Kodak MDV434K User Manual

User guide

SMART. VERY SMART.

MDV434K

DIGITAL VIDEO DISC PLAYER

01-37 MDV434K_Eng_552 04/02/05, 4:13 PM1

General Information

Environmental Information

All unnecessary packaging has been omitted. The packaging has been made easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).

Your DVD player consists of materials which can be recycled and reused if disassembled by a specialised company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

Laser safety

This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.

NOTE: PICTURES SHOWN MAYBE DIFFERENT BETWEEN COUNTRIES.

CAUTION (WARNING LOCATION: ON THE BACKPLATE OF THE SET)

NEVER MAKE OR CHANGE CONNECTIONS WITH THE POWER SWITCHED ON.

For Customer Use:

Read carefully the information located at the rear of your DVD VIDEO player and enter below the Serial No. Retain this information for future reference.

Model No. MDV 434K Serial No. _______________

01-37 MDV434K_Eng_552 04/02/05, 4:13 PM2

LASER

Type Semiconductor laser

GaAlAs

Wave length 650 nm (DVD)

780 nm (VCD/CD)

Output Power 7 mW (DVD)

10 mW (VCD/CD)

Beam divergence 60 degree

Index

English --------------------------------------- 6

Español ------------------------------------ 38

Português --------------------------------- 72

English

Español

Português

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.

Due to the inconsistency of disc formats provided by various disc manufacturers, your DVD system may require a playability enhancement or upgrade. As DVD technology advances, these enhancements will become common and will be easy to complete.

01-37 MDV434K_Eng_552 04/02/05, 4:13 PM3

‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.’

Contents

English

Introduction

Supplied accessories ....................................... 6

Care and safety information.......................... 6

Connections

Connecting TV .............................................. 7-8

Using Composite Video jacks (CVBS) ........ 7

Using Component Video jacks (Pr Pb Y) ... 7

Using an accessory RF modulator .............. 8

Connecting the power cord.......................... 8

Optional : Connecting to an Audio System .

............................................................................. 9

Stereo system has Dolby Pro Logic or Right

/ Left Audio In jack ......................................... 9

Optional: Connecting Digital AV Receiver ...

............................................................................. 9

Receiver has a PCM, Dolby Digital, or

MPEG2 decoder .............................................. 9

Functional Overview

Front and Rear Panels .................................. 10

Remote Control ............................................ 11

Getting Started

Step 1: Inserting batteries into the

Remote Control ............................................ 12

Using the Remote Control to operate the

Player ............................................................... 12

Step 2: Setting up the TV ........................12-14

Setting up Progressive Scan feature (for

Progressive Scan TV only) ........................... 13

To deactivate Progressive manually .......... 14

Selecting the colour system that

corresponds to your TV .............................. 14

Step 3: Setting language preference ........... 15

Setting the OSD Language .......................... 15

Setting the Audio, Subtitle and Disc menu

language .......................................................... 15

Disc Operations

Playable Discs ................................................. 16

Region Codes ................................................. 16

Playing discs..................................................... 16

Basic playback controls................................. 17

Selecting various repeat/shuffle functions 17

Repeat play mode ......................................... 17

Repeating a section within a chapter/track .

.........................................................................

Operations for video playback ................... 18

Using the Disc Menu.................................... 18

Zooming in ..................................................... 18

Resuming playback from the last stopped

point ................................................................ 18

Slow motion................................................... 18

Using the OSD menu .................................. 18

Special DVD features .................................... 19

Playing a Title ................................................. 19

Camera Angle ................................................ 19

Changing the Audio Language .................... 19

Subtitles .......................................................... 19

Special VCD & SVCD Features ............. 19-20

Playback Control (PBC) .............................. 19

Preview ........................................................... 20

Playing MP3/JPEG/Kodak Picture CD ........ 21

General Operation ....................................... 21

Selecting a folder and track/file ................. 21

Special picture disc features ........................ 22

Preview Function .......................................... 22

Zoom picture ................................................ 22

Playback with multi-angles .......................... 22

Scan Effect ...................................................... 22

Karaoke Operations

Playing Karaoke discs .................................... 23

General Operation ....................................... 23

Key setting...................................................... 23

Vocal ................................................................ 23

Mode ............................................................... 23

01-37 MDV434K_Eng_552 04/02/05, 4:13 PM4

DVD Menu Options

General Setup menu ............................... 24-25

Locking/Unlocking the disc for viewing ... 24

Dimming system’s display screen .............. 24

Programming disc tracks .......................24-25

OSD Language ............................................... 25

Screen Saver - turning on/off ..................... 25

Sleep ................................................................ 25

Audio Setup Menu ................................... 26-28

Analogue output ........................................... 26

Digital Audio Setup................................ 26-27

Sound Mode ................................................... 27

Night Mode - turning on/off ....................... 28

Video Setup Menu ................................... 28-30

TV Type ........................................................... 28

Setting the TV Display ................................. 29

Progressive - turning on/off........................ 29

Picture Setting ............................................... 30

Preference Page........................................ 31-33

Audio, Subtitle, Disc Menu .......................... 31

Restricting playback by Parental Control .....

.................................................................. 31-32

PBC .................................................................. 32

Changing the Password ............................... 33

Restoring to original settings ..................... 33

Troubleshooting ......................... 34–35

Contents

English

Specifications ......................................36

Glossary ......................................................................37

Language Code............................................ 106

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM5

Introduction

10 cm

(4 inches)

10 cm

(4 inches)

10 cm

(4 inches)

PHILIPS

English

Supplied accessories

Composite video cable (yellow)

Audio cable (white, red)

Remote Control and two AA batteries

Care and safety information

● Power consumption

– When the system is switched to Standby mode, it is still consuming power. To disconnect the system from the power supply completely, remove the AC power plug from the wall jack.

● Avoid high temperatures, moisture,

water and dust

– Do not expose the player, batteries or discs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight.)

● Avoid condensation problem

– The lens may cloud over when the player is suddenly moved from cold to warm surroundings, making it impossible to play a disc. Leave the player in the warm environment until the moisture evaporates.

● Do not block the vents

– Do not operate the DVD Player in an enclosed cabinet, allow about 10 cm (4 inch) of free space all around the player for adequate ventilation.

● Care of the cabinet

– Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

● Finding a suitable location

– Place the player on a flat, hard, and stable surface.

● Disc handling

– To clean a CD, wipe it in a straight line from the center towards the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! – Write only on the printed side of a CDR(W) and only with a soft felt-tipped pen. – Handle the disc by its edge, do not touch the surface.

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM6

Connecting TV

AUDIO

V (Pr/Cr)

U (Pb/Cb)

S-VIDEO

VIDEO IN

COMPONENT

VIDEO IN

AUDIO OUT

V (Pr/Cr)

U (Pb/Cb)

S-VIDEO IN

VIDEO IN

COMPONENT VIDEO IN

COMPONENT

VIDEO IN S-VIDEO IN

V (Pr/Cr)

AUDIO OUT

U (Pb/Cb)

VIDEO IN

S-VIDEO

VIDEO IN

Connections

English

COMPONENT

VIDEO IN

V (Pr/Cr)

AUDIO

U (Pb/Cb)

IMPORTANT! – You only need to make

one video connection from the following options, depending on the capabilities of your TV system. – Connect the DVD system directly to the TV.

Using Composite Video jacks (CVBS)

1 Use the composite video cable (yellow) to

connect the DVD Player’s CVBS (VIDEO) jack to the video input jack (or labeled as A/V In, Video In, Composite or Baseband) on the TV (cable supplied).

2 To hear the sound of this DVD Player

through your TV, use the audio cables (white/red) to connect AUDIO OUT (L/ R) jacks of the DVD Player to the corresponding AUDIO IN jacks on the TV (cable supplied).

IMPORTANT! – The progressive scan video quality is only possible when using Y Pb Pr and a progressive scan TV is required.

Using Component Video jacks (Y Pb Pr)

1 Use the component video cables (red /

blue/green) to connect the DVD system’s Y Pb Pr jacks to the corresponding Component video input jacks (or labeled as Y Pb Pr) on the TV (cable not supplied).

2 To hear the sound of this DVD Player

through your TV, use the audio cables (white/red) to connect AUDIO OUT (L/ R) jacks of the DVD Player to the corresponding AUDIO IN jacks on the TV (cable supplied).

3 Proceed to page 13 for detailed

Progressive Scan set up.

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM7

Connections

~ AC MAINS

AUDIO OUT

V (Pr/Cr)

U (Pb/Cb)

S-VIDEO

VIDEO IN

COMPONENT VIDEO IN

OPEN/CLOSE

STOP

PLAY/

PAUSE

English

RF coaxial cable to TV

Back of RF Modulator

(example only)

AUDIO IN

TO TVINT IN

VIDEO

R L

CH3 CH4

Antenna or

Cable TV signal

IMPORTANT! – If your TV only has a single Antenna In jack (or labeled as 75 ohm or RF In,) you will need an RF modulator in order to view the DVD playback on the TV. See your electronics retailer for details on RF modulator availability and operations.

Using an accessory RF modulator

1 Use the composite video cable (yellow) to

connect the DVD Player’s CVBS jack to the video input jack on the RF modulator.

2 Use the RF coaxial cable (not supplied) to

connect the RF modulator to your TV’s RF jack.

Connecting the power cord

After everything is connected properly, plug in the AC power cord to the power outlet.

Never make or change any connections with the power switched on.

When no disc is loaded, press

STANDBY ON on the DVD Player front panel, “NO DISC” may appear on the display panel.

STOP

PLAY/

OPEN/CLOSE

NO DISC

PAUSE

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM8

Connections

AUDIO

DIGITAL

AV Receiver

Optional: Connecting to an Audio System

STEREO

AUDIO

DIGITAL

Stereo system has Dolby Pro Logic or Right / Left Audio In jack

1 Select one of the video connections

(CVBS VIDEO IN, SC ART or COMPONENT VIDEO IN) depending on the options available on your TV.

2 Use the audio cables (white/red) to

connect AUDIO OUT (L/R) jacks of the DVD Player to the corresponding AUDIO IN jacks on the stereo system (cable supplied).

Optional: Connecting Digital AV Receiver

English

Receiver has a PCM, Dolby Digital, or MPEG2 decoder

1 Select one of the video connections

(CVBS VIDEO IN, SCART or COMPONENT VIDEO IN) depending on the options available on your TV.

2 Connect the COAXIAL jack of the DVD

Player to the corresponding Digital Audio In jack on your Receiver (cable not supplied).

3 Set the DVD Player’s Digital Output to

PCM-ONLY or ALL depending on the capabilities of your Receiver (see page 26

“Digital Output”).

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM9

Helpful Hint: – If the audio format of the Digital Output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

Functional Overview

OPEN/CLOSE

MIC

LEVEL

STOP

PLAY/

PAUSE

TANDBY

English

Front and Rear Panels

STANDBY-ON B

– To switch the DVD Player to Standby

mode or ON

Disc tray

OPEN/CLOSE /

– Open/Close the disc tray

Display

– Shows the current status of the DVD

Player

STANDBY

-ON

– Microphone volume control

– For connecting microphone

LEVEL

MIC

– Point the remote control towards this

2; PLAY/PAUSE

– To start or interrupt playback

– To stop playback

OPEN/CLOSE

STOP

IR Sensor

sensor

9 STOP

PLAY/

PAUSE

MIC

LEVEL

Mains (AC Power Cord)

– Connect to a standard AC outlet

CVBS (VIDEO Out)

– Connect to CVBS Video input of a TV

YPbPr (Component Video Out)

– Connect to YPbPr input of a TV

– Connect to AUDIO inputs of an amplifier,

COAXIAL (Digital audio out)

Audio Out (Left/Right)

receiver or stereo system

– Connect to coaxial AUDIO input of a

digital audio equipment

Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM10

Remote Control

POWER B

– To switch the DVD player to

standby mode or ON

Functional Overview

PREVIEW

– To search chapter/track during

playback

English

0-9 numerical key pad

– Selects numbered items in a menu

RETURN/TITLE

– To go back to previous menu/show

title menu

– To search or select previous

chapter or track

PLAY ( B )

– To start playback

STOP ( 9 )

– To stop playback

– Not available for this model

– Acknowledge menu selection

DISC MENU

– Enters or exits the disc contents

– Switches on or off the playback

control mode (for VCD version

2.0 only)

REPEAT

– Selects various repeat modes

REPEAT (A-B)

– Repeats playback a specific section

on a disc

AUDIO

– To access audio language system

Helpful Hint: Press “STOP” for about 2 seconds to OPEN or CLOSE disc tray.

OPEN

– Open the disc tray

DISPLAY

– Displays information on TV

screen during playback

– To search or select next chapter

or track

PAUSE ( ; )

– To pause playback temporarily /

frame-by-frame playback

MUTE

– Disables or enables sound output

1 2 3 4

– Selects an item in the menu/ fast

forward/backward, slow forward/ backward

SYSTEM MENU

– Access or exit DVD Player’s

system menu

SUBTITLE

– To access subtitle language

system menu

ANGLE

– Selects a DVD camera angle

ZOOM

– Enlarge a picture on the TV

screen

MIC ON/OFF

– Display karaoke menu to set MIC

on or off

VOCAL

– Choose audio channels or

karaoke methods

MODE

– Display karaoke menu

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM11

PLAY/

PAUSE

Getting Started

English

Step 1: Inserting batteries into the Remote Control

1 Open the battery compartment. 2 Insert two batteries type R06 or AA,

following the indications (+-) inside the compartment.

3 Close the cover.

Using the Remote Control to operate the Player

1 Aim the Remote Control

directly at the remote sensor (IR) on the front panel.

2 Do not put any objects

between the Remote Control and the DVD Player while operating the DVD Player.

Step 2: Setting up the TV

IMPORTANT!

Make sure you have completed all the necessary connections. (See pages 7-8 “Connecting TV”).

1 Turn on the TV and set to the correct

video-in channel. You should see the DVD background screen on the TV.

2 Usually these channels are between the

lowest and highest channels and may be called FRONT, A/V IN, or VIDEO. See your TV manual for more details.

➜ Or, you may go to channel 1 on your

TV, then press the Channel down button repeatedly until you see the Video In channel.

➜ Or, the TV Remote Control may have a

button or switch that chooses different video modes.

TOP

PLAY/

PAUSE

➜ Or, set the TV to channel 3 or 4 if you

are using an RF modulator.

3 If you are using external equipment, (eg.

audio system or receiver), turn it on and select the appropriate input source for the DVD Player output. Refer to the equipment owner’s manual for detail.

CAUTION! – Remove batteries if they are exhausted or if the Remote Control is not being used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed properly.

01-37 MDV434K_Eng_552 04/02/05, 4:14 PM12

+ 25 hidden pages