9-IN-1 STEAM MOP
KAMOP91STMB
Please read these warnings carefully. Failure to follow these instructions may lead to product
failure or injury.
• The liquid or steam must not be directed towards equipment containing electrical
components, such as the interior of ovens.
• Unplug the appliance after use and before carrying out user maintenance on the
appliance.
• If the supply cord is damaged, it must be replaced by a Kogan customer service
technician to avoid a hazard.
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety. Children should be supervised to ensure that
they do not play with the appliance.
Safeguards
1. Verify that the main voltage indicated on the product corresponds with the voltage
of your electrical outlet. Rated voltage: 220-240V, 50/60Hz, 1300W
2. To p rovide continued protection against the risk of electric shock, only connect to
properly grounded outlets.
3. This product is designed for domestic, household use only.
4. Do not use outdoors.
5. Do not leave the steam mop unattended while plugged in. Unplug the electrical
cord when not in use and before servicing.
6. Do not allow the steam mop to be used as a toy. Young children should be
supervised to ensure that they do not play with the appliance. Close attention is
necessary when used near children, pets or plants.
7. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they are under supervision have been instructed how to use the appliance
by a person responsible for their safety.
8. Never direct steam towards people, animals or plants.
9. Do not immerse the steam mop in water or other liquids.
10. Do not use with damaged cord or plug. If the steam mop is not working as it
should, has been dropped, damaged, left outdoors or immersed in water, return it
to Kogan. If the supply cord is damaged, it must be replaced by a Kogan customer
service technician to avoid a hazard.
11. Do not pull or carry the unit by the cord, use the cord as a handle, close a door on
the cord or pull the cord around sharp edges or corners. Keep the cord away from
heated surfaces.
12. Never force the plug into an outlet.
13. Do not use telescopic cords or outlets with inadequate electrical current carrying
capacity.
14. Unplug after each use. To safely unplug, grasp the plug and gently pull, do not
unplug by pulling on the cord.
15. Do not handle the plug or the steam mop with wet hands or operate without
shoes.
16. Do not insert any objects into openings in the unit. Do not use with any opening of
the product blocked.
17. Do not use the Mop Head without a floor cloth in place.
18. Do not use without water in the Water Tank.
19. Use extra caution when using on stairs.
20. Store your steam mop indoors in a cool, dry place.
21. Keep your work area well-lit.
22. Never put hot water or any other liquids such as aromatic, alcohol-based or
detergent products into the steam mop Water Tank. This will make the operation
unsafe and damage the unit.
23. Always keep the output for the steam clear. Avoid placing the steam opening on
soft surfaces which may block the flow of steam. Keep the openings free from lint,
hair and other potential obstructions to ensure proper steam flow.
24. Use only as directed in this manual. Use the recommended accessories only.
25. Use of attachments not provided or sold by Kogan.com may cause fire, electric
shock or injury.
26. The liquid or steam should not be directed towards equipment containing electrical
components, such as the interior of ovens.
27. Do not expose to rain.
28. Stop using the steam mop if you observe water leakage and contact the Kogan
Customer support team.
29. Do not use the steam mop in enclosed spaces that are filled with flammable,
explosive or toxic vapour such as paint thinner or oil-based paint.
30. Do not use on leather, wax polished furniture or floors, unsealed hardwood or
parquet floors, synthetic fabrics, velvet or other delicate steam-sensitive materials.
31. Do not use for space heating purposes.
32. Unplug the appliance from the outlet before servicing.
33. Do not touch hot surfaces.
34. Do not place on or near a hot gas or electric burner or in a heated oven.
35. To disconnect the unit, turn the Power Switch (O/I) to the “OFF” position, turn off
the steam regulator, then remove the plug from the wall outlet.
36. Do not use the appliance for anything other than its intended use.
37. Care should be taken when using appliance due to emission of steam.
38. To avoid circuit overload, do not operate another appliance on the same socket
(circuit) as the steam cleaner.
Commercial use of this product voids the manufacturer warranty.
Save a copy of these instructions for future reference.
Curved Handle
Upper Cord Wrap
Power Supply Cord
Telescopic Handle
Handle Lock Button
Power Switch (O/I) with LED ON/OFF Light
Steam Regulator
Water Tank Cap
Water Tank
Main Body
Lock Button (on main Body)
Mop Head
Front View
Rear View
OVERVIEW
Please make sure that the unit is unplugged from an electrical outlet and the Power Switch
(O/I) is in the “OFF” (O) position before assembling the unit or changing the accessories.
Attach the mop head to the main body as follows: Insert the swivel joint into designated
hole in the main body until it locks in place with the lock button on the main body (you will
hear a clicking sound).
Make sure that the mop head is securely locked into place before use.
Insert the stretch handle into the designated opening in the main body until it gets locked in
place with the Telescopic Handle Lock Button.
Wrap the Microfibre Cloth Pad onto the mop head, with the drawstring facing the back of
the unit. Fasten the Microfibre Cloth Pad by using the drawstring to ensure the pad is not
loose during use.
When using the steam mop on carpet surfaces: Place the mop head, with Microfibre Cloth
in place, on top of the carpet glider as illustrated. Do not attempt to use the steam mop unit
on carpet/rug surfaces without the carpet glider in place.
• Never use the carpet glider on surfaces that are prone to scratching.
• Never assemble or remove accessories while the unit is in operation.
Assembling the Handheld Steamer
Make sure the steam mop is unplugged before assembly.
Remove the Power Supply Cord from the upper cord wrap.
Press the telescopic handle lock button and remove the telescopic handle and the curved
handle from the main body.
Press and hold the lock button on the Main Body and remove the Mop Head.
To attach the Jet Nozzle: Insert the Jet Nozzle into the designated hole in the main body
unit it locks in place with the lock button on the main body (you will hear a clicking sound).
Make sure that the Jet Nozzle is securely locked in place before using.
Attach either the round nylon brush or round copper brush by screwing onto the threaded
end of the Jet Nozzle. To remove either round brush, unscrew from the Jet Nozzle.
• The round nylon brush is great for cleaning smooth hard surfaces such as toilets,
sinks and kitchen counters etc…
• The round copper brush is great for cleaning coarse or metal surfaces such as brick
floors, car wheels, metal doors, metal frames etc…
• Both brushes can also effectively clean the grease on pans, stoves and ovens in the
kitchen. They can be used with soap or detergent to clean dirty areas.
Note:
Never use the round brass brush on surfaces that are prone to scratching.
ACCESSORY ASSEMBLY
Hand-held Steaming House Tool
Remove the mop head by pressing the lock button on the main body or remove the jet
nozzle following the same procedure.
Insert the designated end of the telescopic hose into the designated hole in the main unit
until it locks in place with the lock button on the main body (you will hear a clicking sound).
Make sure the Telescopic Hose is securely locked in place before use.
Window
Loosen up the drawstring on the coral cloth and install the coral cloth onto the designated
hooks on the Window Cleaning Tool Frame. Pull up the drawstring to secure the coral cloth
in place.
Note: Do not cover the squeegee blade. Make sure to attach the coral cloth to all hooks on
the cleaning tool frame to prevent slipping or falling from the frame during use.
Cleaning Tool
Align the lock button on the telescopic hose with the designated hole on the window
cleaning tool frame and then push the telescopic hose in until it locks into place.
Garment
To use the window cleaning tool as a garment steamer, install the microfibre cloth (garment
steaming cloth) over the window cleaning/garment steamer tool.
Steaming Tool
Attach the Window Cleaning/Garment steamer tool to the telescopic hose as follows: Align
the lock button on the telescopic hose with the designed hole on the window
Cleaning/Garment steaming tool frame and then push the telescopic hose until it locks in
place.
Duster
Install the cleaning coral cloth onto the duster frame.
Attach the duster frame to the telescopic hose as follows:
Align the lock button on the telescopic hose with the designated hole on the duster frame
and then press the telescopic hose in until it locks into place.
Align the lock button on the telescopic hose.
Hand-held Steamer Use
Caution: Make sure the steam mop is unplugged.
Fill the Water Tank with water. Please refer to the “How to use the steam mop” section in this
manual. Attach either the round nylon brush or the round copper brush as explained in the
“How to assemble Hand-Held Steamer” section in this manual.
1. Select one of the following Steam Regulator positions:
1. Low
2. Medium
3. High
4. Hot Spray.
You can change the Steam Regulator position and the steam output while
operating the steam mop.
2. Once the unit has been fully assembled and filled with water, plug in the power
cord to a grounded electrical outlet. Power Switch is in the OFF (O) position, turns
the Power Switch to the ON (I) position. After approximately 30 seconds, turn on
the steam regulator and adjust the steam according to your requirement. The Mop
will start emitting steam. To stop emitting steam, turn off the steam regulator and
then turn the Power Switch to the OFF position.
Note: Be sure to turn the unit OFF after each usage and then disconnect from the
electrical outlet so the unit is in the OFF when used next time.
3. Slowly pass over surfaces to be cleaned. Apply steam liberally. Keep a towel handy
and wipe away any excess water that may accumulate.
4. When the Hand-Held Steamer stops emitting steam, simply turn OFF and unplug
the unit, refill the Water Tank and continue cleaning.
To sanitise your work surfaces, kitchen countertops, sinks, bathrooms, etc. Use the HandHeld Steamer over the same area for about 15 seconds.
Note: Do not carry out this procedure on heat and steam sensitive surfaces. The force and
heat of the steam may adversely affect certain materials. Always check the suitability of
using the steamer on a particular surface by first testing a hidden area.
Warning:
Never direct the steam towards people, animals or plants.
• Do not use the steam to clean frozen windows.
• Be careful when using the steamer on glass, as it may break.
• Do not use the steamer on leather, wax polished furniture or waxed floors, synthetic
fabrics, velvet or other delicate steam-sensitive materials.
Kogan.com assume no liability for personal injury or property damage resulting from the
misuse of the steam mop, including the failure to comply with instructions contained in this
User Guide or provided by the manufacturer or distributor of the treated surface.
the Steam Mop
Using
Please Read Before Use
• The steam mop is designed to thoroughly clean floor surfaces, such as marble,
ceramic, carpet, stone, linoleum and sealed hardwood floors and parquet. Not all
floor types are suitable for steam cleaning.
• The heat and steam action may remove the wax on surfaces treated with wax.
Does not use on unsealed flooring or let the unit stand on any wood or heatsensitive floor for an extended period. This could cause the wood grain to rise, in
addition to other types of damage.
• When using on vinyl, linoleum or any other heat sensitive floors, use extra caution.
Too much heat can melt glue within flooring. Use only on laminated the flooring
that has been laid professionally and without any gaps or cracks that would permit
the entry of moisture. Test the Steam Mop on a small isolated area of your flooring
before overall use on any floor surface.
• Always check the use and care instructions of your flooring manufacturer or
distributor before using the Steam Mop. When in doubt, please consult a flooring
specialist. Only use the carpet glider on carpeting and rugs. Use of the carpet glider
on other floor surfaces will cause streaking and possibly scratching.
Note: This product emits steam and creates moisture. Watermarks, discolouration or
damage to the floor surface can occur if the unit is left operating too long in one place.
Step 1: Filling the water tank
Caution: Make sure the steam mop is unplugged.
This steam mop uses tap water; however, if you live in a region with hard water, distilled
water should be used for better performance.
Turn the Water Tank cap counter-clockwise approximately 90° to the “OPEN” position
and remove the cap as illustrated in Fig.1 a, b and c.
Hold the Mop at a 45° angle as illustrated in Fig.1d. Add water in the tank up To the MAX
level by using the measuring cup.
Do not overfill. The maximum tank capacity is 400ml.
Replace the Water Tank cap and then turn it clockwise approximately 90° to the “CLOSED”
position until the cap is tightened securely.
Make sure the Copper Cone inside the Water Tank is always submerged in water (as shown
1. Low
2. Medium
3. High
4. Hot Spray
in Fig. 1i to right) while operating.
Note:
Never put cleaning detergents or scented products into the STEAM MOP. This will
make the operation unsafe and may damage the unit.
Step 2: Select one of the following Steam Regulator positions
• 1 (low) and 2 (medium) settings: ideal for cleaning all hard floors such as linoleum,
ceramic, marble, wood etc.
• 3 (high) ideal for cleaning carpets and rugs.
• 4 (hot spray) idea for cleaning bathrooms, kitchens, windowsills etc.
Power Switch
You ca n change the steam regulator position and change the steam output while operating
the steam mop.
Step 3: Turning the Mop on
Once the unit has been fully assembled and filled with water, plug in the Power Cord to an
electrical outlet. Make sure the Power Switch is in the OFF (O) position. Once plugged in,
turn the Power Switch to the ON (I) position.
After approximately 30 seconds, the steam regulator will turn on.
Adjust the steam according to your requirement. The Mop will start emitting steam. To stop
emitting steam turns off the steam regulator and then turns the Power Switch to the OFF
position. If the Power Switch turns to the ON position and then turn on the steam regulator
earlier than 30 seconds, water from the previous use will not be heated and will be forced
out by steam.
This may also happen you just turn off the Power Switch to the OFF (O) position and left the
steam regulator on from the previous use and the unit was disconnected by unplugging
only. Make sure you turn the unit OFF after each usage and then disconnect from the
electrical outlet, so the unit is in the OFF when used next time.
4: Cleaning Surfaces
Step
Slowly pass over the surface to be cleaned. The absorbent mop cloth picks up the dirt
loosened by the steam. Apply steam liberally. Keep a towel handy and wipe away any
excess water that may accumulate.
When the steam mop stops emitting steam, simply turn OFF and unplug the appliance,
refill the Water Tank and continue cleaning.
Warning:
Never leave the STEAM MOP unattended while it is plugged in.
Best Results
For
• Sweep/vacuum the floor before using the steam mop.
• The microfibre cloth must be clean and dry for use. To replace the cleaning cloth,
proceed as follows:
1. Let the cleaning cloth cool down.
2. Remove the cloth from the unit.
3. Replace with a new/clean microfibre cloth and then continue use.
• To sanitise an area of your floor, leave the steam mop at high steam setting over
the area for about 10 seconds, but never any longer than 15 seconds.
Note:
Never carry this procedure on heat or steam sensitive surfaces.
• Never use steam in one spot for too long. This can cause floor surface damage.
• Do not put hands or feet under the steam mop. This unit becomes very hot.
• During use, a pulsing noise may be heard indicating the mop is producing steam.
This noise is normal.
• There may be some minor “spitting” of water mixed with the steam. This is normal.
• The force and heat of the steam may adversely affect certain materials. Always
check the suitability or using the steam mop on a surface by carrying out a
preliminary test on a hidden area.
Kogan.com assumes no liability for personal injury or property damage resulting from the
misuse of the steam mop, including the failure to comply with instructions contained in
this User Guide or provided by the manufacturer or distributor of the treated surface.
Handheld Steamer
The Hand-Held Steamer is an ideal portable cleaner for use on work surfaces, countertops,
sinks, windows, mirrors, tiles and spot cleaning on floors, carpets and rugs. Use it with the
Jet Nozzle, Brass brush or Nylon brush attachments to spray away dirt, grease, mould and
more.
Window
Make sure the steam mop is unplugged.
Cleaning Tool
1. Fill the Water Tank with water. Please refer to the “Using the steam mop” section in
this manual
2. Install the Coral Cloth onto the Window Cleaning Tool and attach the Window
Cleaning Tool to the Telescopic Hose as described in the “Accessory Assembly”
section in this manual.
3. Follow Steps 2-3 described in the “How to use the Hand-held Steamer” section in
this manual.
4. Hold the Hand-held Steamer in one hand and grasp the handle grip on the
telescopic hose with the other hand as illustrated.
5. Slowly pass over glass (or other similar) surface to be cleaned. Apply steam liberally.
The absorbent Coral Cloth picks up the dirt loosened by the steam and the
squeegee blade removes any remaining trails of water. Keep a towel handy and
wipe away any excess water that may accumulate.
Caution: Pulling on the telescopic hose with excessive force will damage it, possibly
can get hot.
resulting in a steam leak.
Warning - Danger of Scalding
Do not touch the window cleaning tool/coral cloth during use, as these
components can get extremely hot.
Keep the telescopic hose away from your body and avoid touching the hose as it
6. When the hand-held steamer stops emitting steam, simply turn off and unplug the
unit. Refill the water tank and then continue cleaning.
7. Once you finish cleaning, allow the coral cloth to cool down and then carefully
remove it from the Window Cleaning Tool, as the cleaning cloth may still be hot.
• Do not use the steam to clean frozen glass.
• Be careful when using the steamer on glass, as it may break.
Garment Steamer
Make sure the steam mop is unplugged.
1. Fill the Water Tank with water. Please refer to the “How to use the steam mop”
section in this manual.
2. Install the Garment Steamer Cloth onto the Window Cleaning/Garment Steaming
Tool and attach the Window Cleaning/Garment Steaming Tool to the Telescopic
Hose as described in the “How to Assemble the Optional Accessories” section in
this manual.
3. Select one of the following Steam Regulator Positions: 1-Low or 2-Medium. Do not
use 3-High and 4-Hot Spray steam settings when using the Garment Steamer.
When using the Garment Steamer. You can change the Steam Regulator position
and steam output while operating the steam mop.
4. Follow Step 3 described in the “How to Use the Hand-Held Steamer” section in this
manual.
5. To steam a garment, place item of clothing on the hanger and steam the garment
directly.
6. Hold the Hand-Held Steamer in one hand and grasp the handle grip on the
Telescopic Hose with the other hand as illustrated. Slowly slide the Garment
Steamer Head vertically, from the top to the bottom of the garment. You may also
reverse this motion and steam from the bottom to the top. Curtains and draperies
can be steamed while they are hanging.
Notice: Please refer to the label on an item of clothing to check if the garment can be
steamed. Some fabrics like leather, suede and velvet may not be suitable for steaming. If
you are not sure then steam a small part of the inside of the garment to test that it does not
damage the fabric before steaming the entire garment or fabric.
Caution: Pulling on the Telescopic Hose with excessive force will damage the hose, possibly
resulting in a steam leak.
The danger of Scalding: Do not touch the Garment Steamer Tool/Cloth during use, as
these components can get extremely hot. Keep the Telescopic Hose away from your body
and avoid touching the hose as it can get hot.
7. When the Hand-Held Steamer stops emitting steam, simply turn off and unplug
the unit, refill the Water Tank and continue cleaning.
8. Once you finish cleaning allow the Garment Steamer Cloth to cool down and
carefully remove it from the Window Cleaning Tool, as the Garment Steamer Cloth
could still be hot.
Duster
Make sure that the steam mop is unplugged.
1. Fill the Water Tank with water. Please refer to the “HOW TO USE THE steam mop”
section in the manual.
2. Install the Coral Cloth onto the Duster frame and attached the Duster to the
extension Hose as described in the “How to Assemble the Optional Accessories”
section in this manual.
3. Select one of the following Steam Regulator position: 1-Low, 2-Medium or 3-High.
Do not use 4-Hot Spray steam setting when using the Duster. You can change the
Steam Regulator position and change the steam output while operating the steam
mop.
4. Follow Step 3, described in the “How to Use the Hand-Held Steamer” section in
this manual.
5. Hold the Hand-Held Steamer in one hand and grasp the handle grip on the
Telescopic Hose with the other hand as illustrated above.
6. Slowly pass over surface to be cleaned. The absorbent Coral Cloth picks up the dirt
loosened by the steam. Keep a towel handy and wipe away any excess water that
may accumulate.
resulting in a steam leak.
Warning:
Pulling on the telescopic hose with excessive force will damage it, possibly
Warning: Danger of Scalding
Do not touch the duster/coral cloth during use, as these components can get
extremely hot. Keep the telescopic hose away from your body as it can get very
7. When the Hand-Held Steamer stops emitting steam, simply turn off and unplug
the unit, refill the Water Tank and continue cleaning.
8. Once you finish cleaning allow the Duster Coral Cloth to cool down and carefully
remove it from the Duster frame, as the Coral Cloth could still be hot.
Garment
Make sure the steam mop is unplugged.
Steaming Cloth
1. Fill the Water Tank with water. Please refer to the “How to use the steam mop”
section in the manual.
2. Install the Garment Steaming Cloth onto the Window Clearing/Garment
Steaming Tool and attach the Window Clearing/Garment Steaming Tool to the
Telescopic Hose as described in the “How to Assemble the Optional Accessories”
section in this manual.
3. Select one of the following Steam Regulator position: 1-Low or 2- Medium. Do not
use 3-High and 4 -Hot Spray steam settings when using the Garment Steamer.
You can change the Steam Regulator position and the steam output while
operating the steam mop.
4. Follow Step 3, as described in the “How to Assemble the Optional Accessories”
section in this manual.
5. Hold the hand-held Steamer in one hand and grasp the handle grip on the
Telescopic Hose with the other hand as illustrated above.
6. Slowly pass over surface to be cleaned. The absorbent Lint Cloth picks up the
dirt/hair loosened by the steam. Do not use on animals.
Caution: Pulling on the Telescopic Hose with excessive force will damage it, possibly
resulting in a steam leak.
Warning: Danger of Scalding
Do not touch the Window Cleaning/Garment Steamer Tool or the Garment Steaming
Cloth during usage, as these components can get extremely hot. Keep the Telescopic
Hose away from your body and avoid touching the hose, as it can get hot.
7. When the Hand-Held Steamer stops emitting steam, simply turn off and unplug
the unit, refill the Water Tank and continue cleaning.
8. Once you finish cleaning, allow the Lint Cloth to cool and carefully remove it from
the Window Cleaning.
Coral Cloth for Mop Head
Attach the triangle-shaped Coral Cloth to the Mop Head following the same instructions as
provided for the Microfibre Cloth with Hook and Loop tape in the “How to assemble the
steam mop” section in this manual.
The Coral Cloth is soft and durable with hundreds of super absorbing fringes, ideal for your
sealed headword, ceramic and other types of flooring.
Kogan.com assumes no liability for personal injury or property damage resulting from the
misuse of the steam mop, including the failure to comply with the instructions contained
in this User Guide or provided by the manufacturer or distributor of the treated surface.
After Use
1. Unplug Power Cord from the outlet.
2. Allow Mop Pad/Cloths to cool down and carefully remove cleaning cloth from mop
Head, as cleaning cloth could still be hot.
3. Any water remaining in the Water Tank should be emptied before appliance
storage. Always empty the Water Tank at the end after each use.
4. Let any water (that may remain as a product of condensation) drain from the
steam opening before storing the appliance.
5. Wrap Power Cord around Upper and Lower Cord Wrap.
6. Wipe all surfaces of the steam mop with a soft cloth.
7. Please store the unit in a cool and dry place when not in use. Do not leave it
exposed to sunlight or rain.
8. Upright storage of the steam mop with a wet Mop Pad/Cloth may result in the
formation of white marks on your floor. To remove the white marks, clean the
specific area with vinegar. Make sure to remove the Mop Pad/Cloth before storage.
Warning:
Be sure that the unit is disconnected from the power outlet before cleaning.
Drain the remaining water in the tank and clean the tank after every use. Please use
detergent to clean the accessories (Jet Nozzle and Rough Brush) when they are dirty, then
wash with clean water and air dry.
How to decalcify the Water Tank interior
• To clean calcium deposits that build up inside the Water Tank, add one or two
tablespoons of white vinegar to a full Water Tank, close the Water Tank cap and
shake the contents. Do not turn the Steamer On.
• Let the unit sit for a few hours. Then, empty the Water Tank and refill with clean
water and empty until it rinses clear.
Removing Limescale from the Steam Mop
If your steam mop begins to produce steam more slowly than usual or stops producing
steam, you may need to remove limescale.
Limescale can develop over time on the metal parts and greatly affect mop performance. It
is necessary to remove the scale regularly every 25-50 times you use a full tank of water or at
least once a month, especially in areas with hard water. The frequency of limescale removal
depends upon the hardness of your tap water and how often you use the steam mop. The
steam mop uses tap water. However, in areas with hard water, distilled water should be used
for better performance.
To remove limescale from the steam mop, please follow these procedures:
Warning:
Do not immerse the steam mop in water.
Using a scraper
1. Make sure that the steam mop is disconnected from the power supply before
maintenance.
2. Use the cleaning pin to remove scale deposits from the small hole of the steam
outlet in the Main Body by swirling and pushing the pin-up and down you will clean
the steam outlet. Always ensure that all scale debris has been removed from the
steam outlet before reassembling. Continue swirling Cleaning Pin until no further
debris is evident.
Using a cleaning solution
1. Prepare a solution of 1/3 white vinegar and 2/3 tap water and add to the water
tank.
2. Secure and position the unit to ensure steam released is aimed away from the floor
or surrounding objects and surfaces. Plug the unit in, turn the unit ON by pressing
the Power Switch (O/I) and allow the unit to produce steam until the vinegar/water
solution is used up.
3. Repeat the above procedures as many times as necessary until a normal steam
flow rate is achieved.
4. Fill the Water Tank with fresh water and rinse out.
5. Fill the Water Tank with fresh water, attach to the unit and release steam through
the system until the Water Tank is empty.
Warning:
Do not leave the steamer unattended during the limescale removal process and/or
while in use.
Note:
Perform a test cleaning on a suitable isolated area after each limescale removal to
ensure that there is no debris in the system.
Cleaning Blocked Steamer Accessories
• Due to the high mineral content of water in some areas, you may notice that less
steam comes out from the Hand-Held Steamer accessories. This may be caused
by calcium build-up inside the tip of the nozzle.
• To clean calcium build-up, it recommends using a spray lubricant. Spray a small
burst or two of the lubricant inside the tip of the Jet Nozzle. After spraying lubricant
inside the component, fill the steamer with water according to the directions and
run a continuous jet of steam through the affected accessory to several minutes to
remove the deposit. Once the steam pathway is clean, aim the steamer at a
neutral surface or a cleaning cloth to make sure no debris is emitted.
• It recommends performing this procedure in a protected and well-ventilated area.
• The microfibre cloth can be machine washed in warm to hot water. Do not bleach.
Do not use fabric softener.
Problem
Possible Cause
Solution
Make sure the unit is plugged
switch is on.
• Fill water tank.
procedure in this manual.
• Turn unit OFF, allow it to
check and clean them.
Remove the wet cloth and
reattach.
Warning:
To reduce the risk of fire, electric shock or injury, unplug the appliance from the power
source before servicing.
The unit does not
power on.
Reduced steam or no
steam.
Steam escapes from
connections.
Cleaning cloth gets
wet.
Unit is not plugged in.
• Water tank empty.
• Blocked steam nozzle.
• Limescale.
• Attachment is not
• There are some
Exposure to moisture.
connected properly.
debris/obstructions in
the connection points.
into a proper outlet and the
• Remove the mop head
and clean the nozzle.
• Follow the cleaning
cool down, then
disconnect accessories
and reattach them
properly.
• Remove accessories and
replace with a new cleaning
cloth or wring it out and
Glider
Microfibre Cloth
Measuring Cup
Cleaning Pin
Round Brush
(Nylon)
Jet Nozzle Round Brush (Brass)
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
Loading...