OPERATING INSTRUCTIONS
RATCHET SAFETY RELEASE:
Carefully turn the safety release knob counter-clockwise to release the ratchet mechanism.
(
TIP:
To ease safety release knob rotation, relieve the handle tension by slightly squeezing the handles
together while rotating the safety release knob.)
CUTTING CABLE (Fig 1.):
1.
Open the tool completely by squeezing the handles together fully to release the ratcheting mechanism.
2.
With the tool in the open position, insert the cable into the cable cutting cavity on the back of the tool.
3.
To cut the cable, carefully squeeze the handles together fully through a complete ratcheting cycle.
4.
When the cutting cycle is complete, the ratchet mechanism will release and the jaws will open.
5.
Remove the cable from the tool.
STRIPPING FLAT/RIBBON TYPE MODULAR CABLE (Fig. 2):
1.
Open the tool completely by squeezing the handles together fully to release the ratcheting mechanism.
2.
With the tool in the open position, insert the cable into the cable cutting cavity on the front of the tool.
4 and 6 conductor cable:
Insert the cable into the cable cutting cavity on the front side of the tool, and
position the cable towards the handle-side of the cavity. (
Note:
The raised depth gauge located inside
the cavity adjacent to the round, twisted-pair, cable stripper guide.) Insert the cable up to the raised
depth gauge.
8 conductor cable:
the cable towards the hinge-side of the cavity. Insert the cable until the end protrudes from the other
To strip the cable, carefully squeeze the handles together fully and hold in the closed position.
Pull the cable out while holding the handles together. The cable will be stripped to the correct length for
When finished pulling the cable through the stripping knives, release the handles. The ratcheting cycle is
Remove the cable jacket from the cutting knife cavity of the tool.
Follow the instructions below for crimping the connector to the cable.
Open the tool completely by squeezing the handles together fully to release the ratcheting mechanism.
With the tool in the open position, insert the cable into the round, twisted-pair, cable stripping cavity on
the front of the tool.
To strip the cable, carefully squeeze the handles together fully and hold in the closed position.
Carefully rotate the tool around the cable 3 to 5 times to score jacket.
DO NOT use the tool to pull the outer jacket off of the cable. This may damage the conductors and
the tool.
Complete the ratcheting cycle.
The ratchet mechanism will release and the jaws will open. Remove the scored twisted-pair cable from
the tool.
If blade penetrates the conductor insulation, cut
the cable and remove the damaged insulation. Repeat steps 1 through 6.)
Follow the instructions below for crimping the connector to the cable.
Assemble connector to prepared cable end, per the connector manufacturer’s instructions.
Verify the required “pin-out” configuration prior to crimping connector-cable assembly.)
See the chart (Fig. 4) to determine the appropriate cavity for the connector-cable assembly.
With the tool in the open position, insert the connector-cable assembly into the appropriate cavity
6P & 8P cavity located on front of tool (Fig. 5).
To compress the connector, carefully squeeze the handles together. When the crimping cycle is complete,
the ratchet mechanism will release and the jaws will open.
Remove the crimped cable assembly from the tool. Verify and test the connection.
abierta, inserte el cable en la cavidad de corte en la parte delantera de la
y
el cable en la cavidad de corte de cable en la parte delantera de la herra-
con cuidado ambos mangos juntos por completo y manténgalos
RJ11 o RJ12 para auriculares.
del cable pasándolo a través de las cuchillas de pelado, suelte los
de la cavidad de la cuchilla de corte de la herramienta
para ponchar el conector al cable
presionando ambos mangos juntos para liberar el mecanismo
abierta, inserte el cable en la cavidad de pelado de cable de par
trenzado
con cuidado ambos mangos juntos por completo y manténgalos
alrededor del cable de 3 a 5 veces para estriar la funda.
liberará y las mordazas se abrirán. Quite el cable de par trenzado estriado
Si la cuchilla atraviesa el
para ponchar el conector al cable.
(Fig. 5 y 6):
.
requerida de disposición de conectores antes de ponchar el conjunto
.
presionando ambos mangos juntos para liberar el mecanismo
posterior de la herramienta (Fig. 6).
de la herramienta. Verifique y pruebe la conexión
cuidadosamente em sentido anti-horário para liberar
apertando os dois cabos levemente enquanto gira o botão
aberta, insira o cabo a ser cortado na cavidade de corte de cabo na parte
VDV226-011
Pinza ponchadora/pelacables modular
Crimpador/descascador modular de catraca
Outil à sertir/dénuder modulaire à cliquet
ENGLISH
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...