Klein Tools Klein Tools CL200 Manual

Instruction

AUTO

A

AC

CL200

Instruction

ENGLISH

Manual

Manual

CL200

ENGLISH

• 3-3/4 DIGIT
3999 COUNT LCD

• AUTO / MANUAL
RANGE

• DATA HOLD

• BACKLIGHT

• WORKLIGHT

CL200

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools CL200 is a multi-featured clamp meter. It measures
AC / DC voltage, AC current, resistance, capacitance, frequency, duty cycle,
and temperature. It can also test diodes and continuity.

• Operating Altitude: 2000 meters

• Relative Humidity: 75% max

• Operating Temperature: 0°C / 32°F to 40°C / 104°F

• Storage Temperature: -10°C / 14°F to 50°C / 122°F

• Accuracy Temperature: 18°C / 64°F to 28°C / 82°F

• Temperature Coefficient: 0.1*(specified accuracy) / °C

• Sampling Frequency: 3 samples per second

• Dimensions: 8.2" x 3.0" x 1.4"

• Weight: 10.0 oz.

• Calibration: Accurate for one year

®

For Professionals...Since 1857

• CAT Rating: CAT III 600V

• Accuracy: ± (% of reading + # of least significant digits)

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring
a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep fingers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes
are connected.

• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,
replace batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out
power before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.

SYMBOLS

Visit us at www.TestEquipmentDepot.com

99 Washington Street
Melrose, MA 02176

Phone [phone]
Toll Free 1-800-517-8431

AC Alternating Current Warning or Caution

~

DC Direct Current Dangerous levels

DC/AC Voltage or Current Double Insulated Class II

Ground

AC Source

Safe for disconnect
from live conductors

ENGLISH

CL200

AUTO

A

AC

CL200

FEATURE DETAILS

H. Backlig ht / Worklight

• Hold button down to enable worklight and backlight.

• On release, lights will turn off automatically after 5 to 15 seconds.

• Worklight only operates during AC current measurement.

• Using lights drains the battery significantly.

Auto Power-Off

• Device will power off after 30 minutes non-use.

1

• Turn the dial or press a button to wake.

• Press the

HOLD

button while turning on to disable

Auto Power-Off feature.

H

B

G

On Back

FUNCTION INSTRUCTIONS

1

H
C

3

D
E

F

5

2

1. AC Current: < 600A

Features:

HOLD RANGE WORKLIGHT

4

A

A. Use CAT III rated leads or higher.

Do not attempt to measure more than 600V or

any current on lead input.
B. Keep hands below line when measuring high current levels.
C. Select Functionality Button

• Switch between AC and DC.

• Switch between

D. Data Hold

• Press to hold the current input on the display.

• Press again to return to live reading.

E. Auto / Manual Range

• Press repeatedly to cycle through manual ranges.

• Hold for 2 seconds to return to auto ranging mode.

AUTO

•

F. G. Battery Replacement

• When
batteries must be replaced.

• Remove the back screw and replace 3 x AAA batteries.

Ω, , , and .

is displayed on LCD only during auto ranging mode.

indicator is displayed on the LCD,

• Center wire in guides for best accuracy.

• Opposing currents cancel (use line-splitter when necessary).

2. AC / DC Vol tage: < 600V

Features:

HOLD RANGE

PRESS

AUTO

AC

A

• Select AC or DC voltage source.

3. Freq uency (Hz) / Dut y Cy cle

Features:

HOLD

PRESS

Duty

AUTO

AC

A

ENGLISH

4. Temperature: -4° ≤ °F ≤ 1832°

Features:

HOLD

AC

A

• Use included thermocouple.

5. Resis tance / Capac itance / Diode / Cont inuity

PRESS

TO SELECT

Resistance

Diode

Capacitance
Continuity

AUTO

AC

A

Resistance Features:

HOLD RANGE

• Ω < 40MΩ

•

Do not measure resistance

on a live circuit.

AUTO

AC

A

Capacitance Features:

HOLD RANGE

• F < 100μF

• Wait up to 60 seconds for measurement.

•

Safely discharge capacitor before

measurement.

AUTO

AC

A

Diode Features:

HOLD

Display shows:

• Forward voltage drop if forward biased.

• “O.L.” if reverse biased.

AUTO

AC

A

Continuity Features:

HOLD

• Display shows resistance.

• Buzzer sounds if less than 60Ω

SYMBOLS USED ON LCD

AC Measurement DC Measurement

~

Negative DC Value

-

Low Battery
Hold Active Diode Test

H

Voltage Measurement Continuity Test

V

Frequency in Hertz

Hz

Capacitance in Farads

F

Resistance in Ohms

Ω

m

n

Milli 10
Nano 10

-3

-9

AUTO

Auto Range Active
Current in Amps

A

Duty Cycle

%

Temperature in Fahrenheit

F

°

Mega 10

M

Kilo 10

k

μ

Micro 10

ELECTRICAL SPECIFICATIONS

DC Voltage Measurement

Range Resolution Accuracy

400mV 0.1mV
4V 0.001V
40V 0.01V
400V 0.1V
600V 1V ± (1.0% + 2 digits)

Overload Protection: 600V DC / AC
Input Impedance: 10MΩ.

AC Voltage Measurement

Range Resolution Accuracy

400mV 0.1mV
4V 0.001V
40V 0.01V
400V 0.1V
600V 1V ± (1.2% + 10 digits)

Overload Protection: 600V DC / AC
Frequency: 40 to 400Hz
Input Impedance: 10MΩ.
Response: Averaging

AC Current Measurement

Range Resolution Accuracy

4A 0.001A ± (3.5% + 20 digits)
4A 0.001A ± (3.0% + 10 digits) > 0.5A
40A 0.01A ± (3.0% + 10 digits)
400A 0.1A ± (2.5% + 10 digits)
600A 1A ± (1.5% + 5 digits)

Overload Protection: 720A for 60 sec. max
Frequency: 50 to 60Hz
Response: Averaging

Resistance Measurement

Range Resolution Accuracy

400Ω 0.1Ω
4kΩ 0.001kΩ
40kΩ 0.01kΩ
400kΩ 0.1kΩ
4MΩ 0.001MΩ
40MΩ 0.01MΩ ± (2.0% + 5 digits)

Overload Protection: 600V DC / AC

6

3

-6

± (0.8% + 2 digits)

± (1.0% + 10 digits)

± (1.2% + 2 digits)

≤

0.5A

ENGLISH

Capacitance Measurement

Range Resolution Accuracy

50nF 0.01nF ± (3.0% + 10 digits)
500nF 0.1nF
5μF 0.001μF
50μF 0.01μF

± (3.0% + 5 digits)

100μF 0.1μF

Overload Protection: 600V DC / AC

Frequency Measurement

Range Resolution Accuracy

50Hz 0.01Hz
500Hz 0.1Hz
5kHz 0.001kHz

± (0.1% + 3 digits)
50kHz 0.01kHz
100kHz 0.1kHz

Overload Protection: 600V DC / AC

Duty Cycle Measurement

Range Resolution Accuracy

0.1 ˜ 99.9% 0.1% ± (3.0% + 0 digits)

Overload Protection: 600V DC / AC

Temperature Measurement

Range Resolution Accuracy

-4 ˜ 1832°F 1°F ± (3.0% + 3 digits)

Overload Protection: 600V DC / AC

Diode Test

Overload Protection Resolution Open Circuit Voltage

600V DC / AC 1mV Appx. 1.5V

Continuity Test

Overload Protection Resolution Open Circuit Voltage

600V DC / AC 100mΩ Appx. 0.45V

WARRANTY

This product is warranted to be free from defects in materials and workmanship
for a period of two years from the date of purchase. During this warranty period,
Klein Tools has the option to repair or replace or refund the purchase price of
any unit which fails to conform to this warranty under normal use and service.
This warranty does not cover damage which occurs in shipment or failure which
results from alteration, tampering, accident, misuse, abuse, neglect, or improper
maintenance. Batteries and damage resulting from failed batteries are not
covered by warranty. A purchase receipt or other proof of original purchase date
will be required before warranty repairs will be rendered.

Any implied warranties, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the express
warranty. Klein Tools shall not be liable for loss of use of the instrument or other
incidental or consequential damages, expenses, or economic loss, or for any
claim or claims for such damage, expenses or economic loss.

Some states or countries laws vary, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. If your Klein product requires
repair or for information on how to exercise your rights under the terms of this
warranty, please contact Klein Tools at 1-877-775-5346.

CLEANING

Turn instrument off and disconnect test leads. Clean the instrument by using
a damp cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of
time. Do not expose to high temperatures or humidity. After a period of storage
in extreme conditions exceeding the limits mentioned in the Specifications
section, allow the instrument to return to normal operating conditions before
using it.

DISPOSAL / RECYCLE

Caution: This symbol indicates that equipment and its accessories

shall be subject to a separate collection and correct disposal.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

www.kleintools.com

139560T