Klein Tools AEPJS3 User manual

Klein Tools AEPJS3 is a powered speaker designed to provide high-quality

sound for smart phones, tablets, computers, or other audio devices. The AEPJS3 will also charge common mobile devices like cell phones, tablets, headphones, and other smaller USB devices.

CONTENTS

• AEPJS3 Bluetooth® Speaker

• 39.4" (1000mm) USB-A to USB-C Cable

• 23.6" (600mm) 1/8" (3.5 mm) Auxiliary Cable

• Instruction Sheet

GENERAL SPECIFICATIONS

• Dimensions:

• Weight:

• Wireless Compatibility:

• Wireless Connection Range:

• Support Pro les: AD2P, AVRCP, HFP, SPP

• Battery Type:

• Battery Life:

• Certi cations:

• Operating/Charging Temperature:

• Storage Temperature:

• Relative Humidity:

• Drop Protection:

• Ingress Protection (IP) Rating:

Specifications subject to change.

5.46" x 5.37" x 2.33" (139 x 136 x 59 mm)

1.14 lb. (517 g)

Internal, Li-Ion, 3.63V / 5200mAh

20+ hours at 70% volume

CE, FCC, IC, BC, NOM

Devices with Bluetooth® Version 4.2

100 ft. (30 m) in open space

-22° to 140°F (-30° to 60°C)

<85% non-condensing

6.6' (2 m)

32° to 104°F (0° to 40°C)

IP54

WARNINGS

Read, understand, and follow these instructions to ensure safe operation. Failure to observe these warnings can result in risk of fire or electric shock. Keep these instructions for future reference.

• No user-serviceable parts inside. Do not open enclosure or attempt to repair this speaker.

• Never lubricate any part of this speaker.

• Do not expose to direct sunlight, open flame, heat sources, equipment that produces heat, or extremes in environmental temperature.

• Never immerse in water or other liquids. Do not allow liquids, dust or debris to enter openings or vents on the speaker enclosure.

• Water-resistant cover must be properly sealed to achieve specified water & foreign object ingress protection. Keep seal free of dirt, oil, sand, or other material that interferes with proper sealing. Failure to do so can result in risk of fire or electric shock.

• Do not open water-resistant cover if wet or in a wet environment. Dry the speaker thoroughly and the seal around water-resistant cover completely before opening water-resistant cover.

• When speaker is in use or charging, make sure there is adequate space to allow ventilation of internally generated heat.

• Use safety-rated power supply or wall adapter. Never use power supply or wall adapter that exceeds the specified charging voltage and current.

• Route the power supply cable so that it will not to be stepped on or pinched by other objects.

SYMBOLS ON PRODUCT

Warning or Caution Strong Magnetic Field Risk of Electrical Shock Read Manual Conforms with particular Code of Federal regulations Meets CEC and DOE energy ef ciency requirements

Canada Energy Ef ciency Veri ed This product has been independently tested by Intertek and

meets applicable published standards NOM-NYCE – IFETEL

Do not place equipment and its accessories in the trash Recycle

Conformité Européenne: Conforms with European Economic Area directives

FEATURE DETAILS (FIG.A)

Power Button

Skip Backward Button

Play/Pause/Talk Button

Skip Forward Button

Daisy Chain Button

“-“ Volume Down Button

“+” Volume Up Button

Voice Control Button

Bluetooth® LED Indicator

Battery Status Indicator

Daisy Chain LED Indicator

Nail Hook

Magnets (×2)

Auxiliary “Aux In” Jack

USB A Charge Out Port

USB C Charge In/Out Port

Water/Dust-Resistant Cover

AEPJS3

Bluetooth® Speaker with Magnet and Hook – Instructions

FIG. A

TOP

1 49 2 5

610 7 8

BACK

131312

113

SIDE

BOTTOM

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Klein Tools, Inc. is under license.

MAINTENANCE

CLEANING:

lint-free cloth. STORAGE: If the speaker is to be left unused for an extended period of

time, charge before storing, and recharge periodically during storage, to maintain battery's charging capacity.

Be sure speaker is turned off and wipe with a clean, dry

Do not use abrasive cleaners or solvents.

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. Please see epa.gov/recycle for additional information.

Find Quality Products Online at: sales@GlobalTestSupply.com

www.GlobalTestSupply.com

CHARGING BATTERY

OPERATING INSTRUCTIONS

NOTE: Fully charge before use. First-time charge should be at least 4 hours.

Connect the USB Type C cable connection to USB charging port 16; plug the other end of cable to computer or USB AC adapter or other USB power supply (not included). Charge times will vary: 5V-2.4A Charger - Approx. 3 Hours, 5V-1.0A Charger: Approx. 5 Hours. The battery level indicator will illuminate to indicate charging status (see table below).

CHARGING STATUS LED INDICATORS

Not

Illuminated Solid Yellow Solid Green Solid Red Blinking

LED

Status % Charged

Cascading Green Cascading Green Cascading Yellow Cascading Red

Cascading Green Cascading Green Cascading Yellow Solid Red

Cascading Green Cascading Green Solid Yellow Solid Red

Blinking Green Solid Green Solid Yellow Solid Red

Solid Green Solid Green Solid Yellow Solid red

ON/OFF: Press & hold power button 1 for 3 seconds, a tone will sound. Unit will automatically power off after 20 minutes of inactivity.

NOTE:

Turn unit off when not in use to prolong battery life.

PAIRING: Wireless connection activates automatically and is ready to pair when unit is turned on. On your Bluetooth scan for devices that can be paired. Select “AEPJS3” when it appears (refer to the user manual of your device). If necessary, enter “0000” as pairing passcode. A tone sounds after a successful pairing.

NOTE: Unit automatically attempts to connect the last paired wireless device but is ready to pair with any compatible device if the last paired device is not detected within 5 seconds of powering on.

DISCONNECT PAIRING:

1) Turn unit off; -or

2) Double-press Power Button

3) Plug a cable into Aux jack

4) turn off Bluetooth RESET WIRELESS CONNECTION OR PAIRING WITH DIFFERENT DEVICES:

Double-press Power Button 1 (tone sounds). Repeat Pairing procedure with different devices.

PLAYING AUDIO: Use your device to control the speaker or use the built-in control buttons on the speaker.

• Press the Play/Pause/Talk button

• Press the “-” maximum volume is reached. Volume may also be controlled from your audio device.

• Press the Skip Forward forward (respectively) during a song.

AUXILIARY AUDIO-IN: Connect one end of the auxiliary cable to the AUX jack speaker; plug the other end of cable to line-out or headphone jack of your device.

SPEAKERPHONE OPERATION:

• When an incoming call occurs, playing music is muted & ring tone sounds. Shortpress Play/Pause/Talk

• To disconnect the call, short press the Play/Pause/Talk button

DAISY-CHAINING: Once you have your AEPJS3 Speaker connected to a Bluetooth you can connect a second AEPJS3 speaker to your already connected AEPJS3 speaker.

1. Ensure your primary AEPJS3 speaker is turned on.

2. Turn on your secondary AEPJS3 speaker.

3. Press the Daisy Chain button

4. Upon successful connection, a tone will sound on both speakers and the Daisy Chain

5. To disable daisy-chaining, press the daisy-chain button on either of the two speakers.

NOTE: The daisy chain connection between the two AEPJS3 speakers will NOT automatically reconnect after the speakers are turned off. To reconnect, follow the Daisy-chaining steps above.

VOICE CONTROL: Press the voice control button 8 to activate the voice assistant on your device.

button on both AEPJS3 speaker and the Daisy Chain LED

will remain lit.

LED

after pressing the daisy chain button, the speaker will exit the daisy-chain mode.

wireless compatible device, enable Bluetooth® and search/

. Bluetooth® LED Indicator 9 will blink; -or

; -or

wireless connection in paired device.

or “+” 7 button to adjust the speaker volume. A tone will sound when

or Skip Backward 2 buttons to skip backward or

button to answer the call, or long-press to ignore.

NOTE: If daisy-chain connection is not established 30 seconds

0% to 24% charged

25% to 49% charged

50% to 74% charged

75% to 99% charged

100% charged

to play or pause audio on your device.

on both AEPJS3 speakers. Press the Daisy Chain

NOTE: Before using this function, the devices must be connected to the speaker via Bluetooth

LOW BATTERY INDICATION: The Red LED on the Battery Status Indicator

on/off when battery level drops to approximately 5%. Speaker will automatically power off when the battery level is below 2%. Recharge speaker as soon as possibleThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.

Cascading

to hang up.

will blink.

will flash

of the

device,

OPERATING INSTRUCTIONS

POSITIONING SPEAKER:

• Make sure that front of speaker is not obstructed.

• Stand speaker upright on a flat, level, stable surface.

• Attach speaker to a metal surface via the magnets unit.

DO NOT mount to electrical equipment.

• Hang from a nail (or like item) by opening the Nail Hook 12 and placing the Nail Hook over the head of the nail.

on the back of the

CHARGING DEVICES:

NOTE: For best results, use cable provided with your device.

1. Connect the cable to your device.

2. Connect the charging cable to the USB A Charge Out Port

Charge In/Out Port device being charged should provide indication that charging has begun.

1. Press and hold the Power button speaker; your device will begin charging.

2. Press and hold the Power button functions will power off; your device will stop charging.

3. When AEPJS3 is in Charge-Out-Only mode, it will automatically shut down once charging is complete and current is no longer being drawn by the device.

Repeat these steps to charge another device.

. Your device will automatically begin charging. The

for 3 seconds to turn on the

again for 3 seconds and all

or USB C

COMPLIANCE

FCC & IC COMPLIANCE

This device complies with part 15 of the FCC RULES and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.

NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

FCC RF EXPOSURE STATEMENTS:

This transmitter must not be co‐located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body or nearby persons.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

IC NOTICE TO CANADIAN USERS

This device complies with industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 5 mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.

IFETEL REPORT

For use in Mexico, the operation of this equipment is subject to the following two conditions: (1) This equipment or device does not cause harmful interference and (2) this equipment or device accepts any interference, including that which can cause undesired operation.

Find Quality Products Online at: sales@GlobalTestSupply.com

www.GlobalTestSupply.com

Klein Tools AEPJS3 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual