KDA-500
Filename: KDA500 Rear Panel Rev F.cdr
1 Color: White
SCI P/N: SLK800189
Rev: F
4 In x 4 Out 500W DSP AMPLIFIER
ETHERNET
RESET
SERVICE
ONLY
EXT. TRIG
+
UNBALANCED LINE IN
2 3
2 3
1
1
1
FOR DEFAULT 4-CHANNEL
4-OHM OPERATION, USE
UNBALANCED INPUTS 1 THRU 4.
4
4
INPUT 1 INPUT 2 INPUT 3 INPUT 4
GND+GND+GND+GND
+
1
BALANCED LINE IN
LINE OUT
2 3
HIGH PERFORMANCE POWER PLATFORM
The Klipsch KDA Series DSP Ampliers offer legendary
Klipsch power and performance in a sleek, high-tech, 1
rack unit solution. The KDA-500 offers 500W of class G/H
power, for clean, dynamic power in any type of install.
70V / 100V / LOW IMPEDANCE COMPATIBILITY
From small residential systems to massive commercial installs,
the Klipsch KDA-500 is designed for maximum install exibility
– offering low impedance and 70V/100V compatibility for
distributed line applications. These impedance settings are
fully independant from channel to channel – so an installer
can run one channel low impedance with another channel
70V/100V for full customization and optimization of their system.
FLEXIBLE I/O
The KDA-500 boasts fully matrixed 4x4 I/O with fully balanced
Phoenix connector inputs and Phoenix speaker outputs capable
of connecting up to 12 gauge wire. For non-balanced connections,
RCA inputs and outputs (throughs) are also built-in, making the
KDA-500 one of the most exible power solutions on the market today.
STATE-OF-THE-ART DSP CONTROL AND SET-UP
The myriad I/O, impedance, and acoustic settings are fully matrixed
and customizable through the web-based DSP menu - simply plug in a
laptop computer to the RJ-45 port on the back panel of the amplier,
enter the assigned IP address into your favorite web browser to pull
up the easy-to-use, streamlined menu page. In addition to password
protected channel assignments, gain settings, EQ, and limiting,
the DSP provides presets for almost every Klipsch speaker on the
market – optimizing acoustic performance and power handling for
these products with a single click. Accessing the DSP wirelessly
with a tablet, smartphone, or computer is also quick and easy when
the KDA amplier is plugged into the network’s wireless router.
4
CHANNEL1CHANNEL2CHANNEL3CHANNEL
+ + + +
70/100 VOLT+70/100 VOLT
SPECIFICATIONS
PART NUMBERS
AMPLIFIER TYPE
AMPLIFIER POWER
INPUTS
OUTPUTS
INPUT SENSITIVITY
INPUT IMPEDENCE
THD
SIGNAL-TO-NOISE
ENCLOSURE MATERIAL
RACK UNIT
PRODUCT DIMENSIONS
PRODUCT WEIGHT
MOUNTING
BUILT FROM
All specifications are subject to change without notice. ©2016 Klipsch Group, Inc. Klipsch, Keepers of the Sound and Tractrix are
SPEAKER OUTPUTS
+
110-120V/220-240V~50/60Hz 4A
ON
4
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE,
REPLACE ONLY WITH SAME
TYPE FUSE AND RATING.
ATTENTION:
UTILISER UN FUSIBLE DE
RECHANGE DE MEME
TYPE ET CALIBRE.
T4A L 250VAC
OFF
120V: 1063257
230V: 1063260
High Efficiency Class G/H
500W Total System Power
4 x 125W Per Channel
Balanced: 4 x Phoenix Line Level (up to 12 AWG wire)
Unbalanced: 4 x RCA Line Level
4 x Phoenix Speaker Level (up to 12 AWG wire)
4 x RCA Line Level (Throughs)
750mV Balanced, 0dBU
Balanced 40k
<1% @ Rated Output
-100dB Below Rated Output
Front Face: ABS Plastic
Case: Machine Formed Steel
1RU
1.73” x 19.02” x 14.29” (44mm x 483mm x 363mm)
15 lbs (6.82 kg)
Removable 1RU Rack Ears, Removable Rubber Feet
2016
3502 WOODVIEW TRACE INDIANAPOLIS, IN 46268 | KLIPSCH.COM
registered trademarks of Klipsch Group, Inc. a wholly-owned subsidiary of Voxx International Corporation.