with this symbol
carr y electrica l current of
sucient magnitude to
constitute risk of electric
shock. Use only high-quality
professional speaker cables
with ¼" TS or twi st-locking
plugs pre -installed. A llother
installation or modication
should be performed only by
qualiedpersonnel.
This symbol,
wherever it
appears , alerts you to th e
presence of uninsulated
dangerous voltage inside the
enclosure - voltage that may
be sucie nt to constitute a
risk ofshoc k.
This symbol,
wherever it
appears, alerts you to
important operating and
maintenance instructions in
the accompanying literature.
Please read themanual.
Caution
To reduce the
risk of ele ctric shock , do
not remove th e top cover
(or the rear sec tion). No
user serviceable part s
inside. Refer servicing to
qualiedpersonnel.
Caution
To reduce the risk
of re or ele ctric shock , do not
expose t his appliance to rai n
and moist ure. Theapparatu s
shall not be e xposed to
dripping or splashing liquids
and no objec ts lled with
liquids, such as vases, shall be
placed on the apparatus.
Caution
These service
instru ctions are for u se by
qualied service personnel
only. Toreduce the r isk of
electric shock do not perform
any servicing other than that
contained in the operation
instructions. Repairshave to
be perf ormed by qualie d
servicepersonnel.
1. Read these instructions.
2. Keep these inst ructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this
apparatus near water.
6. Clean only with
dry clo th.
7. Do not bloc k any
ventilation openings. Install
in accordan ce with the
manufacturer’s instruct ions.
8. Do not install n ear any
heat sourc es such as radiator s,
heat regis ters, stoves, or
other apparatus (including
ampliers) that produce heat.
9. Do not defeat t he safety
purpos e of the polarized
or grounding-type plug.
A polarize d plug has two
blades with one wider than
the other. A grounding-type
plug has t wo blades and a
third grounding prong. The
wide blade or the third prong
are provid ed for your safe ty.
Ifthe prov ided plug does not
t into your o utlet, consult an
electrician for replacement of
the obsolete outlet.
10. Protec t the power cord
from bei ng walked on or
pinched particularly at plugs,
convenience receptacles, and
the point w here they exit
from the apparatus.
11. Use only attachments /
accessories specied by
themanufacturer.
12. Use
only with t he
cart, stand,
tripod,
bracket, or
table spe cied by the
manufac turer, or sold with
the appar atus. When a car t is
used, use caution when
moving the cart/apparatus
combination to avoid injury
from tip-over.
13. Unplug this app aratus
during lightning storms or
when unused for long periods
of time.
14. Ref er all servicing to
qualied service personnel.
Servicing is required when
the apparatus has been
damaged in a ny way, such
as power sup ply cord or
plug is damaged, liquid has
been spill ed or object s have
fallen int o the apparatus, t he
apparatus has been exposed
to rain or moi sture, does
not operate normally, or has
beendrop ped.
15. The appar atus shall be
connec ted to a MAINS socket
outlet with a protective
earthing connection.
16. Where the MAINS plug
or an applian ce coupler is
used as the disconnect device,
the disconnect device shall
remain readily operable.
17. Correct
disposal of
this product:
This symbol
indicates
that this
product must not be disposed
of with household waste,
accordin g to the WEEE
Directive (2012/19/EU) and
your national law. This
produc t should be taken to a
collection center license d for
the recycling of waste
electrical and elec tronic
equipment (EEE). The
mishandling of this type of
waste cou ld have a possible
negative i mpact on the
environment and human
health due to potentially
hazardous substances that
are generally associated with
EEE. At the sam e time, your
coopera tion in the correc t
disposal of this product will
contribute to the ecient use
of natural resources. For more
information about where you
can take you r waste
equipment for recycling,
please con tact your loca l city
oce, or your household
waste coll ection ser vice.
18. Do not i nstall in a
conned sp ace, such as a
book cas e or similar unit.
19. Do not plac e naked
ame sourc es, such as lighted
candles, on the apparatus.
20. Please k eep the
environmental aspects of
battery disposal in mind.
Batter ies must be disp osed-of
at a battery collection point.
21. This apparatus may be
used in tr opical and moder ate
climates u p to 45°C.
LEGAL DISCLAIMER
Music Tribe acce pts no
liability for any loss
which may be s uered
by any pers on who relies
either wh olly or in part
upon any description,
photograph, or statement
contained herein.
Technical specications,
appearances and other
information are subject
to change wi thout notice.
All tradem arks are the
property of their respective
owners. Midas, Klark Teknik,
Lab Grup pen, Lake, Tannoy,
Turbosound, TC Electronic,
TC Helicon, Behringer,
Bugera, Oberheim, Auratone,
Aston Microphones and
For the applicable warranty
terms and co nditions and
additional information
regarding Music Tribe’s
Limited Warranty, please see
complete details online at
musictribe.com/warranty.
Instrucciones de
seguridad
Las terminales
marcadas con este
símbolo transportan corriente
eléctrica de magnitud
suciente como para
constituir un riesgo de
descarga eléctric a. Utilicesolo
cables de altavoz
profesionales y de alta calidad
con conec tores TS de 6,3 mm
o de bayoneta prejados.
Cualquier otra instalación o
modicación debe ser
realizada únicamente por un
técnicoc ualicado.
Este símbolo,
siempre que
aparece, lea dvierte de la
45Quick Start GuideVNET USB RS232 INTERFACE
presencia de voltaje peligroso
sin aislar de ntro de la caja;
estevolt aje puede ser
suciente para constituir un
riesgo d edescarga.
Este símbolo,
siempre que
aparece, lea dvierte sobr e
instrucciones operativas y de
mantenimiento que aparecen
en la documentación adjunta.
Por favor, leaelmanu al.
Atención
Para reducir el
riesgo d e descarga eléc trica,
no quite la ta pa (olaparte
poster ior). Nohay piezas en
el interior del equipo que
puedan ser reparadas por
el usuario. S ies necesario,
póngase en contacto con
personal cualicado.
Atención
Para reducir el
riesgo d e incendio o desca rga
eléct rica, no expong a este
aparato a la lluvia, humedad
o alguna otr a fuente que
pueda salpicar o derramar
algún líquido sobre el
aparato. Noc oloque ningún
tipo de recipiente para
líquidos s obre elaparato.
Atención
Las instrucciones
de servicio deben llevarlas
a cabo exclusivamente
personal cualicado.
Paraevit ar el riesgo de
una descarga eléctric a, no
realice reparaciones que no
se encuentren descritas en
el manual de operaciones.
Lasreparaciones deben ser
realizadas exclusivamente
por pers onalcualicad o.
1. Lea las instrucciones.
2. Conserve estas
instrucciones.
3. Preste atenció n a todas
las advertencias.
4. Siga todas las
instrucciones.
5. No use este apara to
cerca del agua.
6. Limpie este apar ato con
un paño sec o.
7. No bloquee las
aberturas de ventilación.
Instale el equipo de acuerdo
con las instrucciones del
fabricante.
8. No instale este equipo
cerca de f uentes de calor
tales como radiadores,
acumuladores de calor,
estuf as u otros aparato s
(incluyendo amplicadores)
que puedan producir calor.
9. No elimine o deshabilite
nunca la con exión a tierra
del aparat o o del cable de
alimentación de corriente.
Unenchuf e polarizado tie ne
dos polos , uno de los cuales
tiene un con tacto más ancho
que el otro. Un a clavija con
puesta a tierra dispone de
tres cont actos: dos polo s y la
puesta a t ierra. El contac to
ancho y el ter cer contacto,
respectivamente, son los
que garantizan una mayor
seguridad. Si el enchufe
suministrado con el equipo
no concuer da con la toma de
corriente, consulte con un
electricista par a cambiar la
toma de corr iente obsolet a.
10. Coloque el cable de
suministro de energía de
manera que n o pueda ser
pisado y que esté protegido
de objetos alados.
Asegúr ese de que el cable d e
suministro de energía esté
protegido, especialmente en
la zona de la clav ija y en el
punto dond e sale del aparato.
11. Use únicamente los
dispositivos o accesorios
especicados por el
fabricante.
12. Use
únicamente
la carretilla,
plataforma,
trípode,
soporte o mesa especicados
por el fab ricante o
suministrados junto con el
equipo. Al t ransportar e l
equipo, tenga cuidado para
evitar daños y caídas al
tropez ar con algún obstá culo.
13. Desenchufe el equipo
durante to rmentas o si no
va a utilizarlo durante un
periodo l argo.
14. Confíe las reparaciones
únicamente a servicios
técnicos cualicados.
La unidad requiere
mantenimiento siempre que
haya sufrido algún daño,
si el cable de suministro
de energía o e l enchufe
presentaran daños,
sehubier a derramado un
líquido o hubieran caído
objetos dentro del equipo,
si el aparat o hubiera estad o
expues to a la humedad o
la lluvia, si ha d ejado de
funcionar de manera normal
o si ha sufr ido algún golpe
o caída.
15. Al c onectar la unid ad a
la toma de cor riente eléct rica
asegúrese de que la conexión
disponga de una unión
atierra.
16. Si el enchu fe o conector
de red sir ve como único
medio de desconexión, éste
debe ser acc esiblefácilme nte.
17. Cómo
debe
deshacerse
de este
aparato: Este
símbolo
indica qu e este aparato no
debe ser tratado como basura
orgánica, según lo indicado
en la Direc tiva WEEE
(2012/19/EU) y a las
normativas aplicables en su
país. En lug ar de ello deberá
llevarlo al punto limpio más
cercano p ara el reciclaje de
sus elemen tos eléctric os/
electrónicos (EEE). Al hacer
esto es tará ayudando a
prevenir las posibles
consecuencias negativas para
el medio amb iente y la salud
que podrí an ser provocada s
por una gestión inadecuada
de este tip o de aparatos.
Además, el reciclaje de
materiales ayudará a
conservar los recursos
naturales. Para más
información acerca del
reciclaje de este aparato,
póngase e n contacto con el
Ayuntamiento de su ciudad o
con el punto limpio local.
18. No instale esta unidad
en un espac io muy reducido,
tal como enc astrada en una
librería o s imilar.
19. No coloque objetos
con llama, com o una vela
encendida, sobre este
aparato.
20. Tenga presentes todas
las advertencias relativas
al recicl aje y correcta
eliminación de las pilas.
Las pilas deben ser siempre
eliminadas en un punto
limpio y nunc a con el resto de
la basura orgánica.
21. Puede usar este
aparato en lugares con climas
tropicales y moderados que
soporten temperaturas de
hasta 45 °C.
NEGACIÓN LEGAL
Music Tribe no admite ningún
tipo de responsabilidad por
cualquier daño o pérdida
que pudiera sufrir cualquier
person a por conar total
o parcialm ente en la
descripciones, fotografías
o armaciones contenidas
en este doc umento.
Las especicaciones
Si quiere con ocer los detalle s
y condiciones aplicables
de la garant ía así como
información adicional sobre
la Garantía limitada de
Music Tribe, consulte online
toda la info rmación en la web
musictribe.com/warranty.
67Quick Start GuideVNET USB RS232 INTERFACE
Consignes de sécurité
Les points repérés
par ce symb ole
portent une tension
électrique susante pour
constituer un risque
d’électrocution. Utilisez
uniquement des câbles
d’enceintes professionnels de
haute quali té avec ches Jack
mono 6,35 mm ou c hes à
verrouillages déjà installées.
Touteautre ins tallation ou
modication doit être
eectuée uniquement par un
personnel qualié.
Ce symbol e avertit
de la prése nce
d’une tension dangereuse et
non isolée à l’intérieur de
l’appareil - elle peut
provoquer des chocs
électriques.
Attention
Ce symbol s ignale
les consignes d’utilisation et
d’entre ! Tienimportantes
dans la documentation
fournie. Lisez les consignes
de sécur ité du manuel
d’utilisation del’appareil.
Attention
Pour éviter t out
risque de choc électrique,
ne pas ouv rir le capot de
l’appareil ni démonter
le panneau ar rière.
L’intérieur de l’appareil ne
possède aucun élément
réparable par l’utilisateur.
Laissert oute réparatio n à un
profes sionnelqualié.
Attention
Pour rédui re les
risques d e feu et de choc
électrique, n’exposez pas
cet appar eil à la pluie, à la
moisissu re, auxgouttes o u
aux éclaboussures. Ne posez
pas de récipient contenant un
liquide sur l’appareil (unvase
par exemple).
Attention
Ces consignes de
sécurité et d’entretien sont
destinées à un personnel
qualié. Pou r éviter tout
risque de choc électrique,
n’eectuez aucune
réparation sur l’appareil qui
ne soit déc rite par le manuel
d’utilisation. Les éventuelles
réparations doivent être
eectuées uniquement par
un technic ienspécialisé.
1. Lisez ces consignes.
2. Conservez ces
consignes.
3. Respectez tous les
avertissements.
4. Respectez toutes les
consignes d’utilisation.
5. N’utilisez jamais
l’appareil à p roximité d’un
liquide.
6. Nettoyez l’appareil avec
un chion sec.
7. Veillez à ne pas
empêcher la bonne
ventilation de l’appareil via
ses ouïe s de ventilation.
Respectezles consignes
du fabricant concernant
l’installation del’appareil.
8. Ne placez pas l’appareil
à proximit é d’une source de
chaleur telle qu’un chauage,
une cuisinière ou tout
appareil dégageant de la
chaleur (y c ompris un ampli
depuissa nce).
9. Ne supprime z jamais la
sécurité des prises bipolaires
ou des pris es terre. Les
prises bipolaires possèdent
deux contacts de largeur
diéren te. Leplus large est
le contac t de sécurité. Le s
prises terre possèdent deux
contac ts plus une mise à la
terre ser vant de sécur ité. Si la
prise du bloc d’alimentation
ou du cordon d ’ali-mentation
fourni ne c orrespond pas à
celles de votre installation
élect rique, faites ap pel à un
électricien pour eectuer le
changeme nt de prise.
10. Installez le cordon
d’alimentation de telle
façon que personne ne
puisse marcher dessus et
qu’il soi t protégé d’arêtes
coupantes. Assurez-vous
que le cordon d’alimentation
est suffisamment protégé,
notamment au niveau de
sa prise é lectrique e t de
l’endroit où il e st relié à
l’appareil; cela est également
valable pour une éventuelle
rallonge électrique.
11. Utilisez exclusivement
des accessoires et des
appareils supplémentaires
recommandés par
lefabricant.
12. Utilisez
exclusivement
des chariots,
des diables,
des
présent oirs, despieds e t des
surfaces de travail
recommandés par le fabricant
ou livrés av ec le produit.
Déplacez
précautionneusement tout
chariot o u diable chargé pou r
éviter d’éventuelles blessures
en cas de chu te.
13. Déb ranchez l’appareil
de la tension s ecteur en cas
d’orage ou si l’appareil reste
inutilisé pendant une longue
période de temps.
14. Les travaux d’entretien
de l’apparei l doivent être
eectués uniquement
par du per sonnel qualifié.
Aucunentretien n’est
nécess aire sauf si l’appare il
est endommagé de
quelque f açon que ce soit
(dommagessur le cordon
d’alimentat ion ou la prise par
exemple), siun liq uide ou un
objet a pén étré à l’intérie ur
du châssis , si l’appareil a
été expo sé à la pluie ou à
l’humidité, s’il ne fonctionne
pas corre ctement ou à la sui te
d’une chute.
15. L’appareil doit être
connec té à une prise sec teur
dotée d’une protection par
mise à la terr e.
16. La prise électrique ou
la prise IEC d e tout appareil
dénué de bouton marche/
arrêt doi t rester accessi ble
enperman ence.
17. Mise
au rebut
appropriée
de ce
produit:
Ce symbole
indique qu ’en accord ave c la
direc tive DEEE (2012/19/EU)
et les lois en vigueur dans
votre pays , ce produit ne doit
pas être jeté avec les déchets
ménager s. Ce produit doit
être dép osé dans un point de
collecte agréé pour le
recyclage des déchets
d’équipements électriques et
électroniques (EEE).
Une mauvaise manipulation
de ce typ e de déchets
pourrait avoir un impact
négatif sur l’environnement
et la santé à c ause des
substances potentiellement
dangereuses généralement
associées à ces équipements.
En même temps,
votre coopération dans la
mise au rebu t de ce produit
contribuera à l’utilisation
ecace des ressources
naturelles. Pour plus
d’informations sur l’endroit
où vous pou vez déposer vos
déchets d’équipements pour
le recyclage,
veuillez contacter votre
mairie ou vo tre centre local
de collecte des déchets.
18. N’installez pas l’appareil
dans un espa ce conné tel
qu’une bibliothèque ou
meuble similaire.
19. Ne placez jamais
d’objets en ammés, tels que
des bougies allumées, sur
l’appareil.
20. Garde z à l’esprit
l’impact environnemental
lorsqu e vous mettez des
piles au rebus. Les piles usées
doivent êt re déposées dan s
un point de co llecte adapté.
21. Cet appareil peut
être uti lisé sous un climat
tropic al ou modéré avec
des températures de
45°C maximum.
DÉNI LÉGAL
Music Tribe ne p eut être
tenu pour responsable pour
toute per te pouvant êtr e
subie par toute personne
se ant en par tie ou en
totalité à toute description,
photographie ou armation
contenue dans ce document.
Les caractéristiques,
l’apparence et d’autres
informations peuvent faire
l’objet de modications
sans notication. Toutes les
marques appartiennent à
leurs propriétaires respectifs.
Midas, Klark Teknik,
Lab Grup pen, Lake, Tannoy,
Pour connaître les
termes et conditions de
garantie applicables,
ainsi que les informations
supplémentaires et
détaillées sur la Garantie
Limitée de Music Tribe,
consultez le site Internet
musictribe.com/warranty.
Wichtige
Sicherhteitshinweise
Vorsicht
Die mit dem
Symbol markierten
Anschlüsse führen so
viel Spannung, dassdie
Gefahr eines Stromschlags
besteht. Verwenden Sie nur
hochwertige, professionelle
Lautsprecherkabel mit
vorinstallierten 6,35 mm
MONO-Klinkensteckern
oder Lautsprecherstecker
mit Drehverriegelung. Alle
anderen Installationen
oder Modikationen sollten
nur von qualiziertem
Fachpersonal ausgeführt
werden.
Achtung
Um eine
Gefährdung durch
Stromschlag auszuschließen,
darf die Geräteabdeckung
bzw. Geräterückwandnicht
abgenommen werden.
ImInnern de s Geräts
benden s ich keine vom
Benutzer reparierbaren Teile.
Reparaturarbeiten dürf en nur
von qualiziertem Personal
ausgeführtwerden.
Achtung
Um eine
Gefährdung durch Feuer bzw.
Stromschlag auszuschließen,
darf dieses Gerät weder
Regen oder Feuchtigkeit
ausgesetzt werden noch
sollten Spritzwasser oder
tropfende Flüssigkeiten
in das Gerät gelangen
können. Stellen Sie keine
mit Flüssigkeit gefüllten
Gegens tände, wie z. B. Vasen,
aufdasGer ät.
Achtung
Die ServiceHinweise sind nur durch
qualiziertes Personal
zu befol gen. Umeine
Gefährdung durch
Stromschlag zu vermeiden,
führen Sie bitte keinerlei
Reparaturen an dem
Gerät durc h, dienicht in
der Bedienungsanleitung
beschrieben sind.
Reparaturen sind nur
von qualiziertem
Fachpersonaldurchzuführen.
1. Lesen Sie diese
Hinweise.
2. Bewahren Sie diese
Hinweise auf.
3. Beachten Sie alle
Warnhinweise.
4. Befolgen Sie alle
Bedienungshinweise.
5. Betreiben Sie das Gerät
nicht in der N ähe vonWasser.
6. Reinigen Sie das Gerät
mit einem trockenen Tuch.
7. Blockieren Sie nicht die
Belüftungsschlitze. Beachten
Sie beim Einb au des Gerätes
die Herstellerhinweise.
8. Stellen Sie das Gerät
nicht in der N ähe von
Wärmequellen auf. Solche
Wärmequ ellen sind z. B.
Heizkörper, Herde oder
andere Wärme erzeugende
Geräte (auch Verstärker).
9. Entfernen Sie
in keinem Fall die
Sicherheitsvorricht ung von
Zweipol- oder geerdeten
Steckern. Ein Zweipolstecker
hat zwei unterschiedlich
breite Stec kkontakte. Ein
geerde ter Stecker hat zwei
Steckkontakte und einen
dritten Erdungskontakt.
Derbreit ere Steckkontak t
oder der zusätzliche
Erdungskontakt dient
Ihrer Sicherheit. Falls das
mitgelieferte Steckerformat
nicht zu Ihrer Steckdose
passt, we nden Sie sich bit te
an einen Elektriker, damit
die Steckdose entsprechend
ausgetauscht wird.
10. Verlegen Sie das
Netzka bel so, dass es vor
Tritten und scharfen Kanten
geschützt ist und nicht
beschädigt werden kann.
Achten Sie bitte insbesondere
im Bereich der Stecker,
Verlängerungskabel und
an der Stelle, an d er das
Netzkabel das Gerät verlässt,
aufausrei chendenSchut z.
11. Das Ge rät muss
jederzeit mit intaktem
Schutzleiter an das Stromnetz
angeschlossen sein.
12. So llte der
Hauptnetzstecker oder
eine Gerätesteckdose die
Funktionseinheit zum
Abschalten sein, muss diese
immer zugänglich sein.
13. Verwenden Sie nur
Zusatzgeräte/ Zubehörteile,
dielaut Hersteller geeignet
sind.
14.
Verwenden
Sie nur
Wagen,
Standvorrich-tungen, Stative,
Halter ode r Tische, die vom
Hersteller benannt oder im
Lieferumfang des Geräts
enthalten sind. Falls Sie einen
Wagen benutzen, seien Sie
vorsichtig beim Bewegen der
Wagen- Gerätkombination,
umVerletzungen durch
Stolpern z uvermeiden.
15. Ziehen Sie den
Netzstecker bei Gewitter oder
wenn Sie das Gerät längere
Zeit nicht benutzen.
16. Lasse n Sie alle
Wartungsarbeiten nur von
qualiziertem ServicePersonal ausführen.
EineWartung ist notwendig,
wenn das Gerät in irgendeiner
Weise beschädigt wurde
(z. B. Beschädigung des
Netzkabels oder Steckers),
Gegenstände oder Flüssigkeit
in das Geräteinnere gelangt
sind, das Ger ät Regen oder
Feuchtigkeit ausgesetzt
wurde, das G erät nicht
ordnungsgemäß funktioniert
oder auf de n Boden
gefallen ist.
17.
Korrekte
Entsorgung
dieses
Produkts:
Dieses
Symbol weis t darauf hin, das
Produkt entsprechend der
WEEE Direk tive (2012/19/EU)
und der jeweiligen nationalen
Gesetze nicht zusammen mit
Ihren Haushaltsabfällen zu
entsorgen. DiesesProdukt
sollte bei einer autorisierten
Sammelstelle für Rec ycling
elektrischer und
elektronischer Geräte (EEE)
abgegeben werden. Wegen
bedenklicher Substanzen,
diegenerell mit elektrischen
und elektronischen Geräten
in Verbindung stehen, könnte
eine unsachgemäße
Behandlung dieser Abfallart
eine negative Auswirkung auf
Umwelt und Gesundheit
haben. Gleichzeitig
gewährleistet Ihr Beitrag zur
richtigen Entsorgung dieses
Produkts die eektive
Nutzung natürlicher
Ressour cen. Fürweitere
Informationen zur
Entsorgung Ihrer Geräte bei
einer Recycling-Stelle
nehmen Sie bitte Kontakt
zum zuständigen städtischen
Büro, Entsorgungsamt oder
zu Ihrem
Haushaltsabfallent sorgerauf.
18. Installieren Sie das
Gerät nicht in einer beengten
Umgebung, zum Beispiel
Bücherregal oder ähnliches.
19. Stellen Sie keine
Gegenstände mit oenen
Flammen, etwa brennende
Kerzen, auf d as Gerät.
20. Beach ten Sie bei der
Entsorgung von Batterien
den Umweltschutz-Aspekt.
Batterien müssen bei einer
Batterie-Sammels telle
entsorgt werden.
21. Dieses G erät ist in
tropischen und gemäßigten
Klimazon en bis 45° C
einsetzbar.
Die geltenden
Garantiebedingungen und
zusätzliche Informationen
bezüglich der von
Music Tribe gewährten
beschränkten Garantie
nden Sie online unter
musictribe.com/warranty.
Instruções de
Segurança Importantes
Aviso!
Terminais
marcados com o símbolo
carregam corrente elétrica
de magnitude suciente
para cons tituir um risco d e
choque elétrico. Use apenas
cabos de al to-falantes de a lta
qualidade com plugues TS
de ¼" ou plugues co m trava
de torção pré-instalados.
Todas as outras instalações
e modicações devem
ser efet uadas por
pessoasqualicadas.
Este símbolo, onde
quer que o
encontre, alerta-o para a
leitura das instruções de
manuseamento que
acompanham o
equipam ento. Por favor leia o
manual deinstruções.
Atenção
De forma a
diminuir o risco de choque
eléct rico, nãoremover a
cober tura (ouasecção de
trás). Não existem peças
substi tuíveis por par te do
utilizador no seu interior.
Para esse e feito recorre r a um
técnicoqu alicado.
Atenção
Para redu zir o risco
de incêndios ou choques
eléctricos o aparelho não
deve ser ex posto à chuva nem
à humidade. Al émdisso, não
deve ser sujeito a salpicos,
nem devem ser colocados
em cima do aparelho
objectos contendo líquidos,
taiscomoja rras.
Atenção
Estas instruções
de operaç ão devem ser
utiliza das, emexclusivo,
por técnicos de assistência
qualicados. Para evitar
choques eléctricos não
proceda a reparações ou
intervenções, que não as
indicadas nas instruções de
operaç ão, salvo se possuir a s
quali-cações necessár ias.
Para evitar choques
eléct ricos não proced a a
reparações ou intervenções,
que não as indicadas nas
instru ções de operaçã o. Só
o deverá fa zer se possuir as
qualicaçõesnecessárias.
1. Leia esta s instruções .
2. Guarde estas
instruções.
3. Preste atenção a todos
os avisos.
4. Siga todas as instr uções.
5. Não utilize este
disposit ivo perto de água .
6. Limpe apenas com um
pano seco.
7. Não obstrua as entradas
de ventilação. Instale de
acordo com a s instruções do
fabricante.
8. Não instale perto de
quaisquer fontes de calor
tais como radiadores, bocas
de ar quente, f ogões de
sala ou out ros aparelhos
(incluindo amplicadores)
que produzam calor.
9. Não anule o objec tivo
de segurança das chas
polariz adas ou do tipo de
ligação à te rra. Uma cha
polarizada dispõe de duas
palhetas sendo uma mais
larga do que a o utra. Uma
cha do tip o ligação à terra
dispõe de duas palhetas e
um terceiro d ente de ligação
à terra. A pa lheta larga ou o
terceiro dente são fornecidos
para sua se gurança. Se a
cha fornecida não encaixar
na sua tomada, consulte
um electricista para a
substituição da tomada
obsoleta.
10. Proteja o ca bo de
alimentação de pisadelas
ou apertos, especialmente
nas chas, e xtensões, e no
local de s aída da unidade.
Certi que-se de que o ca bo
eléct rico está prote gido.
Verique particularmente
nas chas, nos receptáculos
e no ponto em qu e o cabo sai
doaparelh o.
11. O apar elho tem de estar
sempre conectado à rede
eléct rica com o conduto r de
protecç ão intacto.
12. S e utilizar uma ch a
de rede pr incipal ou uma
tomada de aparelhos para
desligar a unidade de
funcionamento, esta deve
estar sempre acessível.
13. Uti lize apenas ligações/
acessórios especicados
pelofabr icante.
14. Utilize
apenas com
o carrinho,
estrutura,
tripé,
suporte, ou mesa
especicados pelo fabricante
ou vendidos com o
dispositivo. Quandoutilizar
um carrinho, tenha cuidado
ao mover o conju nto carrinho/
dispositivo para evitar danos
provoca dos pela terpidaç ão.
15. De sligue este
dispositivo durante as
trovoadas ou quando não
for utilizado durante longos
período s detempo.
16. Qualquer tipo de
reparação deve ser sempre
efectuado por pessoal
qualica do. É necessária
uma reparação sempre
que a unidade tiver sido de
alguma forma danicada,
como por exe mplo: no caso
do cabo de alimentação
ou cha se en contrarem
danicados; naeventualidade
de líquido ter sido derramado
ou objec tos terem caído
para dentro do dispositivo;
no caso da un idade ter
estado e xposta à chuv a ou
à humidade; s eesta não
funcionar normalmente, ou
se tiver ca ído.
17.
Correcta
eliminação
deste
produto:
este símbolo
indica qu e o produto não
deve ser eliminado
juntamente com os resíduos
domésticos, segundo a
Direc tiva REEE (2012/19/EU) e
a legislação nacional. Este
produto deverá ser levado
para um cent ro de recolha
licenciado para a reciclagem
de resíduos de equipamentos
eléctricos e electrónicos (EEE).
O tratamento incorrecto
deste tipo de resíduos pode
ter um eventual impacto
negativo n o ambiente e na
saúde humana devido a
substâncias potencialmente
perigosas que estão
geralmente associadas aos
EEE. Ao mesmo te mpo, a sua
colaboração para a
eliminação correcta deste
produto irá contribuir para a
utilização eciente dos
recur sos naturais. Par amais
informação acerca dos locais
onde pode rá deixar o seu
equipamento usado para
recicla gem, é favor contac tar
os serviços municipais locais,
a entidade d e gestão de
resíduo s ou os serviços d e
recolha de
resíduosdomésticos.
1213Quick Start GuideVNE T USB RS232 INTERFACE
18. Não instale em
lugares connados, tais
como estantes ou unidades
similares.
19. Não coloque fontes
de chama, ta is como velas
acesas, s obre o aparelho.
20. Favor, obedec er os
aspectos ambientais de
descar te de bateria. Ba terias
devem ser de scartadas e m
um ponto de co letas de
baterias.
21. Esse apa relho pode ser
usado em cl imas tropicais e
moderados até 45°C.
Para obter o s termos
de garantia aplicáveis e
condições e informações
adicionais a respeito
da garantia limitada
do Music Tribe, f avor
vericar detalhes na
íntegra at ravés do website
musictribe.com/warranty.
Informazioni importanti
Attenzione
I terminali
contrassegnati da questo
simbolo conducono una
corrente elettrica di
magnitudine suciente
a costit uire un rischio di
scossa elettrica. Utilizzare
solo cavi p er altoparlanti
professionali di alta qualità
con jack sbilanciati da
6,35mm. o connet tori con
blocco a rot azione. Tutte
le altre installazioni o
modiche devono essere
eseguite esclusivamente da
personale qualicato.
Attenzione
Questo simbolo,
ovunque appaia,
avver te della presenz a di
una tensione pericolosa
non isolata all'interno
dello chassis, tensione che
può essere suciente per
costit uire un rischio di s cossa
elettrica.
Attenzione
Questo simbolo,
ovunque appaia, segnala
importanti istruzioni
operative e di manutenzione
nella documentazione
allegata . Si invita a leggere i l
manuale.
Attenzione
Per ridurr e il
rischio di scosse elettriche,
non rimuovere il coperchio
superiore (o la sezione
posteriore). All'interno
non ci sono parti riparabili
dall'utente. Per l a
manutenzione rivolgersi a
personale qualicato.
Attenzione
Per ridurr e il
rischio d i incendi o scosse
elettriche, non esporre
questo apparecchio a pioggia
e umidità. L'apparecchio
non deve ess ere esposto a
gocciolio o schizzi di liquidi e
nessun oggetto contenente
liquidi, come vasi, deve essere
collocato sull'apparecchio.
Queste istruzioni di
servizio sono
destinate esclusiva mente a
personale qualicato. Per
ridurre il rischio di scosse
elettriche non eseguire
interventi di manutenzione
diversi d a quelli contenuti ne l
manuale di istruzioni. Le
riparazioni devono essere
esegui te da personale di
assistenza qualicato.
1. Leggere queste
istruzioni.
2. Conservare queste
istruzioni.
3. Prestare attenzione a
tutti gli avvisi.
4. Applicare tutte le
istruzioni.
5. Non utilizzare questo
dispositivo vicino l'acqua.
6. Pulire esclusivamente
con un panno a sciutto.
7. Non bloccare le
aperture di ventilazione.
Installa re in conformit à con le
istruz ioni del produt tore.
8. Non installare vicino
a fonti di c alore come
radiatori, termoregolatori,
stufe o al tri apparecch i
(inclusi am plicatori) che
producono calore.
9. Non esclude re la
sicurezza fornita dalla spina
polariz zata o con mess a a
terra. Una spina polarizzata
ha due lame, una più larga
dell'altra. Una spina con
messa a ter ra ha due lame
e un terzo po lo di messa a
terra. L a lama larga o il terzo
polo sono f orniti per la vos tra
sicurez za. Se la spina for nita
non si adat ta alla presa,
consultare un elettricista per
la sosti tuzione della pre sa
obsoleta.
10. Protegge re il cavo di
alimentazione dal calpestio
o essere s chiacciato in
particolare alle spine, prese di
corrente e i l punto in cui esce
dall'apparecchio.
11. Utilizzare
esclusivamente dispositivi/
accessori specicati dal
produttore.
12.
Utilizzare
solo carrelli,
supporti,
treppiedi,
stae o t avoli indicati dal
produt tore o venduti con
l'apparecchio. Utilizzando un
carrello, prestare attenzione
quando si sp osta la
combinazione carrello/
apparecchio per evitare
lesioni dovute al
ribaltamento.
13. collegare ques to
apparecchio durante i
temporal i o se non è utilizz ato
per lunghi periodi di tempo.
14. Pe r tutte le ripar azioni
rivolgersi a personale
qualicato. La manutenzione
è necessaria quando
l'apparecchio è danneggiato
in qualsiasi modo, come
danneggiamento del
cavo di alimentazione o
della spina, versamento
di liquido o oggetti caduti
nell'apparecchio, se
l'apparecchio è stato esposto
a pioggia o umidità, se non
funziona normalmente o è
caduto.
15. L'apparecchio deve
essere co llegato a una pres a
1415Quick Start GuideVNET USB RS232 INTERFACE
ricicla ggio vi invitiamo a
contattare l'ucio comunale
locale o il s ervizio di rac colta
dei riuti domestici.
18. Non installare in uno
spazio ri stretto, come i n una
libreria o i n una strutt ura
simile.
19. Non collo care sul
dispositivo fonti di amme
libere, com e candele accese.
20. Per lo smaltimento
delle batterie, tenere in
considerazione gli aspetti
ambientali. Le batterie
devono essere smaltite in
un punto di ra ccolta delle
batter ie esauste.
21. Questo ap parecchio può
essere us ato in climi tropi cali
e temperati no a 45°C.
DISCLAIMER LEGALE
Music Tribe non s i assume
alcuna responsabilità per
eventuali danni che possono
essere su biti da chiunque
si adi in tu tto o in parte
a qualsiasi descrizione,
fotograa o dichiarazione
contenuta qui. Speciche
tecniche, aspetti e altre
informazioni sono soggette
a modich e senza preav viso.
Tutti i march i sono di
proprietà dei rispettivi
titolari . Midas, Klark Teknik ,
Lab Grup pen, Lake, Tannoy,
Turbosound, TC Electronic,
TC Helicon, Behringer, Bugera,
Oberheim, Auratone, Aston
Microphones e Coolaudio sono
Per i termini e l e condizioni
di garanzia applicabili e le
informazioni aggiuntive
relative alla garanzia limitata
di Music Tribe, consultare
online i dettagli completi su
musictribe.com/warranty.
Belangrijke
veiligheidsvoorschriften
Waarschuwing
Aansluitingen
die gemer kt zijn met het
symbool voeren een zodanig
hoge spann ing dat ze een
risico vormen voor elektrische
schokken. Gebruik uitsluitend
kwalitatief hoogwaardig e,
in de handel verkrijgbare
luidsprekerkabels die
voorzie n zijn van ¼" TS
stekkers. Laat uitsluitend
gekwaliceerd personeel
alle overige installatie- of
modicatiehandelingen
uitvoeren.
Dit symbool
wijst u alt ijd op
belangrijke bedienings - en
onderhoudsvoorschrif ten in
de bijbehorende
documenten. Wij vragen u
dringend de handleiding te
lezen.
Attentie
Verwijder in geen
geval de bovenste afdekking
(van het achte rste gedeelt e)
anders b estaat er gevaar
voor een elektrische schok.
Het appar aat bevat geen te
onderhouden onderdelen.
Reparatiewerkzaamheden
mogen uitsluitend door
gekwaliceerd personeel
uitgevoerd worden.
Attentie
Om het risi co op
brand of elektrische schokken
te beperken, dient u te
voorkomen dat dit apparaat
wordt blootgesteld aan regen
en vocht. Het apparaat mag
niet worden blootgesteld
aan neerdruppelend of
opspattend water en er
mogen gee n met water
gevulde voorwerpen – zoals
een vaas – op h et apparaat
worden gezet.
Attentie
Deze
onderhoudsinstructies
zijn uitsluitend bedoeld
voor gekwaliceerd
onderhoudspersoneel.
Om elektrische
schokken te voorkomen,
mag u geen and ere
onderhoudshandelingen
verrich ten dan in de
bedieningsinstructies
vermeld staan.
Reparatiewerkzaamheden
mogen alleen uitgevoerd
worden door gekwaliceerd
onderhoudspersoneel.
1. Lees deze voorschriften.
2. Bewaar deze
voorschriften.
3. Neem alle
waarschuwingen in acht.
4. Volg alle
voorschriften op.
5. Gebruik dit apparaat
niet in de bu urt van water.
6. Reinig het uitsluitend
met een dro ge doek.
7. Let erop ge en van de
ventilatie-openingen te
bedekken. Plaats en installeer
het volgens de voor- schriften
van de fabr ikant.
8. Het apparaat mag niet
worden gep laatst in de buur t
van radiatoren, warmteuitlaten, kachels of andere
zaken (ook versterkers) die
warmte afgeven.
9. Maak de veiligheid
waarin do or de polarisati eof aardingsstekker wordt
voorzien, niet ongedaan.
Een polarisatiestekker heeft
twee bla den, waarvan er
een bred er is dan het andere.
Een aardingsstekker heeft
twee bla den en een derde
uitsteeksel voor de aarding.
Het bred ere blad of het
derde uitsteeksel zijn er
voor uw veiligheid. Mocht
de geleverde stekker niet in
uw stopco ntact passe n, laat
het conta ct dan door een
elektricien vervangen.
10. Om beschadiging
te voorkom en, moet de
stroomleiding zo gelegd
worden dat e r niet kan
worden over gelopen
en dat ze besc hermd is
tegen scherpe kanten.
Zorg zeker voo r voldoende
bescherming aan de stekkers,
de verlengkabels en het
punt waar he t netsnoer het
apparaat verlaat.
11. Het toestel met
altijd me t een intacte
aarddraad aan het stroomnet
aangesloten zijn.
12. Wanneer de stekker
van het hoofdnetwerk of
een apparaatstopcontac t de
functionele eenheid voor het
uitschakelen is, dient deze
altijd toegankelijk te zijn.
13. Gebr uik uitsluitend
door de producent
gespeci- ceerd toebehoren
c.q. onderdelen.
14.
Gebruik
het apparaat
uitsluitend in
combinatie
met de
wagen, het s tatief, de
driepoot, de beugel of tafel
die door de producent is
aangegeven, of die in
combinatie met het apparaat
wordt verkocht. Bij gebruik
van een wagen dient men
voorzic htig te zijn bij het
verrijden van de combinatie
wagen/apparaat en letsel
door valle n te voorkomen.
15. Bi j onweer en als u het
apparaat langere tijd niet
gebruikt, haalt u de stekker
uit het stopcontact.
16. Laat alle voorkomende
reparaties door vakkundig en
bevoegd personeel uitvoeren.
Reparatiewerk-zaamheden
zijn nodig a ls het toestel op
enige wijze beschadigd is
geraakt, bijvoorbeeld als
de hoofd-stroomkabel of
-stekke r is beschadigd, al s
er vloeis tof of voorwerp en
in terech t zijn gekomen, als
het aan regen of vochtigheid
heeft bloot-gestaan, niet
normaal functioneert of
wanneer het is gevallen.
17.
afvoer van
dit product:
dit symbool
geef t aan
dat u dit
produc t op grond van de
AEEA-richtlijn (2012/19/EU)
en de nationale wetgeving
van uw land nie t met het
gewone huishoudelijke afval
mag weggooien. Dit product
moet na ao op van de nuttig e
levensduur naar een ociële
inzamelpost voor afgedankte
elektrische en elektronische
apparatuur (AEEA) worden
gebracht, zodat het kan
worden gerecycleerd.
Vanwege de potentieel
gevaarlijke stoen die in
Correcte
1617Quick Start GuideVNET USB RS232 INTERFACE
elektrische en elektronische
apparatuur kunnen
voorkome n, kan een onjuiste
afvoe r van afval van het
onderhavige type een
negatiev e invloed op het
milieu en de menselijke
gezondheid hebben. Een
juiste afvoer van dit product is
echter niet alleen beter voor
het milieu en de gezondheid,
maar draagt tevens bij aan
een doelmatiger gebruik van
de natuurlijke hulpbronnen.
Voor meer informatie over de
plaatse n waar u uw
afgedankte apparatuur kunt
inleveren, kunt u contact
opnemen met uw gemeente
of de plaatselijke
reinigingsdienst.
18. Installeer niet in een
kleine ru imte, zoals een
boekenkast of iets dergelijks.
19. Plaats ge en open
vlammen, zoals brandende
kaarsen, op het apparaat.
20. Houd rekening met
de milieuaspecten van het
afvoeren van batterijen.
Batterijen moeten bij een
inzamelpunt voor batterijen
worden ingeleverd.
21. Dit apparaat kan
worden gebruikt in tropische
en gematigde klimaten
tot 45 ° C.
Voor de toepasselijke
garantievoorwaarden en
aanvullende informatie met
betrekking tot de beperkte
garantie van Music Tribe, zie
de volledige details online op
musictribe.com/warranty.
Viktiga
säkerhetsanvisningar
Varning
Uttag markerade
med symbolen leder elektrisk
ströms tyrka som är t illräckligt
stark f ör att utgöra en r isk
för elch ock. Använd endas t
högkvalitativa, kommersiellt
tillgängliga högtalarkablar
med förhandsinstallerade
¼" TS-kontakter. All annan
installering eller modikation
bör endas t utföras av
kompetent personal.
Den här symbolen
hänvisar till viktiga
punkter om användning och
underhåll i den medfölljande
dokumentationen. Var vänlig
och läs bruksanvisningen.
Försiktighet
Minska risken för
elektriska stötar genom att
aldrig ta av h öljet upptill
på appara ten (eller ta av
baksidan). Inuti apparaten
nns det ing a delar som kan
repareras av användaren.
Endast kvalicerad personal
får genomföra reparationer.
Försiktighet
För att minska
risken fö r brand och
elektriska stötar ska
apparaten skyddas mot regn
och fuk t. Apparaten går i nte
utsät tas för dropp e ller spill
och inga vattenbehållare som
vaser etc . får placeras på de n.
Försiktighet
Serviceinstruktionen
är enbar t avsedd för
kvalicerad servicepersonal.
För att undvika risker
genom elektriska stötar,
genomför inga reparationer
på appara ten, vilka inte är
beskrivna i bruksanvisning en.
Endast kvalicerad
fackpersonal får genomf öra
reparationerna.
1. Läs dessa anvisningar.
2. Spara dessa
anvisningar.
3. Beakta alla varningar.
4. Följ alla anvisningar.
5. Använd inte apparaten i
närheten av vatten.
6. Rengör endast med
torr trasa.
7. Bloc kera inte
ventilationsöppningarna.
Installera enligt tillverkarens
anvisningar.
8. Installera aldrig
intill värmekällor
som vär me- element,
varmluftsintag, spisar eller
annan utr ustning som avger
värme (ink lusive först ärkare).
9. Ändra aldrig en
polariserad eller jordad kontakt.
En polariserad kontakt har två
blad – det ena b redare än det
andra. En jordad kontakt har
två blad o ch ett tredj e jordstif t.
Det breda b ladet eller jor dstiftet
är till för d in säkerhet. Om
den medföljande kontakten
inte pass ar i ditt utt ag, ska du
kontakt a en elektrik er för att få
uttaget bytt.
10. Förlägg elkabeln så,
att det in te är möjligt att
trampa på d en och att den är
skyddad mot skarpa kanter
och inte ka n skadas. Ge i
synnerhet akt på områdena
omkring stickkontakterna,
förlängningskablarna och
på det st älle, där elkabeln
lämnar apparaten, är
tillräckligt skyddade.
11. Appar aten måste alltid
vara ansluten till elnätet med
intakt skyddsledare.
12. Om huv udkontakten,
eller ett apparatuttag,
fungerar som
avstängningsenhet måste
denna alltid vara tillgänglig.
13. Använd endas t
tillkopplingar och tillbehör
som angetts av tillverkaren.
14. Använd
endast med
vagn, stativ,
trefot,
hållare eller
bord som an getts av
tillverkaren, eller som sålts
till-sammans med apparaten.
Om du använd er en vagn, var
försi ktig, när du för yttar
kombinationen
vagn-apparat, för att
förhindra olycksfall genom
snubbling.
15. Dr a ur
anslutningskontakten und
åskväder eller när apparaten
inte ska användas under
någon längre tid.
16. Låt kvalicerad per sonal
utfö ra all service. S erviceär
nödvändig när apparaten har
skadats, t .ex.när en elkabe l
eller kontakt är skadad,
vätskaeller främmande
föremål h ar kommit in i
apparaten, eller när den har
fallit i go lvet.
17. Kassera
produkten
på rätt s ätt:
den här
symbolen
indikerar att
produk ten inte ska kast as i
hushållssoporna, enligtWEEE
direktivet (2012/19/EU)
ochgällande, nationell
lagstiftning. Produkten ska
lämnas till e tt auktoris erat
återvinningsställe för
elektronisk och elektrisk
utrust ning (EEE). Om den här
sorte ns avfall hanter as på fel
sätt ka n miljön, och
människors hälsa, påverkas
negativ t på grund av
potentiella risksubstanser
som ofta associeras med EEE.
Avfallshanteras produk ten
däremot på rätt sätt bidrar
detta t ill att naturen s resurser
används på e tt bra sätt .
Kontakta kommun, ansvarig
förvaltning eller
avfallshanteringsföretag för
mer information om
återvinningscentral där
produk ten kanlämnas.
18. Installera inte i ett
trångt u trymme, t.ex. i e n
bokhylsa eller liknande
enhet.
1819Quick Start GuideVNET USB RS232 INTERFACE
19. Placera in te källor med
öppen eld, t .ex. tända ljus, på
apparaten.
20. Tänk på
miljöaspekterna vid kassering
av batterier. Batterier
måste kas seras på ett
batteriuppsamlingsställe.
21. Denna apparat kan
användas i tropiska och
måttlig a klimat upp till 45 ° C.
För tillämpliga garantivillkor
och ytterligare information
om Music Tribes begränsade
garanti, se fullständig
information online på
musictribe.com/warranty.
Ważne informacje o
bezpieczeństwie
Uwaga
Terminale
oznaczone symbolem
przenoszą w ystarczająco
wysokie napięcie elektryczne,
aby stwo rzyć ryz yko
porażenia prądem. Używaj
wyłącznie wysokiej jakości
fabrycznie prz ygotowanych
kabli z zainstalowanymi
wtyc zkami ¼" TS. Wszyst kie
inne instalacje lub
modykacje powinny być
wykonywane wyłącznie
przez wykwalikowany
personel techniczny.
Ten symbol
informuje o
ważnych
wskazówkach dotyczących
obsługi i konserwacji
urządzenia w dołączonej
dokumentacji. Proszę
przeczytać stosowne
informacje w instrukcji
obsługi.
Uwaga
W celu
wyeliminowania
zagrożenia porażenia
prądem zabrania się
zdejmowania obudowy lub
tylnej ścianki urzą dzenia.
Elementy znajdujące się
we wnętr zu urządzenia ni e
mogą być naprawiane przez
użyt kownika. Napraw y mogą
być wykonywane jedynie
przez wykwalikowany
personel.
Uwaga
W celu
wyeliminowania
zagrożenia porażenia prądem
lub zapalenia się urządzenia
nie wolno w ystawiać go
na dział anie deszczu i
wilgotności oraz dopuszczać
do tego, aby do w nętrza
dosta ła się woda lub inna
ciecz. Nie należy stawiać na
urządzeniu napełnionych
cieczą przedmiotów takich
jak np. wazony l ub szklanki.
Uwaga
Prace
serwi sowe mogą być
wykonywane jedynie przez
wykwalikowany personel.
W celu uniknięcia zagrożenia
porażenia prądem nie
należy wykonywać żadnych
manipulacji, które nie są
opisane w instrukcji obsługi.
Naprawy wykonywane
mogą być jed ynie przez
wykwalikowany personel
techniczny.
1. Proszę przeczytać
poniższe wskazówki.
2. Proszę przechowywać
niniejszą instrukcję.
3. Należy przestrzegać
wszystkich wskazówek
ostrzegawc zych.
4. Należy postępować
zgodnie z instrukcją obsługi.
5. Urządzenia nie wolno
używ ać w pobliżu wody.
6. Urządzenie można
czyścić wy łącznie suchą
szmatk ą.
7. Nie zasłaniać otworów
wentylacyjnych. W czasie
podłączania urządzenia
należy przestr zegać zaleceń
producenta.
8. Nie stawiać urządzenia
w pobliżu ź ródeł ciep ła
takich, jak grzejniki, piece
lub urządzenia produkuj ące
ciepł o (np. wzmacniacze).
9. W żadnym wypadku nie
należy usuwać zabezpiec zeń
z wtyczek dwubiegunowych
oraz wtyczek z uziemieniem.
Wtyczka dwubiegunowa
posiada dw a wtyki
kontakt owe o różnej
szerokości. Wtyczka z
uziemieniem ma dwa wtyki
kontakt owe i trzeci wt yk
uziemienia. Szerszy wtyk
kontaktowy lub dodatkow y
wtyk uziemienia służą do
zapewnienia bezpieczeńst wa
użytkownikowi. Je śli format
wtyczki urz ądzenia nie
odpowiada standardowi
gniazdka, proszę zwrócić
się do elek tryka z proś bą o
wymienienie gniazda.
10. Kabel sieciowy
należy u łożyć tak, aby ni e
był narażo ny na deptanie i
działanie ostrych krawędzi,
co mogłoby doprowadzić do
jego uszkodzenia. Szczególną
uwagę zwrócić należy na
odpowiednią ochronę miejsc w
pobliżu w tyczek i pr zedłużac zy
oraz miejs ce, w którym ka bel
sieciowy przymocowany jest
do urządzenia.
11. Urządzenie musi być
zawsze po dłączone do si eci
sprawnym p rzewodem z
uziemieniem.
12. Jeże li wtyk sieci owy
lub gniazdo s ieciowe w
urządzeniu pełnią funkcję
wyłąc znika, to muszą o ne
być zawsze ł atwo dostępne.
13. Uż ywać wyłącznie
sprzętu dodatkowego
i akcesori ów zgodnie z
zaleceniami producenta.
14. Używać
jedynie
zalecanych
przez
producenta
lub znajduj ących się w
zestawie wózków, stojaków,
staty wów, uchwytów i
stołó w. W przy padku
posługiwania się wózkiem
należy zachować szczególną
ostrożność w trakcie
przewożenia zestawu, aby
uniknąć niebezpieczeństwa
potknięcia się i zranienia.
15. W t rakcie burzy or az na
czas dłuższeg o nieużywania
urządzenia należy wyjąć
wtyczkę z gniazdka
sieciowego.
16. Wykonywanie
wszelkich napraw
należy zlecać jedynie
wykwalikowany m
pracownikom serwisu.
Przeprowadzenie przeglądu
technicznego staje się
konieczne, jeśli urządzenie
zostało uszkodzone w
jakikolwiek sposób (dotyczy
to także k abla sieciowego
lub wtyczki), jeśli do wnętrza
urządz enia dostał y się
przedmioty lub ciecz, jeśli
urządzenie wystawione było
na dział anie deszczu lu b
wilgoci, jeśli urządzenie nie
funkcjonuje poprawnie oraz
kiedy spadło na podłogę
17.
Prawidłowa
utylizacja
produktu:
Ten symbol
wskazuje, że
tego produktu nie należy
wyrz ucać razem ze zw ykłymi
odpadami domowymi, tylko
zgodnie z dy rektyw ą w
sprawie zużytego sprzętu
elektrycznego i
elektronicznego (WEEE)
(2012/19/EU) oraz przepisami
krajowymi. Niniejszy produk t
należy przekazać do
autoryzowanego punktu
zbiórki zużytego sprzętu
elektrycznego i
elektronicznego. Niewłaściwe
postęp owanie z tego typ u
odpadami może wywołać
2021Quick Start GuideVNET USB RS232 INT ERFACE
szkodliwe działanie na
środowisko naturalnej i
zdrowie człowieka z powodu
potencjalnych substancji
niebezpiecznych zaliczanych
jako zuży ty sprzęt e lektryc zny
i elektroniczny. Jednocześnie,
Twój wkład w praw idłową
utylizację niniejszego
produk tu przycz ynia się do
oszczędnego
wykorzystywania zasobów
naturalnych. Szczegółowych
informacji o miejscach, w
których można oddawać
zuży ty sprzęt do re cyklingu,
udzielają urzędy miejskie,
przedsiębiorstwa utylizacji
odpadów lub najbliższ y
zakład utylizacji odpadów.
18. Nie instaluj w
ograniczonej przestrzeni,
takiej jak p ółka na ksią żki lub
podobny zes taw.
19. Nie staw iaj na
urządzeniu źródeł
otwartego ognia, takich jak
zapalon e świece.
20. Należy pamiętać o
środowiskowych aspektach
utylizacji bater ii. Baterie
należy u tylizować w punkc ie
zbiórki baterii.
21. To urządzenie może
być uży wane w klimacie
tropikalnym i umiarkowanym
do 45 ° C.
Aby zapozn ać się z
obowiązującymi warunkami
gwarancji i dodatkowymi
informacjami dotycząc ymi
ograniczonej gwarancji
Music Tribe, za poznaj się ze
wszystkimi szcze gółami w
trybie online pod adresem
musictribe.com/warranty.
Important Safety Information
Please rea d carefully and ke ep the following ins tructions an d safety infor mation. Heed all
warnings and follow all instructions.
• • D o not remove covers. T here are no user-ser viceable par ts inside; please re fer servici ng to
qualied s ervice pers onnel.
• • O nly use attach ments/accessor ies specied by th e manufacture r.
• • S ervicing is re quired when the app aratus has been dam aged in any way, such as liqui d has
been spill ed or objects ha ve fallen into the appa ratus, the appara tus has been expo sed to
rain or mois ture, does not ope rate normally, or has be en dropped.
Quick Start
• • I nstall the driver s
• • C onnect compute r via USB or RS232
• • A pply power if using R S232
• • C onnect devices v ia RJ45 cables
Thank You
Thank you fo r choosing this pro duct for your app lication. Please s pare a little tim e to study the
contents o f this guide, so that you o btain the best po ssible perfo rmance from this u nit.
Unpacking
After un packing the unit p lease check care fully for damage. I f damage is found, plea se notify
the carr ier concerned at on ce. You, the consi gnee, must insti gate any claim. Please r etain all
packagi ng in case of futur e re-shipment.
2223Quick Start GuideVNET USB RS232 INTERFACE
Introduction / Key Features
This prod uct gives your Per sonal Computer conn ectivity t o a network of VNET ™ equipped
devices s o they can be control led and monitored . The VNET™ Inter face can connec t via
USB or Serial (R S232).
VNET™ is a f ast network ing topology usin g standard Cat5 c abling to interconn ect compatibl e
devices us ing a simple cablin g scheme. The total sp an of the network m ay be at least 1 km
without repeaters. There is no maximum length for a single span within this limit.
Housed in a c onvenient, rugge d steel case, it can b e used free-s tanding or, using the ra ckmount kit , may be racked along wi th up to two additio nal accessory pr oducts in 1U rack-sp ace.
Features:
• • Rugged steel enclosure
• • Free -standing or rack-mount options
• • Rugged Ethercon network connector s
• • S elf-powered (using USB)
• • C apable of drivin g 1km of net work cable
• • N o special cables
Computer System Requirements
Minimum requirements:
• • P C with Pentium proc essor
• • 32-b it Windows tm oper ating system (NT, 2000, XP, Vista)
• • C D-ROM drive or Inte rnet access
• • R S232 or USB port*
*Note that th e network will op erate slightly mor e quickly when usin g RS232, so this is the
preferred method of connection.
Installing the Software
If you only wa nt to use the VNET™ In terface with th e Serial (RS232) port of y our computer,
you do not nee d to install any driv ers. If you wish to use USB, t hen you need to inst all USB
drivers for this product.
When you plu g the USB connectio n of the VNET™ Inter face into a comput er for the rst tim e,
the compu ter will say “Found new h ardware”, and will prompt yo u to install driver s for it.
Two drivers wi ll be installed: On e for the USB port it self, and one for the Vi rtual Com Port ( VCP).
Note that bo th of these driver s may report that t hey have “Not passed W indows Logo Testing”.
You should sele ct “Continue Any way”.
If the driv er software h as been supplied to yo u on a CD-ROM, place th is in your CD-ROM dri ve.
Alternat ively, download the dr ivers from your ven dor’s web site.
Windows XP Driver Installation
Please pro ceed with the fol lowing steps to ins tall the driver:
1. Conn ect a USB cable fr om your computer (or USB hub) to the USB p ort of the Inter face.
2. The connection brings up “Found New Hardware Wizard”.
3. Click “Ne xt”.
4. Selec t “Search for the b est driver for my de vice”, and click “Next”.
5. Selec t “Specify a location” and click “Next”. In the “Copy M anufacturer 's le from”,
type “D:” w here “D:” is the locat ion of your CD-ROM (or br owse to where you have co pied
the drive rs if you have download ed them from a web sit e).
6. Windows d river le searche s for the device “USB VNE T™ Interface ”.
7. Click “Nex t” to continue.
8. Windows h as nished instal ling the soft ware. Click “Finish” to comple te the rst par t
of installation.
9. Th e “Found New Hardware Wizard” appears a gain, and will comple te the installatio n for the
device “USB VN ET™ Port”.
10. Repeat step (4) to (8) to complete in stallation.
2425Quick Start GuideVNET USB RS232 INTERFACE
Diagram 1
Com Port
The PodWare ap plication uses a COM p ort to communic ate with the connec ted devices.
When you use t he RS232 connecti on from your compu ter to the VNET™ Inte rface, the COM por t
will be the o ne which your comput er normally uses fo r the Serial (RS232) por t; usually COM1.
When you use US B to connect from y our computer to the VNE T™ Interfac e, the Driver sof tware
causes a “ Virtual COM Por t” (VCP) to be create d. This will appear to Po dWare as just another
COM port, a nd can be select ed using Networ k > Com Port. To nd out the COM po rt which
the VNET ™ Interface is usi ng, select Star t > Control Panel > Syst em > Hardware > Device
Manager > Por ts. Here, you shou ld see an entry in th e tree for an item ca lled “USB VNET™ Por t.
Against th is will be the COM port n umber (e.g. COM5).
If you wish to c hange this to a diere nt COM port number, righ t-click on the exis ting COM
port tr ee node, select P roperties > Por t Settings > Ad vanced. There, you wi ll see a COM port
selec tor. Do not change it to a COM por t which is already i n use.
External Power Supply
Provisio n is made to power the unit f rom an externa l VNET™ Accessor y Power Supply.
An exter nal supply is requ ired in either of the se two circums tances:
• • I f it is desired to use an R S232 (serial) connec tion to the PC
• • I f there are VNET™ n etwork cable po wered devices any where on the net work
If USB is being u sed and there are no su ch VNET™ cable po wered devices, no ex ternal supply
is requir ed and the interf ace will be powered f rom the computer ’s USB port.
Connecting a Computer
You can connec t your computer to th e VNET Interface in on e of two ways:
RS232
If your comp uter has a native Seri al (RS-232) port, just con nect this to the RS2 32 socket on the
VNET™ In terface using an R S-232 extension cab le (a straight-throug h female-to-mal e), as in
diagram 1. When u sing RS232, it is necess ary to supply DC p ower to the VNET™ Inte rface from
the compan ion Accessory Powe r Supply produc t via the 3.5 mm jack cabl e provided with th e
power supp ly. This can power either o ne or two compatib le accessories . Either the A or the B
output o n the Power supply may be us ed since these are id entical.
DevicesComputer
VNET
In Link
VNET
In Link
2627Quick Start GuideVNET USB RS232 INTERFACE
Devices
Computer
Diagram 2
USB
You can connec t your computer to th e VNET™ Interf ace via USB using a USB Type A to USB Type
B cable as in d iagram 2. It is not usuall y necessary to u se a Power Supply to power t he VNET™
Interf ace when using USB, since USB w ill supply sucie nt power for the Inter face. If there are
any Netwo rk powered device s on the network ho wever, then it will be neces sary to use the
Accessor y Power Supply
Connecting Devices
VNET
In Link
Connec t the VNET™ Link so cket on the VNET™ In terface to the VNE T™ In socket of the rst
device you w ish to control, then th e VNET™ Link socke t of this device to the VN ET™ In socket
of the nex t device, and so on. The o rder in which the dev ices are connec ted is not import ant.
The Link so cket of the last devi ce in the ‘chain’ need not be c onnected. The In s ocket of the
VNET™ In terface is intend ed for special app lications, and wou ld not normally be con nected.
The “Ether con” network con nectors are f ully compatible wi th standard RJ 45 Ethernet patch
cables w hich may be used to make th ese connecti ons. If additional r uggedness is re quired,
we recomme nd using the Neutri k Ethercon lockin g type of connec tor.
VNET
In Link
BvNet
Adapter
Racking
The VNET ™ Interface and Acce ssory Power Supp ly may be used free -standing.
If you wish to mo unt them in a 19-inch rac k, then the VNET ™ accessory rac k-mount kit may be
used. To mount an A ccessory in the M ounting Kit panel:
1. Rem ove the two mountin g brackets and blan king sheet which ar e covering the aper ture
you wish to mo unt the Accessor y in, by removing the t wo nuts. (Keep these a nd the screws
and washers).
2. Remove the t wo screws fro m one side of the Accesso ry
3. Using the t wo screws remove d in 2, attach one mo unting bracket lo osely to the side of th e
Accessor y, with the “ear” toward s the front, point ing outwards.
2829Quick Start GuideVNET USB RS232 INTERFACE
4. Repeat 2 an d 3 for the other side. Now p ush the lid towards th e back of the unit as fa r as it
will go then a lign the bracket ear s with the front e dge of the lid.
Now tighten the screws.
5. Oer t he Accessory wi th its mounting br ackets up
to the rever se side of the Mount ing Panel, and x it inpla ce using the two set s of screws,
washers a nd nuts removed in 1.
Note that th e holes at the rear ends o f the brackets may b e used as cable tie -o points
if desired.
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.