KPT-801
Cinema Surround Speaker
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. ONLY USE attachments/accessories specified by the
manufacturer.
10. USE only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
DO NOT expose this apparatus to dripping or splashing and
ensure that no objects filled with liquids, such as vases, are
placed on the apparatus.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
EU COMPLIANCE INFORMATION:
Eligible to bear the CE mark, Conforms to European Union
EMC Directive 2004/108/EC.
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU) and Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE). This label
indicates that this product should not be disposed of
with household waste. It should be deposited at an
appropriate facility to enable recovery and recycling.
The lightning flash with arrowhead symbol within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock to persons.
WARNING: To reduce the risk of fire or electrical shock, do
not expose this apparatus to rain or moisture.
WARNING: No naked flame sources – such as candles –
should be placed on the product.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages
in this equipment are hazardous to life. No user-serviceable
parts inside. Refer all servicing to qualified service personnel.
KPT-801
The Klipsch KPT-801 is a two-way design using a high performance bass driver for the low frequencies. A Tractrix Horn
with a 90° x 90° coverage pattern is attached to a 1” diameter compression driver for clean and efficient reproduction
of the high and midrange frequencies.
WALL MOUNTING
Included with your speakers are “C” style mounting brackets
constructed of powder-coated zinc. These brackets attach to
the speaker with the supplied low profile knobs that thread
onto the top and bottom studs protruding from the cabinet.
This allows the speaker to be angled to the left or right when
mounted vertically, or up and down when mounted horizontally. When mounting horizontally, lock nuts are provided for
both studs for optimum speaker stability.
After determining the desired location and orientation of
your speakers, remove the bracket from the loudspeaker
and use it as a template to mark the location of the mounting holes. Check the alignment of the holes with a torpedo
level before drilling the pilot hole. Please observe local and/
or federal codes in securing the bracket, especially when
suspending objects above people’s heads. Once the bracket
is secured, affix the speaker to the bracket with the supplied
knobs. Be sure to leave enough clearance between the end of
the bracket and any adjacent wall or ceiling for installation of
the knobs.
CONNECTIONS
When making any type of speaker wire connection, be sure
to observe proper polarity. Most speaker wire and connectors are color-coded. Typically, red is positive (+) and black is
negative (–), or ground. It does not matter which wire conductor is connected to the positive or negative connection of
your equipment as long as it is consistent.
TYPES OF CONNECTORS
Your speaker is equipped with barrier strip connectors for
inputs. Make sure that there is no metal-to-metal contact
between the two lugs. Failure to observe this precaution at
either end of the connection can result in amplifier malfunction or damage.
If a wall stud is not available, use the appropriate type of
drywall or masonry anchor to support the weight of the
speaker, allowing for a generous safety margin. Please consult your dealer, custom installer or building contractor in
these situations.
You may also use an optional wall or ceiling mount that will
fit the provided 3/8” – 16 inserts.
PLACEMENT
SCREEN
Last 25% of wall or 25 ft.
Last surround within .25 (25%) of the length of the side.
100 ft. Wall
Each surround (after first on back wall 1.5 meters from wall)
placed 3 meters from each other.
The first surround 1.5 meters from the back wall.
On the back wall, the first surrounds are
placed 1.5 meters from the side walls, then
each surround is placed 3 meters from each
other until they meet in the middle. (Even
space them) so you are as close to 3 meters
distance between them as possible.
3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA
KLIPSCH.COM
©2013, Klipsch Group, Inc.
Klipsch Group, Inc. is a wholly-owned
subsidiary of Voxx International Corporation.
Loading...