ENGLISH
VISORCLR
Klein Tools Safety Helmet Visor is designed only to
be used with Klein Tools Safety Helmets.
GENERAL SPECIFICATIONS
• MATERIAL: Polycarbonate
• COMPLIANCE: ANSI Z87.1+ 2020, CSA Z94.3-20
• IMPACT: MIL-PRF-32432A (Class 1) Clause 3.8.4.1
• ANTI-FOG: EN166 Clause 7.3.2
• SCRATCH RESISTANCE: EN166 Clause 7.3.1
• OPTICAL CLASS I: EN166 Clause 7.1.2.1
• UV PROTECTION: ANSI Z87.1-U6
• IMPACT PROTECTION AT EXTREME
TEMPERATURES (FT): EN166 Clause 7.3.4
• OPERATING TEMPERATURE:
23°F to 131°F (-5°C to 55°C)
WARNINGS
Read all instructions. Failure to follow these warnings and
instructions may result in serious bodily injury or death.
•
Visors only PARTIALLY cover the face, so they provide
limited protection. Check with your safety supervisor to
ensure that the Visor is suitable for the application and it
meets all the approved safety standards.
•
Impact tested Visors DO NOT provide extraordinary
protection against flying particles, splash, spray,
and spatter. They are NOT unbreakable. They will
not provide protection against severe impacts like,
but not limited to, fragmenting grinding wheels,
shattering drill bits or cutting blades, high speed
projectiles, explosive devices, or molten metal.
•
If the Visor has sustained an impact, dispose of
it (and its components) IMMEDIATELY, even if
damage is not visible.
•
Shaded Visors should NEVER be used during any
type of welding or brazing operations.
•
The Visors DO NOT provide protection from extreme
heat or open flame. Special products designed for
high temperatures or open flame applications need
to be used in this case.
•
The Visors DO NOT provide any protection against
gases, vapors, infrared radiation, electromagnetic
radiation, and lasers.
•
NEVER alter, puncture, modify or engrave the Visor
or its components.
•
DO NOT use paints, solvents, chemicals, adhesives,
gasoline or like substances on this Visor–doing
so can lessen optical clarity and protection offered
against impact and penetration.
•
DO NOT use this Visor for vehicular, athletic, or
recreational uses.
•
DO NOT attach the Visors to other safety helmets
other than Klein Tools’ safety helmets-they will not
function as intended and will lead to injury or death.
•
Exposure to corrosive environments and/or extreme
temperatures below -30°F (-34°C) and/or above
115°F (46°C) can lessen the ability of the visor to
withstand impact and penetration.
MARKINGS ON PRODUCT (FIG.A)
Compliance standards:
1
• ANSI/ISEA Z87.1-2020
• CSA Z94.3-20
HARDWARE (FIG.B)
Threaded Support Brackets (Left & Right)
2
Thumb Screws
3
MAINTENANCE
INSPECTION: Inspect the Visor before and after
use, and immediately replace cracked, pitted,
scratched, deformed, and/or fogged Visors and
its components. ALL of the above defects will
greatly reduce the ability of the Visor to provide
adequate protection, resulting in injury or death.
CLEANING: Clean the Visor with mild soap and
water only. Wipe with soft dry cloth.
STORAGE: Store in a cool and dry place, away
from direct sunlight and corrosive environments.
Safety Helmet Visor -
FIG. A
VISORCLR
shown
mostrado
montre
FIG. B
2
VISORCLR
VISORGRAY
Instructions
VISORCLR
VISORGRAY
1
3
INSTALLATION / REMOVAL
PLEASE SEE REVERSE SIDE.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
1390361 Rev 06/20 A
ENGLISH
INSTALLATION
1. Insert the Left & Right Threaded Support
Brackets 2 into the slots on the Safety Helmet
as shown (FIG. C). NOTE: Make sure each
bracket is installed on the correct side of the
helmet (see markings on the brackets and
inside safety helmet: L = left, R = right). They
cannot be interchanged.
2. Press down until the Support Brackets snap
into place (FIG. D). NOTE: The brass insert
should align with hole in the Safety Helmet.
Make sure this is the case on both sides.
3. Align the visor locating holes with the holes in
the Safety Helmet (FIG. E).
4. Insert the Thumb Screws
holes as shown, and hand-tighten until there
are no visible gaps between the Thumb Screws
and the Visor (FIG. F). Do not over-tighten.
5. Slide the Visor up and down to ensure it stays
securely in both positions (FIG. G)
3
through locating
FIG. C
FIG. D
REMOVAL
1. Remove the Thumb Screws 3 and slide the
Visor off the Safety Helmet. NOTE: Store the
Visor and Thumb Screws in the original box
(or similar container) to protect the Visor from
damage and prevent the Thumb Screws from
getting lost.
2. It is not necessary to remove the Threaded
Support Brackets
removed from the Safety Helmet, as they will
be required to re-attach the Visor at a later
time. However, if the brackets do need to be
removed, insert a small flat screwdriver into
the slot(s) as shown to press the Bracket’s
release tab, then pull the Support Brackets out
of the Safety Helmet (FIG. H).
2
each time the Visor is
ACCESSORIES & REPLACEMENT PARTS
• VISORCLR (Clear Visor)
• VISORGRAY (Tinted Gray Visor)
FIG. E
FIG. F
FIG. G
FIG. H
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...