Klein Tools ET200 User Manual [en, es, fr]

ENGLISH

Continuity Testing

Continuity is indicated at less than 270kΩ of resistance.

600

480

277

240

208

120

48

24

12

GFCI Testing

Check the GFCI Receptacle user manual for more information.

Always contact a qualified electrician to resolve wiring problems.

Operate the Push Button on the GFCI Receptacle. If the GFCI circuit

does not trip, the receptacle is not operating properly.

To test the functionality of a Ground Fault Circuit Interrupter receptacle,
apply leads to the hot and ground terminals for 7 seconds.

• If the GFCI receptacle is wired properly, power to the circuit
will go out and the ET200 will stop indicating voltage.

• If the GFCI receptacle is wired improperly, power to the circuit
will remain and the ET200 will continue to indicate voltage.
To resolve an issue, contact a qualified electrician.

Battery Replacement

Batteries are not required for visual voltage indication.

1. Remove test leads from voltage source.

2. Unscrew battery cover and replace 3xAAA batteries.

600

WARRANTY

This product is warranted to be free from defects in materials and workmanship
for a period of two years from the date of purchase. During this warranty period,
Klein Tools has the option to repair or replace or refund the purchase price of
any unit which fails to conform to this warranty under normal use and service.
This warranty does not cover damage which occurs in shipment or failure which
results from alteration, tampering, accident, misuse, abuse, neglect, or improper
maintenance. Batteries and damage resulting from failed batteries are not
covered by warranty. A purchase receipt or other proof of original purchase date
will be required before warranty repairs will be rendered.

Any implied warranties, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the express
warranty. Klein Tools shall not be liable for loss of use of the instrument or other
incidental or consequential damages, expenses, or economic loss, or for any
claim or claims for such damage, expenses or economic loss.

Some states or countries laws vary, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. If your Klein product requires
repair or for information on how to exercise your rights under the terms of this
warranty, please contact Klein Tools at 1-800-553-4676.

CLEANING

Clean the instrument by using a damp cloth. Do not use abrasive cleaners or
solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of
time. Do not expose to high temperatures or humidity. After a period of storage
in extreme conditions exceeding the limits mentioned in the Specifications
section, allow the instrument to return to normal operating conditions before
using it.

DISPOSAL / RECYCLE

Caution: This symbol indicates that equipment and its accessories

shall be subject to a separate collection and correct disposal.

Instruction
Manual

ET200

ENGLISH

• AC/DC
VOLTAGE
TO 600V

• CONTINUITY
FUNCTION

• WORKLIGHT

• LIGHT, VIBRATION, SOUND INDICATORS

• CAT IV 600V SAFETY RATING

• MODERN SOLID-STATE DESIGN

QuickTime™ and a

600

480

277

240

208

120

48

24

12

®

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-800-553-4676

www.kleintools.com

139575TRev. 05/10

www.kleintools.com

F o r P r o f e s s i o n a l s . . . S i n c e 1 8 5 7

ENGLISH

ET200

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools ET200 is a solid-state electrical tester. It measures AC/DC
voltage, tests continuity, and features a bright LED worklight.

• Voltage Level Indicators: 12, 24, 48, 120, 208, 240, 277, 480, 600

• Voltage Type Indicators: AC, DC Positive, DC Negative

• AC Frequency: 45Hz to 66Hz

• Maximum Voltage To Earth Ground: 600V RMS

• Maximum Measurable Voltage: 600V RMS (displayed by LEDs)

• Input Impedance: 15kΩ on connection, up to 150kΩ steady-state.

• Continuity: < 270kΩ

• Usage Duty Cycle (Above 277V): 1 minute on, 5 minutes off

• Accuracy: 70% to 100% of indicated voltage

• Battery Type: 3 x AAA

• Operating Altitude: 2000m

• Relative Humidity: 0°C to 30°C (32°F to 86°F) 90%

30°C to 40°C (86°F to 104°F) 75%
40°C to 55°C (104°F to 131°F) 45%

• Operating Temperature: 0°C to 55°C (32°F to 131°F)

• Storage Temperature: 0°C to 55°C (32°F to 131°F)

• Dimensions: 7.375 x 2.375 x 1.25”

• Weight: 8.1oz.

• Safety: CSA C22.2-1010.1, IEC 61010-1, Pollution Degree II

• CAT Rating: CAT IV 600V, CAT III 1000V

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring
a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep fingers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes
are connected to a voltage source.

• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.

• Shut off and lock out power before testing continuity.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.

SYMBOLS

Positive DC Voltage Warning or Caution

+

Negative DC Voltage Dangerous levels

–

AC Voltage Double Insulated Class II

~

Earth Ground ETL Certification

This product has been tested to the requirements of
CAN/CSA-C22.2 No. 61010-1, second edition, including

QuickTime™ and a

Photo - JPEG decompressor

are needed to see this picture.

Amendment 1, or a later version of the same standard
incorporating the same level of testing requirements

CAT III CAT IV

Designed for transient protection
on indoor measurements at
installations connected directly
to the primary source. Examples
include distribution panels and
lighting systems in large buildings.

Designed for transient protection
on outdoor measurements taken
at the primary supply voltage
source. Examples include outdoor
overhead or underground utility
service and electricity meter.

FEATURE DETAILS

Indicators
Lights

• LEDs light up numerical voltage level indicators,
as well as AC and DC

• Continuity LED will light up on detection.

• Voltage detection will function without batteries installed.

Vibration

• Instrument will vibrate in the presence of voltage
measurements greater than 48V.

• Vibration will function only with batteries installed.

Sound

• Instrument will emit a tone in the presence of voltage
measurements greater than 48V.

• Instrument will emit a tone on detection of continuity.

• Sound will function only with batteries installed.

Accuracy

Accuracy of indicator lights is 70% to 100% of the voltage displayed
to account for normal variations in supply voltage.

Worklight

Press the light bulb button above the Klein Tools logo to toggle the
worklight on and off.

Ghost Voltages

The approximate input resistance of 15k
false readings due to ghost voltages on de-energized lines.

Lead Spacing

Molded lead holders on the back of the ET200 are spaced correctly
to test tamper-resistant outlets.

+ or DC – indicators.

Ω will reduce the possibility of

OPERATING INSTRUCTIONS

Measuring Voltages

Time spent operational at voltages above 277V must be less than

60 seconds, with a cool-off time of at least 5 minutes.

Tester will turn on automatically when voltage is applied.

600

480

277

240

208

120

48

24

12

AC Voltage Measurement

600

480

277

240

208

120

48

24

12

DC Voltage Measurement

120

48

24

12

120

48

24

12