Klipsch KI-272 Brochure

High Power
K I - 2 7 2
FREQUENCY RESPONSE
1
POWER HANDLING
2
MAXIMUM CONTINUOUS OUTPUT
3
DISPERSION ANGLE
DIRECTIVITY SENSITIVITY
4
NOMINAL IMPEDANCE
CROSSOVER FREQUENCY
OVERLOAD PROTECTION
COMPONENTS
ENCLOSURE MATERIAL
INPUT CONNECTIONS
DEPTH
HEIGHT
WIDTH
NET WEIGHT
SHIPPING WEIGHT
FINISHES
67Hz-12.5kHz±4dB, -10dB 50Hz (see graph) 250 Watts (41.2V) 125dB 60˚ Horizontal X 40˚ Vertical (see graph) 9dB (see graph) 101dB 8 Ohms, 6.8 Ohms Minimum at 180Hz (see graph) 1400Hz 12dB/Octave on LF 18dB/Octave on HF KLIP Overload Tweeter Protection Circuit K-42-KP 12" Woofer K-52-TI 1.5" Titanium Diaphragm Compression Driver 18mm 13-Ply Baltic Birch Plywood Cabinet 1" 11-Ply Birch Plywood Baffle Two NL-4 Speakon Connectors Wired in Parallel
16.5" (41.91cm) 23" (58.42cm)
16.813" (42.705cm) 52 lbs. (23.608kg) 59 lbs. (26.786kg) Black, White and Raw Birch
1
3M, Half-space anechoic
2
AES Standard, continuous pink noise 50Hz-10kHz, 6dB peaks
3
At 1M at power handling power input
4
SPLat 1M, half-space anechoic with 2.83V input
Archit ectu ra l S pe ci f ic at io ns
The KI-272 compact, high power, multiple angle loudspeaker system shall include a 12" (304.8mm) K-42-KP low-frequency transducer utilizing a 2.5" (63.5mm) voice coil and 77-ounce (2.18kg) magnet, and a high-frequency K-52-TI 1.5" (38.1mm) titanium diaphragm 20-ounce (622g) magnet compression driver mounted on a 60˚ X 40˚ heavy-duty, injection molded Tractrix Horn. Signal shall be applied to the transducers via a passive internal frequency-dividing network, incorporating a KLIP-circuit for signal overload protection of the high­frequency transducer. The enclosure tuning shall be of a vented design.
Frequency response shall be 67Hz to 12.5kHz, ±4dB, with the
-10dB point at 50Hz, measured at three meters, half-space anechoic. The high-frequency dispersion angle shall be 60˚ horizontal by 40˚ vertical nominal (refer to graph). Directivity shall be 9dB (refer to graph). Sensitivity shall be 101dB SPL, measured at one meter, half-space anechoic, with a 2.83V input. Power handling shall be 250 watts (41.5 volts), to AES standards, continuous pink noise, 50Hz to 10kHz, 6dB peaks. Maximum continuous output at one meter shall be 125dB SPL. Nominal impedance shall be 8 ohms, with 6.8 ohms minimum at 180Hz.
The internal passive crossover frequency shall be 1.4kHz, with slopes of 12dB/octave for the low frequency and 18dB/octave for the high frequency. The crossover may be modified for bi­amp application by cutting two easy-access internal wires. Signal connections shall be made via two parallel-wired Neutrik NL-4 Speakon panel mount jacks.
The enclosure panels shall be CNC-fabricated, 18mm, 13-ply Baltic Birch void-free plywood, assembled utilizing rabbet and dado joinery. The motorboard baffle shall be 1" (25.4mm) 11-ply birch plywood. Dimensions for the enclosure shall be 23" (58.42cm) high by 16.5" (41.91cm) deep by 16.813" (42.705cm) wide in a asymmetrical trapezoidal shape, with side panels angled at 65˚ and 45˚. Weight shall be 52 lbs. (23.608kg). The top and bottom panels shall be radiused, with a curved metal perforated grille for structural integrity and protection of the transducers from impact and tampering.
Enclosure flying capability shall be provided via 12 internal
3
/8" 16-thread mounting points, three per top, bottom and both
sides, with commercially available rigging bar compatibility.
The enclosure finish shall be lacquer-based primer and lacquer-based texture, with a black or white finish. The enclosure shall also be available unfinished in raw birch.
The system shall be a Klipsch KI-272 loudspeaker.
S p e c i f i c a t i o n s
45˚
©2000 Klipsch, LLC. All rights reserved. Specifications subject to engineering changes.
This symbol represents the center of gravity. This symbol indicates mounting point, 3/8-16 UNC threaded hole.
Front View
Left Side View
65˚
7.875
16.813 Ref
Top View
6.500
4.021
8.407 Ref
8900 Keystone Crossing, Suite 1220
Indianapolis, IN 46240
P.O. Box 688
Hope, AR USA71802
1-800-KLIPSCH • www.klipschpro.com
4.806
4.021
Back View
9.731
6.500
4.021
Right Side View
13.337
6.669
Bottom View
5M0200
190548
12"Two-way
Multiple Angle
Speaker System
The KI-272 is a high power
loudspeaker solution for limited space
is required. The speaker is perfect for
angled wall, corner, ceiling or
under-balcony mounting in theaters,
clubs, churches and schools. The
KI-272 also lends itself to slanted floor
or shelf mount use in high power
permanent install or corporate A/V
production environments, where
oblique angle projection is required.
Able to hang three-high using 12 built-in available rigging bar-compatible fly
“lock-joint” and rabbet construction
techniques on CNC-fabricated panels
To limit potential damage to the high
KLIP-circuit, a proprietary high-power
connection is with dual parallel-wired
The KI-272 is covered by the Klipsch
3
/8" 16-thread, commercially
points, the KI-272 provides the performance and reliability for
which Klipsch is known.
The 13-ply Baltic Birch void-free
plywood enclosure uses dado
for long-term reliability and
ruggedness.
frequency driver, the internal high-current passive full-range or bi-ampable crossover features the
thermal overload system. Signal
Neutrik NL-4 Speakon panel
mount jacks.
limited five-year warranty.
Multiple angle 45˚ and 65˚ asymmetrical design
12" woofer and 1.5" titanium diaphragm HF
compression driver
60˚ X 40˚ Tractrix®Horn for tight pattern control
12 suspension points for trouble-free mounting
Designed for difficult install locations or slant
floor use
13-ply, void-free Baltic Birch enclosure
Internal, high current full-range or bi-amp
passive crossover
KLIP-circuit HF driver protection device
K I - 2 7 2
HIGH POWER 12"TWO-WAY MULTIPLE ANGLE SPEAKER SYSTEM
Vertical 1/3 Octave Polars
Horizontal 1/3 Octave Polars
Frequency Response
Frequency
Horizontal Off-Axis Transfer Function
Impedance
115
105
95
85
75
Frequency
90
80
70
60
50
40
30
20
10
0
Directivity Index
12
6
0
0
-6
10 20 30
-12 40
-18
-24
-30
20
18
16
14
12
10
8
6
4
2
0
Frequency
Horizontal Coverage (-6dB)
Frequency
Vertical Off-Axis Transfer Function UP
Frequency
Vertical Coverage (-6dB)
360
315
270
225
180
135
90
45
0
Frequency
360
315
270
225
180
135
90
45
0
Vertical Off-Axis Function DOWN
12
6
0
0
-6
10 20 30
-12
40
-18
-24
-30
12
6
0
0
-6
10 20 30
-12 40
-18
-24
-30
Frequency
Frequency
Loading...