HEALTH IMAGING
{OperatorsManual}{Product io n}{HealthImaging}
OPERATOR MANUAL
for the
Publication No. 7C8770
19JAN99
Supersedes 7C8770
03DEC98
Kodak X-Omat
Kodak X-Omat
2000 PROCESSOR
2000A PROCESSOR
© Eastman Kodak Company, 1999
PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the
subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice, and
makes no warranty, express or implied, with respect to this information. Kodak shall not be liable
for any loss or damage, including consequential or special damages, resulting from any use of
this information, even if loss or damage is caused by Kodak’s negligence or other fault.
Warning
To avoid hazardous conditions, keep floors and floor coverings around your
associated drains clean and dry at all times. Any accumulation of fluids from mixing tanks, drain lines, etc., should
be cleaned up immediately. In the event of an accumulation of liquid due to backup, overflow, orother malfunctions
of the drain associated with your
the drain. Kodak accepts no responsibility or liability whatsoever for the serviceability of any drain connected to or
associated with a
Kodak X-Omat
X-Omat
Processor. Such drains are the sole responsibility of the customer.
Processor, call a plumber or other contractor to correct any problem with
Kodak X-Omat
Processor and
Table of Contents
Description Page
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Processing Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Feeding Sheet Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Feeding Roll Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Processing Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparing the Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Draining the Tanks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Filling the Tanks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Replenishment Flow Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Correcting Difficulties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleanup and Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Daily Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Every Two Weeks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Special Maintenance for Low or High Volume Usage . . . . . . . . . . . . . . . . . . . . 18
New Equipment Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2 19JAN99 – 7C8770
Overview
Section 1: Overview
The
Kodak X-Omat
processed in
The self-threading roller transport system has:
• a film-length detection system
• a replenishment system
• a developer solution filter
• a recirculation system for the developer and fixer solutions
• an automatic standby feature
The Processor can operate at 2 different transport speed cycles:
• Standard Cycle has a transport speed of 76.2 2.0 cm (30 0.6 in.) per minute or 157 5 seconds drop time
(dry to dry) for a 43 cm (17 in.) sheet of film. The developer temperature is 33.3 0.3°C (92.0 0.5°F).
• Rapid Cycle has a transport speed of 101.6 1.5 cm (40.1 0.8 in.) per minute or 118 4 seconds drop time
(dry to dry) for a 43 cm (17 in.) sheet of film. The developer temperature is 34.4 0.3°C (94.0 0.5°F).
• Both Cycles use standard
Note
The transport speed can only be changed by qualified personnel.
A film feed signal sounds 3secondsafter the film being processed hasclearedtheRollers of the Detector Crossover
Assembly. This indicates that the Processor is ready to accept another piece of film.
2000 and 2000A Processors are designed toprocess medical x-ray sheetor roll film thatcan be
Kodak RP X-Omat
Developer and Replenisher and in
Kodak RP X-Omat
Fixer and Replenisher.
Kodak RP X-Omat
Fixer and Replenisher.
7C8770 – 19JAN99 3
OPERATORS MANUAL
Section 2: Processing Film
Start-Up
Figure 1 Main Power Switch
TOP COVER
RUN/STANDBY
SWITCH
Warning
Keep fingers, clothing, cleaning materials, etc., away
from the moving parts of the Processor.
[1] Turn on the water supply and the Main Power
Switch.
[2] Remove the Top Cover.
RUN/STANDBY
SWITCH
MAIN POWER SWITCH
Figure 2 Water Inlet Tube of the Wash Tank
2 EVAPORATION
COVERS
TOP
COVER
H172_1000ACA
H172_1000AC
WATER
INLET TUBE
TEMPERATURE
READY LIGHT
H172_0501ACC
H172_0501AC
DRYER
TEMPERATURE
CONTROL
KNOB
[3] Check the following are seated correctly.
(See Figure 3.)
• Developer Rack
• Fixer Rack
• Wash Rack
• Fixer/Wash Crossover Assembly
• Developer/Fixer Crossover Assembly
• Detector Crossover Assembly
• Dryer Assembly
[4] Check:
• developer,fixer,andwashsolutionsare at the
overflow level of the Weirs
• water is flowing from the Water Inlet Tube of
the Wash Tank
• Evaporation Covers are installed
4 19JAN99 – 7C8770
Processing Film
Figure 3 Racks and Crossovers
DEVELOPER/FIXER
CROSSOVER ASSEMBLY
FIXER/WASH
CROSSOVER
ASSEMBLY
WASH
RACK
DRYER
ASSEMBLY
[5] Install the Top Cover on the Processor.
[6] Allow the developer solution to reach the correct
temperature.
Recommended developer temperatures:
Cycle type Developer Temperature
Standard 33.3 0.3°C (92.0 0.5°F)
Rapid 34.4 0.3°C (94.0 0.5°F)
Note
The Temperature Ready Light flashes or turns off when
the developer solution is at the correct temperature.
[7] Press the Run/Standby Switch.
[8] When the Temperature Ready Light flashes,feed
a sheet of
into the Processor.
[9] Adjust the Dryer Temperature Control Knob tothe
lowest setting to dry the film.
Kodak
Roller Transport Cleanup Film
FIXER
RACK
DEVELOPER
RACK
FEED SHELF
DETECTOR
CROSSOVER
ASSEMBLY
H172_1001CCA
H172_1001CC
7C8770 – 19JAN99 5
OPERATORS MANUAL
Feeding Sheet Film
Figure 4 Film Sizes and Direction of Film Feed
1 each
35 x 43 cm
or
14 x 17 in.
1 each
24 x 30 cm
or
10 x 12 in.
1 each
1 each
35 x 35 cm
or
14 x 14 in.
1 each
24 x 24 cm
1 each
[1] Press the Run/Standby Switch.
Note
• The Motors will begin to operate.
• After film removal, the Processor will automatically
return to the standby mode.
• The Temperature Ready Light flashes or turns off
when the developer solution is at the correct
temperature for processing film.
[2] Feed a sheet of film into the Processor.
Note
• Insert single-emulsion films with the emulsion side
up.
• A film feed signal will sound 3 seconds after the
trailing edge of a sheet offilm has leftthe Rollers of
the Detector Crossover Assembly.
2 each
10 x 10 cm
18 x 24 cm
or
4 x 4 in.
18 x 43 cm
1 each
11 x 14 in.
H172_1002CC
Feeding Roll Film
Caution
• Use only
bases are soluble in the processing solutions.
• The adhesive side of the tape must not be exposed.
[1] Use a sheet of film as a leader.
[2] Use 2 cm (1 inch) wide
film.
3M SCOTCH
Brand Polyester Film Tape No.850. Othertypes oftape are unacceptable,because their
3M SCOTCH
Brand Polyester Film TapeNo. 850to connect the sheetof film to the roll
6 19JAN99 – 7C8770
Shutdown
Processing Film
Figure 5 Processor in Shutdown Mode
TOP COVER
MAIN
POWER
SWITCH
H172_0502ACA
H172_0502AC
[1] Turn off the Main Power Switch and the water
supply.
[2] Disconnect the main power.
[3] Remove the Top Cover and Evaporation Covers.
[4] Do the “Daily procedure” on Page 15.
Important
Keep the Top Cover open overnight for venting
purposes.
[5] Install the Top Cover with a 5 cm (2 in.) opening.
7C8770 – 19JAN99 7
OPERATORS MANUAL
Section 3: Processing Solutions
Preparing the Solutions
Figure 6 Processing Tanks with the Splash Guard
and the Drip Tray
DRIP TRAY
Caution
Draining the Tanks
SPLASH GUARD
H172_1003ACA
H172_1003AC
• Avoid contamination of the processing solutions.
• To avoid spilling solutions from one Tank into the
next one, use the Splash Guard between the
developer and fixer Tanks.
• Slowly install or remove the Racks.
• Use the Drip Tray when moving Racks to or from
the Processor.
• Do not mix more than a 2-week supply of
chemicals.
[1] Mix the volume of processing solution required in
the correct replenisher Tank. Use the instructions
packed with the chemicals to mix the solution.
Note
Refer to ServiceBulletin 30, Part No. 632661,for more
information.
[2] Remove the Crossover Assembly and the Rack
from the Tank that is to be filled.
Warning
• All drain materialmust be made of chemicallyresistant, non-corrosive material. Use PVCor the equivalent. The
Drain must have a minimum diameter of 7.6 cm (3 in.) and no obstructions. See the Site Specifications,
Publication No. 7C8769.
• Relatively small amounts of fixer can seriously contaminate the developer. If solutions are changed in both
Tanks, fill the fixer Tank first so that any solution spilling into the developer Tank can be thoroughly cleaned.
• Drain only one Tank at a time.
8 19JAN99 – 7C8770
Figure 7 Draining the Tanks
Processing Solutions
WEIRS
WATER INLET
3 DRAINS
WASH
FIXER
DEVELOPER
DEVELOPER
FIXER
WASH
H172_0503DCA
H172_0503DC
[1] If the Processor has a SilverRecovery Unitconnected, disconnect the Fixer Drain Tube at the input side of the
Silver Recovery Unit. See Figure 13 on Page 17.
[2] Lift the blue Weir from the fixer Tank.
[3] Drain the fixer solution. Check the local codes for the correct disposal procedures.
Important
Do not interchange the Weirs.
[4] When the fixer Tank is drained, install the blue Weir.
[5] Drain the developer Tank in the same way.
Weir Tank
red developer
blue fixer
beige wash
7C8770 – 19JAN99 9
OPERATORS MANUAL
Filling the Tanks
Figure 8
WEIRS
DEVELOPER
TANK
H172_1004ACA
H172_1004AC
WASH
TANK
FIXER
TANK
[5] To fill the developer Tank:
(a) Fill the developer Tank half full of developer replenisher from the replenisher tank.
(b) Add 190 mL (6.5 fl oz) of
Kodak RP X-Omat
(c) Fill the developer Tank to the higher Fill Line on the red Weir with developer replenisher.
[6] Remove the Splash Guard and rinse thoroughly with water.
FILL
LINES
• Mix the developer solution first, then the fixer.
• Wash the mixing equipment thoroughly between
solutions to avoid contamination of the solutions.
• Rinse the mixing and filling equipment before each
use.
• Fill the fixer Tank first.
[1] Install the Splash Guard between the developer
Tank and the fixer Tank. See Figure 6 on Page 8.
[2] To fill thefixer Tank,add fixerreplenisher untilthe
solution is at the higher Fill Line on the blue Weir.
[3] Remove and rinse the Splash Guard.
[4] Install the Splash Guard over the Fixer Tank.
Developer Starter.
Caution
Caution
When installing the Racks, use the Splash Guard. Lower the Racks slowly.
[7] Install the Racks in the correct Tanks. Seat them firmly.
Note
The Washer onthe top of the drive side of thedeveloper Rack hasa “D” on it. The fixer Rack hasan “F”. The Racks
may also have red, blue, and white wire ties for easy identification:
• red for the developer Rack
• blue for the fixer Rack
• white for the wash Rack
[8] Install the Crossover Assemblies, the Dryer Assembly, and the Evaporation Covers.
[9] Allow the developer to reach the operating temperature before processing any film.
10 19JAN99 – 7C8770
Section 4: Replenishment Flow Rates
Figure 9
DEVELOPER TUBING
METAL LATCH
H172_1005ACA
H172_1005AC
QUICK
DISCONNECT
GRADUATED
CYLINDER
FIXER TUBING
Wear protective eyewear. The replenishment solutions
are pumped quickly and might splash.
The Developer Tubing may have a red Wire Tie on it for
easy identification.
Replenishment Flow Rates
Warning
[1] Remove the Top Cover.
[2] Lift the Upper Roller of the Detector Crossover
Assembly.
[3] Check that the replenisher solutions flow freely
through the Tubinglocated alongthe driveside of
the Racks.
[4] Disconnect the Developer Tubing by pressing the
Metal Latch.
Note
[5] Pull the Developer Tubing slightly and rotate it
over the edge of the frame and into a Graduated
Cylinder.
[6] Lift the Upper Roller of the Detector Crossover
Assembly for the correct time:
Standard Cycle: 34 seconds
Rapid Cycle: 25 seconds
[7] When the Replenishment Pump stops, check that the amount of solution in the Graduated Cylinder is correct
for the film size and use condition. See the table on Page 12. If the amount is not correct, contact qualified
service personnel.
[8] Connect the DeveloperTubing again by pushing it into theMetal Latch untilthe Developer Tubing locks in place.
[9] Check the fixer replenishment flow rate by doing Steps 3 - 8 with the Fixer Tubing.
[10] Install the Top Cover.
Figure 10 Detector Crossover Assembly
UPPER ROLLER
DETECTOR CROSSOVER
ASSEMBLY
2 DETECTOR
SWITCHES
H172_1006BCA
H172_1006BC
7C8770 – 19JAN99 11
OPERATORS MANUAL
Table 1 Setting Replenishment Flow Rates
Replenishment Flow Rate,
mL per 35 x 43 cm
34 seconds for Standard Cycle
25 seconds for Rapid Cycle
Developer Fixer
Film Size Processed Use Condition
Average Amount of Film
per 8 Hours of Processor
Operation
Only roll films 35 cm wide High 105 Linear feet or more 50 70
Medium 35 to 105 linear feet 65 85
Low 35 linear feet or less* 80 100
Only 35 x 35 cm film High 90 sheets or more 50 70
Medium 30 to 90 sheets 65 85
Low 30 sheets or less* 80 100
Average size intermix film High 115 sheets or more 50 70
Medium 40 to 115 sheets 65 85
Low 40 sheets or less* 80 100
Only 35 x 43 cm film High 75 sheets or more 60 85
Medium 25 to 75 sheets 80 100
Low 25 sheets or less* 100 120
* If sensitometry does not stay within control limits, flooded replenishment may be needed. Contact your Kodak
Representative to order and install the Flooded Replenishment Kit, Part No. 419779.
Note
Refer to Service Bulletin30, PartNo. 632661, for additionalinformation andthe latest processing recommendations.
12 19JAN99 – 7C8770
Correcting Difficulties
Section 5: Correcting Difficulties
1. Transport Failure
2. Surface Artifacts
3. Abnormal Film Densities
4. Wet Films
5. Low Solution Levels
6. Overlapping of Films
123456
• • Film Feeding Error
Feed only single thicknesses of film. Feed the next film only after the
film feed signal sounds If there is no film feed signal, refer the difficulty
to qualified service personnel.
• • • • Feed only compatible films.
• • Check that all Racks and Crossovers are seated correctly.
• • Check that the surfaces of all the Rollers are clean and smooth, especially in
the Developer Turnaround Assembly.
• • Check that the Dryer Air Tubes are in the correct positions.
• • Remove any dirt from the Dryer Rollers and Air Tubes, especially the slots.
Use a bottle brush and rinse with water.
• • • • Check that the replenishment settings are correct.
• Adjust the Dryer temperature control setting to the lowest possible
temperature that still allows good drying.
• Clean the Feed Shelf and Detector Rollers.
• • • Clean any biological growth in the Wash Tank with a mild solution of chlorine
bleach. Use 60 mL (2 fl oz) of bleach per 3.8 L (1 gallon) of water. Wipe the
Tanks with a soft sponge.
• • Check that the Weirs are seated correctly. Check that the Tanks are full.
• • • • • Change any chemicals that were not mixed correctly, are exhausted, or are
contaminated. Check that the replenishment flow rates are correctly set. Fill
the Replenishment Tanks if necessary.
• • • Check that all Rollers are in place and positioned and rotating correctly.
• • • Check that all Roller Gears, Sprockets, and Idlers are engaged.
• • • Replace any Roller that has a broken or worn Gudgeons.
• • • Replace any Bearings that do not allow the Turnaround Rollers to rotate
correctly.
• • Check the tension on the Rack Chain. Check that the Rollers do not hesitate
and that the Chain moves smoothly.
• With the Processor on, check for movement on the surface of the solutions.
Movement indicates recirculation.
• • If the incoming wash water is dirty, clean the Rack and Tank thoroughly.
Change the incoming Water Filter. Make sure to use the correct Water Filter.
• Check that the Dryer Air Exhaust is free from any obstruction.
• • Check that the Turnaround Assembly isadjusted correctly. Makesure that the
Turnaround Assemblies are square with the Racks.
• • Check the incoming water temperature. Temperature must be between 4.4 C
(40 F) and 29.4 C (85 F).
7C8770 – 19JAN99 13
OPERATORS MANUAL
1. Transport Failure
2. Surface Artifacts
3. Abnormal Film Densities
4. Wet Films
5. Low Solution Levels
6. Overlapping of Films
123456
• Check that the correct Bulb and Safelight Filter are in the Safelight and at the
correct distance from the Feed Shelf and work surface.
• • Check that the Top Cover and Panels are tight on the Processor. Check that
there are no leaks in the Lighttight Gasket.
• 10 x 10 cm films - feed films diagonally if they fail to transport reliably.
• Check the time delay. For all transport speeds, thebuzzer should sound once
the trailing edge of the film has advanced 75 mm (3 in.) into the Processor.
• • • • Check that the tank solution levels are at the overflow Weirs.
• Check for solution in the Replenishment Tanks. Fill if necessary.
NOTE: Mix developer replenisher in quantities not to exceed a 2-week
supply.
• With a thermometer of known accuracy, check that the temperature of the
developer is correct. If necessary, have qualified service personnel make
adjustments.
NOTE: Check the incoming water temperature. It must be a minimum of 4 C
(7 F) lower than the desired developer temperature.
14 19JAN99 – 7C8770
Section 6: Cleanup and Periodic Maintenance
Daily Procedure
The best time to do daily cleanup is at shutdown.
Figure 11 Daily Cleaning of the Racks and
Crossover Assemblies
DRYER
ASSEMBLY
GUIDE
SHOE
Warning
• Dangerous Voltage. Disconnect the main power
before doing any of the following cleanup
procedures.
• Wear rubber gloves, safety glasses and protective
clothing when doing any maintenance procedure.
• Report any change in the operating condition of the
Processor to Service Personnel.
[1] Turn off the Main Power Switch.
[2] Disconnect the main power.
[3] Turn off the water supply.
[4] Remove the Top Cover.
Cleanup and Periodic Maintenance
Caution
• When removing the Crossover Assemblies, be
careful to maintain squareness, and do not disturb
the Guide Shoes.
• Use a damp cloth or a synthetic sponge and warm
water. Do not use any abrasive material on the
Racks, Crossover Assemblies, or Squeegee
Rollers.
[5] Remove the Evaporation Covers and the
CROSSOVER
ASSEMBLIES
DETECTOR
CROSSOVER
ASSEMBLY
FEED
SHELF
H172_1001CCB
H172_1001CC
[8] Wipe off all chemical deposits above the solution level in the processing section.
[9] Clean off debris or buildup from the dryer area with a warm, damp sponge or cloth.
[10] Install the Crossover Assemblies and the Evaporation Covers.
Crossover Assemblies.
(a) Rinse the Evaporation Covers.
(b) Rinse the developer/fixer and fixer/wash
Crossover Assemblies in warm water.
[6] Rotate and clean the Rollers with a soft brush and
warm water.
[7] Dry the Rollers witha cloth or syntheticsponge or
allow to air dry.
Important
Keep the Top Cover open overnight for venting purposes.
[11] Install the Top Cover leaving a 5 cm (2 in.) gap.
7C8770 – 19JAN99 15
OPERATORS MANUAL
Every Two Weeks
Figure 12 Biweekly Cleaning of the Racks and
Crossover Assemblies
CROSSOVER
ASSEMBLIES
DETECTOR
CROSSOVER
ASSEMBLY
DRYER
ASSEMBLY
FEED
SHELF
GUIDE
SHOE
H172_1001CCB
H172_1001CC
Warning
Dangerous Voltage. Disconnect the main powerbefore
doing any of the following cleanup procedures.
[1] Turn off the Main Power Switch.
[2] Disconnect the main power.
[3] Turn off the water supply.
[4] Remove the Top Cover.
Caution
• When removing the Crossover Assemblies, be
careful to maintain squareness, and do not disturb
the Guide Shoes.
• Use a synthetic sponge and warm water. Do not
use any abrasive material on the Racks,
Crossover Assemblies, or Squeegee Rollers.
• Do not rinse the Detector Crossover Assembly or
the Dryer Assembly.
[5] Remove the Evaporation Covers and the
Crossover Assemblies.
(a) Rinse the Evaporation Covers.
(b) Rinse the developer/fixer and fixer/wash
Crossover Assemblies in warm water.
[6] Rotate and clean the Rollers with a soft brush and
warm water.
[7] Dry the Rollers with a damp cloth or synthetic
sponge.
[8] Wipe off all chemical deposits above the solution
level in the processing section.
[9] Remove the Dryer Assembly.
[10] Cleanoff debris or buildupfrom thedryerarea and
Dryer Assembly with a warm, damp sponge or
cloth.
16 19JAN99 – 7C8770
Figure 13 Silver Recovery Unit
SILVER RECOVERY UNIT
BYPASS
H172_1007ACA
H172_1007AC
Cleanup and Periodic Maintenance
Caution
• Fixer will contaminate the developer. When
removing the Rack Assemblies, use the Splash
Guard between the developer and fixer Tanks.
• Use the Drip Tray when removing or installing the
Racks. See Figure 6 on Page 8.
• Do not rinse the Detector Crossover Assembly or
the Dryer Assembly.
[11] Remove the Racks.
[12] Rinse the Racks and wipe them with a cloth.
[13] Check:
(a) Chains move freely and are adjusted
correctly
(b) Rollers rotate correctly
(c) Space between the Turnaround SidePlates
and the Rack Side Plates is equal and that
the Side Plates are parallel on both ends
Figure 14 Rack and Turnaround Assembly
CHAIN
ROLLER
2 RACK
SIDE PATES
STUD
H172_1008ACB
H172_1008AC
2 TURNAROUND
SIDE PLATES
[14] Checkthe operationof the Silver Recovery Unit, if
installed.
[15] Check that no solution is flowing through the
Bypass.
Note
If solution is present inthe Bypass, theSilver Recovery
Unit is not operating.
[16] Use
[17] If the test shows more than 1 gram/liter of silver,
Kodak
SilverEstimating Test Papers to check
the silver content of the solution flowing into the
drain.
install a newcartridge inthe SilverRecovery Unit.
7C8770 – 19JAN99 17
OPERATORS MANUAL
Figure 15 Cleaning the Replenishment Strainer Assemblies
STRAINER ASSEMBLY
SCREEN
[18] Clean the Replenishment Strainers when mixing new chemicals.
(a) Place Pinch Clamps on The tubing to stop the replenishment flow.
(b) Disassemble the Strainer Assemblies.
(c) Use a brush and warm water to clean the Strainer Assemblies and to remove dirt and chemical deposits
from the Screens.
H172_1009BCA
H172_1009BC
Special Maintenance for Low or High Volume Usage
If the processor handles a low volume, less than 25 sheets of film per day, do this procedure every 2 weeks.
If the processor handles a high volume, more than 25 sheets of film per day, do this procedure monthly.
[1] Use the Procedure on Page 8 to drain the Tanks.
[2] Flush the developer and fixer Tanks with clean water.
[3] Install the Weirs, red for developer and blue for fixer.
[4] To fill the fixer Tank, add fixer replenisher until the solution is at the higher Fill Line on the blue Weir.
[5] To fill the processor developer Tank:
(a) Add 190 mL (6.5 fl oz) of
(b) Fill the developer Tank to the higher Fill Line on the red Weir with developer-replenisher solution.
Kodak RP X-Omat
Developer Starter.
18 19JAN99 – 7C8770
Cleanup and Periodic Maintenance
H172_1003AC
H172_1003ACA
SPLASH GUARD
DRIP TRAY
Figure 16 Splash Guard and Drip Tray
Caution
When installing the Racks, use the Splash Guard. Lower the Racks slowly.
[6] Install the Racks, the Crossover Assemblies, and the Dryer Assembly. Check that each Assembly seats firmly.
[7] Turn on the main power, the water, and the Processor.
[8] Check the solutions. If the surfaces of the solutions are moving, the Recirculation Pumps are operating.
[9] When the Temperature Ready Light flashes, use a thermometer of known accuracy and check the solution
temperature in the developer Tank.The correct temperature is:
Standard Cycle 33.3 0.3°C (92.0 0.5°F)
Rapid Cycle 34.4 0.3°C (94.0 0.5°F)
7C8770 – 19JAN99 19
New Equipment Warranty
Section 7: New Equipment W arranty
Warranty Coverage
Kodak warrants the
installation, when installed within one year from the date of shipment.
If the equipment does not function properly during the warranty period, the dealer that sold the equipment will provide
or arrange forrepair of the equipment during the dealer's normalworking hours. Suchrepair service will include any
necessary adjustments and/or replacement of parts necessary to maintain your equipment in good working order.
How to Obtain Service
Should equipment require service, refer to the sales contract for details on whom to call for service, or contact the
dealer that sold you the equipment.
Limitations
• Warranty service is limited to the contiguous United States, the island of Oahu in Hawaii, and certain areas of
Alaska.
• This warranty does not cover: circumstances beyond Kodak's control; misuse; abuse; any attachments,
accessories, or alterations not marketed by Kodak (including service or parts to correctproblems resulting from
the use of such attachments, accessories or alterations); failure to follow Kodak's operating instructions; or
supply items.
• Kodak makes no other warranties, express, implied, or of merchantability for this equipment.
• Repair without charge is Kodak's and the dealer's only obligation under this warranty.
– Kodak will not be responsible for any consequential or incidental damages resulting from the sale,
use, or improper functioning of this equipment even if loss or damage is caused by the negligence
or other fault of Kodak.
– Such damages for which Kodak will not be responsible, include, but are not limited to, loss of revenue or
profit, downtime costs, loss of use of the equipment, cost of any substitute equipment, facilities or services
or claims of your customers for such damages.
• This limitation of liability will not apply to claims for injury to persons or damage to property caused by the sole
negligence or fault of Kodak or by persons under its direction or control.
Kodak X-Omat
2000/2000A Processors to function properly for 1 year from the date of initial
Publication History
Affected
Print Date Pub No. ECO No.
Dec. 98 7C8770 N/A All om3554_1_03dec98.fm First Printing.
Jan. 99 7C8770 N/A Page 2 om3554_1_19jan99.fm Added safety notice.
Printed in U.S.A. • om3554_1.fm
Pages File Name Notes
Kodak
and
X-Omat
are trademarks.
EASTMAN KODAK COMPANY
Rochester, NY 14650
HEALTH IMAGING
Loading...