lose springs.

40

KohlerEngines.com

24 690 34 Rev. D

Starter System

b. Position brushes back in their slots so they are fl ush with I.D. of brush holder assembly. Insert brush

installation tool (with extension), or use tube described above from a prior brush installation, through brush

holder assembly, so holes in metal mounting clips are up/out.
c. Install brush springs and snap on retainer caps.
d. Hold starter assembly vertically on end housing, and carefully place tool (with extension) and assembled

original brush holder assembly onto end of armature shaft. Slide brush holder assembly down into place

around commutator, install positive (+) brush lead grommet in cutout of frame.

11. Install end cap onto armature and frame, aligning thin raised rib in end cap with corresponding slot in grommet of

positive (+) brush lead.

12. Install thru bolts and brush holder mounting screws. Torque bolts to 5.6-9.0 N·m (49-79 in. lb.) and brush holder

mounting screws to 2.5-3.3 N·m (22-29 in. lb.).

13. Hook plunger behind upper end of drive lever and install spring into solenoid. Insert mounting screws through

holes in drive end cap. Use these to hold solenoid gasket in position, then mount solenoid. Torque screws to

4.0-6.0 N·m (35-53 in. lb.).

14. Connect positive (+) brush lead/bracket to solenoid and secure with nut. Torque nut to 8-11 N·m (71-97 in. lb.). Do

not overtighten.

Solenoid Tests

NOTE: DO NOT leave 12 volt test leads connected to solenoid for any time over what is necessary for performing

each of individual tests. Internal damage to solenoid may occur.

Disconnect all leads from solenoid including positive brush lead attached to lower stud terminal. Remove mounting
hardware and separate solenoid from starter for testing.

To test solenoid pull-in coil/plunger:
Actuation

1. Use a 12 volt power supply and 2 test leads.

2. Connect 1 lead to fl at spade S/start terminal on solenoid. Momentarily connect other lead to lower large post

terminal.
When connection is made solenoid should energize (audible click) and plunger retract. Repeat test several times.
Continuity

1. Use an ohmmeter set to audible or Rx2K scale, and connect 2 ohmmeter leads to 2 large post terminals.

2. Perform solenoid pull-in coil/plunger actuation test and check for continuity. Ohmmeter should indicate continuity.

Repeat test several times.
To test solenoid hold-in coil:
Function

1. Connect a 12 volt test lead to fl at spade S/start terminal on solenoid and other lead to body or mounting surface

of solenoid.

2. Manually push plunger IN and check if coil holds plunger retracted. Do not allow test leads to remain connected to

solenoid for a prolonged period of time.
Continuity

1. Use an ohmmeter set to audible or Rx2K scale, and connect 2 ohmmeter leads to 2 large post terminals.

2. Perform preceding solenoid hold-in coil function test and check for continuity. Meter should indicate continuity.

Repeat test several times.

Condition Conclusion

Solenoid fails to activate. Replace solenoid.
No continuity is indicated.
Plunger fails to stay retracted.

24 690 34 Rev. D

KohlerEngines.com 41

Disassembly/Inspection and Service

WARNING

Accidental Starts can cause severe injury or
death.

Disconnect and ground spark plug lead(s)
before servicing.

External Engine Components

E

D

C

A

F

I

J

K

Before working on engine or equipment, disable engine as
follows: 1) Disconnect spark plug lead(s). 2) Disconnect
negative (–) battery cable from battery.

X

G

H

L

V

M

B

K

W

R

F

Q

S

T

P

O

N

A Intake Manifold B

E Air Cleaner Gasket F Outer Baffl e G Breather Tube H Oil Sentry

Intake Manifold

Gasket

C Carburetor Gasket D Carburetor

™

I Breather Cover J Breather Gasket K Inner Baffl e L Breather Reed

U

42

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

M Filter N Electric Starter O Lifting Bracket P Fixed Guard

Q Blower Housing R Wire Clip S Oil Filter T Nipple

U Oil Cooler V

Valve Cover Fuel

Pump

W Pulse Fuel Pump X Air Cleaner

Clean all parts thoroughly as engine is disassembled.
Only clean parts can be accurately inspected
and gauged for wear or damage. There are many
commercially available cleaners that will quickly remove
grease, oil, and grime from engine parts. When such a
cleaner is used, follow manufacturer’s instructions and
safety precautions carefully.

Make sure all traces of cleaner are removed before
engine is reassembled and placed into operation. Even
small amounts of these cleaners can quickly break down
lubricating properties of engine oil.

Disconnect Spark Plug Leads

NOTE: Pull on boot only, to prevent damage to spark

plug lead.

1. Disconnect leads from spark plugs.

2. Shut off fuel supply.

Drain Oil from Crankcase and Remove Oil Filter

1. Remove oil fi ll cap, dipstick, and 1 oil drain plug.

2. Allow ample time for oil to drain from crankcase and

oil fi lter.

3. Remove and discard oil fi lter.

4. An oil cooler is standard equipment on some models

and an option on others.

Remove Muffl er

Remove exhaust system and attaching hardware from
engine. On engines equipped with a port liner, remove it
now.

Remove Air Cleaner Assembly

1. Disconnect breather hose from fi tting in adapter or

elbow.

2. Remove nuts securing adapter or elbow.

3. Remove screws securing main support bracket for

air cleaner to valve covers. Remove mounting
screws into top of intake manifold. Unhook choke
return spring if equipped. Do not lose any hardware.

4. Remove air cleaner as an assembly from engine.

Remove Fuel Pump

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings,
away from sparks or fl ames. Spilled fuel could ignite
if it comes in contact with hot parts or sparks from
ignition. Never use gasoline as a cleaning agent.

Pulse Style Pumps

1. Disconnect fuel lines at carburetor and at in-line fuel
fi lter.

2. Disconnect pulse (vacuum) line from crankcase.

3. Remove screws securing fuel pump to blower
housing.

4. Note or mark orientation of fuel pump, then remove
fuel pump with lines attached.

Mechanical Fuel Pump

A mechanical style fuel pump is part of valve cover
assembly.

1. Disconnect fuel lines at pump outlet and at in-line
fuel fi lter.

2. Fuel pump will be removed with valve cover. Refer to
valve cover removal procedure.

Remove Control Panel (if equipped)

1. Disconnect Oil Sentry™ indicator light wires.

2. Disconnect choke control cable from control bracket.

3. Disconnect throttle control cable or shaft.

4. Remove panel from blower housing.

24 690 34 Rev. D KohlerEngines.com

43

Disassembly/Inspection and Service

Remove Throttle and Choke Controls

Control Bracket Components

B

A

G

C

F

E

D

A Choke Linkage B Control Bracket

C Governor Spring D Governor Lever

E Nut F Throttle Linkage

G

1. Remove screws securing control bracket and rear air

2. Mark spring hole locations and disconnect spring

3. Remove choke linkage from choke actuator lever

Remove External Governor Controls

Loosen nut and remove governor lever from cross shaft.
Leave lever attached to throttle linkage and lay assembly
on top of crankcase.

Remove Carburetor

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings,
away from sparks or fl ames. Spilled fuel could ignite
if it comes in contact with hot parts or sparks from
ignition. Never use gasoline as a cleaning agent.

1. Disconnect fuel shut-off solenoid lead and ground

Governed Idle

Spring

cleaner bracket (some models) to cylinder heads.

from governor lever.

and carburetor.

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

lead, if equipped.

2. If required use nuts locked together and remove
carburetor mounting studs on starter side of intake
manifold and one stud on oil fi lter side.

Pivot carburetor to clear breather cover fi tting and

pressure switch (if equipped). Remove carburetor,
throttle linkage, choke linkage, and governor lever as
an assembly.

3. Remove carburetor, throttle linkage and governor
lever as an assembly.

4. Remove carburetor gasket.

5. If necessary, carburetor, throttle linkage and
governor lever can be separated. Reattach bushings
to linkage following separation to avoid losing them.

Remove Oil Sentry™ (if equipped)

1. Disconnect lead from Oil Sentry™ switch.

2. Remove Oil Sentry™ switch from breather cover.

Remove Electric Starter Motor

1. Disconnect leads from starter.

2. Remove screws and starter assembly.

Remove Outer Baffl es and Blower Housing

1. Disconnect plug from rectifi er-regulator on blower
housing.

2. Use tip of dipstick or a similar small fl at tool to bend
locking tang, then remove B+ (center lead) from
terminal plug as shown. This will allow blower
housing to be removed without disturbing wiring
harness.

3. Rectifi er-regulator does not have to be detached
from blower housing.

4. Remove screws securing outer baffl es. Note location
of any lifting strap and position of two short screws
(one each side on bottom) for reassembly.

5. Remove outer baffl es on both sides.

6. Remove debris screen before removing blower
housing.

7. Remove lower blower housing screw and washer
securing rectifi er-regulator ground lead or grounding
strap.

8. Remove remaining screws and detach blower
housing.

9. Disconnect plug from key switch in blower housing if
engine is equipped.

Remove Inner Baffl es and Breather Cover

Inner (valley) baffl es are attached at one corner using
same fasteners as breather cover.

1. Remove screws securing inner baffl es.

2. Remove both inner baffl es.

3. Remove two remaining screws holding breather
cover to crankcase.

4. Remove breather cover and gasket.

5. Remove breather fi lter from chamber.

6. Remove screw, breather reed retainer and breather
reed.

44

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

Remove Intake Manifold

1. Remove screws securing intake manifold to cylinder
heads. Note which screws hold wiring clamps.

2. Remove intake manifold and intake manifold
gaskets.

3. Leave wiring harness attached to manifold.

Cylinder Head Components

B

Remove Valve Covers

1. Remove screws securing each valve cover. Note
position of any attached brackets or lifting straps.

2. Remove valve covers, O-rings, and any brackets or
lifting straps. Note which side of engine has oil fi ll
and or fuel pump valve cover.

K

G

J

I

H

F

E

N

M

L

P

O

D

A

A Valve B Stud C Gasket D Spark Plug

E Cap F Valve Stem Seal G Hydraulic Lifter H Retainer

I Valve Spring J Valve Spring Retainer K Push Rod L Valve Keeper

M Rocker Arm N Rocker Arm Pivot O Valve Cover O-ring P Valve Cover

Remove Spark Plugs

Remove spark plug from each cylinder head.

Remove Cylinder Heads and Hydraulic Lifters

NOTE: Cylinder heads are retained using either screws

or nuts and washers on studs. Do not
interchange or mix components, as cylinder
heads may have different machining, unique to
each fastening method.

NOTE: Exhaust lifters are located on output shaft side

of engine while intake lifters are located on fan
side of engine. Cylinder head number is
embossed on outside of each cylinder head.

1. Remove screws or nuts and washers securing each
cylinder head. Unless screws are damaged or
questionable, they can be reused. Discard nuts and
washers once removed; do not reuse. Studs (if
present) should only be removed if damaged or if
cylinder reconditioning is necessary. Once removed,
they must be replaced.

C

2. Mark position of push rods as either intake or
exhaust and cylinder 1 or 2. Push rods should
always be reinstalled in same positions.

3. Carefully remove push rods, cylinder heads and
head gaskets.

4. Remove lifters from lifter bores. Use a Hydraulic
Lifter Tool. Do not use a magnet to remove lifters.
Mark lifters by location, as either intake or exhaust
and cylinder 1 or 2. Hydraulic lifters should always
be reinstalled in same position.

24 690 34 Rev. D KohlerEngines.com

45

Disassembly/Inspection and Service

Disassemble Cylinder Heads

NOTE: These engines use valve stem seals on intake

valves. Use a new seal whenever valve is
removed or if seal is deteriorated in any way.
Never reuse an old seal.

1. Remove screws, rocker arm pivots and rocker arms
from cylinder head.

2. Compress valve springs using a valve spring
compressor.

Inspection and Service
Valve Details

EXHAUST VALVE INTAKE VALVE

E

F

C

G

D

3. Once valve spring is compressed, remove following
items.

● Valve spring keepers.

● Valve spring retainers.

● Valve springs.

● Valve spring caps.

● Intake and exhaust valves (mark position).

● Valve stem seals (intake valve only).

4. Repeat above procedure for other cylinder head. Do
not interchange parts from one cylinder head to
other.

B

EXHAUST
INSERT

A

F

E

G

H

D

INTAKE
INSERT

B

A

H

Dimension Intake Exhaust

A Seat Angle 89° 89°
B Insert O.D. 36.987/37.013 mm (1.4562/1.4572 in.) 32.987/33.013 mm (1.2987/1.2997 in.)
C Guide Depth 4 mm (0.1575 in.) 6.5 mm (0.2559 in.)
D Guide I.D. 7.038/7.058 mm (0.2771/0.2779 in.) 7.038/7.058 mm (0.2771/0.2779 in.)
E Valve Head Diameter 33.37/33.63 mm (1.3138/1.3240 in.) 29.37/29.63 mm (1.1563/1.1665 in.)

F Valve Face Angle 45° 45°
G Valve Margin (Min.) 1.5 mm (0.0591 in.) 1.5 mm (0.0591 in.)
H Valve Stem Diameter 6.982/7.000 mm (0.2749/0.2756 in.) 6.970/6.988 mm (0.2744/0.2751 in.)

46

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

After cleaning, check fl atness of cylinder head and
corresponding top surface of crankcase, using a surface
plate or piece of glass and feeler gauge. Maximum
allowable out of fl atness is:

0.076 mm (0.003 in.) for 80 mm bores;

0.1 mm (0.003 in.) for 83 mm bore.
Carefully inspect valve mechanism parts. Inspect valve

springs and related hardware for excessive wear or
distortion. Check valves and valve seat area or inserts
for evidence of deep pitting, cracks, or distortion. Check
clearance of valve stems in guides.

Hard starting or loss of power accompanied by high
fuel consumption may be symptoms of faulty valves.
Although these symptoms could also be attributed to
worn rings, remove and check valves fi rst. After removal,
clean valve heads, faces, and stems with a power wire
brush.

Then, carefully inspect each valve for defects such as a
warped head, excessive corrosion, or a worn stem end.
Replace valves found to be in bad condition.

Valve Guides

If a valve guide is worn beyond specifi cations, it will not
guide valve in a straight line. This may result in burnt
valve faces or seats, loss of compression, and excessive
oil consumption.

To check valve guide-to-valve stem clearance,
thoroughly clean valve guide and, using a split-ball
gauge, measure inside diameter of guide. Then, using
an outside micrometer, measure diameter of valve stem
at several points on stem where it moves in valve guide.
Use largest stem diameter to calculate clearance by
subtracting stem diameter from guide diameter. If intake
clearance exceeds 0.038/0.076 mm (0.0015/0.0030
in.) or exhaust clearance exceeds 0.050/0.088 mm
(0.0020/0.0035 in.), determine whether valve stem or
guide is responsible for excessive clearance.

Maximum (I.D.) wear on intake valve guide is 7.134 mm
(0.2809 in.) while 7.159 mm (0.2819 in.) is maximum
allowed on exhaust guide. Guides are not removable but
can be reamed 0.25 mm (0.010 in.) oversize. Valves with

0.25 mm oversize stems must then be used.
If guides are within limits but valve stems are worn

beyond limits, install new valves.

Valve Seat Inserts

Hardened steel alloy intake and exhaust valve seat
inserts are press fi tted into cylinder head. Inserts are
not replaceable but can be reconditioned if not too badly
pitted or distorted. If cracked or badly warped, cylinder
head should be replaced.

Recondition valve seat inserts following instructions
provided with valve seat cutter being used. Final cut
should be made with an 89° cutter as specifi ed for
valve seat angle. Cutting proper 45° valve face angle
as specifi ed, and proper valve seat angle (44.5°, half of
full 89° angle), will achieve desired 0.5° (1.0° full cut)
interference angle where maximum pressure occurs on
outside diameters of valve face and seat.

Lapping Valves

NOTE: Exhaust valves that are black in color cannot be

ground and do not require lapping.

Reground or new valves must be lapped in, to provide
proper fi t. Use a hand valve grinder with a suction cup
for fi nal lapping. Lightly coat valve face with a fi ne grade
of grinding compound, then rotate valve on its seat with
grinder. Continue grinding until a smooth surface is
obtained on seat and on valve face. Thoroughly clean
cylinder head in soap and hot water to remove all traces
of grinding compound. After drying cylinder head, apply
a light coating of SAE 10 oil to prevent rusting.

Intake Valve Stem Seal

These engines use valve stem seals on intake valves.
Always use a new seal when valves are removed
from cylinder head. Seals should also be replaced if
deteriorated or damaged in any way. Never reuse an old
seal.

Hydraulic Lifters Inspection

Check base surface of hydraulic lifters for wear or
damage. If lifters need to be replaced, apply a liberal
coating of Kohler lubricant to base of each new lifter
before it is installed.

Bleeding Lifters

To prevent a possible bent push rod or broken rocker
arm, it is important to bleed any excess oil out of lifters
before they are installed.

1. Cut a 50-75 mm (2-3 in.) piece from end of an old
push rod and chuck it in a drill press.

2. Lay a rag or shop towel on table of drill press and
place lifter, open end up, on towel.

3. Lower chucked push rod until it contacts plunger in
lifter. Slowly pump plunger 2 or 3 times to force oil
out of feed hole in side of lifter.

24 690 34 Rev. D KohlerEngines.com

47

Disassembly/Inspection and Service

Flywheel/Ignition Components

J

I

G

E

A Debris Screen B Fan C Flywheel Screw D Washer

E Flywheel F Magnet G Stator H Ignition Module

I Backing Plate J Woodruff Key K Spring Washer L Spacer

M Ring Support N Metal Debris Screen O Washer P

Remove Ignition Modules

1. Disconnect lead from each ignition module.

2. Rotate fl ywheel so magnet is away from modules.

3. Remove mounting screws and ignition modules.
Note position of ignition modules.

Remove Debris Screen and Fan

1. Remove socket head cap screws securing metal
debris screen and remove screen.

2. Remove spacers, paying attention to curvature of
spring washers between spacers and fan.

3. If there is a plastic debris screen attached to fan,
remove screws securing screen. Removing screen
will expose screws fastening fan to fl ywheel.

4. Remove screws and fan.

Remove Flywheel

NOTE: Always use a fl ywheel strap wrench or holding

tool to hold fl ywheel when loosening or
tightening fl ywheel screw. Do not use any type
of bar or wedge to hold fl ywheel. Use of such
tools could cause fl ywheel to become cracked or
damaged.

NOTE: Always use a fl ywheel puller to remove fl ywheel

from crankshaft. Do not strike crankshaft or
fl ywheel, as these parts could become cracked
or damaged. Striking puller or crankshaft can
cause crank gear to move, affecting crankshaft
end play.

1. Use a fl ywheel strap wrench or holding tool (see
Tools and Aids) to hold fl ywheel and loosen screw
securing fl ywheel to crankshaft.

2. Remove screw and washer.

3. Use a puller to remove fl ywheel from crankshaft.

4. Remove woodruff key from crankshaft.

Inspection

Inspect fl ywheel for cracks and fl ywheel keyway for
damage. Replace fl ywheel if it is cracked. Replace
fl ywheel, crankshaft, and key if fl ywheel key is sheared
or keyway is damaged.

Inspect ring gear for cracks or damage. Kohler does not
provide ring gear as a serviceable part. Replace fl ywheel
if ring gear is damaged.

Remove Stator and Backing Plates

1. Remove screws securing backing plates and stator
wire bracket (if equipped). Remove backing plates
and stator wire bracket.

2. Remove screws and stator.

P

K

L

H

M

D

C

B

F

Metal Debris Screen

Assembly

O

N

A

48

KohlerEngines.com 24 690 34 Rev. D

Crankcase Components

R

Disassembly/Inspection and Service

V

K

T

U

A

Q

A Oil Seal B Closure Plate (Style A) C

E

M Piston N Connecting Rod O

Q Crankcase R Governor Cross Shaft S Closure Plate (Style B) T

U Ball (Style B) V Spring (Style B) W

Y

Oil Pick-Up Tube

(Style A)

I Camshaft J Piston Pin K Piston Ring Set L Piston Pin Retainer

Oil Pick-Up Tube

(Style B)

N

O

P

Oil Pump Assembly

F

M

(Style A)

J

X

W

L

H

I

G

F

E

Gerotor Gears

(Style A)

G Governor Gear Shaft H Governor Gear

Connecting Rod End

Cap

Oil Pump Cover O-ring

(Style B)

Y

S

D

C

B

D Dipstick Tube

P Crankshaft

Outer Gerotor Gear

(Style B)

Oil Pump Assembly

X

(Style B)

A

Remove Closure Plate Assembly

1. Remove screws securing closure plate to crankcase.

2. Locate splitting tabs cast into perimeter of closure plate. Insert drive end of a 1/2" breaker bar between top
splitting tab and crankcase. Hold handle horizontal and pull toward you to break RTV seal. If necessary, pry at
bottom tabs also. Do not pry on sealing surfaces as this could cause leaks. Carefully pull closure plate from
crankcase.

Inspection

Inspect oil seal in closure plate and remove it if it is worn or damaged. Refer to Install Closure Plate Oil Seal in
Reassembly for new oil seal installation.

Inspect main bearing surface for wear or damage. Refer to specifi cations. Replace closure plate assembly if required.

24 690 34 Rev. D KohlerEngines.com

49

Disassembly/Inspection and Service

Governor Gear Assembly

Governor Shaft Component and Details

A

B

C

A Gear Shaft

B 19.40 mm (0.7638 in.)

C 34.0 mm (1.3386 in.) 33.5 mm (1.3189 in.)

Governor gear assembly is located inside closure plate.
If service is required, refer to Inspection, Disassembly,
and Reassembly procedures.

Inspection

Inspect governor gear teeth. Replace gear if it is worn,
chipped, or if any teeth are missing. Inspect governor
weights. They should move freely in governor gear.

Disassembly

NOTE: Governor gear is held onto shaft by small

molded tabs in gear. When gear is removed from
shaft, these tabs are destroyed and gear must
be replaced. Therefore, remove gear only if
absolutely necessary.

Governor gear must be replaced once it is removed from
closure plate.

1. Remove regulating pin and governor gear assembly.

2. Remove locking tab thrust washer located under
governor gear assembly.

3. Carefully inspect governor gear shaft and replace it
only if it is damaged. After removing damaged shaft,
press or lightly tap replacement shaft into closure
plate to depth shown.

Reassembly

1. Install locking tab thrust washer on governor gear
shaft with tab down.

2. Position regulating pin within governor gear/fl yweight
assembly and slide both onto governor shaft.

Oil Pump Assembly (Style A)

Oil Pump (Style A) Torque Sequence

1

2

Oil pump is mounted inside closure plate. If service
is required, refer to Disassembly, Inspection, and
Reassembly.

Disassembly

1. Remove screws.

2. Remove oil pump assembly from closure plate.

3. Remove oil pump rotor. Unhook locking clip, and
carefully pull it free from oil pump housing.

Relief valve is a one-piece style, staked to oil pump

housing. Removal should not be attempted, nor is
internal servicing possible. If a problem with relief
valve is encountered, oil pump should be replaced.

Inspection

Inspect oil pump housing, gear, and rotors for nicks,
burrs, wear, or any visible damage. If any parts are worn
or damaged, replace oil pump. Check oil pickup screen
for damage or restriction, replace if necessary.

Reassembly

1. Install oil pickup to oil pump body. Lubricate O-ring
with oil and make sure it remains in groove as
pickup is being installed.

2. Install rotor.

3. Install oil pump body to closure plate and secure
with screws. Torque screws as follows:

a. Install fastener into screw location 1 and lightly

tighten to position pump.

b. Install fastener into screw location 2 and fully

torque to recommended value.

c. Torque fastener in screw location 1 to

recommended value.
First Time Installation: 10.7 N·m (95 in. lb.)
All Reinstallations: 6.7 N·m (60 in. lb.)

4. After torquing, rotate gear and check for freedom of

movement. Make sure there is no binding. If binding
occurs, loosen screws, reposition pump, retorque
screws and recheck movement.

50

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

Remove Oil Pump (Style B)

Oil pump is mounted inside closure plate. If service
is required, refer to Disassembly, Inspection, and
Reassembly.

Disassembly

1. Remove screws.

2. Lift oil pump assembly from closure plate. Remove
outer gerotor gear from closure plate.

3. Ensure ball and spring remain installed in pressure
relief hole of closure plate. If ball and spring fall out
of pressure relief hole, see reassembly for correct
installation.

4. Remove oil pump cover O-ring from groove in
closure plate.

Inspection

Inspect oil pump housing, gear, and rotors for nicks,
burrs, wear, or any visible damage. Inspect oil pump
cover O-ring for cuts, nicks, or any visible damage. If any
parts are worn or damaged, replace oil pump assembly
and/or O-ring. Check oil pickup screen for damage or
restriction, replace if necessary.

Reassembly

1. Lubricate outer gerotor gear with oil. Install outer
gerotor gear through shaft of oil pump, around inner
gerotor gear. Matching molding dots on inner and
outer gerotor gears is not necessary and will not
affect oil pump effi ciency.

2. Reinstall ball, then spring into pressure relief hole in
closure plate.

3. Reinstall O-ring into groove in closure plate; make
sure it is fully seated in groove.

3. Install oil pump inserting center shaft into
corresponding recess in closure plate. Apply
consistent downward pressure to oil pump cover,
compressing oil pressure relief spring and start
screws. Secure oil pump by torquing screws (in no
specifi c sequence) to 9.0 N·m (80 in. lb.).

4. After torquing, rotate gear and check for freedom of
movement. Make sure there is no binding. If binding
occurs, loosen screws, reposition pump, retorque
screws and recheck movement.

Remove Connecting Rods with Pistons and Rings

NOTE: If a carbon ridge is present at top of either

cylinder bore, use a ridge reamer tool to remove
ridge before attempting to remove piston.

NOTE: Cylinders are numbered on crankcase. Use

numbers to mark each end cap, connecting rod
and piston for reassembly. Do not mix end caps
and connecting rods.

1. Remove screws securing closest connecting rod end
cap. Remove end cap.

2. Carefully remove connecting rod and piston
assembly from cylinder bore.

3. Repeat above procedures for other connecting rod
and piston assembly.

Piston and Rings

Piston and Rings Components and Details

A

B

C

D

F

E

A Piston B

Middle Compression

C

E Expander F

Ring

Top Compression

Ring

D Rails

Oil Control Ring

(3 Piece)

Remove Camshaft

Remove camshaft.

Inspection and Service

NOTE: To prevent repeat failures, camshaft and

crankshaft should always be replaced as a set.

Check lobes of camshaft for wear or damage. See
Specifi cations for minimum lift tolerance. Inspect
cam gear for badly worn, chipped or missing teeth.
Replacement of camshaft will be necessary if any of
these conditions exist.

24 690 34 Rev. D KohlerEngines.com

51

Disassembly/Inspection and Service

NOTE: Rings must be installed correctly. Ring

installation instructions are usually included with
new ring sets. Follow instructions carefully. Use
a piston ring expander to install rings. Install
bottom (oil control) ring fi rst and top
compression ring last.

Scuffi ng and scoring of pistons and cylinder walls occurs
when internal engine temperatures approach welding
point of piston. Temperatures high enough to do this are
created by friction, which is usually attributed to improper
lubrication and/or overheating of engine.

Normally, very little wear takes place in piston boss­piston pin area. If original piston and connecting rod can
be reused after new rings are installed, original pin can
also be reused but new piston pin retainers are required.
Piston pin is included as part of piston assembly – if pin
boss in piston or pin are worn or damaged, a new piston
assembly is required.

Ring failure is usually indicated by excessive oil
consumption and blue exhaust smoke. When rings fail,
oil is allowed to enter combustion chamber where it is
burned along with fuel. High oil consumption can also
occur when piston ring end gap is incorrect because
ring cannot properly conform to cylinder wall under this
condition. Oil control is also lost when ring gaps are not
staggered during installation.

When cylinder temperatures get too high, lacquer and
varnish collect on pistons causing rings to stick, which
results in rapid wear. A worn ring usually takes on a
shiny or bright appearance.

Scratches on rings and pistons are caused by abrasive
material such as carbon, dirt, or pieces of hard metal.

Detonation damage occurs when a portion of fuel charge
ignites spontaneously from heat and pressure shortly
after ignition. This creates two fl ame fronts which meet
and explode to create extreme hammering pressures on
a specifi c area of piston. Detonation generally occurs
from using low octane fuels.

Preignition or ignition of fuel charge before timed spark
can cause damage similar to detonation. Preignition
damage is often more severe than detonation damage.
Preignition is caused by a hot spot in combustion
chamber from sources such as glowing carbon deposits,
blocked cooling fi ns, an improperly seated valve, or
wrong spark plug(s).

Replacement pistons are available in STD bore size, and
in 0.25 mm (0.010 in.), and 0.50 mm (0.020 in.) oversize.
Replacement pistons include new piston ring sets and
new piston pins.

Replacement ring sets are also available separately
for STD, 0.25 mm (0.010 in.), and 0.50 mm (0.020 in.)
oversize pistons. Always use new piston rings when
installing pistons. Never use old rings.

Some important points to remember when servicing
piston rings:

1. Cylinder bore must be deglazed before service ring
sets are used.

2. If cylinder bore does not need reboring and if old
piston is within wear limits and free of score or scuff
marks, old piston may be reused.

3. Remove old rings and clean up grooves. Never
reuse old rings.

4. Before installing new rings on piston, place top two
rings, each in turn, in its running area in cylinder
bore and check end gap. Compare ring gap to
tolerances listed in Specifi cations.

5. After installing new compression (top and middle)
rings on piston, check piston-to-ring side clearance.
Compare clearance to tolerance listed in
Specifi cations. If side clearance is greater than
specifi ed, a new piston must be used.

Install New Piston Rings

Piston Ring Orientation

E

F

A

D

10°

10°

B

C

Top Oil Ring Rail

A

Intermediate Ring

C

Gap

Gap

Bottom Oil Ring Rail

B

Oil Ring Expander

D

Gap

Gap

E Top Ring Gap F FLY Stamp

NOTE: Rings must be installed correctly. Ring

installation instructions are usually included with
new ring sets. Follow instructions carefully. Use
a piston ring expander to install rings. Install
bottom (oil control) ring fi rst and top
compression ring last.

To install new piston rings, proceed as follows:

1. Oil control ring (bottom groove): Install expander and
then rails. Make sure ends of expander are not
overlapped.

2. Middle compression ring (center groove): Install
center ring using a piston ring installation tool. Make
sure identifi cation mark is up or colored dye stripe
(if contained), is to left of end gap.

3. Top compression ring (top groove): Install top ring
using a piston ring expander. Make sure
identifi cation mark is up or colored dye stripe
(if contained), is to left of end gap.

52

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

Connecting Rods

Offset, stepped-cap connecting rods are used in all
these engines.

Inspection and Service

Check bearing area (big end) for excessive wear,
score marks, running and side clearances (refer to
Specifi cations). Replace rod and cap if scored or
excessively worn.

Service replacement connecting rods are available in
STD crankpin size and 0.25 mm (0.010 in.) undersize.
An 0.25 mm (0.010 in.) undersized rod can be identifi ed
by a drilled hole located in lower end of rod shank.
Always refer to appropriate parts information to ensure
correct replacements are used.

Remove Crankshaft

Inspection and Service
Crankshaft Components and Details

A

B

C

D

A Self-Tapping Screw B Flat Washer

C Plug D Crankshaft

F

Carefully pull crankshaft from crankcase. Note thrust
washers and shims if used.

Inspect gear teeth of crankshaft. If teeth are badly worn,
chipped, or some are missing, replacement of crankshaft
will be necessary.

Inspect crankshaft bearing surfaces for scoring,
grooving, etc. Some engines have bearing inserts in
crankshaft bore of closure plate and/or crankcase.
Do not replace bearings unless they show signs of
damage or are out of running clearance specifi cations. If
crankshaft turns easily and noiselessly, and there is no
evidence of scoring, grooving, etc., on races or bearing
surfaces, bearings can be reused.

Inspect crankshaft keyways. If they are worn or chipped,
replacement of crankshaft will be necessary.

Inspect crankpin for score marks or metallic pickup.
Slight score marks can be cleaned with crocus cloth
soaked in oil. If wear limits, as stated in Specifi cations
and Tolerances are exceeded, it will be necessary to
either replace crankshaft or regrind crankpin to 0.25 mm
(0.010 in.) undersize. If reground, a 0.25 mm (0.010 in.)
undersize connecting rod (big end) must then be used to
achieve proper running clearance. Measure crankpin for
size, taper, and out-of-round.

Connecting rod journal can be ground one size under.
When grinding a crankshaft, grinding stone deposits
can get caught in oil passages, which could cause
severe engine damage. Removing crankpin plug when
crankshaft is ground provides easy access for removing
any grinding deposits collected in oil passages.

Use following procedure to remove and replace plug.

Procedure to Remove Crankshaft Plug:

1. Drill a 3/16" hole through plug in crankshaft.

2. Thread a 3/4" or 1" long self-tapping screw with a fl at

washer into drilled hole. Flat washer must be large
enough to seat against shoulder of plug bore.

3. Tighten self-tapping screw until it draws plug out of

crankshaft.

Procedure to Install New Plug:

Use 1 single cylinder camshaft pin as a driver and tap
plug into plug bore until it seats at bottom of bore. Make
sure plug is tapped in evenly to prevent leakage.

G

E

H

Fillet Must Blend Smoothly with Bearing Journal

E

F High Point from Fillet Intersections

G 45° Minimum

H This Fillet Area Must Be Completely Smooth

NOTE: If crankpin is reground, visually check to ensure

fi llet blends smoothly with crankpin surface.

NOTE: To prevent repeat failures, camshaft and

crankshaft should always be replaced as a set.

24 690 34 Rev. D KohlerEngines.com

Surface

53

Disassembly/Inspection and Service

Remove Governor Cross Shaft

1. Remove hitch pin and plain washer, or retainer and
nylon washer from governor cross shaft.

2. Pull cross shaft with small washer out through inside
of crankcase.

Governor Cross Shaft Oil Seal

Cross Shaft Oil Seal Details

A

B

Crankcase

Inspection and Service

Check all gasket surfaces to make sure they are free of
gasket fragments. Gasket surfaces must also be free of
deep scratches or nicks.

Inspect main bearing (if equipped) for wear or damage.
Replace crankcase using a miniblock or short block as
required.

Check cylinder bore wall for scoring. In severe cases,
unburned fuel can cause scuffi ng and scoring of cylinder
wall. It washes necessary lubricating oils off piston and
cylinder wall. As raw fuel seeps down cylinder wall,
piston rings make metal to metal contact with wall.
Scoring of cylinder wall can also be caused by localized
hot spots resulting from blocked cooling fi ns or from
inadequate or contaminated lubrication.

If cylinder bore is badly scored, excessively worn,
tapered, or out-of-round, resizing is necessary. Use an
inside micrometer to determine amount of wear (refer
to Specifi cations), then select nearest suitable oversize
of either 0.25 mm (0.010 in.) or 0.50 mm (0.020 in.).
Resizing to one of these oversizes will allow usage of
available oversize piston and ring assemblies. First,
resize using a boring bar, then follow these procedures
for honing cylinder.

A 2.0 mm (0.0787 in.)

B Governor Cross Shaft Seal

If governor cross shaft seal is damaged and/or leaks,
replace it using following procedure.

Remove oil seal from crankcase and replace it with a
new one. Install new seal to depth shown using a seal
installer.

Remove Flywheel End Oil Seal

Remove oil seal from crankcase.

54

KohlerEngines.com 24 690 34 Rev. D

Disassembly/Inspection and Service

Honing
Detail

A

A 23°-33° Crosshatch

NOTE: Kohler pistons are custom-machined to exacting

tolerances. When oversizing a cylinder, it should
be machined exactly 0.25 mm (0.010 in.) or 0.50
mm (0.020 in.) over new diameter (refer to
Specifi cations). A corresponding oversize Kohler
replacement piston will then fi t correctly.

While most commercially available cylinder hones can
be used with either portable drills or drill presses, use
of a low speed drill press is preferred as it facilitates
more accurate alignment of bore in relation to crankshaft
crossbore. Honing is best accomplished at a drill speed
of about 250 RPM and 60 strokes per minute. After
installing coarse stones in hone, proceed as follows:

1. Lower hone into bore and after centering, adjust so

stones are in contact with cylinder wall. Use of a
commercial cutting-cooling agent is recommended.

2. With lower edge of each stone positioned even with

lowest edge of bore, start drill and honing process.
Move hone up and down while resizing to prevent
formation of cutting ridges. Check size frequently.

3. When bore is within 0.064 mm (0.0025 in.) of

desired size, remove coarse stones and replace
them with burnishing stones. Continue with
burnishing stones until bore is within 0.013 mm
(0.0005 in.) of desired size and then use fi nish
stones (220-280 grit) and polish bore to its fi nal size.
A crosshatch should be observed if honing is done
correctly. Crosshatch should intersect at
approximately 23°-33° off horizontal. Too fl at an
angle could cause rings to skip and wear
excessively, and too steep an angle will result in high
oil consumption.

4. After resizing, check bore for roundness, taper, and

size. Use an inside micrometer, telescoping gauge,
or bore gauge to take measurements. These
measurements should be taken at 3 locations in
cylinder–at top, middle, and bottom. There are 2
measurements that should be taken (perpendicular
to each other) at all 3 locations.

Clean Cylinder Bore After Honing

Proper cleaning of cylinder walls following boring and/
or honing is very critical to a successful overhaul.
Machining grit left in cylinder bore can destroy an engine
in less than one hour of operation after a rebuild.

Final cleaning operation should always be a thorough
scrubbing with a brush and hot, soapy water. Use a
strong detergent capable of breaking down machining
oil while maintaining a good level of suds. If suds break
down during cleaning, discard dirty water and start again
with more hot water and detergent. Following scrubbing,
rinse cylinder with very hot, clear water, dry it completely,
and apply a light coating of engine oil to prevent rusting.

Measuring Piston-to-Bore Clearance
Piston Detail

A

Model Dimension A

CH682 13 mm (0.5118 in.)

CH732

6 mm (0.2362 in.)CH742

CH752

NOTE: Do not use a feeler gauge to measure piston-to-

bore clearance–it will yield inaccurate
measurements. Always use a micrometer.

Before installing piston into cylinder bore, it is
necessary clearance be accurately checked. This step
is often overlooked, and if clearances are not within
specifi cations, engine failure will usually result.

Use following procedure to accurately measure piston­to-bore clearance:

1. Use a micrometer and measure diameter of piston
above bottom of piston skirt and perpendicular to
piston pin.

2. Use an inside micrometer, telescoping gauge, or
bore gauge and measure cylinder bore. Take
measurement approximately 63.5 mm (2.5 in.) below
top of bore and perpendicular to piston pin.

3. Piston-to-bore clearance is difference between bore
diameter and piston diameter (step 2 minus step 1).

24 690 34 Rev. D KohlerEngines.com

55

Reassembly

Crankcase Components

R

V

K

T

U

A

Q

A Oil Seal B Closure Plate (Style A) C

E

M Piston N Connecting Rod O

Q Crankcase R Governor Cross Shaft S Closure Plate (Style B) T

U Ball (Style B) V Spring (Style B) W

Y

NOTE: Make sure engine is assembled using all

Make sure all traces of any cleaner are removed before
engine is assembled and placed into operation. Even
small amounts of these cleaners can quickly break down
lubricating properties of engine oil.

Oil Pick-Up Tube

(Style A)

I Camshaft J Piston Pin K Piston Ring Set L Piston Pin Retainer

Oil Pick-Up Tube

(Style B)

specifi ed torque values, tightening sequences
and clearances. Failure to observe specifi cations
could cause severe engine wear or damage.
Always use new gaskets. Apply a small amount
of oil to threads of critical fasteners before
assembly, unless a sealant or Loctite® is
specifi ed or preapplied.

N

O

P

Oil Pump Assembly

F

M

(Style A)

J

X

W

L

H

G

I

F

E

Gerotor Gears (Style

A)

G Governor Gear Shaft H Governor Gear

Connecting Rod End

Cap

Oil Pump Cover O-ring

(Style B)

Check closure plate, crankcase, cylinder heads, and
valve covers to be certain all old sealing material has
been removed. Use gasket remover, lacquer thinner, or
paint remover to remove any remaining traces. Clean
surfaces with isopropyl alcohol, acetone, lacquer thinner,
or electrical contact cleaner.

Install Flywheel End Oil Seal

1. Make sure seal bore of crankcase is clean and free
of any nicks or burrs.

2. Apply a light coat of clean engine oil to outside
diameter of oil seal.

3. Drive oil seal into crankcase using a seal driver.
Make sure oil seal is installed straight and true in
bore and tool bottoms against crankcase.

Y

S

D

C

B

D Dipstick Tube

P Crankshaft

Outer Gerotor Gear

(Style B)

Oil Pump Assembly

X

(Style B)

A

56 24 690 34 Rev. DKohlerEngines.com

Reassembly

Install Governor Cross Shaft

1. Lubricate governor cross shaft bearing surfaces in
crankcase with engine oil.

2. Slide small lower washer onto governor cross shaft
and install cross shaft from inside of crankcase.

3. Install nylon washer onto governor cross shaft, then
start push-on retaining ring. Hold cross shaft up in
position, place a 0.50 mm (0.020 in.) feeler gauge on
top of nylon washer, and push retaining ring down
shaft to secure. Remove feeler gauge, which will
have established proper end play.

Install Crankshaft

Carefully slide fl ywheel end of crankshaft through main
bearing in crankcase.

Install Connecting Rods with Pistons and Rings

Piston and Connecting Rod Details

B

4. Make sure FLY stamping on piston is facing towards
fl ywheel side of engine. Use a hammer with a rubber
grip and gently tap piston into cylinder as shown. Be
careful oil ring rails do not spring free between
bottom of ring compressor and top of cylinder.

5. Install inner rod cap to connecting rod using screws.
Torque in increments to 13.6 N·m (120 in. lb.).
Illustrated instructions are provided in service rod
package.

6. Repeat above procedure for other connecting rod
and piston assembly.

Install Camshaft

1. Liberally apply camshaft lubricant to each cam lobe.
Lubricate camshaft bearing surfaces of crankcase
and camshaft with engine oil.

2. Position timing mark of crankshaft gear at 12 o’clock
position.

3. Turn governor cross shaft clockwise until lower end
of shaft contacts cylinder. Make sure cross shaft
remains in this position while installing camshaft.

4. Slide camshaft into bearing surface of crankcase,
positioning timing mark of camshaft gear at 6 o’clock
position. Make sure camshaft gear and crankshaft
gear mesh, with both timing marks aligned.

Oil Pump Assembly

Oil pump is mounted inside closure plate. If service was
required, and oil pump was removed, refer to
Disassembly/Inspection and Service.

A

A Cylinder 1 B Cylinder 2

NOTE: Cylinders are numbered on crankcase. Make

sure to install piston, connecting rod and end
cap into its appropriate cylinder bore as
previously marked at disassembly. Do not mix
end caps and connecting rods.

NOTE: Proper orientation of piston/connecting rod

assemblies inside engine is extremely important.
Improper orientation can cause extensive wear
or damage. Be certain pistons and connecting
rods are assembled exactly as shown.

NOTE: Align chamfer of connecting rod with chamfer of

its mating end cap. When installed, fl at faces of
connecting rods should face each other. Faces
with raised rib should be toward outside.

1. If piston rings were removed, see Disassembly/
Inspection and Service procedure to install new
rings.

2. Lubricate cylinder bore, piston, and piston rings with
engine oil. Compress rings of piston 1 using a piston
ring compressor.

3. Lubricate crankshaft journals and connecting rod
bearing surfaces with engine oil.

Governor Gear Assembly

Governor gear assembly is located inside closure plate.
If service was required, and governor was removed,
refer to Disassembly/Inspection and Service.

5724 690 34 Rev. D KohlerEngines.com

Reassembly

Thrust Bearing, Washer and Shim

A

B

C

D

E

A Thrust Shim B Thrust Washer

C

E Closure Plate

Some specifi cations use a needle type thrust bearing,
thrust washer and shim spacer to control end play of
crankshaft. If these items are noted during disassembly,
make sure they are reinstalled in sequence shown. A
different procedure will have to be followed to check and
adjust crankshaft end play on these models.

Race for thrust bearing presses loosely into closure
plate. If it is not already installed, push it into crankshaft
bore inside closure plate. Pack thrust bearing with heavy
grease and stick bearing into race. Wipe some grease
on face of thrust washer and stick it onto thrust bearing.
Wipe some grease on face of original shim spacer and
stick it onto thrust washer.

Install closure plate onto crankcase without applying
RTV sealant and secure it with only 2 or 3 fasteners at
this time. Use a dial indicator to check crankshaft end
play. End play should be 0.070/1.190 mm
(0.0028/0.0468 in.). Shim spacers are available in 3
color coded thicknesses if adjustment is needed.

Clearance Specifi cations-Crankshaft End Play Shims

Green 0.8366-0.9127 mm

Yellow 1.0652-1.1414 mm

Red 1.2938-1.3700 mm

Remove closure plate. If end play requires adjustment,
remove original spacer and install appropriate size shim
spacer in its place. Then follow procedure under Install
Closure Plate Assembly.

Needle Thrust

Bearing

(0.8750 mm/0.034 in. Nominal)

(1.1033 mm/0.043 in. Nominal)

(1.3319 mm/0.052 in. Nominal)

D Bearing Race

Install Closure Plate Oil Seal

Oil Seal Depth

A

B

A Oil Seal B

1. Check to make sure there are no nicks or burrs in
crankshaft bore of closure plate.

2. Apply a light coat of engine oil to outside diameter of
oil seal.

3. Drive oil seal into closure plate using a seal driver.
Make sure oil seal is installed straight and true in
bore to depth shown.

Seal Depth

8.0 mm (0.314 in.)

58 24 690 34 Rev. DKohlerEngines.com

Reassembly

Install Closure Plate Assembly

Sealant Pattern and Torque Sequence

3

5

7

9

Flywheel/Ignition Components

RTV sealant is used as a gasket between closure plate
and crankcase. Always use fresh sealant. Using
outdated sealant can result in leakage.

1

10

1. Be sure sealing surfaces have been cleaned and

prepared. Install a new O-ring in closure plate.

2. Check to make sure there are no nicks or burrs on

sealing surfaces of closure plate or crankcase.

3. Apply a 1.5 mm (1/16 in.) bead of sealant to sealing

8

surface of closure plate.

4. Make sure end of governor cross shaft is lying

against bottom of cylinder 1 inside crankcase.

5. Install closure plate to crankcase. Carefully seat

camshaft and crankshaft into their mating bearings.

6

Rotate crankshaft slightly to help engage oil pump
and governor gear meshes.

6. Install screws securing closure plate to crankcase.

42

Torque fasteners to 24.4 N·m (216 in. lb.) following
sequence. On some engines one mounting screw is
plated. Plated screw is typically installed in hole
location 6.

J

I

P

K

L

H

M

D

C

B

F

G

E

A Debris Screen B Fan C Flywheel Screw D Washer

E Flywheel F Magnet G Stator H Ignition Module

I Backing Plate J Woodruff Key K Spring Washer L Spacer

M Ring Support N Metal Debris Screen O Washer P

Install Stator and Backing Plates

1. Apply pipe sealant with Tefl on

®

(Loctite® 592™
Thread Sealant or equivalent) to stator mounting
holes.

3. Install and torque screws to 6.2 N·m (55 in. lb.).

4. Route stator leads in crankcase channel, then install
backing plates and stator wire bracket (if used).
Secure using screws. Torque screws to 7.3 N·m
(65 in. lb.).

Metal Debris Screen

Assembly

2. Position stator aligning mounting holes so leads are
at bottom, towards crankcase.

O

N

A

5924 690 34 Rev. D KohlerEngines.com

Reassembly

Install Flywheel

CAUTION

Damaging Crankshaft and Flywheel can
cause personal injury.

Using improper procedures can lead to broken
fragments. Broken fragments could be thrown from
engine. Always observe and use precautions and
procedures when installing fl ywheel.

NOTE: Before installing fl ywheel make sure crankshaft

taper and fl ywheel hub are clean, dry, and
completely free of any lubricants. Presence of
lubricants can cause fl ywheel to be over
stressed and damaged when screw is torqued to
specifi cations.

NOTE: Make sure fl ywheel key is installed properly in

keyway. Flywheel can become cracked or
damaged if key is not properly installed.

1. Install woodruff key into keyway of crankshaft. Make
sure key is properly seated and parallel with shaft
taper.

2. Install fl ywheel onto crankshaft being careful not to
shift woodruff key.

3. Install screw and washer.

4. Use a fl ywheel strap wrench or holding tool to hold
fl ywheel. Torque screw securing fl ywheel to
crankshaft to 66.4 N·m (49 ft. lb.).

Install Plastic Debris Screen

CAUTION

Failure to utilize or reassemble debris screen
as designed could result in debris screen
failure and serious personal injury.

If engine has a plastic debris screen, place plastic
screen on fan and secure with screws. Torque screws to

4.0 N·m (35 in. lb.).

Install Supports for Metal Debris Screen

1. If a metal debris screen is used, with threaded
individual supports, install a spacer washer on
external threads. Apply Loctite® 242® (removable)
onto threads. Install four supports as shown.

2. Tighten supports with a torque wrench to 9.9 N·m
(88 in. lb.). Debris screen will be installed to supports
after blower housing is in place.

Install Flywheel Fan

NOTE: Position ears located at rear perimeter of fan in

recesses of fl ywheel.

1. Install fan onto fl ywheel using four screws.

2. Torque screws to 9.9 N·m (88 in. lb.).

60 24 690 34 Rev. DKohlerEngines.com

Cylinder Head Components

Reassembly

K

G

J

I

H

F

E

B

D

A

A Valve B Stud C Gasket D Spark Plug

E Cap F Valve Stem Seal G Hydraulic Lifter H Retainer

I Valve Spring J Valve Spring Retainer K Push Rod L Valve Keeper

M Rocker Arm N Rocker Arm Pivot O Valve Cover O-ring P Valve Cover

Install Hydraulic Lifters

NOTE: Hydraulic lifters should always be installed in

same position as before disassembly. Exhaust
lifters are located on output shaft side of engine
while intake lifters are located on fan side of
engine. Cylinder numbers are embossed on top
of crankcase and each cylinder head.

1. Refer to Disassembly/Inspection and Service for
lifter preparation (bleed down) procedures.

2. Apply camshaft lubricant to bottom surface of each
lifter. Lubricate hydraulic lifters and lifter bores in
crankcase with engine oil.

3. Note mark or tag identifying hydraulic lifters as either
intake or exhaust and cylinder 1 or cylinder 2. Install
hydraulic lifters into their appropriate location in
crankcase. Do not use a magnet.

C

Assemble Cylinder Heads

Prior to installation, lubricate all components with engine
oil, paying particular attention to lip of valve stem seal,
valve stems and valve guides. Install in order listed
below using a valve spring compressor.

● Intake and exhaust valves.

● Valve spring caps.

● Valve springs.

● Valve spring retainers.

● Valve spring keepers.

N

M

L

P

O

Valve Stem Seals

These engines use valve stem seals on intake valves
and occasionally on exhaust valves. Always use a new
seal whenever valve is removed or if seal is deteriorated
or damaged in any way. Never reuse an old seal.

6124 690 34 Rev. D KohlerEngines.com

Reassembly

Install Cylinder Heads

Cylinder Head Torque Sequence

3

2

NOTE: Cylinder heads must be attached with original

type of mounting hardware, using either screws,
or mounting studs with nuts and washers. Heads
are machined differently for studs than for
screws, so fastening method cannot be altered
unless heads are being replaced. Do not
intermix components.

Heads secured with screws:

NOTE: Match numbers embossed on cylinder heads

and crankcase.

1. Check to make sure there are no nicks or burrs on
sealing surfaces of cylinder head or crankcase.

2. Install a new cylinder head gasket, (with printing up).

3. Install cylinder head and start four screws.

4. Torque screws in two stages; fi rst to 22.6 N·m
(200 in. lb.), fi nally to 41.8 N·m (370 in. lb.), following
sequence shown.

Heads secured with mounting studs, nuts, and
washers:

1. Check to make sure there are no nicks or burrs on
sealing surfaces of cylinder head or crankcase.

2. If all studs were left intact, go to Step 5. If any studs
were disturbed or removed, install new studs as
described in Step 3. Do not use/reinstall any
loosened or removed studs.

3. Install new mounting stud(s) into crankcase.

a. Thread and lock two mounting nuts together on

smaller diameter threads.

b. Thread opposite end of stud with preapplied

locking compound into crankcase until specifi ed
height from crankcase surface is achieved.
When threading in studs, use a steady tightening
motion without interruption until proper height is
obtained. Otherwise, frictional heat from
engaging threads may cause locking compound
to set up prematurely.

Studs closest to lifters must have an exposed

height of 75 mm (2 15/16 in.).

Studs furthest from lifters must have an exposed

height of 69 mm (2 3/4 in.).

c. Remove nuts and repeat procedure as required.

1

4

1

4

3

2

21

4. Install cylinder head. Match numbers on cylinder
heads and crankcase. Make sure head is fl at on
gasket and dowel pins.

5. Lightly lubricate exposed (upper) threads of studs
with engine oil. Install a new fl at washer and nut onto
each mounting stud. Torque nuts in two stages; fi rst
to 16.9 N·m (150 in. lb.), fi nally to 35.5 N·m
(315 in. lb.), following sequence shown.

Install Push Rods and Rocker Arms

NOTE: Push rods should always be installed in same

position as before disassembly.

1. Note mark or tag identifying push rod as either
intake or exhaust and cylinder 1 or 2. Dip ends of
push rods in engine oil and install, making sure each
push rod ball seats in its hydraulic lifter socket.

2. Apply grease to contact surfaces of rocker arms and
rocker arm pivots. Install rocker arms and rocker arm
pivots on one cylinder head, and start two screws.

3. Torque screws to 18.1 N·m (160 in. lb.). Repeat for
other rocker arm.

4. Use a spanner wrench or rocker arm lifting tool to lift
rocker arms and position push rods underneath.

5. Repeat above steps for remaining cylinder. Do not
interchange parts from cylinder heads.

6. Rotate crankshaft to check for free operation of
valve train. Check clearance between valve spring
coils at full lift. Minimum allowable clearance is

0.25 mm (0.010 in.).

Check Assembly

Rotate crankshaft a minimum of two revolutions to check
longblock assembly and overall proper operation.

Install Spark Plugs

1. Check gap using wire feeler gauge. Adjust gap to

0.76 mm (0.03 in.).

2. Install plug into cylinder head.

3. Torque plug to 27 N·m (20 ft. lb.).

62 24 690 34 Rev. DKohlerEngines.com

Reassembly

Install Ignition Modules

1. Rotate fl ywheel to position magnet away from
ignition module bosses.

2. CDI modules are installed with spark plug lead wire
from module always away from cylinder. On cylinder
1, single kill tab should be towards you. On cylinder
2, single kill tab should be away from you (in).

MDI modules are installed with fl at side out/towards

you.

3. Install each ignition module to crankcase bosses.
Slide modules up as far away from fl ywheel as
possible and snug screws to hold them in position.

4. Rotate fl ywheel to position magnet directly under
one ignition module.

5. Insert a 0.25 mm (0.009 in.) fl at feeler gauge
between magnet and ignition module. Loosen
screws enough to allow magnet to pull module down
against feeler gauge.

6. Torque screws to 4.0-6.2 N·m (35-55 in. lb.).

7. Repeat steps 4 through 6 for other ignition module.

8. Rotate fl ywheel back and forth checking for
clearance between magnet and ignition modules.
Make sure magnet does not strike modules. Check
gap with a feeler gauge and readjust if necessary.

Final air gap is: 0.203/0.305 mm (0.008/0.012 in.).

Install Intake Manifold

Torque Sequence

3

1

1. Install intake manifold and new gaskets, with wiring
harness attached, to cylinder heads. Slide any wiring
harness clips onto appropriate bolts before installing.
Make sure gaskets are in proper orientation. Torque
screws in two stages, fi rst to 7.4 N·m (66 in. lb.),
then to 9.9 N·m (88 in. lb.), using sequence shown.

2. Route wiring harness through mounting clip on
underside of debris shield if separated earlier.
Carefully position debris shield as rearward as
possible.

3. Connect each kill lead to tab terminal on each
ignition module.

2

4

6324 690 34 Rev. D KohlerEngines.com

Reassembly

External Engine Components

E

D

C

A

F

X

G

H

I

J

K

L

V

M

B

K

W

R

F

Q

S

T

P

O

N

A Intake Manifold B

E Air Cleaner Gasket F Outer Baffl e G Breather Tube H Oil Sentry

Intake Manifold

Gasket

C Carburetor Gasket D Carburetor

™

I Breather Cover J Breather Gasket K Inner Baffl e L Breather Reed

M Filter N Electric Starter O Lifting Bracket P Fixed Guard

Q Blower Housing R Wire Clip S Oil Filter T Nipple

U Oil Cooler V

Valve Cover Fuel

Pump

W Pulse Fuel Pump X Air Cleaner

U

64 24 690 34 Rev. DKohlerEngines.com

Reassembly

Install Breather Cover and Inner Baffl es

Breather Cover Torque Sequence

1

3

4

1. Be sure sealing surfaces of crankcase and breather
cover are clean of old gasket material. Do not scrape
surfaces as this could result in leakage.

2. Check to make sure there are no nicks or burrs on
sealing surfaces.

3. Install breather reed and breather reed retainer onto
crankcase and secure with screw. Hold assembly in
line when tightening. Torque screw to 3.9 N·m
(35 in. lb.).

4. Insert breather fi lter into position in crankcase. Make
sure no fi lter strands are on sealing surface.

5. Install new breather gasket.

6. Carefully position breather cover on crankcase.
Install fi rst two screws at positions shown and fi nger
tighten at this time.

7. Install inner baffl es using two remaining screws and
fi nger tighten. Do not torque screws at this time; they
will be tightened after blower housing and outer
baffl es are installed.

Install Blower Housing and Outer Baffl es

NOTE: Do not completely tighten screws until all items

are installed to allow shifting for hole alignment.

1. Connect plug to key switch in blower housing (if
equipped).

2. Slide blower housing into position over front edge of
inner baffl es. Start a few screws to hold it in place.
Lift debris shield up above mounting surface, as
blower housing is installed. Make sure ground lead,
fuel solenoid lead, and oil pressure switch leads are
accessible and in proper position.

3. Position outer baffl es and loosely start mounting
screws. M6 screws go into back of cylinders. Short
M5 screws go into lower holes closest to blower
housing. Short screw on oil fi lter side is also used to
mount wire harness clip. Be sure any wire harnesses
or leads are routed out through proper offsets or
notches, so they will not be pinched between blower
housing and baffl es.

2

4. If rectifi er-regulator was not removed, attach ground
wire or metal grounding bracket for rectifi er-
regulator, using silver colored screw and washer, to
lower blower housing hole.

5. Tighten all shrouding fasteners. Torque blower
housing screws to 6.2 N·m (55 in. lb.) in a new hole,
or to 4.0 N·m (35 in. lb.) in a used hole. Torque
shorter M5 side baffl e screws to 4.0 N·m (35 in. lb.).
Torque upper M5 side baffl e screws (into cylinder
head) to 6.2 N·m (55 in. lb.) in a new hole, or to 4.0
N·m (35 in. lb.) in a used hole. Torque two rear M6
baffl e mounting screws to 10.7 N·m (95 in. lb.) in a
new hole, or to 7.3 N·m (65 in. lb.) in a used hole.

6. If an overlapping style fl ywheel screen is used,
attach it to supports or fl ywheel. For a metal fl ywheel
screen, apply Loctite® 242® to screw threads (M6)
and torque to 9.9 N·m (88 in. lb.). Torque plastic
screen mounting screws (M4) to 2.2 N·m (20 in. lb.).

7. Torque breather cover screws to 11.3 N·m (100 in.
lb.) into new holes or 7.3 N·m (65 in. lb.) into used
holes in sequence shown. Note fi rst screw is torqued
a second time.

Reconnect Rectifi er-Regulator

1. Install rectifi er-regulator in blower housing, if
removed previously, then connect rectifi er-regulator
ground lead with washer and silver screw through
eyelet as shown. If a grounding bracket is used,
secure with lower mounting screw and washer,
against outer side of rectifi er-regulator.

2. Install B+ terminal/lead into center position of
rectifi er-regulator plug and connect plug to rectifi er-
regulator.

Install Electric Starter Motor

NOTE: If engine uses a side mount muffl er on starter

side, be sure to tie wires close to starter to avoid
contact with hot exhaust parts.

1. Install starter motor using two screws.

2. Torque screws to 15.3 N·m (135 in. lb.).

6524 690 34 Rev. D KohlerEngines.com

Reassembly

3. connect leads to solenoid.

Install Fuel Pump

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings,
away from sparks or fl ames. Spilled fuel could ignite if
it comes in contact with hot parts or sparks from
ignition. Never use gasoline as a cleaning agent.

NOTE: If a new fuel pump is being installed, make sure

orientation of new pump is consistent with
removed pump. Internal damage may occur if
installed incorrectly.

1. Install pulse style fuel pump and lines as an
assembly. Connect pulse line to crankcase vacuum
fi tting.

2. Install fuel pump using screws. Torque screws to

2.3 N·m (20 in. lb.).

Install Carburetor

WARNING

Explosive Fuel can cause fi res and severe
burns.

Do not fi ll fuel tank while engine is hot or
running.

Gasoline is extremely fl ammable and its vapors can
explode if ignited. Store gasoline only in approved
containers, in well ventilated, unoccupied buildings,
away from sparks or fl ames. Spilled fuel could ignite if
it comes in contact with hot parts or sparks from
ignition. Never use gasoline as a cleaning agent.

1. Use a new carburetor gasket. Make sure all holes
align and are open.

2. Apply Loctite® 242® to shorter (inner) set of threads
of any removed studs.

3. Assemble carburetor gasket and carburetor to intake
manifold, and start any removed studs. Use two
fl ange nuts locked fl ange to fl ange and tighten each
stud until bottomed/tight.

4. Connect ground lead and fuel solenoid lead as
equipped.

Control Bracket Components

B

A

G

C

F

E

D

A Choke Linkage B Control Bracket

C Governor Spring D Governor Lever

E Nut F Throttle Linkage

G

Install External Governor Controls

1. Install governor lever onto governor cross shaft.

2. Make sure throttle linkage is connected to governor

3. Move governor lever toward carburetor as far as it

4. Insert a nail into hole on cross shaft and rotate shaft

5. Reconnect lead wire to fuel shut-off solenoid if

Install Throttle & Choke Controls

1. Connect choke linkage to carburetor and choke

2. Mount main control bracket, and air cleaner support

3. Connect governor spring from main control bracket

Governed Idle

Spring

lever and throttle lever on carburetor.

will go (wide-open throttle) and hold in position.

counterclockwise as far as it will turn, then torque
nut to 6.8 N·m (60 in. lb.).

equipped.

actuator lever.

bracket (if used) to cylinder heads using four screws.
Torque screws to 10.7 N·m (95 in. lb.) into new
holes, or 7.3 N·m (65 in. lb.) into used holes.

to appropriate hole in governor lever as indicated in
applicable chart. Note that hole positions are
counted from pivot point of governor lever.

66 24 690 34 Rev. DKohlerEngines.com

Reassembly

Governor Lever Hole Position

F

A

B

C

D

E

A Governor Lever B Hole 1
C Hole 2 D Hole 3
E Hole 4 F Hole G

Governor Lever and Hole Position/RPM Chart
(Governed Idle, 10% Regulation)

Governed Idle Spring Assembled in Hole G

High Idle RPM

Gov. Lever

Hole No.

Governor Spring

Color Code

3900 3 Black
3850 3 Black
3800 2 Orange
3750 2 Orange
3700 3 Clear
3650 2 Blue
3600 2 Red
3550 2 Clear
3500 2 Clear
3450 2 Clear
3400 1 Black
3350 1 Red
3300 1 Red
3250 3 Yellow

Install Oil Sentry™ (if equipped)

1. Apply pipe sealant with Tefl on

®

(Loctite® PST® 592™
or equivalent) to threads of Oil Sentry™ switch and
install it into breather cover. Torque to 4.5 N·m
(40 in. lb.).

2. Connect wire lead (green) to Oil Sentry

terminal.

™

Install Control Panel (if equipped)

1. Install panel to blower housing.

2. Connect throttle control cable or shaft.

3. Connect choke control cable to control bracket.

4. Connect Oil Sentry™ indicator light wires.

Install Valve Covers

Torque Sequence

1

4

3

2

1. Make sure sealing surfaces are clean.

2. Make sure there are no nicks or burrs on sealing
surfaces.

3. Install a new O-ring in groove of each cover.

4. Locate cover with oil fi ll neck on same side as
removed and install lifting strap in original position.
Position cover on cylinder head. Install four screws
in each cover and fi nger tighten.

5. Torque valve cover fasteners to 6.2 N·m (55 in. lb.)
using sequence shown.

6724 690 34 Rev. D KohlerEngines.com

Reassembly

Install Air Cleaner Assembly

Torque Sequence

3, 7

2, 6

1, 5

4, 8

1. Connect breather hose to breather cover and fi tting
on adapter elbow. Route fuel line adjacent to fuel
solenoid, and secure to carburetor inlet with a clamp.

2. Install a new air cleaner gasket. Make sure all holes
align and are open.

3. Align air cleaner mounting bracket (if equipped) with
valve cover mounting holes and start screws.

4. Install air cleaner assembly onto mounting studs.
Secure with hex fl ange nuts. Torque nuts in 2
stages: fi rst to 7.3 N·m (65 in. lb.), then fi nally to

8.2 N·m (73 in. lb.), using sequence shown. Start
two mounting screws into top of intake manifold.

5. Check alignment of bracket and torque valve cover
screws as prescribed in Install Valve Covers. Torque
upper mounting screws into manifold to 9.9 N·m
(88 in. lb.).

6. Connect air cleaner hose to elbow or adapter on
carburetor and secure with a clamp.

Install Muffl er

1. Install port liners (if equipped). Install muffl er and
attaching hardware to muffl er bracket. Torque
screws to 9.9 N·m (88 in. lb.).

2. Install nuts to exhaust studs. Torque nuts to

24.4 N·m (216 in. lb.).

Install Oil Cooler (if equipped)

1. Secure adapter to closure plate with oil fi lter nipple.
Torque oil fi lter nipple to 27 N·m (20 ft. lb.).

2. Install screws and secure oil cooler to blower
housing.

Install Oil Filter and Fill Crankcase with Oil

NOTE: Make sure both oil drain plugs are installed and

torqued to specifi cations to prevent oil leakage.

1. Install oil drain plug(s). Torque plug(s) to 13.6 N·m
(10 ft. lb.). If oil drain valve is used, make sure valve
body is closed and cap is on.

2. Place new fi lter in shallow pan with open end up. Fill
with new oil until oil reaches bottom of threads. Allow
2 minutes for oil to be absorbed by fi lter material.

3. Apply a thin fi lm of clean oil to rubber gasket on oil
fi lter.

4. Refer to instructions on oil fi lter for proper
installation.

5. Fill crankcase with new oil. Level should be at top of
indicator on dipstick.

6. Reinstall oil fi ll cap/dipstick and tighten securely.

Connect Spark Plug Leads

Connect leads to spark plugs.

Prepare Engine for Operation

Engine is now completely reassembled. Before starting
or operating engine, be sure to follow these steps.

1. Make sure all hardware is tightened securely.

2. Make sure oil drain plugs, Oil Sentry
switch, and a new oil fi lter are installed.

pressure

™

3. Adjust carburetor idle speed adjusting screw as
necessary.

Testing Engine

It is recommended engine be operated on a test stand or
bench prior to installation in piece of equipment.

1. Set engine up on a test stand. Install an oil pressure
gauge. Start engine and check to be certain oil
pressure (20 psi or more) is present. Run engine at
idle for 2-3 minutes, then 5-6 minutes more between
idle and midrange. Adjust carburetor mixture settings
as necessary (as available).

2. Adjust idle speed screw and high-speed stop as
necessary. Make sure maximum engine speed does
not exceed 3750 RPM (no load).

68 24 690 34 Rev. DKohlerEngines.com

6924 690 34 Rev. D KohlerEngines.com

70 24 690 34 Rev. DKohlerEngines.com

7124 690 34 Rev. D KohlerEngines.com

1P24 690 34

© 2015 by Kohler Co. All rights reserved.

72 24 690 34 Rev. DKohlerEngines.com

8 85612 22193 3