Klark Teknik DN 30T, DN 30R Specifications

DN 30T/DN 30R

2-Channel Dante Audio Receiver/Transmitter for High-Performance Networking

DN 30R DN 30T

(1) (2)(3) (5) (5) (6) (7)(2) (9)(3) (8)

(7)

(6)
(8)

(10) (9) (4) (13)(11) (12)

(1) Headphone output – Connect a pair of

headphones v ia ⁄" TRS cable. The volume can be
adjusted with the adjacent LE VEL knob.

(2) S YNC LED – The LED will light red when the unit

is powered on, and light green when the unit is
connecte d to an Ethernet network . A ashing green
LED indicates that the unit is in master clock mode,
and solid green indicates slave mode.

(3) S YS LED – The LED will light red while the unit

is booting up. Once Dante becomes active,
the LED will light green.

(4) SIGNAL LEDs – The left and r ight LEDs will light

green when signal is present on each channel.
The LEDs will light red when the input signal
approaches clipping.

(5) ETHERCON LEDs – The lef t LED lights green to

indicate data trac, and the right LED light s to
indicate successful Ethernet connection.

(6) ETHERCON port – Connects the unit to a Dante

network v ia CAT5e or CAT6 cable. Power can also
be supplied via this connec tion.

(7) ON LED – Lights when power is connec ted via the

included 24 V power adapter.

(8) PoE LED – Lights when the unit is receiving power

via the Ethernet port.

(9) DC INPUT – Connect the included power adapter if

you don’t plan to use PoE.

(10) EARTH LIFT – Removes the ground/earth

connection to remove unwanted noise.

(11) OUTPUT L/R – Conne ct to a mixing console or audio

interface via balanced XLR cables.

(12) INPUTS – Connec t an audio source via balanced

or unbalanced ¼" cables, RCA cable s, or a stereo
⁄" cable. All inpu ts are wired in parallel with one
another.

(13) LEVEL – Adjus ts the level of all input jack s. Start

with the knob at the center 12:00 position and turn
up if more signal is needed. Turn the k nob down if
the SIGNAL LEDs light solid red.

Specications

DN 30R DN 30T

Connectors

Ethernet 1 x RJ45 1 x RJ45

2 x ¼" TRS, 40 k balanced,

20 k unbalanced

Analogue audio inputs —

Max. input level — +22 dBu (sensitivity 0 dBu)

2 x XLR, 75  balanced

Analogue audio outputs

Max. outpu t level +22 dBu —

Phones 1 x ⁄" TRS, stereo —

Controls

Level

LED indicators Sync, Sys, On, PoE Signal, Sync, Sys, On, PoE

System

Frequency response 20 Hz to 20 kHz (±0.1 dB)

THD + N @ 1 kHz 0.0015% unweighted 0.0014% unweighted

Signal-to-noise ratio 98 dB 97 dB

Sample rate 44.1, 48, 88.2, 96 kHz

Dynamic range 116 dB unweighted

Crosstalk LR -110 dB -10 0 d B

Power adapter 24 V DC, 300 mA, center positive

Physical

Dimensions (H x W x D)

Without bumpers 54 x 108 x 103 mm (2.1 x 4.3 x 4.1")

With bumpers 63 x 118 x 112 mm (2.5 x 4.6 x 4.4")

Weight 0.7 kg (1.5 lbs)

⁄" TRS, stereo,

20  unbalanced

0 to -∞ dBu, adjustable

(phones only)

2 x RCA, 20 k unb alanced

1 x ⁄" TRS stereo,
20 k unbalanced

—

Sensitivity -20 to +20 dB,

adjustable

FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION

Klark Teknik

DN 30T/DN 30R

Responsible Party Name: Music Tribe Commercial NV Inc.

Address: 5270 Procyon Street

Las Vegas, NV 89118

Phone Number: [phone]

DN 30T/DN 30R

complies with the FCC rules as mentioned in the followingparagraph:

This equipment has been tested and found to comply with the limits for a ClassB
digital device, pur suant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc tions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation bet ween the equipment and receiver

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any person who
relies either wholly or in part upon any description, photograph, or statement contained
herein. Technical specications, appearances and other information are subject to
change without notice. All trademarks are the property of their respective owners.
Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon,
Behringer, Bugera and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online at
musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese Medicine Park, Nanlang Town,
528451, Zhongshan City, Guangdong Province, China

• Consult the dealer or an experienced radio/TV technician forhelp

This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any inter ference received, including inter ference that may
cause undesired operation.

Caution!

Any changes or modications not expressly approved by the part y responsible for
compliance could void the user's authority to operate the equipment.