Kodak i800, i810, i820, i830, i840 Instruction Manual

for Kodak Scanners

Cleaning and Consumable Replacement Instructions

I

M

anualnstruction

Versitec is a division of Cranel, Inc.

i820/i830/i840

i800/i810/

INSTRUCTION MANUAL FOR

KODAK

i800/i810/i820/i830/i840 Scanner

Versitec 1- 888 - 722 - 6548 www. versitec.com

TABLE OF CONTENTS

I. i800 Scanner Maintenance

Step One: Cleaning the Paper Path...........................2 - 3

Step T wo: Cleaning the Upper Transport area............3 - 6

Step Three: Cleaning the V ertical Transport area........6 - 8

Step Four: Cleaning the Transport area...................8 - 10

Step Five: Cleaning the Printer and Patchhead......10 - 11

Step Six: Cleaning the Imaging Guides ................12 - 13

II. i800 Maintenance and Replacing Procedures

Step One: Replacing the feed Module & feed

Module Tires............................................14

Step Two: Replacing the feed Module ....................14 - 15

Step Three: Replacing the feed Module Tires.........15 - 17

Step Four: Separation Roller and Tires........................ 18

Step Five: Replacing the separation Rollers ..........18 - 19

Step Six: Replacing the separation Roller Tires .............19

Step Seven: Changing the Separation Pad............19 - 20

Step Eight: Cleaning the feed Module Tires &

Separation Roller Tires ....................20 - 21

Versitec 1- 888 - 722 - 6548 www. versitec.com 1

i i

800800

I.

i

i i

This chapter provides cleaning and replacement procedures for
your scanner . For best scanner performance clean the areas
outlined in this chapter every 8-hour shift, unless otherwise noted.

Additional maintenance supplies can be ordering by calling DI
Supply or through your Kodak Reseller . For a list of available
supplies, see the section entitled, “Ordering Supplies” at the end of
this chapter .

All cleaning supplies can be disposed of in your normal

waste management system, unless otherwise noted.

Use the green handles when accessing scanner

Maintenance Maintenance

800

Maintenance

800800

Maintenance Maintenance

IMPORTANT

components.

Cleaning the paper path

The paper path should be cleaned with a Paper Path Cleaner fed

several times through the transport. T o clean the p aper path:

1 Remove the wrapping from the Paper Path Cleaner .
2 Adjust the feeder guides to the widest position.
3 Run the scanner in count-only mode.

See Chapter 3, Operator Control Panel Functions, for procedures.

2 Versitec 1- 888 - 722 - 6548 www. versitec.com

3 Feed the cleaning sheet (adhesive side up) in the landscape

orientation several times through the transport.

4 Feed the cleaning sheet (adhesive side down) in the landscape

orientation several times through the transport.

NOTE:

When a cleaning sheet gets dirty , discard it and use a new one.

Cleaning the upper transport area

Follow the steps below to clean the upper transport area:

1 Open the top cover.

Versitec 1- 888 - 722 - 6548 www. versitec.com 3

2 Open the bi-fold door .

3 Grasp the end of the lower imaging guide and slowly

pull it straight out.

4 Place the lower imaging guide on a clean surface.

5 Grasp the end of the upper imaging guide and slowly

pull it straight out.

4 Versitec 1- 888 - 722 - 6548 www. versitec.com

6 Place the upper imaging guide on a clean surface.

NOTE:

T o avoid getting any debris (from the cleaning process) on the

imaging guides, they will be reinstalled after the scanner is

thoroughly cleaned.

7 Release the top turn baffle.

T op turn
baffle

Exit

transport

plate

8 Vacuum the area.

9 Close the top turn baffle.

Versitec 1- 888 - 722 - 6548 www. versitec.com 5