Klein Tools CL3200 User Manual [en, es, fr]

Instruction

AUTO

Manual

CL3200

ENGLISH

• AUTO VOLTAGE CURRENT DETECTION

• BACKLIGHT

• WORKLIGHT

• LOW Z

• BAR GRAPH

• DATA HOLD

• 3-3/4 DIGIT

3999 COUNT LCD

• AUTO RANGE

• NON CONTACT

VOLTAGE TESTER

HOLD

www.kleintools.com

For Professionals...Since 1857

ENGLISH

CL3200

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools CL3200 is an auto-ranging general-purpose clamp meter. It measures AC / DC voltage, AC current, and resistance. It can also test non-contact voltage and continuity.

• Operating Altitude: 2000 meters

• Storage Altitude: 10000 meters

• Humidity: 0% to 80% at 32°F to 95°F (0°C to 35°C)

0% to 70% at 32°F to 131°F (0°C to 55°C)

• Operating Temperature: 0°C / 32°F to 40°C / 104°F < 75% R.H.

• Storage Temperature: -20°C / -4°F to 60°C / 140°F < 80% R.H.

• Accuracy Temperature: 18°C / 64°F to 28°C / 82°F

• Temperature Coefﬁcient: 0.1*(speciﬁed accuracy) / °C

• Dimensions: 7.06" x 2.56" x 1.34"

• Weight: 7.9oz.

• Calibration: Accurate for one year

• Certiﬁcations: UL & cUL standard UL3111-1 Listed

• Pollution Degree: 2

• CAT Rating: CAT IV 600V, CATIII 1000V

• Accuracy: ± (% of reading + # of least signiﬁcant digits)

WARNINGS

To ensure safe operation and service of the tester, follow these instructions. Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring

a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep ﬁngers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected.

• Use caution when working with voltages above 60V DC,

or 25V AC RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out

power before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.

SYMBOLS

AC Alternating Current Warning or Caution

DC Direct Current Dangerous levels

DC/AC Voltage or Current Double Insulated Class II

Ground

AC Source

FEATURE DETAILS

Safe for disconnect from live conductors

FEATURE DETAILS

A. Use CATIII 1000V or CAT IV 600V rated leads or higher. Do not attempt to measure more than 1000V DC or 750V AC B. Keep hands below line when measuring high current levels. C. Auto Power-Off (Apo)

• Device will power off after 30 minutes non-use.

• Turn the dial or press a button to wake.

• Holding HOLD button while turning on disables Auto Power-Off.

D. Hold / Backlight / Worklight

• Press to hold the current input on the display.

• Press again to return to live reading.

• Press for 2 seconds to enable / disable lights.

• Using lights decreases battery life.

E. F. Battery Replacement

• When indicator is displayed on the LCD, batteries must be replaced.

• Remove the back screw and replace 2 x AAA batteries.

G. Magnetic Back

• Attach instrument to metal for hands-free use.

H. Bar Graph

• The bar graph shows an approximate analog representation of a measurement.

• The bar graph responds much faster than the digital display.

• The scale of the bar graph is zero to the maximum reading of

the selected range.

1 2

FUNCTION INSTRUCTIONS

5 2 4

1. AC Current: < 200A

• Center wire in guides for best accuracy.

• Opposing currents cancel (use line-splitter when necessary).

2. AC / DC Voltage: < 750V AC or 1000V DC AC / DC Voltage (Low Z): < 600V

• The tester will automatically choose AC voltage or DC voltage or AC current based on the inputs detected.

• AUTO will be displayed when no input is detected.

• DO NOT Use low impedance (Low Z) mode at voltages greater

than 600 V.

• Use low impedance (Low Z) mode to reduce ghost voltages.

3. Resistance: < 40MΩ

• Do not measure resistance on a live circuit.

4. Continuity

• Display shows resistance.

• Buzzer sounds if less than about 40Ω.

5. Non Contact Voltage (NCV): > 25V AC

• NCV works independently of other tester functions. The function knob can be in the off position.

• Press and hold.

ENGLISH

SYMBOLS USED ON LCD

AC Measurement DC Measurement

Negative DC Value

Overload: Range Exceeded

.L.

Low Battery

Voltage Measurement

Resistance in Ohms Continuity Test

Kilo 10

ELECTRICAL SPECIFICATIONS

DC Voltage Measurement

Range Resolution Accuracy

1.0V ~ 1000V 0.001V ~ 1V

-1.0V ~ -1000V 0.001V ~ 1V

Overload Protection: 1000V

Input Impedance (Nominal): >10MΩ, < 100pF

AC Voltage Measurement

Range Resolution Accuracy

1.2V ˜ 750V 0.001 ~ 1V ± (1.5% + 3 digits)

Overload Protection: 750V RMS Frequency Response: 45 to 400 Hz Response: Averaging

Input Impedance (Nominal): >10MΩ, < 100pF Input Impedance (Low Z) >3kΩ, <200pF, up to 600V RMS

AC Current Measurement

Range Resolution Accuracy

0.9A ~ 200A 0.1A ± (2.0% + 8 digits)

Overload Protection:

• Current: 200A Frequency: 45 to 1kHz Response: Averaging

Resistance Measurement

Range Resolution Accuracy

400Ω ˜ 4MΩ 0.1Ω ˜ 0.001MΩ ± (1.0% + 4 digits)

40MΩ 0.01MΩ ± (2.0% + 4 digits)

Overload Protection: 600V RMS

Continuity Test

Overload Protection Open Circuit Voltage Threshold (Appx.)

600V RMS

Overload Protection: 600V RMS

Non Contact Voltage Detector

On Voltage

Appx. 25V AC and above

0.44V < 40Ω

Auto Range Active

Auto Power-Off Active

Apo

HOLD

Hold Active

Current in Amps

Mega 10

± (1.0% + 4 digits)

WARRANTY

This product is warranted to be free from defects in materials and workmanship for a period of two years from the date of purchase. During this warranty period, Klein Tools has the option to repair or replace or refund the purchase price of any unit which fails to conform to this warranty under normal use and service. This warranty does not cover damage which occurs in shipment or failure which results from alteration, tampering, accident, misuse, abuse, neglect, or improper maintenance. Batteries and damage resulting from failed batteries are not covered by warranty. A purchase receipt or other proof of original purchase date will be required before warranty repairs will be rendered.

Any implied warranties, including but not limited to implied warranties of merchantability and ﬁtness for a particular purpose, are limited to the express warranty. Klein Tools shall not be liable for loss of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for such damage, expenses or economic loss.

Some states or countries laws vary, so the above limitations or exclusions may not apply to you. This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state. If your Klein product requires repair or for information on how to exercise your rights under the terms of this warranty, please contact Klein Tools at 1-877-775-5346.

CLEANING

Turn instrument off and disconnect test leads. Clean the instrument by using a damp cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the Speciﬁcations section, allow the instrument to return to normal operating conditions before using it.

DISPOSAL / RECYCLE

Caution: This symbol indicates that equipment and its accessories

shall be subject to a separate collection and correct disposal.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

www.kleintools.com

139680

+ 16 hidden pages